Vapour–liquid equilibrium of CO2 in aqueous solutions of N‐methyl‐2‐ethanolamine

The equilibrium solubility of CO₂ into aqueous solution of sterically hindered N‐methyl‐2‐ethanolamine or methyl amino ethanol (MAE) was investigated in the temperature range of 303.1–323.1 K and total CO₂ pressure in the range of 1–350 kPa. The N‐methyl‐2‐ethanolamine aqueous solutions studied were 0.968, 1.574, 2.240 and 3.125 mol kg^?1 of solvent. © 2011 Canadian Society for Chemical Engineering     

Kinetics of CO2 absorption into a novel 1‐diethylamino‐2‐propanol solvent using stopped‐flow technique

A stopped‐flow apparatus was used to measure the kinetics of carbon dioxide (CO₂) absorption into aqueous solution of 1‐diethylamino‐2‐propanol (1DEA2P) in terms of observed pseudo‐first‐order rate constant (k_o) and second‐order reaction rate constant (k₂), in this work. The experiments were conducted over a 1DEA2P concentration range of 120–751 mol/m³, and a temperature range of 298–313 K. As 1DEA2P is a tertiary amine, the base‐catalyzed hydration mechanism was, then, applied to correlate the experimental CO₂ absorption rate constants obtained from stopped‐flow apparatus. In addition, the pK_a of 1DEA2P was experimentally measured over a temperature range of 278–333 K. The Brønsted relationship between reaction rate constant (obtained from stopped‐flow apparatus) and pK_a was, then, studied. The results showed that the correlation based on the Brønsted relationship performed very well for predicting the absorption rate constant with an absolute average deviation of 5.2%, which is in an acceptable range of less than 10%. © 2014 American Institute of Chemical Engineers AIChE J, 60: 3502–3510, 2014     

Gas permeation performance of cellulose hollow fiber membranes made from the cellulose/N‐methylmorpholine‐N‐oxide/H2O system

Cellulose hollow fiber membranes (CHFM) were prepared using a spinning solution containing N‐methylmorpholine‐N‐oxide as solvent and water as a nonsolvent additive. Water was also used as both the internal and external coagulant. It was demonstrated that the phase separation mechanism of this system was delayed demixing. The CHFM was revealed to be homogeneously dense structure after desiccation. The gas permeation properties of CO₂, N₂, CH₄, and H₂ through CHFM were investigated as a function of membrane water content and operation pressure. The water content of CHFM had crucial influence on gas permeation performance, and the permeation rates of all gases increased sharply with the increase of membrane water content. The permeation rate of CO₂ increased with the increase of operation pressure, which has no significant effect on N₂, H₂, and CH₄. At the end of this article a detailed comparison of gas permeation performance and mechanism between the CHFM and cellulose acetate flat membrane was given. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1873–1880, 2004     

Functionalization of the 3′‐Ends of DNA and RNA Strands with N‐ethyl‐N‐coupled Nucleosides: A Promising Approach To Avoid 3′‐Exonuclease‐Catalyzed Hydrolysis of Therapeutic Oligonucleotides

The development of nucleic acid derivatives to generate novel medical treatments has become increasingly popular, but the high vulnerability of oligonucleotides to nucleases limits their practical use. We explored the possibility of increasing the stability against 3′‐exonucleases by replacing the two 3′‐terminal nucleotides by N‐ethyl‐N‐coupled nucleosides. Molecular dynamics simulations of 3′‐N‐ethyl‐N‐modified DNA:Klenow fragment complexes suggested that this kind of alteration has negative effects on the correct positioning of the adjacent scissile phosphodiester bond at the active site of the enzyme, and accordingly was expected to protect the oligonucleotide from degradation. We verified that these modifications conferred complete resistance to 3′‐exonucleases. Furthermore, cellular RNAi experiments with 3′‐N‐ethyl‐N‐modified siRNAs showed that these modifications were compatible with the RNAi machinery. Overall, our experimental and theoretical studies strongly suggest that these modified oligonucleotides could be valuable for therapeutic applications.     

Untersuchung der CO2‐Absorptionskinetik in wässrigen Lösungen von N,N‐Diethylethanolanmin und N‐Ethylethanolamin

N‐Ethylethanolamine (EEA) and N,N‐diethylethanolamine (DEEA) represent promising alkanolamines for CO₂ removal from gaseous streams, as they can be prepared from renewable resources. In this work, the reaction rate constant for the reaction between CO₂ and EEA and the liquid‐side mass transfer coefficient were determined from the absorption rate measurements in a blend comprising DEEA, EEA and H₂O. A stirred‐cell reactor was applied for the absorption studies, whereas a zwitterion mechanism for EEA and a base‐catalyzed hydration mechanism for DEEA were used to describe the reaction kinetics.     

DEA溶液吸收/再生CO2的研究

化学溶液法脱除CO2是工业中一项传统的净化气体的方法。DEA是目前回收烟道气中低浓度CO2所使用的最主要试剂,本实验进行DEA吸收CO2的实验,掌握了溶液pH值与CO2浓度变化的情况,并用这一方法进行测定CO2浓度的研究。通过考察溶液的再生情况,了解再生温度对溶液再生效果的影响。     

MDEA-MEA混合醇胺脱硫脱碳的模拟计算

实验研究了N-甲基二乙醇胺(MDEA)和乙醇胺(MEA)混合有机胺水溶液吸收煤气中H_2S和CO_2的过程。采用严格的混合溶剂电解质理论建立了气体吸收的热力学计算模型,并用模拟计算软件(ASPEN PLUS)计算了H_2S和CO_2混合气的吸收过程,计算值和实验值符合良好。实验数据和模拟计算结果表明,采用混合醇胺脱硫具有较好的脱硫效率和选择性,符合目前工业装置对脱硫的要求。     

A Study on CO2 Absorption Kinetics by Aqueous Solutions of N,N‐Diethylethanolamine and N‐Ethylethanolamine

N‐Ethylethanolamine (EEA) and N,N‐diethylethanolamine (DEEA) represent promising candidate alkanolamines for CO₂ removal from gaseous streams, as they can be prepared from renewable resources. In this work, the reaction rate constant for the reaction between CO₂ and EEA was determined from the absorption rate measurements of CO₂ in a blend comprising DEEA, EEA and H₂O. A stirred‐cell reactor with a plane, horizontal gas‐liquid interface was used for the absorption studies. While the DEEA concentration in the formulated solution was varied in the range of 1.5–2.5 kmol/m³, the initial EEA concentration was 0.1 kmol/m³. A zwitterion mechanism for EEA and a base‐catalyzed hydration mechanism for DEEA were used to describe the reaction kinetics. At 303 K, the second‐order reaction rate constant for the CO₂ reaction with EEA was found to be 8041 m³/(kmol s). The liquid‐side mass transfer coefficient was also estimated, and its value (0.004 cm/s) is in line with those typical of stirred‐cell reactors.     

Novel heterocyclic synthesis and investigation on radiation‐grafted low‐density polyethylene with 2‐N‐vinylpyrrolidone

Radiation‐induced graft polymerization of low‐density polyethylene with N‐vinylpyrrolidone, LDPE‐g‐PNVP, was used as a starting material for the synthesis of polyfunctionally substituted heterocyclic products. Thus, LDPE‐g‐PNVP reacts with ylidenemalononitrile derivatives to give the Michael addition products. In multistep reaction, LDPE‐g‐PNVP reacts with N,N‐dimethylformamide dimethyl acetal (DMFDMA), hydrazine hydrate and malononitrile, respectively, to give a hydropyrrolopyridazine derivative. The latter could also be prepared via the reaction of LDPE‐g‐PNVP with DMFDMA, followed by treating with cyanoacetohydrazide. Also, LDPE‐g‐PNVP reacts with malononitrile to give an adduct product, dimer malononitrile derivative 13. The latter reacts with sulfur element to afford the thiophene derivative. Furthermore, this adduct reacts with hydrazine hydrate to isolate the original starting material, LDPE‐g‐PNVP, and aminopyridine derivative. The resulted films were characterized by infrared (IR) spectroscopy, ¹H nuclear magnetic resonance (¹H‐NMR) mass spectroscopy, elemental analysis, swelling behavior, and electron scanning microscope. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2963–2970, 1999     

N‐doped porous carbons for CO2 capture: Rational choice of N‐containing polymer with high phenyl density as precursor

N‐doped porous carbons (NPCs) are highly promising for CO₂ capture, but their preparation is severely hindered by two factors, namely, the high cost of N‐containing polymer precursors and the low yield of carbon products. Here we report for the first time the fabrication of NPCs through the rational choice of the polymer NUT‐4, with low cost and high phenyl density, as precursor. For the material NPC‐600 obtained from carbonization at 600°C, the yield is as high as 52.1%. The adsorption capacity of CO₂ on NPC‐600 reaches 6.9 mmol/g at 273 K and 1 bar, which is obviously higher than that on the benchmarks, including 13X zeolite (4.1 mmol/g) and activated carbon (2.8 mmol/g), as well as most reported carbon materials. Our results also demonstrate that the present NPCs can be completely regenerated under mild conditions. The abundant microporosity and “CO₂‐philic” (N‐doped) sites are responsible for the adsorption performance. © 2016 American Institute of Chemical Engineers AIChE J, 63: 1648–1658, 2017     

Effect of phenol derivatives on molecular dimensions of poly(N‐vinyl‐2‐pyrrolidone) in aqueous solution

The unperturbed dimensions and thermodynamic parameters of poly(N‐vinyl‐2‐pyrrolidone) (PVP) were studied in aqueous solutions in the presence of certain phenolic cosolutes (phenol, catechol, hydroquinone, resorcinol, and phloroglucinol). The intrinsic viscosities at 25°C and the θ temperature, linear and thermodynamic expansions, and root mean square end to end distances were evaluated for the system that was employed. The sequence was obtained due to the effectiveness of the cosolutes in the order of phloroglucinol > resorcinol > hydroquinone > catechol > phenol. The effects of these cosolutes on the main thermodynamic parameters were reported to be due to the number and position of hydroxyl groups present. The thermodynamic interaction parameter was also evaluated and the enthalpic and entropic contributions were verified. The condition required for the θ temperature to correspond to a Flory interaction parameter of 0.5 was well provided, yielding a θ temperature of almost 0.5 for the system under study. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 473–477, 2002; DOI 10.1002/app.10047     

Effects of inorganic salts on the spectral behavior of poly(N‐vinyl‐2‐pyrrolidone) in aqueous solutions

Electronic spectral behavior of poly(N‐vinyl‐2‐pyrrolidone) (PVP) was determined in aqueous solutions including a variety of inorganic salts (phosphates, mono‐ and dihydrogen phosphates, sulfates, chlorides, nitrates, bisulfites, and persulfates) for several concentrations. The n → π* excitations are shifted to longer wavelengths depending on the nature and the concentration of salt. The resulting dependence of λ_max on the molar concentration can be expressed to show the increasing effect of anionic and cationic species in bathochromic shift. The increasing order of effectiveness of anions in shifting the λ_max is S₂O₈ ⁼ > S₂O₅ ⁼ > PO₄ ³⁻ > HPO₄ ²⁻ > SO₄ ²⁻ > H₂PO₄ ²⁻ > Cl⁻. The order for the cation is as Na⁺ ≈ K⁺ ≈ NH₄ ⁺ in the 0.1–0.6M concentration range and Na⁺ ≈ K⁺ > NH₄ ⁺ in > 0.6M aqueous solutions. The changes observed in λ_max by the salt were correlated with the changes occurring in the structure of water and the polymer–solvent interactions. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1434–1439, 2000     

External Stimuli‐Responsive Characteristics of Ionic Poly[(N,N‐diethylaminoethyl methacrylate)‐co‐(N‐vinyl‐2‐pyrrolidone)] Hydrogels

Summary: Polyelectrolyte hydrogels containing diprotic acid moieties sensitive to ionic strength changes of the swelling medium were synthesized from N,N‐diethylaminoethyl methacrylate (DEAEMA), N‐vinyl‐2‐pyrrolidone (VP) and itaconic acid (IA) by using ammonium persulfate (APS) as a free radical initiator in the presence of the cross‐linker, methylenebisacrylamide (MBAAm). The swelling behavior of the ionic poly[(N,N‐diethylaminoethyl methacrylate)‐co‐(N‐vinyl‐2‐pyrrolidone)] [P(DEAEMA/VP)] hydrogels were investigated in pure water; in NaCI solutions with pH 4 and 9; and in water‐acetone mixtures depending on the IA content in the hydrogel. The average molecular mass between cross‐links ( ) and polymer‐solvent interaction parameter (χ) of the hydrogels were determined from equilibrium swelling values. The pulsatile swelling behavior was also observed in response to solvent changes between the solution in water and in acetone. The equilibrium swelling ratio of these hydrogels was basically unaffected with change in temperature. The swelling variations were explained according to the swelling theory based on the hydrogel chemical structure.

Pulsatile swelling behavior of ionic P(DEAEMA/VP) hydrogels in response to solvent changes between water and acetone at 25 °C.     

Carboxylation of Terminal Alkynes with Carbon Dioxide Catalyzed by Poly(N‐Heterocyclic Carbene)‐Supported Silver Nanoparticles

An N‐heterocyclic carbene (NHC) polymer supported silver nanoparticle catalyst system was developed. The novel nano‐composite catalyst demonstrated very high activity and excellent stability and reusability in the carboxylation of terminal alkynes with carbon dioxide at ambient conditions. The unique N‐heterocyclic carbene polymer and silver nanoparticle composite structure provided a synergistic effect on activation of terminal alkynes and carbon dioxide that contributed to the high catalytic activity. The poly‐NHC‐silver catalyst exhibited excellent substrate generality and tolerance to various functionalities. In addition, the catalyst is stable to air and moisture and can be easily recovered and reused.     

Excess molar enthalpies of the ternary mixtures: Methyl tert‐butyl ether (or di‐isopropyl ether) + n‐octane + 2‐methylpentane at 293.15 K

Microcalorimetric measurements of excess molar enthalpies at 298.15 K are reported for the two ternary mixtures, methyl tert‐butyl ether (MTBE) or di‐isopropyl ether (DIPE) + n‐octane + 2‐methylpentane (2‐MP). The excess enthalpies for DIPE + 2‐MP are also reported. Smooth representations of the ternary enthalpies results are presented and used to construct constant excess molar enthalpy contours on Roozeboom diagrams. It is shown that good estimates of the ternary enthalpies can be obtained from the Liebermann and Fried model, using only the physical properties of the components and their binary mixtures.     

微通道内MEA/MDEA混合溶液吸收CO2的传质特性

研究了T形微通道内N-甲基二乙醇胺（MDEA）和单乙醇胺（MEA）混合水溶液吸收CO₂的传质过程。考察了弹状流型下气液两相流量、MEA和MDEA浓度对液侧传质系数k_L和体积传质系数k_La的影响。液侧传质系数和体积传质系数均会随着MEA浓度的升高而升高。与MEA相比,MDEA浓度的提高对传质影响较小。传质系数会随着液体流量的增大而增大,但气体流量的变化对其影响较小。体积传质系数随液体流量的增大而增大,但随气体流量的增大先增大,之后趋于稳定。考虑到化学反应对传质的强化作用,引入了Hatta数,提出了一个新的体积传质系数预测式,预测效果良好。