Optical and structural properties of CuSbS2 thin films grown by thermal evaporation method

Structural, optical and electrical properties of CuSbS₂ thin films grown by thermal evaporation have been studied relating the effects of substrate heating conditions of these properties. The CuSbS₂ thin films were carried out at substrate temperatures in the temperature range 100-200 °C. The structure and composition were characterized by XRD, SEM and EDX. X-ray diffraction revealed that the films are (111) oriented upon substrate temperature 170 °C and amorphous for the substrate temperatures below 170 °C. No secondary phases are observed for all the films. The optical absorption coefficients and band gaps of the films were estimated by optical transmission and reflection measurements at room temperature. Strong absorption coefficients in the range 10⁵-10⁶ cm^− 1 at 500 nm were found. The direct gaps Eg lie between 0.91-1.89 eV range. It is observed that there is a decrease in optical band gap Eg with increasing the substrate temperature. Resistivity of 0.03-0.96 Ω cm, in dependence on substrate temperature was characterized. The all unheated films exhibit p-type conductivity. The characteristics reported here also offer perspective for CuSbS₂ as an absorber material in solar cells applications.     

Growth and vacuum post-annealing effect on the properties of the new absorber CuSbS2 thin films

Post-growth treatments in vacuum atmosphere were performed on CuSbS₂ films prepared by the single-source thermal evaporation method on glass substrates. The films were annealed in vacuum atmosphere for 2 h in temperature range 130-200 °C. The effect of this thermal treatment on the structural, optical and electrical properties of the films was studied. X-ray diffraction (XRD) patterns indicated that the films exhibited an amorphous structure for annealing temperature below 200 °C and a polycrystalline structure with CuSbS₂ principal phase. For the films annealed at temperatures below 200 °C one direct optical transition in range 1.8-2 eV was found. For the films annealed at 200 °C, two optical direct transitions emerged at 1.3 and 1.79 eV corresponding to the CuSbS₂ and Sb₂S₃ values respectively. The electrical measurements showed a conversion from low resistivities (3.10^− 2-9.10^− 2) Ω cm for the samples annealed at temperatures below 200 °C to relatively high resistivities (2 Ω cm) for the samples annealed at 200 °C. In all cases the samples exhibited p-Ztype conductivity.     

Structural, thermal and optical characterization of TiO2:ZrO2 thin films prepared by sol-gel method

We have studied the structural and optical properties of thin films of TiO₂, doped with 5% ZrO₂ and deposited on glass substrate (by the sol-gel method). The dip-coated thin films have been examined at different annealing temperatures (350 to 450 °C) and for various layer thicknesses (63-286 nm). Refractive index and porosity were calculated from the measured transmittance spectrum. The values of the index of refraction are in the range of 1.62-2.29 and the porosity is in the range of 0.21-0.70. The coefficient of transmission varies from 50 to 90%. In the case of the powder of TiO₂, doped with 5% ZrO₂, and aged for 3 months in ambient temperature, we have noticed the formation of the anatase phase (tetragonal structure with 14.8 nm grains). However, the undoped TiO₂ exhibits an amorphous phase. After heat treatments of thin films, titanium oxide starts to crystallize at the annealing temperature 350 °C. The obtained structures are anatase and brookite. The calculated grain size, depending on the annealing temperature and the layer thickness, is in the range (8.58-20.56 nm).     

Study of optical and structural properties of Cu2ZnSnS4 thin films

Cu₂ZnSnS₄ is a promising semiconductor to be used as absorber in thin film solar cells. In this work, we investigated optical and structural properties of Cu₂ZnSnS₄ thin films grown by sulphurization of metallic precursors deposited on soda lime glass substrates. The crystalline phases were studied by X-ray diffraction measurements showing the presence of only the Cu₂ZnSnS₄ phase. The studied films were copper poor and zinc rich as shown by inductively coupled plasma mass spectroscopy. Scanning electron microscopy revealed a good crystallinity and compactness. An absorption coefficient varying between 3 and 4 × 10⁴cm^− 1 was measured in the energy range between 1.75 and 3.5 eV. The band gap energy was estimated in 1.51 eV. Photoluminescence spectroscopy showed an asymmetric broad band emission. The dependence of this emission on the excitation power and temperature was investigated and compared to the predictions of the donor-acceptor-type transitions and radiative recombinations in the model of potential fluctuations. Experimental evidence was found to ascribe the observed emission to radiative transitions involving tail states created by potential fluctuations.     

Structural instability of Sn-doped In2O3 thin films during thermal annealing at low temperature

We report on observations of structural stability of Sn-doped In₂O₃ (ITO) thin films during thermal annealing at low temperature. The ITO thin films were deposited by radio-frequency magnetron sputtering at room temperature. Transmission electron microscopy analysis revealed that the as-deposited ITO thin films are nanocrystalline. After thermal annealing in a He atmosphere at 250 °C for 30 min, recrystallization, coalescence, and agglomeration of grains were observed. We further found that nanovoids formed in the annealed ITO thin films. The majority of the nanovoids are distributed along the locations of the original grain boundaries. These nanovoids divide the agglomerated larger grains into small coherent domains.     

Photocatalytic properties of porous TiO2/Ag thin films

In this study, nanocrystalline TiO₂/Ag composite thin films were prepared by a sol-gel spin-coating technique. By introducing polystyrene (PS) spheres into the precursor solution, porous TiO₂/Ag thin films were prepared after calcination at a temperature of 500 °C for 4 h. Three different sizes (50, 200, and 400 nm) of PS spheres were used to prepare porous TiO₂ films. The as-prepared TiO₂ and TiO₂/Ag thin films were characterized by X-ray diffractometry (XRD) and by scanning electron microscopy to reveal structural and morphological differences. In addition, the photocatalytic properties of these films were investigated by degrading methylene blue under UV irradiation.When PS spheres of different sizes were introduced after calcination, the as-prepared TiO₂ films exhibited different porous structures. XRD results showed that all TiO₂/Ag films exhibited a major anatase phase. The photodegradation of porous TiO₂ thin films prepared with 200 nm PS spheres and doped with 1 mol% Ag exhibited the best photocatalytic efficiency where ∼ 100% methylene blue was decomposed within 8 h under UV exposure.     

Role of oxygen in enhancing N-type conductivity of CuInS2 thin films

Post-growth treatments in air atmosphere were performed on CuInS₂ films prepared by the single-source thermal evaporation method. Their effect on the structural, optical and electrical properties of the films was studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), optical reflection and transmission and resistance measurements. The films were annealed from 100 to 350 °C in air. The stability of the observed N-type conductivity after annealing depends strongly on the annealing temperature. Indeed it is shown that for annealing temperatures above 200 °C the N-type conductivity is stable. The resistance of the N-CuInS₂ thin films correlates well with the corresponding annealing temperature. The samples after annealing have direct bandgap energies of 1.45-1.50 eV.     

First principles investigation on the structural, mechanical and electronic properties of OsC2

The structural, mechanical and electronic properties of OsC₂ were investigated by use of the density functional theory. Seven structures were considered, i.e., orthorhombic Cmca (No. 12, OsSi₂), Pmmn (No. 59, OsB₂) and Pnnm (No. 58, OsN₂); tetragonal P4₂/mnm (No. 136, OsO₂) and I4/mmm (No. 139, CaC₂); cubic Fm–3m (No. 225, CaF₂) and Pa-3 (No. 205, PtN₂). The results indicate that Cmca in OsSi₂ type structure is energetically the most stable phase among the considered structures. It is also stable mechanically. OsC₂ in Pmmn phase has the largest bulk modulus 319 GPa and shear modulus 194 GPa. The elastic anisotropy is discussed.     

Photoelectrochemical properties of thin Bi2WO6 films

Thin Bi₂WO₆ film prepared from an amorphous heteronuclear complex via dip-coating method is investigated as a visible light-driven photoelectrode material. Photoelectrochemical properties of the resultant film are investigated on the basis of linear sweep voltammetry and current-time curves, and conduction and valence band edges of the film electrode are determined from the photocurrent voltage response. Anodic photocurrent associated with the oxidation of water is obtained under visible light irradiation. Furthermore, the film as a photoanode can degrade rhodamine B (RhB) and methylene blue (MB) in aqueous solution under visible light irradiation slowly. The application of bias potential further improves the photodegradation efficiency of RhB and MB. Based on the analytic result of current-time curve, the stability of the film electrode is confirmed.     

Effects of post-deposition annealing on the structure and optical properties of Y2O3 thin films

Y₂O₃ thin film waveguides were prepared by RF magnetron sputtering. The effects of post-deposition annealing on the structure and optical properties have been investigated. The structural evolution of Y₂O₃ films with annealing temperature was investigated by X-ray diffraction (XRD). Spectroscopic ellipsometry was employed to determine the optical properties of Y₂O₃ films annealed at various temperatures. It was found that with increasing annealing temperature, the refractive index (n) of Y₂O₃ films increases. The optical band gap of Y₂O₃ films shifts to higher energy after higher temperature annealing, which is likely due to the reduction of defects and the change of crystalline structure in Y₂O₃ films.     

Thermo-optic properties of TiO2, Ta2O5 and Al2O3 thin films for integrated optics on silicon

The direct measurement of the thermo-optic coefficients of aluminium oxide, tantalum pentoxide and titanium dioxide thin films is presented. Using ellipsometry on monolithically integrated permutations of the layers of silicon, silicon dioxide and the material under test, allows the direct measurement of the overall thermo-optic coefficient accounting for thermally induced changes in the dielectric permittivity and density of the materials as well as the elasto-optic effect due to the non-matching thermal expansion coefficients of the different materials.     

An investigation of super-hydrophilic properties of TiO2/SnO2 nano composite thin films

A sol-gel dip coating technique was used to fabricate TiO₂/SnO₂ nano composite thin films on soda-lime glass. The solutions of SnO₂ and TiO₂ were mixed with different molar ratios of SnO₂:TiO₂ as 0, 3, 4, 6, 8, 9, 10.5, 13, 15, 19.5, 25 and 28 mol.% then the films were prepared by dip coating of the glasses. The effects of SnO₂ concentration, number of coating cycles and annealing temperature on the hydrophilicity of films were studied using contact angle measurement. The films were characterized by means of scanning electron microscopy, X-ray diffraction and atomic force microscopy measurements. The nano composite thin films fabricated with 8 mol.% of SnO₂, four dip coating cycles and annealing temperature of 500 °C showed super-hydrophilicity.     

Microscale meshes of Ti3O5 nano- and microfibers prepared via annealing of C-doped TiO2 thin films

A new technique to produce microscale Ti₃O₅ nano- and microfiber meshes is proposed. When a 3 wt% carbon-doped TiO₂ film on Si(1 0 0) was annealed at 1000 °C in wet nitrogen (0.8%H₂O), the amorphous TiO₂ phase gave rise to crystalline phases of λ-Ti₃O₅ (75%) and rutile + trace of TiO_2−xC_x (25%). From Raman and FTIR Spectroscopy results, it was concluded that rutile is formed at the inner layer located at the interface between the mesh and the Si that was located away from the surface such that the meshes of nano- and microfibers are predominantly composed of Ti₃O₅ grown from the reaction of rutile with Si to form Ti₃O₅ and SiO₂. On the other hand, it was noteworthy that the microscale mesh of nano- and microfibers showed increased photoluminescence compared with amorphous TiO₂. The PL spectrum which had a broad band in the visible spectrum, fitted as three broad Gaussian distributions centered at 571.6 nm (∼2.2 eV), 623.0 nm (∼2.0 eV) and 661.9 nm (∼1.9 eV).     

Phase transition behaviors and thermal conductivity measurements of nitrogen-doped Sb2Te3 thin films

Crystallization temperature of nitrogen-doped Sb₂Te₃ (ST) thin films increased with increasing nitrogen doping concentration, which indicates that the long-term stability of the metastable amorphous state can be improved by nitrogen doping. The root-mean-square (rms) roughness values of the films showed a significant decrease with nitrogen doping. Thermal conductivity of nitrogen-doped ST thin films was measured using a transient thermoreflectance (TTR) technique. It was found that the thermal conductivity decreased with increasing nitrogen doping concentration and increased with increasing annealing temperature. Nitrogen-doped ST thin films are suitable phase-change materials for low programming power consumption applications of phase-change random access memory (PCRAM).     

Physical properties of electrically conductive Sb-doped SnO2 transparent electrodes by thermal annealing dependent structural changes for photovoltaic applications

We have investigated the optical and electrical characteristics of antimony (Sb)-doped tin oxide (SnO₂) films with modified structures by thermal annealing as a transparent conductive electrode. The structural properties were analyzed from the relative void % by spectroscopic ellipsometry as well as the scanning electron microscopy images and X-ray diffraction patterns. As the annealing temperature was raised, Sb-doped SnO₂ films exhibited a slightly enhanced crystallinity with the increase of the grain size from 17.1 nm at 500 °C to 34.3 nm at 700 °C. Furthermore, the refractive index and extinction coefficient gradually decreased due to the increase in the relative void % within the film during the annealing. The resistivity decreased to 8.2 × 10⁻³ Ω cm at 500 °C, but it increased rapidly at 700 °C. After thermal annealing, the optical transmittance was significantly increased. For photovoltaic applications, the photonic flux density and the figure of merit over the entire solar spectrum were obtained, indicating the highest values of 5.4 × 10¹⁴ cm⁻² s⁻¹ nm⁻¹ at 1.85 eV after annealing at 700 °C and 340.1 μA cm⁻² Ω⁻¹ at 500 °C, respectively.     

Effect of intentional Na-incorporation on the structural, optical and electrical properties of CuInS2:Na thin films for solar energy conversion

Na-doped CuInS₂ material is obtained by the incorporation of the sodium of an atomic percentage in amounts of 0, 0.1, 0.5, 1, 2 and 3% with a stoechiometric mixture of the elements copper, indium and sulfur taken in the stoechiometric proportions. We have investigated in this work the effect of intentional Na-incorporation on the structural, optical and electrical properties of CuInS₂:Na-doped thin films grown by the single source thermal evaporation method. In the resulting Bridgman-grown ingots brittleness were increased with increased Na and measured hot point probe changed sign from p- to n-type in stoechiometric ingots above 0.5 at.%. The samples having a low Na atomic percentage exhibit better crystallinity that shows the effect of the sodium for the larger percentage to degrade the crystallinity of layers (atomic percentage greater than 2 at.%). The film conductivity was strongly affected by Na-doping, which increased from 10^− 6 to 10^− 3 S/cm by increasing [Na]/[CuInS₂] ratio from 0.1 to 3 at.%. Indeed for an atomic percentage Na of 1% we obtained the biggest thickness (1 μm) corresponds to the lowest refractive index value (2.08).     

The effect of Au and Pt nanoclusters on the structural and hydrogen sensing properties of SnO2 thin films

Au and Pt nanoparticle modified SnO₂ thin films were prepared by the sol-gel method on glass substrates targeting sensing applications. Structural and morphological properties of these films were studied using X-ray Diffraction and Scanning Electron Microscopy. It was proved that the films crystallized in tetragonal rutile SnO₂ crystalline structure. Scanning Electron Microscopy observations showed that the metallic clusters' dimensions and geometry depend on the kind of the metal (Au or Pt) while SnO₂ films surface remains almost the same: nanostructured granular very smooth. Optical properties of the films were studied using UV-visible spectroscopy. The modified SnO₂ films were tested as hydrogen sensors. The response of SnO₂, SnO₂-Au and SnO₂-Pt thin films against hydrogen was investigated at different operating temperatures and for different gas concentrations. The addition of metal nanoparticles was found to decrease the detection limit and the operating temperature (from 180 °C to 85 °C), while increasing the sensing response signal.     

A study of textured non-stoichiometric MoTe2 thin films used as substrates for textured stoichiometric MoS2 thin films

Textured MoTe₂ films have been prepared by sequential evaporation of the constituents followed by annealing under a tellurium pressure. The films are systematically textured with the c-axis of the crystallites perpendicular to the plane of substrate, however, the film composition is difficult to control and even after process optimization the films are tellurium deficient. This is thought to be caused by the electro negativity difference of the constituents.The textured MoTe₂ films have been used as substrates on which to grow MoS₂ films by annealing under a pressure of sulfur that allows textured MoS₂ films to be grown with good crystalline properties. The presence of sulfur at the surface and annealing under dynamic vacuum is important for this process and moreover, suppresses the superficial oxidation of the Mo and Te constituents.     

Epitaxial and polycrystalline CuInS2 thin films: A comparison of opto-electronic properties

Epitaxial and polycrystalline thin CuInS₂ (CIS) layers were grown by means of molecular beam epitaxy (MBE) on single crystalline silicon substrates of 4 inch diameter. Photoluminescence (PL) studies were performed to investigate the opto-electronic properties of these layers. For the epitaxial CIS, low-energy-hydrogen implantation leads to the passivation of deep defects and several donor-acceptor (DA) pair recombinations (from 1.034 eV to 1.439 eV) and two free-to-bound (FB) transitions (at 1.436 eV and 1.485 eV) become observable at low temperatures (5 to 100 K). Excitonic luminescence is completely absent for all investigated epitaxial CIS layers. This contrasts sharply with the PL of the polycrystalline films which is dominated by excitonic luminescence (1.527 eV). Also a donor-to-valence band transition at 1.465 eV (BF-1) and one donor-acceptor recombination at 1.435 eV (DA-1) were observed, while luminescence from deep levels is not present at all. Based on these data, a refined defect model for CuInS₂ with two donor and two acceptor states is presented. Under comparable growth conditions, the electronic quality of polycrystalline CIS is superior to epitaxially grown material.     

Optical constants of Zn-doped CuInS2 thin films

Optical properties of Zn-doped CuInS₂ thin films grown by double source thermal evaporation method have been studied. The amount of the Zn source was determined to be 0%-4% molecular weight compared with CuInS₂ source. After that, samples were annealed in vacuum at the temperature of 450 °C in quartz tube. The optical constants of the deposited films were obtained from the analysis of the experimental recorded transmission and reflexion spectral data over the wavelength range 300-1800 nm. It is observed that there is an increase in optical band gap with increasing Zn % molecular weight. It has been found that the refractive index and extinction coefficient are dependent on Zn incorporation. The complex dielectric constants of Zn-doped CuInS₂ films have been calculated in the investigated wavelength range. It was found that the refractive index dispersion data obeyed the single oscillator of the Wemple-DiDomenico model, from which the dispersion parameters and the high-frequency dielectric constant were determined. The electric free carrier susceptibility and the carrier concentration on the effective mass ratio were estimated according to the model of Spitzer and Fan.