Promoted adsorption of CO2 on amine‐impregnated adsorbents by functionalized ionic liquids

Amine‐impregnated adsorbents are promising alternatives to aqueous amines for CO₂ capture. However, the diffusion‐controlled CO₂ adsorption process is a significant issue associated with them, resulting in the insufficient utilization of amine groups. Herein, we propose the use of functionalized ionic liquids 1‐ethyl‐3‐methylimidazolium acetate ([emim][Ac]) with chemical reactivity to CO₂ and low viscosity as the additive to amine‐impregnated adsorbents. The key is that [emim][Ac] does not show drastic increase in viscosity after reacting with CO₂. Taking the polyethyleneimine (PEI)‐impregnated SBA‐15 as a model system, it is found that the CO₂ capacities of PEI/SBA‐15 composites are improved by 86%, and the active site efficiencies are improved by 270%, after the addition of [emim][Ac]. The addition of [emim][Ac] to PEI/SBA‐15 composites also helps improve the CO₂ adsorption rate and recycling stability of composites. Therefore, [emim][Ac] offers the opportunity to fabricate amine‐impregnated adsorbents with simultaneously improved CO₂ capacities, adsorption kinetics, and recycling stability. © 2018 American Institute of Chemical Engineers AIChE J, 64: 3671–3680, 2018     

Synthesis and CO2 adsorption behavior of amine‐functionalized porous polystyrene adsorbent

A solid amine adsorbent was prepared by modifying a porous polystyrene resin (XAD‐4) with chloroacetyl chloride through a Friedel–Crafts acylation reaction, followed by aminating with tetraethylenepentamine (TEPA). The adsorption behavior of CO₂ from a simulated flue gas on the solid amine adsorbent was evaluated. Factors that could determine the CO₂ adsorption performance of the adsorbents such as amine species, adsorption temperature, and moisture were investigated. The experimental results showed that the solid amine adsorbent modified with TEPA (XAD‐4‐TEPA), which had a longer chain, showed an amine efficiency superior to the other two amine species with shorter chains. The CO₂ adsorption capacity decreased obviously as the temperature increased because the reaction between CO₂ and amine groups was an exothermic reaction, and its adsorption amount reached 1.7 mmol/g at 10 °C in dry conditions. The existence of water could significantly increase the CO₂ adsorption amount of the adsorbent by promoting the chemical adsorption of CO₂ on XAD‐4‐TEPA. The adsorbent kept almost the same adsorption amount after 10 cycles of adsorption–desorption. All of these results indicated that amine‐functionalized XAD‐4 resin was a promising CO₂ adsorbent. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45046.     

Chemical solvent in chemical solvent: A class of hybrid materials for effective capture of CO2

Amino acid ionic liquids (AAILs) are chemical solvents with high reactivity to CO₂. However, they suffer from drastic increase in viscosity on the reaction with CO₂, which significantly limits their application in the industrial capture of CO₂. In this work, 1‐ethyl‐3‐methylimidazolium acetate ([emim][Ac]) which also exhibits chemical affinity to CO₂ but low viscosity, and its viscosity does not increase drastically after CO₂ absorption, was proposed as the diluent for AAILs to fabricate hybrid materials. The AAIL+[emim][Ac] hybrids were found to display enhanced kinetics for CO₂ absorption, and their viscosity increase after CO₂ absorption are much less significant than pure AAILs. More importantly, owing to the fact that [emim][Ac] itself can absorb large amount of CO₂, the AAIL+[emim][Ac] hybrids still have high absolute capacities of CO₂. Such hybrid materials consisting of a chemical solvent plus another chemical solvent are believed to be a class of effective absorbents for CO₂ capture. © 2017 American Institute of Chemical Engineers AIChE J, 64: 632–639, 2018     

Synthesis of new crosslinked porous ammonium‐based poly(ionic liquid) and application in CO2 adsorption

A new poly(ionic liquid) of N,N‐methylenebisacrylamide (MBA)‐crosslinked‐poly(4‐vinylbenzyltriethylammonium hexafluorophosphate)(MBA‐crosslinked‐P[VBTEA][PF₆]) is prepared through the ion exchange of KPF₆ with the precursor of MBA‐crosslinked‐P[VBTEA][Cl]; the precursor is synthesized by 4‐vinylbenzyltriethylammonium chloride and MBA via inverse suspension polymerization. MBA‐crosslinked‐P[VBTEA][PF₆] is a thermally stable (decomposes at nearly 300°C) and porous (apparent porosity of 64.3% and specific surface of 39.12 m²/g) polymer particle with high purity, as indicated by Fourier transformed infrared, energy dispersive spectroscopy, thermogravimetric, scanning electron microscopy, and porous analyses. It is observed that MBA‐crosslinked‐P[VBTEA][PF₆] has good CO₂ adsorption capability of 14.04 mg/g at 0.2 MPa and 25°C, and can be recovered by desorption at vacuum and 80°C, and reused with 99% CO₂ adsorption after four cycles. POLYM. ENG. SCI., 54:59–63, 2014. © 2013 Society of Plastics Engineers     

Hypercrosslinked silole‐containing microporous organic polymers with N‐functionalized pore surfaces for gas storage and separation

Novel hypercrosslinked microporous organic polymers (MOPs) derived from N‐functionalized siloles as basic building units have been designed and synthesized via Friedel–Crafts alkylation reaction. The resulting N‐functional silole‐containing polymer networks exhibit high thermal stabilities and moderate Brunauer–Emmett–Teller surface area ranging from 666 to 1137 m² g^?1. The incorporation of carbazole or triphenylamine moieties into the polymer skeleton increases the number of electron donating basic nitrogen sites in the porous frameworks. Thus, the corresponding polymer PDMCzS shows enhanced CO₂ adsorption capacities of 3.23 mmol g^?1 at 273 K and 1.13 bar, and higher CO₂/N₂ selectivity (43.99) at 273 K than the analogous silole‐containing polymers P1–P3. These results demonstrated that the N‐functionalized silole‐containing polymer network is a very promising candidate for potential applications in post‐combustion CO₂ capture and sequestration. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45907.     

CO2 sorption performance by aminosilane functionalized spheres prepared via co‐condensation and post‐synthesis methods

Amine functionalized silica microspheres were synthesised via a modified Stöber reaction for carbon dioxide (CO₂) adsorption. A number of adsorbents were synthesized by co‐condensation and post synthesis immobilization of amines on porous silica spheres. CO₂ adsorption studies were carried out on a fixed bed gas adsorption rig with online mass spectrometry. Amine co‐condensed silica spheres were found to adsorb up to 66 mg CO₂ g^?1 solid in a 0.15 atm CO₂ stream at 35°C. Simple post‐synthesis addition of aminopropyltriethoxysilane to amine co‐condensed silica was found to significantly increase the uptake of CO₂ to 211 mg CO₂ g^?1 under similar conditions, with CO₂ desorption commencing at temperatures as low as 60°C. The optimum temperature for adsorption was found to be 35°C. This work presents a CO₂ adsorbent prepared via a simple synthesis method, with a high CO₂ adsorption capacity and favorable CO₂ adsorption/desorption performance under simulated flue gas conditions. © 2016 American Institute of Chemical Engineers AIChE J, 62: 2825–2832, 2016     

Ionic Liquid with Silyl Substituted Cation: Thermophysical and CO2/N2 Permeation Properties

Novel functionalized ionic liquid (IL) combining an imidazolium‐based cation with branched alkyl chain bearing silyl group, 1‐methyl‐3‐(2‐methyl‐3‐(trimethylsilyl)propyl)imidazolium ([Si?C₁?C₃‐mim]⁺), and bis(trifluoromethylsulfonyl)imide ([NTf₂]^?) anion was synthesized and its thermophysical properties (density, viscosity, surface tension, surface entropy and enthalpy, thermal stability) were studied in a wide temperature range and compared with those of ILs having linear alkyl ([C_n‐mim][NTf₂]) and siloxane ([(SiOSi)C₁mim][NTf₂]) side chains. It was found that at 25 °C [Si?C₁?C₃‐mim][NTf₂] is a liquid with dynamic viscosity of 224 cP (224 mPa s) and density of 1.32 g cm^?3. The presence of side branched alkyl chain with trimethylsilyl end‐group prevents crystallization of IL and leads to higher viscosities and lower densities in comparison with commonly known [C_n‐mim][NTf₂] (n=2–4). As surface excess enthalpy was found to be in the lower end of the usual range of values for ILs, the interactions between silyl‐functionalized cation and [NTf₂] anion can be considered as relatively weak. Finally, [Si?C₁?C₃‐mim][NTf₂] was used for the preparation of polymer supported ionic liquid membranes (SILMs) and their CO₂ and N₂ permeation properties at 20 °C and 100 kPa were determined: permeability PCO₂=311, PN₂=12 Barrer, diffusivity DCO₂=115×10¹², DN₂=227×10¹² m² s^?1 and CO₂/N₂ permselectivity αCO₂/N₂=25.3.     

Graphene oxide functionalized by poly(ionic liquid)s for carbon dioxide capture

Poly(ionic liquid)s have been demonstrated as high efficient CO₂ absorbents. In the current study, a kind of poly(ionic liquid)s, Poly[2‐(methacryloyloxy)‐ethyl] trimethylammonium tetrafluoroborate (P[MATMA][BF₄]) was used to functionalize graphene oxide (GO). The hybrid in which P[MATMA][BF₄] was covalently bonded on GO platelets was prepared by a simple method, that is, traditional radical polymerization. The characterizations based on transmission electron microscopy, scanning electron microscope, Fourier transform infrared spectroscopy, Raman spectroscopy, X‐ray diffraction, and X‐ray photoelectron spectroscopy demonstrated the graft of P[MATMA][BF₄] on GO. N₂ adsorption measurements indicated that P[MATMA][BF₄] also greatly increased the specific surface area of GO. Due to the higher specific surface area and the CO₂ affinity of P[MATMA][BF₄], the GO‐P[MATMA][BF₄] hybrid exhibited a much higher CO₂ adsorption capacity compared with GO, GO‐NH₂, and P[MATMA][BF₄]. Their study showed that the combinations of poly(ionic liquid)s and GO could be promising CO₂ absorbents. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44592.     

Polymeric ionic liquid modified silica for CO2 adsorption and diffusivity

Two types of polymeric ionic liquids (PILs) modified porous silica for CO₂ sorption were synthesized by the polymerization of dialkylphosphate di‐butyl phosphate [VYIM][Bu₂PO₄] and 1‐allyl‐3‐methylimidazolium tetrafluoroborate [AMIM][BF₄] with alkoxyl‐modified silica. The PILs‐modified silica (SiO₂‐P[VYIM][Bu₂PO₄] and SiO₂‐P[AMIM][BF₄]) were evaluated by CO₂ adsorption isotherms at 273 K for investigating the porous structures. The adsorption and desorption behaviors of CO₂ (at 298, 313, and 333 K) and N₂ (at 313 K) up to 0.2 MPa were also investigated using a gravimetric method. In comparison with bare silica, the grafting of PILs on the support surface leads to a loss of microporosity, resulting in a slight decrease in CO₂ sorption capacity. The difference of CO₂ sorption capacity between SiO₂‐P[VYIM][Bu₂PO₄] and SiO₂‐P[AMIM][BF₄] is little, especially under 0.1 MPa. CO₂/N₂ selectivity is however notably improved, and especially [AMIM][BF₄] modified silica shows the best performance. The homogeneous surface diffusion model (HSDM) was used to estimate the diffusivities and good agreement between experimental values and fitting curves was obtained. The diffusion coefficients of CO₂ in the PILs‐modified silica are level with that of bare silica at level of 10⁻⁷−10⁻⁸ m²/s, about two to three orders of magnitude faster than that of reported [BMIM][BF₄]. POLYM. COMPOS., 38:759–766, 2017. © 2015 Society of Plastics Engineers     

Efficient capture of carbon dioxide with novel mass‐transfer intensification device using ionic liquids

A novel mass‐transfer intensified approach for CO₂ capture with ionic liquids (ILs) using rotating packed bed (RPB) reactor was presented. This new approach combined the advantages of RPB as a high mass‐transfer intensification device for viscous system and IL as a novel, environmentally benign CO₂ capture media with high thermal stability and extremely low volatility. Amino‐functionalized IL (2‐hydroxyethyl)‐trimethyl‐ammonium (S)?2‐pyrrolidinecarboxylic acid salt ([Choline][Pro]) was synthesized to perform experimental examination of CO₂ capture by chemical absorption. In RPB, it took only 0.2 s to reach 0.2 mol CO₂/mol IL at 293 K, indicating that RPB was kinetically favorable to absorption of CO₂ in IL because of its efficient mass‐transfer intensification. The effects of operation parameters on CO₂ removal efficiency and IL absorbent capacity were studied. In addition, a model based on penetration theory was proposed to explore the mechanism of gas–liquid mass transfer of ILs system in RPB. © 2013 American Institute of Chemical Engineers AIChE J, 59: 2957–2965, 2013     

Improving Physical Adsorption of CO2 by Ionic Liquids‐Loaded Mesoporous Silica

CO₂ sorption capacities of the neat and silica‐supported 1‐butyl‐3‐methylimidazolium‐based ionic liquids (ILs) were measured under atmospheric pressure. The silica‐supported ILs were synthesized by the impregnation‐vaporization method and charactrized by N₂ adsorption/desorption and thermogravimeteric analysis (TGA). Evaluation of the effects of influential factors on sorption capacity demonstrated that by increase of the temperature, flow rate, and the weight percentage of ILs in sorbents, the sorption capacity decreases. Among the sorbents, [Bmim][TfO] and SiO₂‐[Bmim][BF₄](50) had the highest capacity. By increasing the IL portion in SiO₂‐[Bmim][BF₄], the selectivity for CO₂ to CH₄ could be improved. The CO₂‐rich sorbents could be easily recycled.     

分子筛SBA-15负载离子液体[P66614][Triz]脱除氢烷气中CO2

以高效吸收CO₂的离子液体（IL）[P₆₆₆₁₄][Triz]作为吸收剂,通过浸渍法负载到两种不同孔径的介孔分子筛SBA-15上,用于脱除生物氢烷气中CO₂,并利用N₂吸附仪、扫描电子显微镜（SEM）和高倍透射电子显微镜（HRTEM）对负载材料进行了表征分析。混合吸收剂SBA-15（4.3 nm）-50%[Triz]的吸收容量和吸收速率比SBA-15（6.6 nm）-50%[Triz]的分别提高了12.4%和95.1%,这是由于SBA-15（4.3 nm）的孔道长度更短,避免了填充在孔道内的[P₆₆₆₁₄][Triz]在反应过程中接触不到CO₂,从而比SBA-15（6.6 nm）-50%[Triz]有更多IL反应活性点参与反应。还研究了不同氢烷气速率下SBA-15（4.3 nm）-50%[Triz]对CO₂的吸收并与2种吸附动力学模型相拟合,结果表明SBA-15（4.3 nm）-50%[Triz]对CO₂的吸收更符合准二级吸附动力学模型,表明吸附过程受化学吸附机理的控制,验证了[P₆₆₆₁₄][Triz]是通过化学反应脱除CO₂。     

Application of polyethylenimine‐impregnated solid adsorbents for direct capture of low‐concentration CO2

A systematic study of CO₂ capture on the amine‐impregnated solid adsorbents is carried out at CO₂ concentrations in the range of 400–5000 ppm, relating to the direct CO₂ capture from atmospheric air. The commercially available polymethacrylate‐based HP2MGL and polyethylenimine are screened to be the suitable support and amine, respectively, for preparation of the adsorbent. The adsorbents exhibit an excellent saturation adsorption capacity of 1.96 mmol/g for 400 ppm CO₂ and 2.13 mmol/g for 5000 ppm CO₂. Moisture plays a promoting effect on CO₂ adsorption but depends on the relative humidity. The presence of O₂ would lead to the decrease of adsorption capacity but do not affect the cyclic performance. The diffusion additive is efficient to improve the adsorption capacity and cyclic performance. Moreover, the adsorbents can be easily regenerated under a mild temperature. This study may have a positive impact on the design of high‐performance adsorbents for CO₂ capture from ambient air. © 2014 American Institute of Chemical Engineers AIChE J, 61: 972–980, 2015     

Enhanced gravimetric CO2 capacity and viscosity for ionic liquids with cyanopyrrolide anion

Ionic Liquids (ILs) are considered as alternative solvents for the separation of CO₂ from flue gas due mainly to their CO₂ affinity and thermal stability. The cation architecture in a matrix of ammonium and mostly phosphonium‐based ILs with 2‐cyanopyrrolide as the anion to evaluate its impact on gravimetric CO₂ absorption capacity, viscosity, and thermal stability and the three fundamental properties vital for application realization are systematically investigated. Among the investigated ILs, [P2,2,2,8][2‐CNpyr] demonstrated the lowest viscosity, 95 cP at 40°C, and highest CO₂ uptake, 114 mg CO₂ per g IL at 40°C. Combined effects of asymmetry and the optimized chain lengths also resulted in improved thermal stability for [P2,2,2,8][2‐CNpyr], with a mass loss rate of 1.35 × 10^?6 g h^?1 (0.0067 mass % h^?1) at 80°C. © 2015 American Institute of Chemical Engineers AIChE J, 61: 2280–2285, 2015     

Effect of pH on Fumaric Acid Adsorption onto IRA900 Ion Exchange Resin

The effects of pH on fumaric acid adsorption onto IRA900 ion exchange resin were studied. The optimum pH with the highest adsorption capacity depended on the fumarate concentration: the optimum pH was > 4.0 for fumarate concentrations < 5.0 g/L and < 3.0 for higher concentrations. Such different adsorption behaviors of IRA900 resins at different pHs were attributed to the different ion forms of fumarate present in solution at different pHs. Modeling results showed that the two-site-occupancy adsorption reaction between FA^2? and resin active sites contributed to the high adsorption capacity at pH 5, whereas the intraparticle diffusion resulting from the hydrophobic interaction between H₂FA and the hydrophobic resin backbone of IRA900 increased significantly and led to a higher adsorption capacity at pH 3.     

A highly stable metal‐organic framework with optimum aperture size for CO2 capture

We herein report an optimal modulated hydrothermal (MHT) synthesis of a highly stable zirconium metal‐organic framework (MOF) with an optimum aperture size of 3.93 Å that is favorable for CO₂ adsorption. It exhibits excellent CO₂ uptake capacities of 2.50 and 5.63 mmol g^?1 under 0.15 and 1 bar at 298 K, respectively, which are among the highest of all the pristine water‐stable MOFs reported so far. In addition, we have designed a lab‐scale breakthrough set‐up to study its CO₂ capture performance under both dry and wet conditions. The velocity at the exit of breakthrough column for mass balance accuracy is carefully measured using argon with a fixed flow rate as the internal reference. Other factors that may affect the breakthrough dynamics, such as pressure drop and its impact on the roll‐up of the weaker component have been studied in details. © 2017 American Institute of Chemical Engineers AIChE J, 63: 4103–4114, 2017     

Synthesis of PEG‐functionalized poly(diphenylacetylene)s and their gas permeation properties

The polymerizations of 1‐(3‐methylphenyl)‐2‐(4‐trimethylsilyl)phenylacetylene ( 1a ) and 1‐(4‐methylphenyl)‐2‐(4‐trimethylsilyl)phenylacetylene ( 1b ) were carried out with TaCl₅‐n‐Bu₄Sn to give relatively high‐molecular‐weight polymers ( 2a and 2b ) (M_n > 5 × 10⁵). The obtained polymers were brominated by using benzoyl peroxide and N‐bromosuccinimide first, followed by substitution reaction of three types of polyethylene glycol. When diethylene glycol was used as a reagent on substitution reaction of meta‐substituted polymer, PEG‐functionalized poly(diphenylacetylene) with the highest content of oxyethylene unit [ 4a(2) ] was obtained, and the degree of substitution was 0.60. The degrees of substitution decreased to 0.15 and 0.08 when the polyethylene glycols with higher molecular weights were used. PEG‐substitution reaction to the para‐substituted polymers was difficult to proceed, and hence the degree of substitution was 0.18 even when diethylene glycol was used. The CO₂/N₂ separation factor of PEG‐functionalized polymer [ 4a(2) ] was as large as 28.8, although that of 2a was 7.41. The other PEG‐functionalized polymers also exhibited high CO₂ permselectivity, and their CO₂/N₂ separation factors were over 20. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Self‐healing imidazolium‐based ionene‐polyamide membranes: an experimental study on physical and gas transport properties

A new series of six imidazolium‐based ionenes containing aromatic amide linkages has been developed. These ionene‐polyamides are all constitutional isomers varying in the regiochemistry of the amide linkages (para, meta) and xylyl linkages (ortho, meta, para) along the polymer backbone. The physical properties as well as the gas separation behaviors of the corresponding membranes have been extensively studied. These ionene‐polyamide membranes show excellent thermal and mechanical stabilities, together with self‐healing and shape memory characteristics. Most importantly, [TC‐API(p)‐Xy][Tf₂N] and [IC‐API(m)‐Xy][Tf₂N] membranes (TC, terephthaloyl chloride; API, 1‐(3‐aminopropyl)imidazole; Xy, xylyl; Tf₂N, bis(trifluoromethylsulfonyl) imide; IC, isophthaloyl chloride), where the amide and xylyl linkages are attached at para and meta positions, exhibit superior selectivity for CO₂/CH₄ and CO₂/N₂ gas pairs. We also demonstrate the transport properties and diverse applicability of our newly developed ionene‐polyamides, particularly [TC‐API(p)‐Xy][Tf₂N], for various industrial applications. © 2019 Society of Chemical Industry     

N‐doped porous carbons for CO2 capture: Rational choice of N‐containing polymer with high phenyl density as precursor

N‐doped porous carbons (NPCs) are highly promising for CO₂ capture, but their preparation is severely hindered by two factors, namely, the high cost of N‐containing polymer precursors and the low yield of carbon products. Here we report for the first time the fabrication of NPCs through the rational choice of the polymer NUT‐4, with low cost and high phenyl density, as precursor. For the material NPC‐600 obtained from carbonization at 600°C, the yield is as high as 52.1%. The adsorption capacity of CO₂ on NPC‐600 reaches 6.9 mmol/g at 273 K and 1 bar, which is obviously higher than that on the benchmarks, including 13X zeolite (4.1 mmol/g) and activated carbon (2.8 mmol/g), as well as most reported carbon materials. Our results also demonstrate that the present NPCs can be completely regenerated under mild conditions. The abundant microporosity and “CO₂‐philic” (N‐doped) sites are responsible for the adsorption performance. © 2016 American Institute of Chemical Engineers AIChE J, 63: 1648–1658, 2017     

Ethylene/1‐octadecene copolymerization using [η5:η1‐C5Me4‐4‐R1‐6‐R‐C6H2O]TiCl2 catalysts

Copolymerization of ethylene with 1‐octadecene was studied using [η⁵:η¹‐C₅Me₄‐4‐R₁‐6‐R‐C₆H₂O]TiCl₂ [R₁ = ^tBu (1), H (2, 3, 4); R = ^tBu (1, 2), Me (3), Ph (4)] as catalysts in the presence of Al(i‐Bu)₃ and [Ph₃C][B(C₆F₅)₄]. The effect of the concentration of comonomer in the feed and Al/Ti molar ratio on the catalytic activity and molecular weight of the resultant copolymer were investigated. The substituents on the phenyl ring of the ligand affect considerably both the catalytic activity and comonomer incorporation. The 1 /Al(i‐Bu)₃/[Ph₃C][B(C₆F₅)₄] catalyst system exhibits the highest catalytic activity and produces copolymers with the highest molecular weight, while the 2 /Al(i‐Bu)₃/[Ph₃C][B(C₆F₅)₄] catalyst system gives copolymers with the highest comonomer incorporation under similar conditions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011