全息干涉法在液相扩散系数测定中的应用

液相扩散系数是研究气－液、液－液和液－固传质的重要物性参数，由于理论预测和各种估算方法还不成熟和完善，因此其实验测定方法尤其受到人们的关注和重视，激光全息干涉法是一种新型的现代光学测量方法，本文着重介绍全息干涉法用于液相扩散系数的测定和研究进展。     

L-抗坏血酸水溶液扩散系数的测定

为进一步补充药类物质水溶液扩散系数的实验数据和研究相关理论模型的实用性,今制备了金属膜池,用氯化钾溶液标定了膜池常数,并用已有可靠扩散系数值的蔗糖水溶液验证了装置的可靠性.测定了298.15K到328.15K不同温度下L-抗坏血酸在水溶液中可溶解范围内不同浓度下的扩散系数.结果表明在相同温度下,L-抗坏血酸水溶液的扩散系数随着浓度的增加而减小;在同一浓度下,随着温度的升高而增加.另一方面Gordon在扩散模型基础上,关联得到一个有温度项的扩散系数半经验模型,计算结果与实验值吻合很好. 同时用精密密度计和粘度计测定了体系相应的密度和粘度,并与浓度进行了关联.     

葡萄糖水溶液扩散系数的测定与关联

液相扩散系数在化工数据中起着非常重要的作用,由于液体结构及扩散本身的复杂性,至今还没有一个合理的理论模型来预测液相扩散系数,有必要从实验和理论上对不同的体系进行研究.制备了金属膜池,用氯化钾溶液标定了膜池常数,并用已有可靠文献值的蔗糖水溶液验证了装置的可靠性.测定了298.15～328.15 K不同温度下葡萄糖水溶液的积分扩散系数,考察了温度对扩散系数的影响.在实验数据的基础上,提出一个有温度关联项的半经验模型,关联和计算了本实验的数据,结果与实验值吻合很好.     

θ网环形填料的传质性能测定

θ网环形填料是一种实验室常见的精密填料,广泛应用于精细化工品的分离,然而目前对于该种填料的传质性能研究有所欠缺,造成了应用上的盲目性,针对此种问题,用CO_2-H_2O体系测定了5 mm×5 mm的θ网环形填料的传质性能,并分析了液相黏度和表面张力对填料传质性能的影响,通过数据拟合,得出θ网环形填料的液相体积传质系数与各主要的准数之间的关联式,指导实际应用。     

微溶气体在液相中分子扩散系数的测定

一、引言微溶气体在液相中的分子扩散系数的测定在理论上和工程上都很有价值。由于我们对液相的研究仍处在探索阶段,对各种液相的理论和模型,分子扩散系数可以提供检验依据。在进行工程气液传质设备的设计时,气体在液相中的扩散系数是重要的参考数据。     

强制气流作用下溶液蒸发过程的传质规律

针对强制气流作用下溶液的蒸发过程,在分析气液相间力学特性的基础上,根据Levich涡流衰减理论和边界层理论,将气流流动状态与相间传质结合,研究了湍流气流横掠液面过程中气液相间的传质变化规律,分析了雷诺数、气流流道结构及普朗特混合长度对传质的影响,得到了气液相间的湍流质扩散系数的变化规律,湍流气流横掠液面条件下的对流传质准则数Sh=0.221Sc1/3Rex1/2. 结果表明,湍流扩散系数、传质系数与气流的流动状态密切相关,气流流道结构对气液相间的传质有重要影响.     

气液固三相循环流化床气液传质行为

<正>气液固三相流化床反应器在石油化工、湿法冶金、环境工程和煤的液化等工业领域得到了广泛应用,其基础研究也取得了很大进展.但是,传统三相床主要应用于低液速(U_L<     

反相气相色谱法测定小分子溶剂在聚乙烯粒子中的无限稀释扩散系数

基于经典线性非平衡色谱过程的矩分析理论,用反相气相色谱法测定了323.15～358.15 K温度范围内二氯甲烷、三氯甲烷、四氯甲烷3种不同相对分子量的同系物小分子及正己烷在聚乙烯粒子中的无限稀释扩散系数。采用聚合物粒子直接填充的色谱柱,考察了温度、同系物小分子分子量及聚乙烯结晶度对扩散系数的影响。实验结果表明,对同一种小分子溶剂/聚乙烯体系,扩散系数均随温度升高而增大。不同相对分子量的同系物小分子在同一种聚乙烯中扩散系数随分子量增加而减小,聚乙烯结晶度增加也会导致扩散系数减小。采用文献中所报道的Krevelen扩散系数预测模型的计算值与实验测量值较为吻合,表明本文所采用的以聚合物粒子直接填充色谱柱的反相气相色谱扩散分析具有一定的可靠性。     

EPA和DHA在超临界流体色谱柱中的传质动力学

用超临界流体色谱 (SFC)法研究了EPA和DHA在C18上的吸附和传质性能 .建立了色谱动力学模型并获得了模型参数 ,较好地拟合了实验流出曲线 .结果表明吸附平衡、轴向弥散、流体相传质和颗粒内有效扩散都是影响SFC分离EPA和DHA的重要因素     

CH4和CO2在活性炭微球内扩散系数的测定

活性炭微球是一种储存及净化天然气的新型碳材料.采用高精度的重力分析仪(IGA-003, HIDEN)对天然气主要成分CH₄和CO₂杂质在活性炭微球材料内的扩散性质进行了研究.运用Fick扩散模型关联得到了CH₄及CO₂在活性炭微球内的扩散系数.研究结果表明,CH₄与CO₂在活性炭微球内的扩散属于晶体扩散,二者的扩散系数处于10^-13m²·s^-1数量级上.同时,CH₄与CO₂在介孔活性炭微球内的扩散速率均随着温度的增加而增加,随着体系平衡压力的增加而减小,而且CH₄的扩散速率要略大于CO₂的扩散速率.研究结果可用于活性炭微球吸附剂应用中传质性质的计算.     

Axial Mixing and Mass Transfer Performance of an Annular Pulsed Disc-and-Doughnut Column

The annular pulsed disc-and-doughnut column (APDDC) is an important type of extraction equipment in the PUREX process, which has been used in several commercial reprocessing plants. As there are few mass transfer experimental results reported in the literature, the axial mixing and mass transfer performance of an APDDC was studied for both extraction and stripping processes in the present work. Two parameters in the axial dispersion model (ADM), namely, the axial dispersion coefficient of the continuous phase and the number of mass transfer units, were regressed by correlating ADM with experimental concentration profiles. The influence of flow rate and pulsation intensity on these parameters was also investigated. Models developed for the PDDC were tested for correlation with APDDC experimental data and suitable models and conditions were determined. The height of a mass transfer unit was also calculated, which highlights the impact of axial mixing on mass transfer performance. Moreover, the influence of internal wettability on mass transfer performance was discussed.     

鼓泡床反应器内流动与传质行为的研究进展

总结了有关浆态鼓泡床反应器内流动、混合用气液传质特性的研究成果,详细地介绍了鼓泡床反应器内气含率、液速、液体轴向扩散系数、传质系数的测量方法,阐述了鼓泡床反应器性能的主要影响因素,如系统压力、温度、气体表观气速、液体性质及固含率等对流动、液相混合和传质特性的影响,并对鼓泡床反应器的应用前景进行了详述.     

色谱模型中轴向扩散项的理论研究

用矢量方法讨论了色谱模型中的轴向扩散项,指出轴向扩散项是扩散通量以分量的形式在主体流动能量上的贡献。解释了理论塔板数和色谱柱柱长之间的关系;引入特征参数矢量角θ,并利用当量塔板高度关系式对θ进行了关联。回归分析表明,θ可以用流动相雷诺数Ｒｅ和无因次保留时间τ很好地进行关联,关联结果为：θ＝０．４６６６ι＋４．３５９９Ｒｅ－１．７０６６。对脉冲进样时乙酸乙酯、苯和吡喧的当量塔板高度的预测表明,参数θ     

聚并-分散脉冲筛板萃取塔的传质与轴向混合特性

A new configuration of coalescence-dispersed pulsed-sieve-plate extraction column (CDPSEC) was developed, and the mass transfer and axial mixing characteristics were evaluated with the two-point dynamic method.The influence of operation conditions was discussed with experimental results, showing that the mass transfer performance of CDPSEC mainly depends on the energy input and the holdup of dispersed phase. Higher energy input results in higher holdhp of the dispersed phase, the axial mixing of the continuous phase is suppressed, and the true height of mass transfer unit decreases markedly. On the other hand, higher energy input leads to more serious forward mixing of the dispersed phase, so the energy input should be limited. Accordingly the operation conditions were divided into two regions, and empirical correlations for predicting the mass transfer and axial mixing characteristics in different regions with a satisfactory accuracy were suggested.     

Mass Transfer and Axial Mixing Characteristics in a Coalescence-Dispersion Pulsed-Sieve-Plate Extraction Column

A new configuration of coalescence-dispersed pulsed-sieve-plate extraction column (CDPSEC) was developed, and the mass transfer and axial mixing characteristics were evaluated with the two-point dynamic method. The influence of operation conditions was discussed with experimental results, showing that the mass transfer performance of CDPSEC mainly depends on the energy input and the holdup of dispersed phase. Higher energy input results in higher holdup of the dispersed phase, the axial mixing of the continuous phase is suppressed, and the true height of mass transfer unit decreases markedly. On the other hand, higher energy input leads to more serious forward mixing of the dispersed phase, so the energy input should be limited. Accordingly the operation conditions were divided into two regions, and empirical correlations for predicting the mass transfer and axial mixing characteristics in different regions with a satisfactory accuracy were suggested.     

一种用于气液间传质的新型轴流式叶轮

一种用于气液间传质的新型轴流式叶轮黄庆民林齐浩李启恩（华南理工大学化学工程研究所，广州５１０６４１）关键词气液传质轴流式叶轮１前言在液体搅拌器中，轴流式叶轮由于功耗较小且泵吸量较大而被广泛采用。在气液两相搅拌器中，由于轴流式叶轮有气泛问题，一般均采...     

乳状液膜分离Zn^2＋的界面传质阻力及传质模型

用Ｌｗｅｉｓ恒界面传质池对乳状液膜分离Ｚｎ＾２＋的传质阻力进行实验研究，结果表明由于表面活性剂单分子层的形成，使界面传质阻力占整个传质阻力的８５％。在此基础上所建立的既考虑界面传质阻力又考虑膜破碎的液膜传质模型能使用理论计算值与实验测定值符合较好。     

浆态鼓泡床反应器气液传质特性的研究进展

本文总结了有关浆态鼓泡床反应器气液传质特性的研究成果。详细地阐述了主要影响因素如系统压力、温度、气体表观气速、液体性质,固体浓度及其物性等对传质特性的影响,并对浆态鼓泡床传质模型进行了归纳介绍,最后对反应器未来的研究方向进行了预测。     

Measurement of Mass Transfer Coefficients and Their Modelling of Continuous Counter-Current Aqueous Two-Phase System in a Packed Extraction Column

Overall dispersed side volumetric mare transfer coeffcieats for protein and amino acids were measured in continuous countercurreat PEG4000/KHP aqueous two-phase systems in a 57 mm I.D. packed extraction column. A model for overall dispersed side volumetric mass transfer coefficients was derived by describing the motion of the drops based upon Navier-Stokes equation combined with the relationship between mass transfer coefficients and the drop velocity. The model provides good predictions and can be successfully used in aqueous two-phase extraction. The awrage relative deviation between calculated values and experimental date ranges from 8% to 14%.