In Situ Reaction Synthesis of Silicon Carbide–Boron Nitride Composite from Silicon Nitride–Boron Oxide–Carbon

This work proposes a new approach, based on the reaction Si₃N₄+ 2B₂O₃+ 9C → 3SiC + 4BN + 6CO, to synthesize an SiC–BN composite. The composite was prepared by reactive hot pressing (RHP), at 2000°C for 60 min at 30 MPa under an argon atmosphere, following a 60 min hold at 1700°C without applied pressure before reaching the RHP temperature. TG-DTA results showed that a nitrogen atmosphere inhibited denitrification somewhat and retarded the reaction rate. The chemical composition of the obtained material was consistent with theoretical values. FE-SEM observation showed that in situ -formed SiC and BN phases were of spherical morphology with very fine particle size of ∼100 nm.     

In Situ Reaction Synthesis of Silicon Carbide–Boron Nitride Composites

SiC–BN composites were prepared via the proposed in situ reaction, which used Si₃N₄, B₄C, and carbon as reactants. Adding SiC powder to the reactants controlled the BN content in the composite. For comparison, SiC–BN composites with the same phase compositions were produced via conventional processing. The in situ process was advantageous for obtaining better composites with fine grain size and homogeneous microstructures. The in situ composite that had a BN content of 53.71 vol% exhibited considerably high strength (342 MPa) and a very low elastic modulus (107 GPa). The SiC–25-vol%-BN in situ composite had a peak strength of 588 MPa, which was 95% of that of monolithic SiC; however, the elastic modulus was as low as half that of monolithic SiC. These in situ SiC–BN composites can be expected to have excellent thermal shock resistance and mechanical strain tolerance.     

Hot Isostatic Pressing of Silicon Nitride with Boron Nitride, Boron Carbide, and Carbon Additions

Si₃ N₄ test bars containing additions of BN, B₄C, and C, were hot isostatically pressed in Ta cladding at 1900° and 2050°C to 98.9% to 99.5% theoretical density. Room-temperature strength data on specimens containing 2 wt% BN and 0.5 wt% C were comparable to data obtained for Si₃ N₄ sintered with Y₂O₃, Y₂O₃ and Al₂O₃, or ZrO₂. The 1370°C strengths were less than those obtained for additions of Y₂O₃ or ZrO₂ but greater than those obtained from a combination of Y₂O₃ and Al₂O₃. Scanning electron microscope fractography indicated that, as with other types of Si₃N₄, roomtemperature strength was controlled by processing flaws. The decrease in strength at 1370°C was typical of Si₃N₄ having an amorphous grainboundary phase. The primary advantage of non-oxide additions appears to be in facilitating specimen removal from the Ta cladding.     

Molecular Dynamics Study of Atomic Structure and Diffusion Behavior in Amorphous Silicon Nitride Containing Boron

We have performed molecular dynamics simulations of amorphous Si₃N₄ containing boron (Si-B-N). We have examined short-range atomic arrangements and self-diffusion constants of amorphous Si-B-N systems with various boron contents. Our simulations show that boron atoms are threefold coordinated by nitrogen atoms and that nitrogen atoms are bonded to both silicon and boron atoms in the amorphous network of Si-B-N. Also, the self-diffusion constant of nitrogen in Si-B-N is much decreased compared with that in amorphous Si₃N₄. This suggests that boron is important in decreasing the mobility of atoms in amorphous Si-B-N, which may explain the improved thermal stability of amorphous Si-B-N relative to amorphous Si₃N₄ observed experimentally.     

In Situ Synthesis and Microstructures of Tungsten Carbide-Nanoparticle-Reinforced Silicon Nitride-Matrix Composites

A W₂C-nanoparticle-reinforced Si₃N₄-matrix composite was fabricated by sintering porous Si₃N₄ that had been infiltrated with a tungsten solution. During the sintering procedure, nanometer-sized W₂C particles grew in situ from the reaction between the tungsten and carbon sources considered to originate mainly from residual binder. The W₂C particles resided in the grain-boundary junctions of the Si₃N₄, had an average diameter of ∼60 nm, and were polyhedral in shape. Because the residual carbon, which normally would obstruct sintering, reacted with the tungsten to form W₂C particles in the composite, the sinterability of the Si₃N₄ was improved, and a W₂C–Si₃N₄ composite with almost full density was obtained. The flexural strength of the W₂C–Si₃N₄ composite was 1212 MPa, ∼34% higher than that of standard sintered Si₃N₄.     

Machinability of Silicon Nitride/Boron Nitride Nanocomposites

The machinability and deformation mechanism of Si₃N₄/BN nanocomposites were investigated in the present work. The fracture strength of Si₃N₄/BN microcomposites remarkably decreased with increased hexagonal graphitic boron nitride ( h -BN) content, although machinability was somewhat improved. However, the nanocomposites fabricated using the chemical method simultaneously had high fracture strength and good machinability. Hertzian contact tests were performed to clarify the deformation behavior by mechanical shock. As a result of this test, the damage of the monolithic Si₃N₄ and Si₃N₄/BN microcomposites indicated a classical Hertzian cone fracture and many large cracks, whereas the damage observed in the nanocomposites appeared to be quasi-plastic deformation.     

Preparation of Ultrafine Silicon Nitride, and Silicon Nitride and Silicon Carbide Mixed Powders in a Hybrid Plasma

Ultrafine Si₃N₄ and Si₃N₄+ SiC mixed powders were synthesized through thermal plasma chemical vapor deposition (CVD) using a hybrid plasma which was characterized by the superposition of a radio-frequency plasma and an arc jet. The reactant, SiCl₄, was injected into an arc jet and completely decomposed in a hybrid plasma, and the second reactant, CH₄ and/or NH₃, was injected into the tail flame through multistage ring slits. In the case of ultrafine Si₃N₄ powder synthesis, reaction effieciency increased significantly by multistage injection compared to single-stage injection. The most striking result is that amorphous Si₃N₄ with a nitrogen content of about 37 wt% and a particle size of 10 to 30 nm could be prepared successfully even at the theoretical NH₃/SiCl₄ molar ratio of ∼ 1.33, although the crystallinity depended on the NH₃/SiCl₄ molar ratio and the injection method. For the preparation of Si₃N₄+ SiC mixed powders, the N/C composition ratio and particle size could be controlled not only by regulating the flow rate of the NH₃ and CH₄ reactant gases and the H₂ quenching gas, but also by adjusting the reaction space. The results of this study provide sufficient evidence to suggest that multistage injection is very effective for regulating the condensation process of fine particles in a plasma tail flame.     

Control of Composition and Structure in Laminated Silicon Nitride/Boron Nitride Composites

Based on a biomimetic design, Si₃N₄/BN composites with laminated structures have been prepared and investigated through composition control and structure design. To further improve the mechanical properties of the composites, Si₃N₄ matrix layers were reinforced by SiC whiskers and BN separating layers were modified by adding Si₃N₄ or Al₂O₃. The results showed that the addition of SiC whiskers in the Si₃N₄ matrix layers could greatly improve the apparent fracture toughness (reaching 28.1 MPa·m^1/2), at the same time keeping the higher bending strength (reaching 651.5 MPa) of the composites. Additions of 50 wt% Al₂O₃ or 10 wt% Si₃N₄ to BN interfacial layers had a beneficial effect on the strength and toughness of the laminated Si₃N₄/BN composites. Through observation of microstructure by SEM, multilevel toughening mechanisms contributing to high toughness of the laminated Si₃N₄/BN composites were present as the first-level toughening mechanisms from BN interfacial layers as crack deflection, bifurcation, and pull-out of matrix sheets, and the secondary toughening mechanism from whiskers in matrix layers.     

Fabrication of Low-Shrinkage, Porous Silicon Nitride Ceramics by Addition of a Small Amount of Carbon

Successful net-shape sintering offers a significant advantage for producing large or complicated products. Porous Si₃N₄ ceramics with very low shrinkage were developed, in the present investigation, by the addition of a small amount of carbon. Carbon powders (1–5 vol%) of two types, with different mean particle sizes (13 nm and 5 μm), were added to α-Si₃N₄−5 wt% Y₂O₃ powders. SiC nanoparticles formed through reaction of the added carbon with SiO₂ on the Si₃N₄ surface or with the Si₃N₄ particles themselves. Such reaction-formed SiC nanoparticles apparently had an effective reinforcing effect, as in nanocomposites. Sintered Si₃N₄ porous ceramics with a high porosity of 50%–60%, a very small linear shrinkage of ∼2%–3%, and a strength of ∼100 MPa were obtained.     

Synthesis of Silicon Carbide–Silicon Nitride Composite Ultrafine Particles Using a Carbon Dioxide Laser

The synthesis and the structure of silicon carbide-silicon nitride (SiC─Si₃N₄) composite ultrafine particles have been studied. SiC─Si₃N₄ composite ultrafine particles were prepared by irradiating a SiH₄, C₂H₄, and NH₃ gas mixture with a CO₂ laser at atmospheric pressure. The composition of composite powders changed with the reactant gas flow rate. The carbon and nitrogen content of the powder could be controlled in a wide range from 0 to 30 wt%. The composite powder, which contained 25.3 wt%. carbon and 5.8 wt% nitrogen, had a (β-SiC structure. As the nitrogen con- tent increased, SiC decreased and amorphous phase, Si₃N₄, Si appeared. The results of XPS and lattice constant measurements suggested that Si, C, and N atoms were intimately mixed in the composite particles.     

Fabrication and Microstructure of Silicon Nitride/Boron Nitride Nanocomposites

A chemical process for fabrication of Si₃N₄/BN nanocomposite was devised to improve the mechanical properties. Si₃N₄/BN nanocomposites containing 0 to 30 vol% hexagonal BN ( h -BN) were successfully fabricated by hot-pressing α-Si₃N₄ powders, on which turbostratic BN ( t -BN) with a disordered layer structure was partly coated. The t -BN coating on α-Si₃N₄ particles was prepared by reducing and heating α-Si₃N₄ particles covered with a mixture of boric acid and urea. TEM observations of this nanocomposite revealed that the nanosized hexagonal BN ( h -BN) particles were homogeneously dispersed within Si₃N₄ grains as well as at grain boundaries. As expected from the rules of composites, Young's modulus of both micro- and nanocomposites decreased with an increase in h -BN content, while the fracture strength of the nanocomposites prepared in this work was significantly improved, compared with the conventional microcomposites.     

Reaction-Bonded and Superplastically Sinter-Forged Silicon Nitride–Silicon Carbide Nanocomposites

Silicon nitride–silicon carbide (Si₃N₄–SiC) nanocomposites were fabricated by a process involving reaction bonding followed by superplastic sinter-forging. The nanocomposites exhibited an anisotropic microstructure, in which rod-shaped, micrometer-sized Si₃N₄ grains tended to align with their long axes along the material-flow direction. SiC particles, typically measuring several hundred nanometers, were located at the Si₃N₄ grain boundaries, and nanosized particles were dispersed inside the Si₃N₄ grains. A high bending strength of 1246 ± 119 MPa, as well as a high fracture toughness of 8.2 ± 0.9 MPa·m^1/2, was achieved when a stress was applied along the grain-alignment direction.     

Phase and Property Studies of Boron Carbide–Boron Nitride Composites

Boron carbide–boron nitride particulate composites were fabricated by vacuum hot-pressing. Near-theoretical densities of B₄C were obtained, but percent theoretical densities decreased with increasing amounts of BN. The grain size of B₄C and BN was not affected by composition, but the amount of twinning in B₄C decreased with increasing BN content. No third phase was found at the B₄C–BN interface by analytical STEM analysis. Lattice parameter measurements indicated slight solubility of B₄C in BN, but no solubility of BN in B₄C for samples hot-pressed at 2250°C. Room-temperature flexural strength measurements revealed a sharply decreasing strength with increasing BN content up to 40% BN, and then relatively constant values with greater amounts of BN.     

Texture Development in Silicon Nitride–Silicon Oxynitride In Situ Composites via Superplastic Deformation

Silicon nitride–silicon oxynitride (Si₃N₄–Si₂N₂O) in situ composites have been fabricated via either the annealing or the superplastic deformation of sintered Si₃N₄ that has been doped with a silica-containing additive. In this study, quantitative texture measurements, including pole figures and X-ray diffraction patterns, are used in conjunction with scanning electron microscopy and transmission electron microscopy techniques to examine the degree of preferred orientation and texture-development mechanisms in these materials. The results indicate that (i) only superplastic deformation can produce strong textures in the β-Si₃N₄ matrix, as well as Si₂N₂O grains that are formed in situ ; (ii) texture development in the β-Si₃N₄ matrix mainly results from grain rotation via grain-boundary sliding; and (iii) for Si₂N₂O, a very strong strain-dependent texture occurs in two stages, namely, preferred nucleation and anisotropic grain growth.     

Superplastic Deformation in Silicon Nitride–Silicon Oxynitride In Situ Composites

Starting with a mixture of ultrafine β-Si₃N₄ and a SiO₂-containing additive, a superplastic Si₃N₄-based composite was developed, using the concept of a transient liquid phase. Significant deformation-induced phase and microstructure evolutions occurred in the nonequilibrium, fine-grained Si₃N₄ material, which led to the in situ development of a Si₃N₄–22-vol%-Si₂N₂O composite and strong texture formation. The unusual ductility of the composites with elongated Si₂N₂O grains was attributed to the fine-grained microstructure, the presence of a transient liquid phase, and the alignment of the elongated Si₂N₂O grains. The mechanical properties of the resultant composite were enhanced rather than impaired by superplastic deformation and subsequent heat treatment; the resultant composite exhibited both high strength (957 MPa) and high fracture toughness (4.8 MPa·m^1/2).     

Layered Silicon Nitride-Based Composites with Discontinuous Boron Nitride Interlayers

The influence of a strong/weak interface ratio on the mechanical properties of Si₃N₄/BN-based layered composites was studied. The ratio was controlled by the number of BN spots between the adjacent Si₃N₄ layers. By increasing the BN interface area from 0% to 72%, fracture toughness increased from 7.7 to 10.9 MPa·m^1/2, and bending strength decreased from 1275 to 982 MPa. Fracture toughness was improved from 8.6 to 10.1 MPa·m^1/2 by additional heat treatment of samples containing 2 vol%β-Si₃N₄ seed particles. The bending strength of samples with 35% weak BN interfaces, measured perpendicular and parallel to layer alignment, was 1260 and 1240 MPa, respectively. This confirmed the two-directional isotropy of layered samples.     

Silicon Nitride Joining Using Silica and Yttria Ceramic Interlayers

Dense hot-pressed β-Si₃N₄ blocks were joined using both SiO₂ and SiO₂-Y₂O₃ powder slurries as bonding interlayers. The assembled specimens (Si₃N₄/interlayer/Si₃N₄) were heated in a flowing N₂ atmosphere in the temperature range of 1500°–1650°C. The joining interlayer was clearly distinguished from the Si₃N₄ bulk. The microstructure and the reaction products found in the bonding interlayer were very different in both compositions. Reactions occurring between the Si₃N₄ and the ceramic joining compositions have been explained based on existing diagrams of the YN–Si₃N₄-Y₂O₃-SiO₂ system.     

Mechanical Properties of Three-Layered Monolithic Silicon Nitride–Fibrous Silicon Nitride/Boron Nitride Monolith

A three-layered composite, composed of a strong outer layer (monolithic S₃N₄) and a tough inner layer (fibrous Si₃N₄/BN monolith), was fabricated by hot-pressing. For the inner layer, a Si₃N₄–polymer fiber made by extrusion was coated by dipping it into a 20 wt% BN-containing slurry. The three-layered composite exhibited excellent mechanical properties, including high strength, work of fracture, and crack resistance, because of the combination of a strong outer layer and a tough inner layer. In other words, the strong outer layer withheld the applied stress, while the tough inner layer promoted crack interactions through the weak BN cell boundaries. Also, the residual thermal stress on the surface due to the anisotropy in the coefficient of thermal expansion of BN affected a median/radial crack generation after indentation.     

Influence of Additives on Slag Resistance of Al2O3-SiO2-SiC-C Refractory Bond Phases under Reducing Atmosphere

The microstructures of Al₂O₃–SiO₂–SiC–C refractory matrices with aluminum, silicon, Si₃N₄, BN, B₂O₃, and B₄C additives are characterized before and after a crucible slag test, and the phases present are compared to those expected at thermodynamic equilibrium. The carbon content dominates the resistance to CaO–MgO–Al₂O₃–SiO₂ slag penetration, while the viscosity of liquid phases present has a significant influence when the matrix carbon contents are similar. Silicon and Si₃N₄ additives reduce slag penetration resistance because of indirect oxidation of carbon to form SiC. B₄C, in particular, and B₂O₃ also reduce slag penetration resistance because of formation of a more fluid boron-containing liquid, while aluminum and BN addition have no significant effect. Carbon and BN hardly react with the slag, while SiC partially reacts with it, leading to deposition of carbon as a dense layer. Corundum present in the refractories also readily dissolves in the slag. Microstructurally, slag penetration resistance is associated with the dense carbon layer located at the slag-refractory interface.     

Seamless Joining of Silicon Nitride Ceramics

High-strength joining of Si₃N₄ ceramics has been achieved by developing a process that effectively eliminates the seam, and may allow for fabrication of large or complex silicon nitride bodies. This approach to joining is based on the concept that when sintering aids are effective in bonding individual grains, they could be equally effective in joining bulk pieces of Si₃N₄. Optimization of the process led to Si₃N₄/Si₃N₄ joints with room-temperature bend strengths as high as 950 MPa, corresponding to more than 90% of the bulk strength of the Si₃N₄. At elevated temperatures of 1000° and 1200°C joint strengths of 666 and 330 MPa, respectively, were obtained, which are the highest values reported to date for these temperatures. These bend strengths are also more that 90% of the strength of bulk Si₃N₄ measured at these temperatures.