Effects of hydrogenation of fossil fuels with hydrogen and hydroxy gas on performance and emissions of internal combustion engines

Energy security is an important consideration for development of future transport fuels. Among the all gaseous fuels hydrogen or hydroxy (HHO) gas is considered to be one of the clean alternative fuels. Hydrogen is very flammable gas and storing and transporting of hydrogen gas safely is very difficult. Today, vehicles using pure hydrogen as fuel require stations with compressed or liquefied hydrogen stocks at high pressures from hydrogen production centres established with large investments.Different electrode design and different electrolytes have been tested to find the best electrode design and electrolyte for higher amount of HHO production using same electric energy. HHO is used as an additional fuel without storage tanks in the four strokes, 4-cylinder compression ignition engine and two-stroke, one-cylinder spark ignition engine without any structural changes. Later, previously developed commercially available dry cell HHO reactor used as a fuel additive to neat diesel fuel and biodiesel fuel mixtures. HHO gas is used to hydrogenate the compressed natural gas (CNG) and different amounts of HHO-CNG fuel mixtures are used in a pilot injection CI engine. Pure diesel fuel and diesel fuel + biodiesel mixtures with different volumetric flow rates are also used as pilot injection fuel in the test engine. The effects of HHO enrichment on engine performance and emissions in compression-ignition and spark-ignition engines have been examined in detail. It is found from the experiments that plate type reactor with NaOH produced more HHO gas with the same amount of catalyst and electric energy. All experimental results from Gasoline and Diesel Engines show that performance and exhaust emission values have improved with hydroxy gas addition to the fossil fuels except NO_x exhaust emissions. The maximum average improvements in terms of performance and emissions of the gasoline and the diesel engine are both graphically and numerically expressed in results and discussions. The maximum average improvements obtained for brake power, brake torque and BSFC values of the gasoline engine were 27%, 32.4% and 16.3%, respectively. Furthermore, maximum improvements in performance data obtained with the use of HHO enriched biodiesel fuel mixture in diesel engine were 8.31% for brake power, 7.1% for brake torque and 10% for BSFC.     

Effect of hydroxy (HHO) gas addition on performance and exhaust emissions in compression ignition engines

In this study, hydroxy gas (HHO) was produced by the electrolysis process of different electrolytes (KOH_(aq), NaOH_(aq), NaCl_(aq)) with various electrode designs in a leak proof plexiglass reactor (hydrogen generator). Hydroxy gas was used as a supplementary fuel in a four cylinder, four stroke, compression ignition (CI) engine without any modification and without need for storage tanks. Its effects on exhaust emissions and engine performance characteristics were investigated. Experiments showed that constant HHO flow rate at low engine speeds (under the critical speed of 1750 rpm for this experimental study), turned advantages of HHO system into disadvantages for engine torque, carbon monoxide (CO), hydrocarbon (HC) emissions and specific fuel consumption (SFC). Investigations demonstrated that HHO flow rate had to be diminished in relation to engine speed below 1750 rpm due to the long opening time of intake manifolds at low speeds. This caused excessive volume occupation of hydroxy in cylinders which prevented correct air to be taken into the combustion chambers and consequently, decreased volumetric efficiency was inevitable. Decreased volumetric efficiency influenced combustion efficiency which had negative effects on engine torque and exhaust emissions. Therefore, a hydroxy electronic control unit (HECU) was designed and manufactured to decrease HHO flow rate by decreasing voltage and current automatically by programming the data logger to compensate disadvantages of HHO gas on SFC, engine torque and exhaust emissions under engine speed of 1750 rpm. The flow rate of HHO gas was measured by using various amounts of KOH, NaOH, NaCl (catalysts). These catalysts were added into the water to diminish hydrogen and oxygen bonds and NaOH was specified as the most appropriate catalyst. It was observed that if the molality of NaOH in solution exceeded 1% by mass, electrical current supplied from the battery increased dramatically due to the too much reduction of electrical resistance. HHO system addition to the engine without any modification resulted in increasing engine torque output by an average of 19.1%, reducing CO emissions by an average of 13.5%, HC emissions by an average of 5% and SFC by an average of 14%.     

Performance & emission analysis of HHO enriched dual-fuelled diesel engine with artificial neural network prediction approaches

Most of the studies on conventional fuel types that can be used in internal combustion engines have been made in order to improve performance values. Nowadays environmental problems have shown that emission values are more important and interest in low carbon alternative fuels has highly increased in recent years. In this study, performance and emission values of soybean biodiesel (B25) fuel mixture used in diesel engine were investigated in detail by making different ratios of hydroxy (HHO) enrichment (3, 5 and 7 L/min). HHO enrichments increased brake torque and power outputs with direct correlation to flow rate amount; at the same time brake specific fuel consumption has decreased. Also, one of the main objectives of this study is to predict the optimum hydrogen requirement against performance reductions and NO_x formations among test fuels (3, 5, and 7 L/min HHO enriched B25), too by using artificial intelligence. For developing the ANN structure, Levenberg-Marquardt (LM) learning algorithm was used to adjust the weights in the cascade forward network. The results show that the ANN model has 95,82%, 96,07%, and 92,35% estimation accuracies for motor torque, motor power, and NO_x emission, respectively.     

Premixed ammonia/hydrogen swirl combustion under rich fuel conditions for gas turbines operation

Energy storage is one of the highest priority challenges in transitioning to a low-carbon economy. Fluctuating, intermittent primary renewable sources such as wind and solar require low-carbon storage options to enable effective load matching, ensuring security of supply. Chemical storage is one such option, with low or zero carbon fuels such as hydrogen, alcohols and ammonia having been proposed. Ammonia provides zero-carbon hydrogen storage whilst offering liquefaction at relatively low pressures and atmospheric temperatures, enabling ease of transportation in a pre-existing infrastructure. Ammonia can also be used directly as a fuel in power plants such as gas turbines to avoid complete conversion back to hydrogen. It is a relatively unreactive fuel, and so it is of interest to explore the potential utilisation of ammonia/hydrogen mixtures. Hence, the goal of this paper is to provide a first assessment of the suitability of a chosen 70%NH₃30%H₂ (%vol) blend for utilisation within a gas turbine environment, based on primary combustion diagnostics including combustion stability – via OH chemiluminescence - and emissions (NO_x and NH₃). An established optical generic swirl-burner enabled studies of the influence of equivalence ratio (φ > 1), ambient temperature (<484 ± 10 K) and bypass air, with a focus on NO_x reduction, one of the main challenges for ammonia combustion. A numerical GT cycle model is developed alongside the experimental investigation. The results demonstrate that the blend has considerable potential as a fuel substitute with reasonable combustion stability and significant reduction of emissions for the cases without bypass air, due to increased chemical reactivity of unburned ammonia. However, emissions are still above those recommended for gas turbine cycles, with a theoretical cycle that still produces low efficiencies compared to DLN methane, highlighting the requirement for new injection techniques to reduce NO_x/unburned NH₃ in the flue gases whilst ensuring increased power outputs.     

Comparative study on combustion and emission of SI engine blended with HHO by different injection modes of gasoline

As a hydrogen fuel for real-time production without storage, HHO has great research prospect and significance. In this paper, we conducted experiments on a spark ignition (SI) engine which has two independent fuel supply systems to compare two combination modes of gasoline port injection plus HHO (GPI + HHO) and gasoline direct injection plus HHO (GDI + HHO) at different HHO flow rate, λ, engine speed and load. The results show that, in both modes, HHO addition increases the maximum cylinder pressure and torque. With the increase of HHO flow rate, the flame development period and flame propagation period shorten, the crank angle corresponding to the maximum cylinder pressure is closer to top dead center. In addition, GDI + HHO mode has better engine performance. HHO has a significant effect on improving combustion stability. Especially at λ = 1.4, as HHO flow rate increases from 0 to 16 L/min, the coefficient of indicated mean effective pressure variation of GPI + HHO and GDI + HHO mode decreases by 69.17% and 58.29%, respectively. Moreover, HHO addition improves HC and CO emissions but increases NOx emissions. CO and HC emissions of GDI + HHO mode are the lowest under all conditions, and reaching the lowest value when HHO flow rate = 16 L/min. Besides, GDI + HHO mode not only has lower NO emissions under normal working conditions (λ = 1) but also can maintain a better combustion environment under lean-burn conditions (λ = 1.2, 1.4). In general, the application of HHO as fuel in engine can improve combustion and emission characteristics and GDI + HHO mode is the best combination of gasoline and HHO.     

Thermodynamic analysis of solar energy use for reforming fuels to hydrogen

In this paper, a method is proposed for reforming fuels to hydrogen using solar energy at distributed locations (industrial sites, residential and commercial buildings fed with natural gas, remote settlements supplied by propane etc). In order to harness solar energy a solar concentrator is used to generate high temperature heat to reform fuels to hydrogen. A typical fuel such as natural gas, propane, methanol, or an atypical fuel such as ammonia or urea can be transported to distributed locations via gas networks or other means. The thermodynamic analysis of the process shows the general reformation reactions for NH₃, CH₄ and C₃H₈ as the input fuel by comparison through operational fuel cost and CO₂ mitigation indices. Through a cost analysis, cost reduction indices show fuel-usage cost reductions of 10.5%, 22.1%, and 22.2% respectively for the reformation of ammonia, methane, and propane. CO₂ mitigation indices show fuel-usage CO₂ mitigations of 22.1% and 22.3% for methane and propane respectively, where ammonia reformation eliminates CO₂ emission at the fuel-usage stage. The option of reforming ammonia is examined in further detail as proposed cycles for solar energy capture are considered. A mismatch of specific heats from the solar dish is observed between incoming and outgoing streams, allowing a power production system to be included for a more complete energy capture. Further investigation revealed the most advantageous system with a direct expansion turbine being considered rather than an external power cycle such as Brayton or Rankine type cycles. Also, an energy efficiency of approximately 93% is achievable within the reformation cycle.     

Ammonia as hydrogen carrier for transportation; investigation of the ammonia exhaust gas fuel reforming

In this paper we show, for the first time, the feasibility of ammonia exhaust gas reforming as a strategy for hydrogen production used in transportation. The application of the reforming process and the impact of the product on diesel combustion and emissions were evaluated. The research was started with an initial study of ammonia autothermal reforming (NH₃ – ATR) that combined selective oxidation of ammonia (into nitrogen and water) and ammonia thermal decomposition over a ruthenium catalyst using air as the oxygen source. The air was later replaced by real diesel engine exhaust gas to provide the oxygen needed for the exothermic reactions to raise the temperature and promote the NH₃ decomposition. The main parameters varied in the reforming experiments are O₂/NH₃ ratios, NH₃ concentration in feed gas and gas – hourly – space – velocity (GHSV). The O₂/NH₃ ratio and NH₃ concentration were the key factors that dominated both the hydrogen production and the reforming process efficiencies: by applying an O₂/NH₃ ratio ranged from 0.04 to 0.175, 2.5–3.2 l/min of gaseous H₂ production was achieved using a fixed NH₃ feed flow of 3 l/min. The reforming reactor products at different concentrations (H₂ and unconverted NH₃) were then added into a diesel engine intake. The addition of considerably small amount of carbon – free reformate, i.e. represented by 5% of primary diesel replacement, reduced quite effectively the engine carbon emissions including CO₂, CO and total hydrocarbons.     

The regulation effect of methane and hydrogen on the emission characteristics of ammonia/air combustion in a model combustor

Ammonia, made up of 17.8% hydrogen, has attracted a lot of attention in combustion community due to its zero carbon emission as a fuel in gas turbines. However, ammonia combustion still faces some challenges including the weak combustion and sharp NOx emissions which discourage its application. It was demonstrated that the combustion intensity of ammonia/air flame can be enhanced through adding active fuels like methane and hydrogen, while the NOx emission issue will emerge in the meantime. This study investigates regulation effect of methane and hydrogen on the emission characteristics of ammonia/air flame in a gas turbine combustor. The instantaneous OH profile and global emissions at the combustion chamber outlet are measured with Planar Laser Induced Fluorescence (PLIF) technique and the Fourier Transform Infrared (FTIR), respectively. The flames are also simulated by large eddy simulation to further reveal physical and chemical processes of the emissions formation. Results show that for NH₃/air flames, the emissions behavior of the gas turbine combustor is similar to the calculated one-dimensional flames. Moreover, the NOx emissions and the unburned NH₃ can be simultaneously controlled to a proper value at the equivalence ratio (φ) of approximate 1.1. The variation of NO and NO₂ with φ for NH₃/H₂/air flames and NH₃/CH₄/air flames at blending ratio (Z_f) of 0.1 are similar to the NH₃/air flames, with the peak moving towards rich condition. This indicates that the NH₃/air flame can be regulated through adding a small amount of active fuels without increasing the NOx emission level. However, when Z_f = 0.3, we observe a clear large NOx emission and CO for NH₃/CH₄/air flames, indicating H₂ is a better choice on the emission control. The LES results show that NO and OH radicals exhibit a general positive correlation. And the temperature plays a secondary role in promoting NOx formation comparing with CH₄/air flame.     

Using HHO (Hydroxy) and hydrogen enriched castor oil biodiesel in compression ignition engine

Hydrogen and HHO enriched biodiesel fuels have not been investigated extensively for compression ignition engine. This study investigated the performance and emissions characteristics of a diesel engine fueled with hydrogen or HHO enriched Castor oil methyl ester (CME)-diesel blends. The production and blending of CME was carried out with a 20% volumetric ratio (CME20) using diesel fuel. In addition, the enrichment of intake air was carried out using pure HHO or hydrogen through the intake manifold with no structural changes – with the exception of the reduction of the amount of diesel fuel – for a naturally aspirated, four cylinder diesel engine with a volume of 3.6 L. Hydrogen amount was kept constant with a ratio of 10 L/min throughout the experiments. Engine performance parameters, including Brake Power, Brake Torque, Brake Specific Fuel Consumption and exhaust emissions – including NOx and CO, – were tested at engine speeds between 1200 and 2600 rpm. It is seen that HHO enriched CME has better results compared to pure hydrogen enrichment to CME. An average improvement of 4.3% with HHO enriched CME20 was found compared to diesel fuel results while pure hydrogen enriched CME20 fuel resulted with an average increase of 2.6%. Also, it was found that the addition of pure hydrogen to CME had a positive effect on exhaust gas emissions compared to that adding HHO. The effects of both enriched fuels on the engine performance were minimal compared to that of diesel fuel. However, the improvements on exhaust gas emissions were significant.     

Performance assesment of hydrogen and ammonia combustion with various fuels for power generators

This paper proposes the use of hydrogen and ammonia as possible fuels for power generators and to do so the combustion is modelled by using different types of fuels which are; hydrogen, gasoline, diesel, ethanol, methanol, propane, butane and natural gas to see the effects of these fuel sources on combustion. The main aim of using a clean fuel is to decrease the greenhouse emissions, and by looking at the results, the reduction in CO₂ emissions shows that blending hydrogen and ammonia will result in a reduction for the deleterious emissions occurring after combustion. The reason behind using a dual fueled system is to make use of the secondary fuel source as a combustion promoter to help increase the low flame temperatures of ammonia that causes it not to ignite when used solely. In the modelling of combustion the maximum power output is set to 3.65 kW as this is the maximum power output for the power generator used in the experimental studies. In the studies the increase of clean fuel percentage in the fuel blend cause a reduction in the performance measures as expected with the lower energy density and lower heating values that ammonia offers but the reduction in CO₂ and NO_x emissions makes it a fuel source worth using with a combustion promoter.     

Impact of HHO gas enrichment and high purity biodiesel on the performance of a 315 cc diesel engine

Biodiesel and oxyhydrogen (HHO) gas have shown promising results in improving engine performance and emissions. In this work, the effects of HHO gas and 5% biodiesel blends (B5) and their combined use in a 315 cc diesel engine have been analyzed. Biodiesel is produced by base catalyzed transesterification and cleaned by emulsification. Its calculated cetane index (CCI) was 61.4. HHO gas is produced from electrolysis of concentrated potassium hydroxide solution. The use of 5% biodiesel blend resulted in a significant rise of 9.4% in the brake thermal efficiency (BTE) and a maximum reduction of 8.19% in the brake specific fuel consumption (BSFC). HHO enrichment of diesel and biodiesel at 2.81 L/min through the intake manifold improved the torque and power by an average of over 3%. HHO addition also improved the BTE of diesel by a maximum of 3.67%. The combination of high CCI biodiesel fuel and HHO creates a mixture that has shortened the ignition delay (ID) to the point that adverse effects were observed due to the premature combustion as shown by the average decrease in the BTE of 2.97% compared to B5. Thus, B5, on its own, is found to be the optimum fuel under these conditions.     

Ammonia-hydrogen-air gas turbine cycle and control analyses

Blending ammonia with hydrogen has the potential of replacing conventional hydrocarbon fuels to reduce carbon emissions. However, the uncertainties of determining safe, stable, and efficient operating conditions remain a great challenge. Furthermore, although control technologies have been in the scope of interest for gas turbine manufacturers, those are not yet specialized for NH₃–H₂/air gas turbines. Therefore, this paper identifies the cycle performance of an NH₃–H₂/air gas turbine in comparison to a CH₄/air gas turbine, thus highlighting the operating conditions in which the NH₃–H₂/air gas turbines show higher performance compared to the CH₄/air gas turbines. The results have been obtained by developing a LabVIEW code which has also been utilized to serve as a control code for the NH₃–H₂/air and CH₄/air gas turbines. The system identification stage of calibrating the controller has been achieved for both gas turbines by determining the system's sensitivities, thus providing an accurate calibration of the controlling parameters.     

Recalibration of carbon-free NH3/H2 fuel blend process: Qatar's roadmap for blue ammonia

Due to growing concerns about carbon emissions, using zero-carbon fuels has become an interesting alternative to overcome this problem. The NH₃(70%)-H₂(30%) fuel blend is an innovative fuel example that has the potential to replace conventional hydrocarbon fuels. Studies on the NH₃(70%)-H₂(30%) fuel blend have shown its superior combustion performance and its effect on enhancing cycle efficiency compared to other compositions of the NH₃–H₂ blends. However, without calibrating ammonia plants and simply mixing portions of the produced pure ammonia to hydrogen at the desired molar fraction essentially requires coupling ammonia plants with other hydrogen-producing plants, leading to potential difficulties in commercializing the unused (as fuel in the NH₃–H₂/air gas turbines) hydrogen portions from the hydrogen-producing plan. Therefore, in this paper, as an attempt to utilize the existing ammonia production infrastructure and facility without acquiring major changes that could lead to resisting the adoption of the NH₃(70%)-H₂(30%) fuel blend, the independent parameters of a conventional ammonia plant have been calibrated, and the reactors have been sized to provide a continuous supply of the NH₃(70%)-H₂(30%) fuel blend with the exact molar fraction to run a power plant. Calibrating of the ammonia plant has been performed using an ASPEN PLUS model.     

Optimisation of dry cell electrolyser and hydroxy gas production to utilise in a diesel engine operated with blends of orange peel oil in dual-fuel mode

This study aims at producing hydroxy (HHO) gas using a dry cell electrolysis setup and utilising it along with orange oil in a diesel engine. First an electrolyser was designed considering the optimised values of the material (SS316L), electrolyte (NaOH), and electrode gap (2 mm). Then the biodiesel obtained from the waste orange peels, after transesterification, were blended with diesel at 25 and 50% by vol. The HHO gas was produced by the water electrolysis method by a plate-type electrolyser having a maximum production rate of 2.5 LPM with NaOH as the electrolyte. HHO gas was inducted through the inlet manifold along with the fresh air at a constant rate of 2 LPM with both the biodiesel blends. The performance, emission, and combustion outcomes of the single cylinder diesel engine for different load conditions (0–100%) were tested for all the blends with and without HHO addition. The results showed a considerable increase in brake thermal efficiency of 1.54% at full load condition, with a noticeable decrease in fuel consumption by 11.1% compared to conventional diesel fuel, was achieved for the O25 blend with HHO induction. Moreover, emissions like hydrocarbon, carbon monoxide and smoke were reduced by 17.6, 29.5, and 12.1%, respectively. However, the improvement in combustion outcomes led to the increase in nitrogen oxides emission by 9.67%. This study helped to understand the production process of HHO gas by dry cell electrolyser and its effect on the blend of orange oil methyl ester and diesel in dual-fuel mode.     

Burning velocity and flame structure of CH4/NH3/air turbulent premixed flames at high pressure

Ammonia is one of the most promising alternative fuels. In particular, ammonia combustion for gas turbine combustors for power generation is expected. To shift the fuel for a gas turbine combustor to ammonia step-by-step, the partial replacement of natural gas by ammonia is considered. To reveal the turbulent combustion characteristics, CH₄/NH₃/air turbulent premixed flame at 0.5 MPa was experimentally investigated. The ammonia ratio based on the mole fraction and lower heating value was varied from 0 to 0.2. The results showed that the ratio of the turbulent burning velocity and unstretched laminar burning velocity decreased with an increase in the ammonia ratio. The reason for this variation is that the flame area decreased with an increase in the ammonia ratio as the flame surface density decreased and the fractal inner cutoff increased. The volume fractions in the turbulent flame region were almost the same with ammonia addition, indicating that combustion oscillation can be handled in a manner similar to that for the case of natural gas for CH₄/NH₃/air flames.     

Thermo-electrochemical modeling of ammonia-fueled solid oxide fuel cells considering ammonia thermal decomposition in the anode

Ammonia (NH₃) is a promising hydrogen carrier and a possible fuel for use in Solid Oxide Fuel Cells (SOFCs). In this study, a 2D thermo-electrochemical model is developed to investigate the heat/mass transfer, chemical (ammonia thermal decomposition) and electrochemical reactions in a planar SOFC running on ammonia. The model integrates three sub-models: (1) an electrochemical model relating the current density-voltage characteristics; (2) a chemical model calculating the rate of ammonia thermal decomposition reaction; (3) a 2D computational fluid dynamics (CFD) model that simulates the heat and mass transfer phenomena. Simulations are conducted to study the complicated physical-chemical processes in NH₃-fueled SOFCs. It is found that increasing the inlet temperature of NH₃-fueled SOFC is favorable for a higher electric output, but the temperature gradient in the SOFC is considerably higher, particularly near the inlet of the SOFC. The effects of operating potential and inlet gas velocity on NH₃-fueled SOFC performance are investigated. It is found that an increase in inlet gas velocity from 1 m s⁻¹ to 10 m s⁻¹ slightly decreases the SOFC performance and does not affect the temperature field significantly. For comparison, decreasing the gas velocity to 0.2 m s⁻¹ is more effective to reduce the temperature gradient in SOFC.     

Assessing the effects of partially decarbonising a diesel engine by co-fuelling with dissociated ammonia

The proven feasibility of ammonia combustion in compression-ignition engines has led to it being considered as a carbon-free replacement for diesel fuel. Due to its high auto-ignition temperature, however, a more realistic strategy would be to aim for a step-change reduction in carbon emissions by co-fuelling a diesel engine with ammonia. In assessing this strategy, ammonia gas was introduced into the air-intake manifold of a compression-ignition engine, while diesel fuel was injected directly into the cylinder to ignite the mixture. By substituting only 3% of the air intake by ammonia, the diesel consumption and the CO₂ emissions decreased by 15%. The combustion and emission characteristics were then compared when the same percentage of air intake (by mass) was substituted by either dissociated ammonia (a mixture of H₂, N₂ with small percentages of NH₃) or pure hydrogen, to mimic the other possible forms in which the co-fuel can be delivered to the engine. The addition of pure hydrogen resulted in the best engine performance, both in terms of combustion efficiency and regulated emission quality. The thermal combustion efficiency declined by only ∼0.5% when the H₂ was replaced by undissociated ammonia at low load, but N₂O now appeared in the emissions. Co-fuelling the engine with dissociated ammonia may provide the ideal compromise in terms of thermal combustion efficiency and emission quality, while also providing a waste-heat recovery mechanism.     

Comparison of the combustion and emission characteristics of NH3/NH4NO2 and NH3/H2 in a two-stroke low speed marine engine

As a marine engine fuel of great concern, ammonia needs to be mixed with another high reactive fuel to improve its combustion performance. In this work, the combustion performance of NH₃/NH₄NO₂ and NH₃/H₂ was compared under different boundary conditions (excess air coefficient, initial temperature, pressure and mixing ratio). The numerical simulation of compression combustion is carried out under different power loads. The addition of ammonium nitrite decreases the ignition requirement of ammonia and shortens the ignition delay time of the mixture fuel. The boundary conditions of compression ignition can be reduced by mixing hydrogen and mixing ammonium nitrite, but it is not enough to achieve compression ignition under NH₃/H₂ mode. The addition of 30% ammonium nitrite can reduce the intake temperature to 300–360 K, which makes the compression ignition of the mixed fuel feasible. Meanwhile, in order to reduce the high in-cylinder combustion pressure and improve the combustion performance of the mixed fuel, the fuel injection strategy was proposed to achieve constant combustion pressure of 30 MPa under the premise of less power loss, which is a potential solution for the combustion of ammonia fuel.     

Experimental study of a domestic boiler using hydrogen methane blend and fuel-rich staged combustion

Storing excess wind and solar energy in the form of hydrogen injected into the natural gas grid is one of the main ingredients of the energy transition. This hydrogen injection has an impact on emissions and the performance of user equipment. The present work reports on an experimental study of the combustion of methane-hydrogen mixture with fuel rich transverse staggered injection. The 15 kW domestic boiler used was equipped with 16 burners (2 × 8). The aim of this work is to better understand the simultaneous effects of fuel rich staged combustion (Ø = 2.0 ÷ 4.0), hydrogen blending of methane (0 ÷ 45%) on pollutant emissions and efficiency while maintaining a compromise between high power, fuel economy and low emissions. The results show that NO_x, CO₂ emissions decrease, CO and C_xH_y emission values increase and thermal efficiency values decrease with increasing hydrogen percentage and fuel rich staggering combustion.     

Emission characteristics and heat release rate surrogates for ammonia premixed laminar flames

Ammonia is a carbon-free fuel that has the potential to meet increasing energy demand and to reduce CO₂ emissions. In the present work, the characteristics of pollutant emissions in ammonia premixed laminar flames are investigated using one-dimensional simulations, and heat release rate (HRR) surrogates for ammonia combustion are proposed. Both atmospheric and high-pressure conditions were considered, and four representative mechanisms for ammonia combustion were employed. It is shown that the total emission of NO and NH₃ achieves a minimum around an equivalence ratio (?) of 1.1 under atmospheric conditions, and there is no noticeable emission of NO and NH₃ for ? = 1.1 ~ 1.5 under high-pressure conditions. Three HRR surrogates, [NH₃][OH], [NH₂][O], and [NH₂][H], were proposed based on the analysis of HRR and elementary reaction profiles. The performance of HRR surrogates was found to vary with equivalence ratios. For example, with the Miller mechanism, [NH₃][OH], [NH₂][O], and [NH₂][H] have the best performance under atmospheric conditions at ? = 1.15, 0.95 and 1.05, respectively, and under high-pressure conditions at ? = 1.11, 0.87 and 0.96, respectively. Similar conclusions can also be drawn with other mechanisms. These findings provide valuable insights into emission control and flame identification of ammonia combustion.