Effect of different volume fractions of ammonia on the combustion and emission characteristics of the hydrogen-fueled engine

Hydrogen internal combustion engines (ICE) will play an important role in reducing carbon emissions, but low power density and abnormal combustion problems are the main obstacles restricting the promotion of hydrogen ICE. Ammonia is a low-reactivity renewable fuel. The purpose of this study is to study the effect of different ammonia-added volume fractions on hydrogen ICE. In this experimental study, the combustion and emission characteristics of an engine fueled by a hydrogen/ammonia mixture were evaluated at part-load operating conditions. The experiment was carried out on a modified engine, the engine speed was 1300 rpm, the absolute pressure of the manifold was 61 kPa, and the volume fraction of ammonia added was 5.2%, 7.96%, and 10.68%, respectively. The test results show that the addition of ammonia changes the combustion characteristics of hydrogen. As the volume fraction of ammonia added increases, the flame development period and flame propagation period are both prolonged, and the peak heat release rate decreases. The addition of ammonia increases the power of the engine and reduces the indicated thermal efficiency. At the ignition timing of the maximum braking torque, as the volume fraction of ammonia added increases, the indicated mean effective pressure and indicated thermal efficiency increase. Adding ammonia volume fraction has little effect on Nitrogen oxides (NOx) emissions, and NOx emissions gradually increase with the delay of ignition timing.     

Laminar burning characteristics of ammonia/hydrogen/air mixtures with laser ignition

Ammonia, as a zero-carbon fuel, is drawing more and more attention. The major challenge of using ammonia as a fuel for the combustion engines lies in its low chemical reactivity, and therefore more fundamental researches on the combustion characteristics of ammonia are required to explore effective ways to burn ammonia in engines. In this study, the laminar burning characteristics of the premixed ammonia/hydrogen/air mixtures are investigated. In the experiment, the laser ignition was used to achieve stable ignition of the ammonia/air mixtures with an equivalence ratio range from 0.7 to 1.4. The propagating flame was recorded with the high-speed shadowgraphy. Three different processing methods were introduced to calculate the laminar burning velocity with a consideration of the flame structure characteristics induced by the laser ignition. The effects of initial pressure (0.1 MPa–0.5 MPa), equivalence ratio (0.7–1.4), hydrogen fraction (0–20%) on the laminar burning velocity were investigated under the initial ambient temperature of 360 K. The state-of-the-art kinetic models were used to calculate the laminar burning velocities in the CHEMKIN-pro software. Both the simulation and experimental results show that the laminar burning velocity of the ammonia mixtures increases at first, reaches the peak around ϕ of 1.1, and then decreases with the equivalence ratio increasing from 0.7 to 1.4. The peak laminar burning velocities of the ammonia mixture are lower than 9 cm/s and are remarkably lower than those of hydrocarbon fuels. The laminar burning velocity of the ammonia mixture decreases with the increase of the initial ambient pressure, and it can be drastically speeded up with the addition of hydrogen. While the models except for those by Miller and Bian can give reasonable predictions compared to the experimental results for the equivalence ratio from 0.7 to 1.1 in the ammonia (80%)/hydrogen (20%)/air mixtures, all the kinetic models overpredict the experiments for the richer mixtures, indicating further work necessary in this respect.     

Improving burning speed by using hydrogen enrichment and turbulent jet ignition system in a rotary engine

Low flame speed restrains engine efficiency and increases HC emissions in rotary engines. Hydrogen addition and turbulent jet ignition have a great potential in increasing engine performance as they increase fuel burning speed. In this study, the classical R13b-Renesis Wankel engine and a modified one with a turbulent jet ignition configuration are numerically investigated by using hydrogen as a supplement. Eccentric motion of the rotor was generated by using User Defined Function in ANSYS-Fluent software. Pure methane and methane blended with 3% and 6% hydrogen energy fractions were used as fuels in the calculations. Combustion was modeled by using reduced mechanism of hydrogen-methane combustion having 22 species and 104 reactions. The Wankel engine was simulated at 2000 rpm speed and partial load conditions. At first, classical engine configuration having two spark plugs was simulated with pure methane. Then, hydrogen blended methane simulations were conducted to investigate the benefits of the hydrogen addition. Similar procedure was applied for the turbulent jet ignition application. The results show that both approaches are effective on increasing the burning speed of the fuel. It is revealed that hydrogen addition increases the indicated mean effective pressure (IMEP) by 1.8% and 5.2% for 3% and 6% hydrogen fraction cases respectively in the classical engine. Turbulent jet ignition with pure methane increases IMEP by 4.7% compared to the classical engine. Hydrogen addition only in pre-chamber is effective as much as 6% hydrogen fraction of classical engine. As the burning speed is increased by the application of these methods, CO and HC emissions are reduced and NO emission is increased. It is concluded that benefits of hydrogen addition and turbulent jet ignition applications can be optimized for both reducing harmful emissions and increasing engine performance.     

Investigation on the mixture formation,combustion characteristics and performance of a Diesel engine fueled with Diesel,Biodiesel B20 and hydrogen addition

An experimental and numerical study was performed to investigate the impact of Biodiesel B20 (blends 20% Rapeseed methyl ester with 80 % Diesel volumetric fraction) and different energetic fractions of hydrogen content (between 0 and 5%) on the mixture formation, combustion characteristics, engine performance and pollutant emissions formation. Experiments were carried out on a tractor Diesel engine, four-cylinders, four-stroke, 50 kW/2400 rpm, and direct injection. Simulations were conducted using the AVL codes (HYDSIM and BOOST 2013). Simulation results were validated against experimental data, by comparing the inline pressure, needle lift, in-cylinder pressure curves for Biodiesel B20 and pure Diesel fuels at 1400 rpm and 2400 rpm, respectively, under full load operating conditions. Good agreement with a maximum of 2.5% relative deviation on the peak results revealed that overall operation conditions Biodiesel B20 provides lower engine performance, efficiency, and emissions except the NOx which are slightly increased. The Biodiesel B20 has shorter ignition delay. By hydrogen addition to B20 with aspiration of the intake air flow the CO emissions, smoke, and total unburned hydrocarbon emissions THC decreased, while the NOx kept the same increasing trend for 1400 rpm and has not quite apparent trend for 2400 rpm. The enrichment by hydrogen of Diesel and B20 fuels has not a significant effect on ignition delay.     

Analysis of ignition delay period of a dual fuel diesel engine with hydrogen and LPG as secondary fuels

In this study, experiments were performed on 4 cylinder turbocharged, intercooled with 62.5 kW gen-set diesel engine by using hydrogen, liquefied petroleum gas (LPG) and mixture of LPG and hydrogen as secondary fuels. The experiments were performed to measure ignition delay period at different load conditions and various diesel substitutions. The experimental results have been compared with ignition delay correlation laid down by other researchers for diesel and dual fuel diesel engine. It is found that ignition delay equation based on pressure, temperature and oxygen concentration for a dual fuel diesel engine run on diesel-biogas gives variation up to 6.56% and 14.6% from the present experimental results, while ignition delay equation for a pure diesel engine gives 7.55% and 33.3% variation at lower and higher gaseous fuel concentrations, respectively. It is observed that the ignition delay of dual fuel engine depends not only on the type of gaseous fuels and their concentrations but also on charge temperature, pressure and oxygen concentration.     

Comparison of the combustion and emission characteristics of NH3/NH4NO2 and NH3/H2 in a two-stroke low speed marine engine

As a marine engine fuel of great concern, ammonia needs to be mixed with another high reactive fuel to improve its combustion performance. In this work, the combustion performance of NH₃/NH₄NO₂ and NH₃/H₂ was compared under different boundary conditions (excess air coefficient, initial temperature, pressure and mixing ratio). The numerical simulation of compression combustion is carried out under different power loads. The addition of ammonium nitrite decreases the ignition requirement of ammonia and shortens the ignition delay time of the mixture fuel. The boundary conditions of compression ignition can be reduced by mixing hydrogen and mixing ammonium nitrite, but it is not enough to achieve compression ignition under NH₃/H₂ mode. The addition of 30% ammonium nitrite can reduce the intake temperature to 300–360 K, which makes the compression ignition of the mixed fuel feasible. Meanwhile, in order to reduce the high in-cylinder combustion pressure and improve the combustion performance of the mixed fuel, the fuel injection strategy was proposed to achieve constant combustion pressure of 30 MPa under the premise of less power loss, which is a potential solution for the combustion of ammonia fuel.     

Effect of hydrogen addition on combustion and emissions performance of a spark ignition gasoline engine at lean conditions

Hydrogen has many excellent combustion properties that can be used for improving combustion and emissions performance of gasoline-fueled spark ignition (SI) engines. In this paper, an experimental study was carried out on a four-cylinder 1.6 L engine to explore the effect of hydrogen addition on enhancing the engine lean operating performance. The engine was modified to realize hydrogen port injection by installing four hydrogen injectors in the intake manifolds. The injection timings and durations of hydrogen and gasoline were governed by a self-developed electronic control unit (DECU) according to the commands from a calibration computer. The engine was run at 1400 rpm, a manifold absolute pressure (MAP) of 61.5 kPa and various excess air ratios. Two hydrogen volume fractions in the total intake of 3% and 6% were applied to check the effect of hydrogen addition fraction on engine combustion. The test results showed that brake thermal efficiency was improved and kept roughly constant in a wide range of excess air ratio after hydrogen addition, the maximum brake thermal efficiency was increased from 26.37% of the original engine to 31.56% of the engine with a 6% hydrogen blending level. However, brake mean effective pressure (Bmep) was decreased by hydrogen addition at stoichiometric conditions, but when the engine was further leaned out Bmep increased with the increase of hydrogen addition fraction. The flame development and propagation durations, cyclic variation, HC and CO₂ emissions were reduced with hydrogen addition. When excess air ratio was approaching stoichiometric conditions, CO emission tended to increase with the addition of hydrogen. However, when the engine was gradually leaned out, CO emission from the hydrogen-enriched engine was lower than the original one. NO_x emissions increased with the increase of hydrogen addition due to the raised cylinder temperature.     

Study of the cycle-to-cycle variations of an internal combustion engine fuelled with natural gas/hydrogen blends from the diagnosis of combustion pressure

A methodology is presented for studying the influence of using alternative fuels on the cycle-to-cycle variations of a spark ignition engine which has been fuelled with mixtures of natural gas and hydrogen in different proportions (0–100%). The experimental facility consists of a single-cylindrical spark ignition engine coupled to an asynchronous machine with a constant engine rotation speed of 1500 rpm. A thermodynamic combustion diagnostic model based on genetic algorithms is used to evaluate the combustion chamber pressure data experimentally obtained in the mentioned engine. The model is used to make the pressure diagnosis of series of 830 consecutive engine cycles automatically, with a high grade of objectivity of the combustion analysis, since the relevant adjustment parameters (i.e. pressure offset, effective compression ratio, top dead center angular position, heat transfer coefficients) are calculated by the genetic algorithm. Results indicate that the combustion process is dominated by the turbulence inside the combustion chamber (generated during intake and compression), showing little dependency of combustion variation on the mixture composition. This becomes more evident when relevant combustion variables are plotted versus the Mass Fraction Burned of each mixture. The only exception is the case of 100% hydrogen, due to the inherent higher laminar speed of hydrogen that causes combustion acceleration and thus turbulence generation.     

Effect of ignition timing and hydrogen fraction on combustion and emission characteristics of natural gas direct-injection engine

An experimental study on the combustion and emission characteristics of a direct-injection spark-ignited engine fueled with natural gas/hydrogen blends under various ignition timings was conducted. The results show that ignition timing has a significant influence on engine performance, combustion and emissions. The interval between the end of fuel injection and ignition timing is a very important parameter for direct-injection natural gas engines. The turbulent flow in the combustion chamber generated by the fuel jet remains high and relative strong mixture stratification is introduced when decreasing the angle interval between the end of fuel injection and ignition timing giving fast burning rates and high thermal efficiencies. The maximum cylinder gas pressure, maximum mean gas temperature, maximum rate of pressure rise and maximum heat release rate increase with the advancing of ignition timing. However, these parameters do not vary much with hydrogen addition under specific ignition timing indicating that a small hydrogen fraction addition of less than 20% in the present experiment has little influence on combustion parameters under specific ignition timing. The exhaust HC emission decreases while the exhaust CO₂ concentration increases with the advancing of ignition timing. In the lean combustion condition, the exhaust CO does not vary much with ignition timing. At the same ignition timing, the exhaust HC decreases with hydrogen addition while the exhaust CO and CO₂ do not vary much with hydrogen addition. The exhaust NOx increases with the advancing of ignition timing and the behavior tends to be more obvious at large ignition advance angle. The brake mean effective pressure and the effective thermal efficiency of natural gas/hydrogen mixture combustion increase compared with those of natural gas combustion when the hydrogen fraction is over 10%. __________ Translated from Transactions of CSICE, 2006, 24(5): 394–401 [译自:内燃机学报]     

Research on combustion and emission characteristics of a hydrous ethanol/hydrogen combined injection spark ignition engine under lean-burn conditions

Ethanol, as one of the carbon-neutral fuels for spark ignition (SI) engine, has been widely used. Dehydration and purification of ethanol during production process will lead to high energy consumption. If hydrous ethanol can be directly applied to the engine, the cost of use will be greatly reduced. Due to the high latent heat of vaporization of ethanol and water, it is necessary to consider the performance of atomization, evaporation and combustion stability when hydrous ethanol is used in engine. As a zero-carbon fuel, hydrogen has excellent characteristics such as low ignition energy, fast flame propagation speed and wide combustion limit. The combination of hydrous ethanol and hydrogen can reduce the use cost and ensure better combustion performance. Therefore, this study explores the performance of hydrous ethanol/hydrogen in SI combined injection engine. The hydrous ethanol is injected into the intake port and the hydrogen is directly injected into the cylinder during the compression stroke. In this study, we firstly analyze the optimal water blending ratio (ω) of hydrous ethanol, which including 0, 3%, 6%, 9% and 12%. The experimental results show that the hydrous ethanol with 9% water ratio has the best performance without hydrogen addition. Based on the 9% water ratio, the effects of hydrogen blending ratio (0, 5%, 10%, 15% and 20%) on the combustion and emission under different excess air ratio (λ) (1, 1.1, 1.2, 1.3, 1.4). Hydrogen addition can increase the degree of constant volume combustion, so that the maximum cylinder pressure and temperature increase with the increase of the hydrogen blending ratio (HBR). When λ = 1.3 and HBR = 20%, the maximum in-cylinder pressure can be increased by 108.64% compared to pure hydrous ethanol. Hydrogen effectively increases the indicated mean effective pressure (IMEP) and reduces the coefficient of variation of IMEP (COV_IMEP). Adding hydrogen can reduce CO and HC emissions, while NO_x emissions will increase. When λ = 1.2 and HBR increasing from 0 to 20%, the NOx emissions increase by 106.75%, but it is still less than the NOx emissions of pure hydrous ethanol at λ = 1. On the whole, hydrogen direct injection can improve the combustion performance of hydrous ethanol and achieve stable combustion under lean-burn conditions.     

Evaluating the effects of boosting intake-air pressure on the performance and environmental-economic indicators in a hydrogen-fueled SI engine

In this paper, the effects of external supercharger application on in-cylinder combustion, performance parameters, fuel efficiency and environmental-economic indicators are discussed together regarding a hydrogen-fueled spark ignition engine operating under a lean mixture. The engine was operated at an engine speed of 1600 rpm, under four different boosting pressures (between 10 kPa and 40 kPa), by optimized ignition timing and being compared to a normally aspirated condition. Hydrogen was injected at five bars into the inlet-air. The results show that the indicated mean effective pressure and thermal efficiency increased by 38.9% and 14.2%, respectively, with a 40 kPa boosting pressure under an optimized ignition timing condition according to the normally aspirated engine, and that the cyclic variation decreased by 15.5%. In addition, under 40 kPa boosting pressure, NO_x emissions increased by 45.2% and its environmental-social cost increased by 21.8%, while specific fuel consumption and fuel cost were reduced by approximately 18.5%.     

Starting a spark-ignited engine with the gasoline-hydrogen mixture

Because of the increased fuel-film effect and dropped combustion temperature, spark-ignited (SI) gasoline engines always expel large amounts of HC and CO emissions during the cold start period. This paper experimentally investigated the effect of hydrogen addition on improving the cold start performance of a gasoline engine. The test was carried out on a 1.6-L, four-cylinder, SI engine equipped with an electronically controlled hydrogen injection system. A hybrid electronic control unit (HECU) was applied to control the opening and closing of hydrogen and gasoline injectors. Under the same environmental condition, the engine was started with the pure gasoline and gasoline-hydrogen mixture, respectively. After the addition of hydrogen, gasoline injection duration was adjusted to ensure the engine to be started successfully. All cold start experiments were performed at the same ambient, coolant and oil temperatures of 17 °C. The test results showed that cylinder and indicated mean effective pressures in the first cycle were effectively improved with the increase of hydrogen addition fraction. Engine speed in the first 20 start cycles increased with hydrogen blending ratio. However, in later cycles, engine speed varied only a little with and without hydrogen addition due to the adoption of close loop control on engine speed. Because of the low ignition energy and high flame speed of hydrogen, both flame development and propagation durations were shortened after hydrogen addition. HC and CO emissions were dropped markedly after hydrogen addition due to the enhanced combustion process. When the hydrogen flow rate increased from 0 to 2.5 and 4.3 L/min, the instantaneous peak HC emissions were sharply reduced from 57083 to 17850 and 15738 ppm, respectively. NOx emissions were increased in the first 5 s and then reduced later after hydrogen addition.     

Research of performance and emission indicators of the compression-ignition engine powered by hydrogen - Diesel mixtures

The purpose of this study is to use the hydrogen – diesel mixture in Audi/VW 1.9 TDI turbocharged CI engine equipped with dynamometer and examine the performance and emission indicators by comparing it with sole diesel mode. The recent diesel emission scandals because of manufacturers cheating the laboratory tests, have initiated the discussions about the sustainable and environmentally friendly diesel engines. The CI engine without major engine modifications was set to operate at two speeds of 1900 rpm and 2500 rpm. At each of speed, the experiment was conducted at three BMEP: 0.4 MPa, 0.6 MPa, and 0.8 MPa. The test engine was operated using diesel fuel with amounts of 10 l/min, 20 l/min, and 30 l/min of hydrogen gas, supplied with air into intake manifold before the turbocharger. Relatively low hydrogen fraction (max. 15.74%) has effect on diesel combustion process and performance indicators at the all range of BMEP. The in-cylinder peak pressure at both speeds of 1900 rpm and 2500 rpm was lower than that with pure diesel fuel, as the small amount of hydrogen shortens the CI engine ignition delay period and decreases the rate of pressure rise. The decrease of BTE noticed, and increase of BSFC was registered with low hydrogen fraction (hydrogen amounts of 10 l/min, 20 l/min). However, with increase of hydrogen amount to 30 l/min, the BTE increased and BSFC decreased to the level, which was lower than that at the pure diesel test. The supply of hydrogen positively effects on engine emissions: the smokiness, NO_x, CO₂, CO decreased, the only hydrocarbon increased. The effect of hydrogen fraction on the combustion and emission characteristics of the diesel - hydrogen mixture was validated by AVL (Anstalt für Verbrennungskraftmaschinen List) BOOST and analysed with presentations of the main limitations and perspectives.     

Analysis of ignition delay by taking Di-tertiary-butyl peroxide as an additive in a dual fuel diesel engine using hydrogen as a secondary fuel

Ignition delay (ID) is one of the important parameters that make influenced on the combustion process inside the cylinder. This ignition delay affects not only the performances but also the noise and emissions of the engine. In this regards the experiments were conducted on single cylinder 4–stroke compression ignition research diesel engine, power 3.50 kW at constant speed 1500 rpm Kirloskar model TV1 with base fuel as diesel and hydrogen as secondary fuel with and without Di-tertiary-butyl-peroxide (DTBP). Experiments were conducted to measure the ignition delay of the dual fuel diesel (DFD) engine at different load conditions and substitution of diesel by hydrogen with or without DTBP and then it was compared with predicted ID given by Hardenberg-Hase equation and modified Hardenberg-Hase equation.The experimental values of ignition delay were compared with theoretical ignition delay which was predicted on the basis of Hardenberg-Hase equation by considering mean cylinder temperature, pressure, activation energy and cetane number and variations are found in between 6.60% and 21.22%. While, the Hardenberg-Hase equation was modified (by considering variation in activation energy) for DFD engine working on diesel as primary fuel and hydrogen as secondary fuel shows variations 1.20%–11.96%. Furthermore, with DTBP it gives variation up to 18.01%. It was found that ID decreases with increase in percentage of DTBP and hydrogen in air-fuel mixture. This might be due to the cetane improver nature of DTBP, pre-ignition reaction rate and energy release rate of hydrogen fuel. The polytropic index get increased by addition of (Di-tert butyl peroxide) DTBP. Similarly, 5% Di tertiary butyl peroxide reduces Ignition delay.     

Effect of ammonia addition on combustion and emission characteristics of hydrogen-fueled engine under lean-burn condition

Hydrogen (H₂) is a carbon-free fuel with many excellent combustion characteristics, but abnormal combustion is one of the main obstacles to the promotion and application of hydrogen-fueled engines. This experimental study aims to investigate the suppression of the heat release rate (HRR) of a hydrogen-fueled engine through the addition of ammonia (NH₃). The engine was run at 1300 rpm, with manifold absolute pressure (MAP) of 61 kPa and NH₃ addition ratio of 0% and 2.2%, under lean-burn conditions. The results showed that the addition of small amounts of ammonia reduced the combustion rate of the fuel mixture, prolonged the flame development period (CA0-10) and propagation durations (CA10-90) of the engine, and reduced the peak in-cylinder pressure and peak HRR under lean-burn conditions. The addition of ammonia increased the peak indicated mean effective pressure (IMEP) and the peak indicated thermal efficiency (ITE) of the engine. The addition of ammonia resulted in increased nitrogen oxides (NOx) emissions.     

Analysis of performance parameters of an ethanol fueled spark ignition engine operating with hydrogen enrichment

Concerns with the environment and energy security have increased interest in phasing out fossil fuels in the automotive industry, as it transitions from conventional internal combustion engines (ICE) to electric and fuel cell powertrains. During this transition, ethanol is of particular interest as a renewable fuel option in ICE, despite drawbacks compared to gasoline. Adding hydrogen to ethanol could remedy the disadvantages associated with ethanol, while maintaining the benefits of using renewable fuels. There is a gap in the literature of both experimental and numerical studies considering hydrogen addition in turbocharged ethanol engines. Therefore, this paper presents an experimental and numerical study of a turbocharged ethanol engine operating with hydrogen enrichment at stoichiometric conditions under boosted conditions. It was concluded that hydrogen addition allowed spark ignition engines to achieve lower brake specific energy consumption, better performance, and lower emissions. Thus, after proper calibration, a simulation model was created and shown to be a suitable tool to predict engine performance of a spark ignition engine operating with hydrogen enrichment and reduce the overall number of experimental tests needed to tune engines operating with this fuel blend. Finally, some operating strategies are recommended based on these findings.     

Effects of hydrogenation of fossil fuels with hydrogen and hydroxy gas on performance and emissions of internal combustion engines

Energy security is an important consideration for development of future transport fuels. Among the all gaseous fuels hydrogen or hydroxy (HHO) gas is considered to be one of the clean alternative fuels. Hydrogen is very flammable gas and storing and transporting of hydrogen gas safely is very difficult. Today, vehicles using pure hydrogen as fuel require stations with compressed or liquefied hydrogen stocks at high pressures from hydrogen production centres established with large investments.Different electrode design and different electrolytes have been tested to find the best electrode design and electrolyte for higher amount of HHO production using same electric energy. HHO is used as an additional fuel without storage tanks in the four strokes, 4-cylinder compression ignition engine and two-stroke, one-cylinder spark ignition engine without any structural changes. Later, previously developed commercially available dry cell HHO reactor used as a fuel additive to neat diesel fuel and biodiesel fuel mixtures. HHO gas is used to hydrogenate the compressed natural gas (CNG) and different amounts of HHO-CNG fuel mixtures are used in a pilot injection CI engine. Pure diesel fuel and diesel fuel + biodiesel mixtures with different volumetric flow rates are also used as pilot injection fuel in the test engine. The effects of HHO enrichment on engine performance and emissions in compression-ignition and spark-ignition engines have been examined in detail. It is found from the experiments that plate type reactor with NaOH produced more HHO gas with the same amount of catalyst and electric energy. All experimental results from Gasoline and Diesel Engines show that performance and exhaust emission values have improved with hydroxy gas addition to the fossil fuels except NO_x exhaust emissions. The maximum average improvements in terms of performance and emissions of the gasoline and the diesel engine are both graphically and numerically expressed in results and discussions. The maximum average improvements obtained for brake power, brake torque and BSFC values of the gasoline engine were 27%, 32.4% and 16.3%, respectively. Furthermore, maximum improvements in performance data obtained with the use of HHO enriched biodiesel fuel mixture in diesel engine were 8.31% for brake power, 7.1% for brake torque and 10% for BSFC.     

Pressure limit of hydrogen spontaneous ignition in a T-shaped channel

This paper describes a large eddy simulation model of hydrogen spontaneous ignition in a T-shaped channel filled with air following an inertial flat burst disk rupture. This is the first time when 3D simulations of the phenomenon are performed and reproduced experimental results by Golub et al. (2010). The eddy dissipation concept with a full hydrogen oxidation in air scheme is applied as a sub-grid scale combustion model to enable use of a comparatively coarse grid to undertake 3D simulations. The renormalization group theory is used for sub-grid scale turbulence modelling. Simulation results are compared against test data on hydrogen release into a T-shaped channel at pressure 1.2–2.9 MPa and helped to explain experimental observations. Transitional phenomena of hydrogen ignition and self-extinction at the lower pressure limit are simulated for a range of storage pressure. It is shown that there is no ignition at storage pressure of 1.35 MPa. Sudden release at pressure 1.65 MPa and 2.43 MPa has a localised spot ignition of a hydrogen-air mixture that quickly self-extinguishes. There is an ignition and development of combustion in a flammable mixture cocoon outside the T-shaped channel only at the highest simulated pressure of 2.9 MPa. Both simulated phenomena, i.e. the initiation of chemical reactions followed by the extinction, and the progressive development of combustion in the T-shape channel and outside, have provided an insight into interpretation of the experimental data. The model can be used as a tool for hydrogen safety engineering in particular for development of innovative pressure relief devices with controlled ignition.     

Experimental and computational study on the enhancement of engine characteristics by hydrogen enrichment in a biogas fuelled spark ignition engine

Limitations on the upgradation of biogas to biomethane in terms of cost effectiveness and technology maturity levels for stationary power generation purpose in rural applications have redirected the research focus towards possibilities for enhancement of biogas fuel quality by blending with superior quality fuels. In this work, the effect of hydrogen enrichment on performance, combustion and emission characteristics of a single-cylinder, four-stroke, water-cooled, biogas fuelled spark-ignition engine operated at the compression ratio of 10:1 and 1500 rpm has been evaluated using experimental and computational (CFD) studies. The percentage share of hydrogen in the inducted biogas fuel mixture was increased from 0 to 30%, and engine characteristics with pure methane fuel was considered as a baseline for comparative analysis. The CFD model is developed in Converge CFD software for a better understanding on combustion phenomenon and is validated with experimental data. In addition, the percentage share of hydrogen enrichment which would serve as a compromise between biogas upgradation cost and engine characteristics is also identified. The results of study indicated an enhancement in combustion characteristics (peak in-cylinder pressure increased; COV_IMEP reduced from 9.87% to 1.66%; flame initiation and combustion durations reduced) and emission characteristics (hydrocarbon emissions reduced, and NOx emissions increased but still lower than pure methane) with increase in hydrogen share from 0 to 30% in biogas fuelled SI engine. Flame propagation speed increased and combustion duration reduced with hydrogen supplementation and the same was evident from the results of the CFD model. Performance of the engine increased with increase in hydrogen share up to 20% and further increment in hydrogen share degraded the performance, owing to heat losses and the enhancement in combustion characteristics were relatively small. Overall, it was found that 20% blending of hydrogen in the inducted biogas fuel mixture will be effective in enhancing the engine characteristics of biogas fuelled engines for stationary power generation applications and it holds a good compromise between biogas upgradation cost and engine performance.     

Particulate characteristics of laser ignited hydrogen enriched compressed natural gas engine

Laser ignition (LI) is emerging as a strong technology to control the oxides of nitrogen (NOx) emissions from spark ignition (SI) engines without the need for any significant exhaust gas after-treatment and is an appropriate technology for meeting future emission norms in the automotive sector. In this study, particulate characteristics of LI engine fuelled with different compressed natural gas (CNG) and hydrogen mixtures [100% CNG, 10HCNG (10% v/v hydrogen with 90% v/v CNG), 30HCNG (30% v/v hydrogen with 70% v/v CNG), 50HCNG (50% v/v hydrogen with 50% v/v CNG) and 100% hydrogen] were investigated. Experiments were performed in a suitably modified single cylinder engine, which operated in LI mode at constant engine speed (1500 rpm) at five different engine loads (5, 10, 15, 20 and 25 Nm). Particulate characteristics were determined using an engine exhaust particle sizer (EEPS). Results showed that particle number concentration increased with increasing engine load. Number-size, surface area-size and mass-size distributions of particulates reflected that addition of hydrogen in the CNG improved particulate emission characteristics especially in nucleation mode particle (NMP) size range (10 nm < Dp < 50 nm). Among the test fuels, hydrogen-fuelled engine emitted the lowest number of particles. It was observed that the difference between particulate characteristics emitted by different test fuels reduced at higher engine loads. Significant contribution of lubricating oil in particulate emissions from both hydrogen as well as HCNG fuelled LI engine was an important finding of this study. Dominant contribution of larger particles (Dp > 50 nm) in total particle mass (TPM) was an important observation of this study. The qualitative correlation between total particle number (TPN) and TPM indicated that suitable fuel composition at different engine loads yielded cleaner exhaust from the LI engine. Overall, this study demonstrated that addition of hydrogen in CNG is advantageous from particulate reduction point of view, however, optimum fuel composition should be adjusted according to engine operating condition in order to reduce particulate emissions.