Facile ZIF‐8 functionalized hierarchical micronanofiber membrane for high‐efficiency separation of water‐in‐oil emulsions

The efficient separation and recovery of oil from water‐in‐oil emulsion poses a great challenge because of the rapid development of the petrochemical industry throughout the world. In this study, a facile method to develop a ZIF‐8 functionalized hierarchical micronanofiber membrane for high‐efficiency oil/water separation was investigated. The electrospun PVDF/ZnO membrane was made, on which ZIF‐8 crystal seeds were then created with the revitalizing step and expanded in the growth step, and finally functionalized hierarchical micronanofiber PVDF‐g‐ZIF‐8 membrane was obtained. Results showed that oleophilic ZIF‐8 crystals on the surface of PVDF membrane dramatically increased the wettability of oil and tuned PVDF membrane from olephobicity to oleophilicity. The hydrophobic/lipophilic PVDF‐g‐ZIF‐8 membrane with a water contact angle up to 158° and a toluene contact angle down to 0° provides its separation efficiency for water‐in‐oil emulsion of 92.93% in an environmentally friendly and energy‐saving manner. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46462.     

Preparation and characterization of antifouling poly(vinylidene fluoride) blended membranes

Poly(vinylidene fluoride) (PVDF) membranes have been widely used in microfiltration and ultrafiltration because of their excellent chemical resistance and thermal properties. However, PVDF membranes have exhibited severe membrane fouling because of their hydrophobic properties. In this study, we investigated the antifouling properties of PVDF blended membranes. Antifouling PVDF blended membranes were prepared with a PVDF‐g‐poly(ethylene glycol) methyl ether methacrylate (POEM) graft copolymer. The PVDF‐g‐POEM graft copolymer was synthesized by the atom transfer radical polymerization (ATRP) method. The chemical structure and properties of the synthesized PVDF‐g‐POEM graft copolymer were determined by NMR, Fourier transform infrared spectroscopy, and gel permeation chromatography. To investigate the antifouling properties of the membranes, we prepared microfiltration membranes by using the phase‐inversion method, which uses various PVDF/PVDF‐g‐POEM concentrations in dope solutions. The pure water permeabilities were obtained at various pressures. The PVDF/PVDF‐g‐POEM blended membranes exhibited no irreversible fouling in the dead‐end filtration of foulants, including bovine serum albumin, sodium alginate, and Escherichia coli broth. However, the hydrophobic PVDF membrane exhibited severe fouling in comparison with the PVDF/PVDF‐g‐POEM blended membranes. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation of superhydrophobic nanocomposite fiber membranes by electrospinning poly(vinylidene fluoride)/silane coupling agent modified SiO2 nanoparticles

Superhydrophobic nanocomposite fiber membranes were prepared by blend electrospinning of poly(vinylidene fluoride) (PVDF) mixed with silane coupling agent modified SiO₂ nanoparticles. The nanoparticles were prepared by the sol–gel method, and the average particle diameter was measured by dynamic light scattering (DLS) and transmission electron microscopy (TEM). The effects of the type of silane coupling agent, such as n‐octyltriethoxysilane, vinyltrimethoxysilane (A‐171), and vinyltriethoxysilane (A‐151), and the mass ratio of the modified silica particles and PVDF on the surface wettability of the composite fiber membrane were investigated. The results indicated that the incorporation of silane coupling agent modified silica particles into the PVDF membrane increased the roughness of the surface and formed micro/nano dual‐scale structure compared to the pristine PVDF membrane, which was responsible for the superhydrophobicity and self‐cleaning property of the nanocomposite fiber membranes. The value of water contact angle (CA) increased with the increase of the content of modified SiO₂ nanoparticles in the nanocomposite membrane, ranging from 149.8° to 160.1° as the mass ratio of modified 170 nm SiO₂ with PVDF matrix increased from 0.5:1 to 5:1, indicating the membrane possesses a superhydrophobic surface. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44501.     

Dye removal using hydrophobic polyvinylidene fluoride hollow fibre composite membrane by vacuum membrane distillation

Hydrophobic polyvinylidene fluoride (PVDF) hollow fibre composite membranes were prepared by the dilute solution coating process to build a special surface structure that was similar to the dual micro‐nano structure on the lotus leaf. Poly(vinylidene fluoride‐co‐hexafluoropropene) was chosen as the hydrophobic polymer candidate in dilute solution. Membrane morphology and surface hydrophobicity were evaluated by scanning electron microscopy and dynamic water contact angle measurement. The prepared PVDF hollow fibre membranes were employed to separate dyes (Congo Red and Methylene Blue) from water by vacuum membrane distillation. The effects of operational conditions (feed temperature, vacuum pressure and feed flow rate) on the vacuum membrane distillation performance of different PVDF membranes were investigated. The results indicated that the water contact angle values of PVDF composite membrane surfaces improved from 93.6° to 130.8°, which was mainly attributed to the formation of micro‐nano rods. This structure was similar to the dual micro‐nano structure on the lotus leaf. Under test feed temperature, vacuum pressure and feed flow rate conditions, the dye rejection rate of Congo Red and Methylene Blue by the hydrophobic PVDF hollow fibre membrane remained above 99.5% and 99%, which was higher than that of the pristine PVDF membrane (99% and 98%, respectively). In addition, the hydrophobic PVDF hollow fibre composite membrane showed higher permeation flux under different conditions compared with the pristine PVDF membrane, which was attributed to membrane surface hydrophobicity and the electrostatic interactions between dyes and the PVDF membrane surface.     

Mixed Matrix PVDF/Graphene and Composite‐Skin PVDF/Graphene Oxide Membranes Applied in Membrane Distillation

This work elucidates the influence of graphene (G) and graphene oxide (GO) content on the desalination performance and scaling characteristics of G/polyvinylidene fluoride (G/PVDF) mixed matrix and GO/PVDF composite‐skin membranes, applied in a direct contact membrane distillation process (DCMD). Inclusion of high quality, nonoxidized, monolayered graphene sheets as polymer membrane filler, and application of a novel GO/water‐bath coagulation method for the preparation of the GO/PVDF composite films, took place. Water permeability and desalination tests via DCMD, revealed that the optimal G content was 0.87 wt%. At such concentration the water vapor flux of the G/PVDF membrane was 1.7 times that of the nonmodified reference, while the salt rejection efficiency was significantly improved (99.8%) as compared to the neat PVDF. Similarly the GO/PVDF surface‐modified membrane, prepared using a GO dispersion with low concentration (0.5 g/L), exhibited twofold higher water vapor permeate flux as compared to the neat PVDF, but however, its salt rejection efficiency was moderate (80%), probably due to pore wetting during DCMD. The relatively low scaling tendency observed for both G and GO modified membranes is primarily attributed to their smoother surface texture as compared to neat PVDF, while scaling is caused by the deposition of calcite crystals, identified by XRPD analysis. POLYM. ENG. SCI., 59:E262–E278, 2019. © 2018 Society of Plastics Engineers     

Porous poly(vinylidene fluoride) membrane with highly hydrophobic surface

The preparation of very hydrophobic poly(vinylidene fluoride) (PVDF) membranes was explored by using two methods. The first one was the modified phase inversion method using a water/N,N‐dimethylacetamide (DMAc) mixture instead of pure water as a soft precipitation bath. The second method was a precipitation‐bath free method, that is, the PVDF/DMAc casting solution underwent gelation in the open air instead of being immersed into a precipitation bath. The morphology of the surface and cross section of the membranes was investigated by using scanning electron microscopy (SEM). It was found that the membranes exhibited certain micro‐ and nanoscale hierarchical roughness on the surface, which brought about an enhanced hydrophobicity of the membrane. The contact angle (CA) of the samples obtained by the second method was as high as 150° with water. The conventional phase inversion method preparing PVDF porous membrane using pure water as precipitation bath usually results in an asymmetric membrane with a dense skin layer having a CA close to that of a smooth PVDF surface. The modified approach avoided the formation of a skin‐layer and resulted in a porous and highly hydrophobic surface of PVDF. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1358–1363, 2005     

Chitosan/ZIF‐8 Mixed‐Matrix Membranes for Pervaporation Dehydration of Isopropanol

Zeolitic imidazolate frameworks (ZIF‐8) nanoparticles were successfully synthesized and embedded into a chitosan (CS) polymeric matrix to prepare CS/ZIF‐8 mixed‐matrix membranes (MMMs) in order to investigate the effect of ZIF‐8 addition as novel filler on the dehydration performance of the CS polymeric membrane. MMMs were evaluated using pervaporation (PV) dehydration of isopropanol (IPA). The synthesized ZIF‐8 nanoparticles and MMMs were characterized by X‐ray diffraction, scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, Fourier transform infrared spectroscopy, and a swelling study. The PV performance of the prepared MMMs with different ZIF‐8 loadings for IPA dehydration was investigated. For the ZIF‐8/CS MMMs, at the optimum loading the total flux increases significantly with low separation factor reduction. The good PV performance of the ZIF‐8‐incorporated CS membranes for dehydration of IPA is demonstrated.     

Electrospinning of antibacterial poly(vinylidene fluoride) nanofibers containing silver nanoparticles

Poly(vinylidene fluoride) (PVDF) nanofibrous mats containing silver nanoparticles were prepared by electrospinning. The diameter of the nanofibers ranged between 100 and 300 nm, as revealed by scanning electron microscopy. The silver nanoparticles were dispersed, but some aggregation was observed with transmission electron microscopy. The content of silver nanoparticles incorporated into the PVDF nanofibrous mats was determined by inductively coupled plasma and X‐ray photoelectron spectroscopy. The antibacterial activities of the samples were evaluated with the colony‐counting method against Staphylococcus aureus (Gram‐positive) and Klebsiella pneumoniae (Gram‐negative) bacteria. The results indicate that the PVDF nanofibrous mats containing silver nanoparticles showed good antibacterial activity compared to the PVDF nanofiber control. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Modified poly(vinylidene fluoride) hollow fiber composite membranes reinforced by hydroxyapatite nanocrystal whiskers

The modified poly(vinylidene fluoride) (PVDF) hollow fiber composite membranes reinforced by hydroxyapatite (HAP) nanocrystal whiskers were fabricated with wet‐spinning method. The PVDF/HAP/N‐methyl‐2‐pyrrolidone dope solutions experienced delayed demixing mechanism, and the precipitation rate slightly increased as the HAP whisker content increased. The cross sections of PVDF‐HAP and neat PVDF hollow fiber composite membranes were composed of five distinct layers: two skin layers, two finger‐like sublayers, and a sponge‐like layer. The Young's modulus of and tensile strength of the PVDF‐HAP hollow fiber membranes gradually increased with the addition of nano‐HAP whiskers. The elongation ratio was also improved, which was different from the polymeric membranes modified by other inorganic nanofillers. The permeation flux of the PVDF‐HAP hollow fiber membranes slightly increased with the increase of HAP content in the composite membranes as its hydrophilicity was improved. The crystallization behaviors of PVDF in the composite membranes were also investigated. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Three‐component mixed matrix organic/inorganic hybrid membranes for pervaporation separation of ethanol–water mixture

Mixed matrix membranes (MMMs) were made by incorporating vinyltrimethoxysilane (VTMS)‐modified Silicalite‐1 zeolite nanoparticles (V‐Silicalite‐1 NPs) into fluorinated polybenzoxazine (F‐PBZ) modified polydimethylsiloxane (PDMS) polymer through in situ polymerization method. The membrane morphology, surface wettability, and pervaporation performance were systematically investigated. The addition of F‐PBZ into PDMS membranes resulted in substantially improved flux and marginal increase of separation factor, which is the result of higher free volume and higher hydrophobicity caused by the addition of F‐PBZ. The modification of Silicalite‐1 NPs improved the interfacial contact between zeolite crystals and polymer phase. The incorporation of hydrophobic V‐Silicalite‐1 zeolite NPs into the PDMS membranes led to much higher separation factor but reduced flux, which is the result of increased hydrophobicity and reduced free volume. The three‐component MMMs with V‐Silicalite‐1 zeolite NPs in the F‐PBZ fluorinated PDMS exhibited separation factor of 28.7 and flux of 0.207 kg m^?2 h^?1 for 5 wt % ethanol aqueous solution at 50 °C, while the pure PDMS membranes only had separation factor of 4.8 and flux of 0.088 kg m^?2 h^?1. The substantial increase of both flux and separation factor were attributed to the higher hydrophobicity and free volume caused by the incorporation of both hydrophobic zeolite crystals and F‐PBZ polymer into the PDMS membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44753.     

Recognition properties of poly(vinylidene fluoride) hollow‐fiber membranes modified by levofloxacin‐imprinted polymers

Through the use of thermal polymerization, poly(vinylidene fluoride) (PVDF) hollow‐fiber membranes modified by a thin layer of molecularly imprinted polymers (MIPs) were developed for the selective separation of levofloxacin. To demonstrate the changes induced by thermal polymerization, PVDF hollow‐fiber membranes with different modification degrees by repeated polymerization were weighed. The total weight of the imprinted membranes increased by 14 μg/cm² after a five‐cycle polymerization. An increase in the membrane weight indicated the deposition of an MIP layer on the external surface of PVDF hollow‐fiber membranes during each polymerization cycle, which was also characterized by scanning electron microscopy. MIP membranes with different degrees of surface modification provided highly selective binding of levofloxacin. Both hollow‐fiber MIP membranes and nonimprinted membranes showed enhanced adsorption of levofloxacin and ofloxacin gradually with an increase in the modification degrees of PVDF hollow‐fiber membranes to a maximum value followed by a decrease. These results indicate that thermal polymerization indeed produces an MIP layer on the external surface of PVDF hollow‐fiber membranes and that it is feasible to control the permeability by repeated polymerization cycles. Different solvent systems in the permeation experiments were used to understand the hydrophobic interaction as one of the results of the binding specificity of MIP membranes. Selective separation was obtained by multisite binding to the template via ionic, hydrogen‐bond, and hydrophobic interactions. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Octadecyl‐silica—PVDF membrane of superior MD desalination performance

Despite its widespread industrial and residential uses for production of potable water, the reverse osmosis (RO) desalination process has some drawbacks by discharging harmful concentrated saline water as reject stream. A hydrophobic porous membrane can treat such environmentally unfriendly RO reject stream via Membrane Distillation (MD) process. Here, we describe preparation of superior polyvinylidenefluoride (PVDF) membrane modified with superhydrophobic silica nanoparticles for desalination application. Superhydrophobicity (contact angle of 151°) of silica nanoparticles of 7 nm sizes was achieved by reaction of the silica particles with octadecyltrichlorosilane in toluene to form ? Si? O? Si? links with C18 alkyl chain. A homogeneous polymer dope mixture containing a desired amount of modified silica colloids suspended in toluene was used for the membrane preparation. The PVDF membrane with optimal silica content exhibited excellent flux with >99% salt rejection efficiency when used for MD at room temperature from the saline water feed of 3.5 wt % NaCl. The prepared hydrophobic PVDF membrane has the potential for MD application in treating the RO reject stream and other aqueous industrial effluents. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46043.     

ZIF‐11/Polybenzimidazole composite membrane with improved hydrogen separation performance

Zeolitic imidazolate framework (ZIF)‐11 crystals were prepared by the toluene‐assisted method, and they were incorporated into polysulfone, polyethersulfone, and polybenzimidazole (PBI) matrix to investigate the compatibility. ZIF‐11 had a good connection with PBI matrix as they had the same benzimidazole groups. The evaporation temperature of the membrane formation was studied with two different solvents: N‐methyl‐2‐pyrrolidone (NMP) and N,N‐dimethylacetamide (DMAc). Then, the ZIF‐11/PBI composite membranes prepared using NMP or DMAc as the solvent were characterized and tested by gas separation. Improved H₂ and CO₂ permeabilities with a H₂/CO₂ ideal selectivity of 5.6 were obtained on the 16.1 wt % ZIF‐11/PBI composite membrane prepared with DMAc as the solvent. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41056.     

Fabrication and characterization of electrolyte membranes based on organoclay/tripropyleneglycol diacrylate/poly(vinylidene fluoride) electrospun nanofiber composites

Utilizing polymer electrospinning technology, novel electrolyte membranes based on poly(vinylidene fluoride) (PVDF)/organomodified clay (OC)/tripropyleneglycol diacrylate (TPGDA) composite nanofibers with a diameter of 100–400 nm were fabricated for application in lithium batteries. Ultraviolet photo‐polymerization of electrospun PVDF/OC/TPGDA nanofibers generated chemically crosslinked TPGDA‐grafted PVDF/OC nanofibers exhibiting robust mechanical and electrochemical properties. The prepared fibrous PVDF/OC/TPGDA electrolytes were characterized in terms of morphology, crystallinity, electrochemical stability, ionic conductivity and cell cycleability. Based on differential scanning calorimetry analysis, the crystallinity of PVDF decreased by ca 10% on employing the OC and TPGDA. Compared with pure PVDF film‐based electrolyte membranes, the TPGDA‐ and OC‐modified PVDF electrolyte membranes exhibited improved mechanical properties and various electrochemical properties. The OC‐ and TPGDA‐modified microporous membranes are promising candidates for overcoming the drawbacks of the lower mechanical stability of fibrous‐type electrolytes with further improvement of electrochemical performance. Copyright © 2009 Society of Chemical Industry     

Preparation and properties of hydrophobic poly(vinylidene fluoride)–SiO2 mixed matrix membranes for dissolved oxygen removal from water

The application of the membrane method for removing dissolved oxygen (DO) from water on the laboratory scale was studied. Flat mixed matrix membranes were composed of poly(vinylidene fluoride) (PVDF) and hydrophobic nanosilica particles, which were used to improve the DO removal process. The SiO₂ particles were modified by a silane coupling agent and examined by Fourier transform infrared spectroscopy. It was shown that the surface of the SiO₂ particles was bonded to hydrophobic long‐chain alkane groups through chemical bonding. The effects of adding SiO₂ particles on the membrane properties and morphology were examined. The results show that the porosity and pore size of the membrane were affected by the introduction of SiO₂ particles, and the cross‐sectional morphology of the PVDF composite membranes changed from fingerlike macrovoids to a spongelike structure. The membrane performance of DO removal was evaluated through the membrane unit by a vacuum degassing process. It was found that the SiO₂/PVDF hybrid membranes effectively improved the oxygen removal efficiency compared with the original PVDF membranes. The maximum permeation flux was obtained when the loading amount was 2.5 wt %. The effect of the downstream vacuum level was also investigated. The experimental results show that the SiO₂/PVDF hybrid membranes had superior performances and could be an alternative membrane for removing DO from water. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40430.     

Antifouling enhancement of PVDF membrane tethered with polyampholyte hydrogel layers

The preparation and property of antifouling poly(vinylidene fluoride) (PVDF) membrane tethered with polyampholyte hydrogel layers were described in this work. In fabricating these membranes, the [2‐(methacryloyloxy)ethyl] trimethylammonium chloride and 2‐acrylamide‐2‐methyl propane sulfonic acid monomers were grafted onto the alkali‐treated PVDF membrane to yield polyampholyte hydrogel layers via radical copolymerization with N,N′‐methylenebisacrylamide as crosslinking agent. The analyses of fourier transform infrared attenuated total reflection spectroscopy and X‐ray photoelectron spectroscopy confirm the covalent immobilization of polyampholyte hydrogel layer on PVDF membrane surface. The grafting density of polyampholyte hydrogel layer increases with the crosslinking agent growing. Especially for the membrane with a high grafting density, a hydrogel layer can be observed obviously, which results in the complete coverage of membrane pores. Because of the hydrophilic characteristic of grafted layer, the modified membranes show much lower protein adsorption than pristine PVDF membrane. Cycle filtration tests indicate that both the reversible and irreversible membrane fouling is alleviated after the incorporation of polyampholyte hydrogel layer into the PVDF membrane. This work provides an effective pathway of covalently tethering hydrogel onto the hydrophobic membrane surface to achieve fouling resistance. POLYM. ENG. SCI., 55:1367–1373, 2015. © 2015 Society of Plastics Engineers     

Electrospun fiber membranes from blends of poly(vinylidene fluoride) with fouling‐resistant zwitterionic copolymers

Nonwoven super‐hydrophobic fiber membranes have potential applications in oil–water separation and membrane distillation, but fouling negatively impacts both applications. Membranes were prepared from blends comprising poly(vinylidene fluoride) (PVDF) and random zwitterionic copolymers of poly(methyl methacrylate) (PMMA) with sulfobetaine methacrylate (SBMA) or with sulfobetaine‐2‐vinylpyridine (SB2VP). PVDF imparts mechanical strength to the membrane, while the copolymers enhance fouling resistance. Blend composition was varied by controlling the PVDF‐to‐copolymer ratio. Nonwoven fiber membranes were obtained by electrospinning solutions of PVDF and the copolymers in a mixed solvent of N,N‐dimethylacetamide and acetone. The PVDF crystal phases and crystallinities of the blends were studied using wide‐angle X‐ray diffraction and differential scanning calorimetry (DSC). PVDF crystallized preferentially into its polar β‐phase, though its degree of crystallinity was reduced with increased addition of the random copolymers. Thermogravimetry (TG) showed that the degradation temperatures varied systematically with blend composition. PVDF blends with either copolymer showed significant increase of fouling resistance. Membranes prepared from blends containing 10% P(MMA‐ran‐SB2VP) had the highest fouling resistance, with a fivefold decrease in protein adsorption on the surface, compared to homopolymer PVDF. They also exhibited higher pure water flux, and better oil removal in oil–water separation experiments. © 2018 Society of Chemical Industry     

无机粒子改性聚偏氟乙烯超滤膜的研究进展

聚偏氟乙烯(PVDF)作为一种常见的超滤、微滤、渗透蒸发薄膜材料,具有优良的热稳定性、化学稳定性、疏水性及生物相容性等,在生物、医药等各个领域均表现出良好的应用前景。近年来,PVDF复合多孔膜的制备及应用成为材料界的研究热点,但由于PVDF材料具有较低的表面能,使其具有疏水性,存在过滤压力大、薄膜易受污染等问题,限制了其使用范围,因此需要对PVDF膜材料进行亲水改性。为此,在详细介绍PVDF结构及性能的基础上,总结了不同无机粒子改性PVDF复合多孔膜的最新研究进展,归纳了其常用制备方法及工艺,展望了PVDF复合材料的发展前景及研究方向。     

Influence of surface modification of zinc oxide nanoparticles on thermal behavior and hydrophilic property of PET–PEG composites

Zinc oxide (ZnO) nanoparticles were successfully prepared by a one‐step precipitation reaction in an aqueous solution of zinc acetate and sodium hydroxide with stearic acid (SA) as the modifying agent. Hydrophilic composites of poly(ethylene terephthalate) (PET), poly(ethylene glycol), and ZnO nanoparticles were prepared further by in situ polymerization. The surface modification of ZnO and the microstructure and properties of prepared nanoparticles were investigated by relative contact angle measurements (CA), Fourier transform infrared spectroscopy, X‐ray diffraction (XRD), scanning electron microscopy, and thermogravimetric analysis (TGA). Measurements of CA and XRD indicated that the surface‐treated ZnO was hydrophobic and had a significant improvement in crystallinity with SA. Compared with the nanocomposites filled with the pure ZnO, the modified ZnO exhibits a better dispersion in PET–PEG matrix. TGA results showed that the presence of modified ZnO nanoparticles can improve the thermal stability of PET–PEG matrix. CA and low field nuclear magnetic resonance methods were used to investigate the hydrophilic behavior of nanocomposites. The results revealed that modified nanoparticles had a positive effect on the bound water absorption. A simple model for the interactions between ZnO, SA, and PET–PEG matrix was proposed. POLYM. COMPOS., 37:1830–1838, 2016. © 2015 Society of Plastics Engineers     

Poly(vinyl alcohol)/ZIF‐8‐NH2 mixed matrix membranes for ethanol dehydration via pervaporation

Ethanediamine‐modified zeolitic imidazolate framework (ZIF)‐8 particles (ZIF‐8‐NH₂) is synthesized and incorporated in the poly(vinyl alcohol) (PVA) matrix to fabricate novel PVA/ZIF‐8‐NH₂ mixed matrix membranes (MMMs) for pervaporation dehydration of ethanol. The PVA/ZIF‐8‐NH₂ MMMs exhibit enhanced membrane homogeneity and separation performance because of the higher hydrophilicity and restricted agglomeration of the particles, as compared to corresponding MMMs loaded with unmodified particles. The effect of ZIF‐8‐NH₂ loading in the MMMs is studied and the MMM with a 7.5 wt % ZIF‐8‐NH₂ loading shows the best pervaporation performance for ethanol dehydration at 40°C. Various characterization techniques (Fourier transform infrared, scanning electron microscope, contact angle, sorption test, etc.) are used to investigate the MMMs loaded with ZIF‐8 and ZIF‐8‐NH₂ particles. The impact of operation conditions on pervaporation performance is also performed. The performance benchmarking shows that the MMMs have superior separation factors and comparable flux to most other PVA hybrid membranes. © 2016 American Institute of Chemical Engineers AIChE J, 62: 1728–1739, 2016