Effect of physical activation/surface functional groups on wettability and electrochemical performance of carbon/activated carbon aerogels based electrode materials for electrochemical capacitors

Polymeric carbon/activated carbon aerogels were synthesized through sol-gel polycondensation reaction followed by the carbonization at 800 °C under Argon (Ar) atmosphere and subsequent physical activation under CO₂ environment at different temperatures with different degrees of burn-off. Significant increase in BET specific surface area (SSA) from 537 to 1775 m²g⁻¹ and pore volume from 0.24 to 0.94 cm³g⁻¹ was observed after physical activation while the pore size remained constant (around 2 nm). Morphological characterization of the carbon and activated carbons was conducted using X-ray diffraction (XRD) and Raman spectroscopy. Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) were used to investigate the effect of thermal treatment (surface cleaning) on the chemical composition of carbon samples.Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were used to analyse the capacitive and resistive behaviour of non-activated/activated/and surface cleaned activated carbons employed as electroactive material in a two electrode symmetrical electrochemical capacitor (EC) cell with 6 M KOH solution used as the electrolyte.CV measurements showed improved specific capacitance (SC) of 197 Fg⁻¹ for activated carbon as compared to the SC of 136 Fg⁻¹ when non-activated carbon was used as electroactive material at a scan rate of 5 mVs⁻¹. Reduction in SC from 197 Fg⁻¹ to 163 Fg⁻¹ was witnessed after surface cleaning at elevated temperatures due to the reduction of surface oxygen function groups.The result of EIS measurements showed low internal resistance for all carbon samples indicating that the polymeric carbons possess a highly conductive three dimensional crosslinked structure. Because of their preferred properties such as controlled porosity, exceptionally high specific surface area, high conductivity and desirable capacitive behaviour, these materials have shown potential to be adopted as electrode materials in electrochemical capacitors.     

Nitrogen-doped hierarchically porous carbon obtained via single step method for high performance supercapacitors

In the present work, nitrogen doped hierarchically activated porous carbon (APC) samples have been synthesized via single step scalable method using ethylene di-amine tetra acetic acid (EDTA) as precursor and KOH as activating agent. Activated porous carbons with different pore sizes have been developed by varying the activation temperature. SEM, TEM and SAXS analysis suggest that with variation of activation temperature, a hierarchical porous structure with interconnected meso-pore and micro pores has been achieved. The sufficiently high surface area of the synthesized materials provides active sites to enhance the diffusion of ions between the electrolyte and the carbon electrodes. The electrode prepared at 800 °C activated sample exhibited highest specific capacitance of 274 Fg^-1 in two electrode setup, at a current density of 0.1 Ag^-1 in 1 M aqueous H₂SO₄. Along with this, it showed maximum energy density of 9.5 Whkg^?1 at a power density of 64.5 Wkg^-1. The remarkable electrochemical performance reveals that the synthesized nitrogen doped activated carbon electrodes derived from EDTA can be tuned to have optimum pore structure and pore size distribution for better electrochemical performance, so it can be considered as a potential electrode material for applications in electrochemical energy storage.     

Binder free and high performance of sputtered tungsten nitride thin film electrode for supercapacitor device

Here, we demonstrates the fabrication of binder free and very efficient supercapacitor electrode based on tungsten nitride (W₂N) thin film on stainless steel (SS) substrate using reactive sputtering technique. W₂N thin film as a working electrode exhibits high specific capacitance (163 F g⁻¹ at 0.5 mA cm⁻² in 1 M H₂SO₄) along with excellent cycling stability. The binder free symmetric supercapacitor (W₂N||W₂N) device delivers a high specific capacitance (80 Fg^-1) and long life span (90.46% capacitance retention after 10,000 cycles) along with high energy (12.92 Whkg⁻¹) and power (∼674 kWkg⁻¹ at 9.36 Whkg⁻¹) densities. These observed excellent electrochemical performances of the present W₂N thin film based supercapacitor device, recommend it as a potential candidate for energy storage applications.     

Biomass-derived graphene-based nanocomposite: A facile template for decoration of ultrathin nickel–aluminum layered double hydroxide nanosheets as high-performance supercapacitors

One promising approach to design of high performance supercapacitors is based on the coupling the conductive porous carbon matrixes and the electroactive components. However, the main challenge to this goal is the maintaining the long cycling life, high power and high energy densities of the related capacitors. Herein, we reported on an electroactive composite based on biomass derived 3D graphene coupled with nickel-aluminum layer double hydroxides for manufacturing a cathode material in a supercapacitor. The electrode exhibits a remarkable specific capacitance of 1390 F g⁻¹ at 1 Ag^-1, and ultrahigh rate capability of 60% from 1 to 30 Ag^-1, as well as excellent cycling stability with a capacitance retention of 92% after 5000 cycles. Furthermore, the electrode was used as the positive electrode against a Vulcan XC-72R as the negative electrode to assemble an asymmetric supercapacitor. The asymmetric supercapacitor device exhibited a maximum energy density of 173 Wh kg⁻¹ and power density of 28.8 kW kg⁻¹ as well as excellent cycling stability of 92% after 5000 cycles. The asymmetric supercapacitor could lighted up LED lamps with different colors more than 24 min. The work showed promising performance of further application in electrochemical devices.     

One-pot sonochemical synthesis of hierarchical MnWO4 microflowers as effective electrodes in neutral electrolyte for high performance asymmetric supercapacitors

In this article, manganese tungstate (MnWO₄) microflowers as electrode materials for high performance supercapacitor applications are prepared by a one-pot sonochemical synthesis. The crystalline structure and morphology of MnWO₄ microflowers are characterized through X-ray diffraction, field emission scanning electron microscopy. The electrochemical properties of the MnWO₄ microflowers are investigated using cyclic voltammograms, galvanostatic charge/discharge and electrochemical impedance spectroscopy. The MnWO₄ microflowers as electrode materials possess a maximum specific capacitance of 324 F g⁻¹ at 1 mA cm⁻² in the potential window from 0 to +1 V and an excellent cycling stability of 93% after 8000 cycles at a current density of 3 mA cm⁻². An asymmetric supercapacitor device is fabricated using the MnWO₄ and iron oxide (Fe₃O₄)/multi-wall carbon nanotube as the positive and negative electrode materials, it can be cycled reversibly at a potential window at 1.8 V. The fabricated ASC device can deliver a high energy density of 34 Wh kg⁻¹ at a power density of 500 W kg⁻¹ with cycling stability of 84% capacitance retained after 3000 cycles. The above results demonstrate that MnWO₄ microflowers can be used as promising high capacity electrode materials in neutral electrolyte for high performance supercapacitors.     

A new Co-ZIF derived nanoporous cobalt-rich carbons with high-potential-window as high-performance electrodes for supercapacitors

In this work, a Co-ZIF material and the derived nanoporous cobalt-rich carbons by direct carbonization of this Co-ZIF material were synthesized and used as electrode materials for supercapacitors. This ZIF material exhibited a high specific capacitance of 160.3 F g⁻¹ at 0.5 A g⁻¹, an excellent rate capability (73.72 F g⁻¹ at 10 A g⁻¹), and a good cycling stability with 100% of its initials specific capacitance after 8000 cycles. In addition, the obtained derived nanoporous carbons displayed ideal capacitor behaviors and were promising electroactive materials for supercapacitors at low current density. The nanoporous carbon obtained at 650 °C possessed a highest specific capacitance of 393 F g⁻¹ at 0.5 A g⁻¹ and a wide potential application range of −1.0–0.33 V. In addition, a symmetric supercapacitor device consisting of Z-C-650 and activated carbon exhibited a maximum energy density of 61.23 Wh Kg⁻¹ at a power density of 700 W kg⁻¹ and predicted that Z-C-650 could be used as a potential energy storage material.     

TiO2 nanorods decorated on RGO sheet for an excellent energy storage performance

Herein, we report nanocomposite of titanium dioxide (TiO₂) nanorods decorated reduced graphene oxide (TiO₂/RGO) nanocomposite prepared using the simple, one-pot hydrothermal route for electrode material in supercapacitor applications. A systematic comparison study was carried out for the TiO₂ nanorods coated on graphite foil in presence of alkaline media 3 M KOH, NaCl, and Na₂SO₄ using the three-electrode method. The TiO₂/RGO composite shows an excellent specific capacitance (C_sp) of 330 Fg^-1 at the discharge current density 0.5 Ag^-1 in presence of 3 M KOH electrolyte solution. The obtained highest specific capacitance values in order by various electrolytes are observed as KOH > NaCl > Na₂SO₄. The long-term cycle stability of charge and discharge cycle at current density 0.5 Ag^-1 over 1000 cycles and only 8% decay in the specific capacitance of TiO₂/RGO nanocomposite was observed in 3 M KOH electrolyte. The improved electrochemical performance TiO₂/RGOcomposite in presence of KOH electrolyte is shown to be the most suitable electrode for the supercapacitors.     

Pinecone biomass-derived activated carbon: the potential electrode material for the development of symmetric and asymmetric supercapacitors

Activated carbon, from biomass (pinecone), was synthesized by conventional pyrolysis/chemical activation process and utilized for the fabrication of supercapacitor electrodes. The pinecone-activated carbon synthesized with 1:4 ratio of KOH (PAC4) showed an increase in surface area and pore density with a considerable amount of oxygen functionalities on the surface. Moreover, PAC4, as supercapacitor electrode, exhibited excellent electrochemical performances with specific capacitance value ∼185 Fg⁻¹ in 1 M H₂SO₄, which is higher than that of nonactivated pinecone carbon and 1:2 ratio KOH-based activated carbon (PAC2) (∼144 Fg⁻¹). The systematic studies were performed to design various forms of devices (symmetric and asymmetric) to investigate the effect of device architecture and operating voltage on the performance and stability of the supercapacitors. The symmetric supercapacitor, designed utilizing PAC4 in H₂SO₄ electrolyte, exhibited a maximum device-specific capacitance of 43 Fg⁻¹ with comparable specific energy/power and excellent stability (∼96% after 10 000 cycles). Moreover, a symmetric supercapacitor was specially designed using PAC4, as a positive electrode, and PAC2, as a negative electrode, under their electrolytic ion affinity, and which operates in aqueous Na₂SO₄ electrolyte for a wide cell voltage (1.8 V) and showed excellent supercapacitance performances. Also, a device was assembled with poly(3,4-ethylene dioxythiophene) (PEDOT) nanostructure, as positive electrode, and PAC4, as a negative electrode, to evaluate the feasibility of designing a hybrid supercapacitor, using polymeric nanostructure, as an electrode material along with biomass-activated carbon electrode.     

Formation of hierarchical 3D cross-linked porous carbon with small addition of graphene for supercapacitors

In the present paper, starch was used as raw material to prepare carbon material with low-temperature hydrothermal route and hierarchical three-dimensional cross-linked porous carbon was successfully synthesized with the help of a small amount of graphene for high-performance supercapacitors. It's found that presence of graphene is a crucial condition for the formation of 3D porous carbon and graphene acts as a skeleton in the porous carbon. This kind of carbon material exhibited very high surface area of 1887.8 m² g⁻¹ and delivered excellent electrochemical performance. Its specific capacitance can reach 141 F g⁻¹ at 0.5 A g⁻¹ and more importantly, after 10,000 cycles 98.6% of initial specific capacitance can be maintained. To explore the practical application of the 3D porous carbon, an asymmetric supercapacitor coin-type device was assembled with 3D porous carbon and graphene as electrode materials in organic electrolyte. The constructed device exhibited high energy density of 48.5 Wh·kg⁻¹ at a power density of 1.5 kW kg⁻¹ and still maintains 39.625 Wh·kg⁻¹ under the high power density (15 kW kg⁻¹). These results will promote the rapid development of 3D porous carbon prepared by low-temperature route and the application in supercapacitors.     

Improving hydrogen evolution reaction and capacitive properties on CoS/MoS2 decorated carbon fibers

We report a facile method to transform abundantly dumped banana stem fibers into carbon fibers (CFs) useful for energy applications. The CFs surface area is increased by varying the quantity of KOH activation to 488 m²g^-1. The solvothermal method is used to synthesize CoS, CoS/MoS₂ and also grown on the activated carbon fibers (ACFs). Nano nodules of CoS arranged into sheets and layers of MoS₂ stacked together were found in FESEM analysis. The morphology of the CoS/MoS₂ differs when grown on ACFs. The growth of CoS/MoS₂ along the ACFs length prevents any stacking of the pseudocapacitance materials. The ternary composite ACFs/CoS/MoS₂ exhibits superior supercapacitor behavior as well as hydrogen evolution reaction (HER) due to the synergetic effect of the conducting ACF surface and redox active CoS/MoS₂. A maximum specific capacitance of 733 Fg^-1, energy and power density of 33 WhKg⁻¹ and 999 WKg^-1 respectively are obtained. A low Tafel slope value of 61 mVdec⁻¹ is obtained for the ACFs/CoS/MoS₂ ternary composite electrode. The present work therefore offers a fresh insight into the effective conversion of waste materials into electrode material for energy storage and conversion applications.     

Interconnected NiS-nanosheets@porous carbon derived from Zeolitic-imidazolate frameworks (ZIFs) as electrode materials for high-performance hybrid supercapacitors

Nickel sulfide-based materials have shown great potential for electrode fabrication owing to their high theoretical specific capacitance but poor conductivity and morphological aggregation. A feasible strategy is to design hybrid structure by introducing highly-conductive porous carbon as the supporting matrix. Herein, we synthesized hybrid composites consisting of interconnected NiS-nanosheets and porous carbon (NiS@C) derived from Zeolitic-imidazolate frameworks (ZIFs) using a facile low-temperature water-bath method. When employed as electrode materials, the as-prepared NiS@C nanocomposites present remarkable electrochemical performance owing to the complex effect that is the combined advantages of double-layer capacitor-type porous carbon and pseudocapacitor-type interconnected-NiS nanosheets. Specifically, the NiS@C nanocomposites exhibit a high specific capacitance of 1827 F g⁻¹ at 1 A g⁻¹, and excellent cyclic stability with a capacity retention of 72% at a very high current density of 20 A g⁻¹ after 5000 cycles. Moreover, the fabricated hybrid supercapacitor delivers 21.6 Wh kg⁻¹ at 400 W kg⁻¹ with coulombic efficiency of 93.9%, and reaches 10.8 Wh kg⁻¹ at a high power density of 8000 W kg⁻¹, along with excellent cyclic stability of 84% at 5 A g⁻¹ after 5000 cycles. All results suggest that NiS@C nanocomposites are applicable to high-performance electrodes in hybrid supercapacitors and other energy-storage device applications.     

Hybrid electrochemical capacitors based on polyaniline and activated carbon electrodes

The performance of a newly designed, polyaniline–activated carbon, hybrid electrochemical capacitor is evaluated. The capacitor is prepared by using polyaniline as a positive electrode and activated carbon as a negative electrode. From a constant charge–discharge test, a specific capacitance of 380 F g⁻¹ is obtained. The cycling behaviour of the hybrid electrochemical capacitor is examined in a two-electrode cell by means of cyclic voltammetry. The cycle-life is 4000 cycles. Values for the specific energy and specific power of 18 Wh kg⁻¹ and 1.25 kW kg⁻¹, respectively, are demonstrated for a cell voltage between 1 and 1.6 V.     

N,P, S co-doped biomass-derived hierarchical porous carbon through simple phosphoric acid-assisted activation for high-performance electrochemical energy storage

Porous carbon materials are the most widely used electrode materials in Electric Double Layer Supercapacitor (EDLS). Optimize specific surface area, improving hierarchical pores structure, and doping heteroatoms are all important methods to improve the capacitance performance of electrodes. Herein, we synthesize walnut shell-derived hierarchical porous carbon (WSPC) with cost-effective and well-developed pore for electrochemical energy storage via simple phosphoric acid-assisted activation method. The final porous carbon products have perfect microporous structure, abundant heteroatom functional groups (the atomic content ratio of nitrogen, phosphorus and sulfur reaches 10.3%), and high specific surface area and pore volume (up to 2583 m² g^?1 and 1.236 cm³ g^?1, respectively). In the three-system, the electrode shows an optimal specific capacitance of up to 332 F g^?1 and excellent rate performance. In the symmetric system, the symmetric device WSPC//WSPC shows a maximum gravimetric specific energy of ~14.08 Wh kg^?1. And the device still has a specific energy of 9.75 Wh kg^?1 even under the high gravimetric specific power of 7 kW kg^?1. In addition, the device has excellent cycle stability and retains an initial specific capacitance of 90.2% after 8000 galvanostatic charge-discharge (GCD) cycle. In summary, these outstanding results suggest the biomass derived porous carbon possessing the potential and will show great commercial value for the fabrication of high performance supercapacitors.     

Enhanced performance of carbon-based supercapacitors by constructing protonic and electric dual-channels in electrodes

Powdery carbonaceous materials have to use binder materials when they are integrated into electrodes for supercapacitors, which will results in high interfacial charge transfer resistances and reduced specific capacitance. To resolve the problem, protonic and electric dual-channels are constructed in electrodes by in situ synthesis of cesium hydrogen salt of phosphotungstic acid on the surface of carbonaceous materials. The cesium hydrogen salt particles are confirmed by a Fourier transform infrared spectroscopy, X-ray diffractometer and an energy dispersive X-ray spectroscopy. The electrochemical properties of as-fabricated electrodes are measured by cyclic voltammetry, galvanostatic charging-discharging, and impedance analysis with an electrochemical workstation. At a current density of 1 A g⁻¹, the electrode shows a specific capacitance of 152 F g⁻¹. Compared to the electrode without the cesium hydrogen salt, the value increases 25% at least. Furthermore, the specific capacitance retention of the electrode reaches 104% of its original capacitance after 5000 charge-discharge cycles, suggesting excellent cycling stability.     

Rational design of hierarchical core-shell structured CoMoO4@CoS composites on reduced graphene oxide for supercapacitors with enhanced electrochemical performance

Engineering multicomponent active materials as an advanced electrode with the rational designed core-shell structure is an effective way to enhance the electrochemical performances for supercapacitors. Herein, three-dimensional self-supported hierarchical CoMoO₄@CoS core-shell heterostructures supported on reduced graphene oxide/Ni foam have been rationally designed and prepared via a facile approach. The unique structure and the synergistic effects between two different materials, as well as excellent electronic conductivity of the reduced graphene oxide, contribute to the increased electrochemically active site and enhanced capacitance. The core-shell CoMoO₄@CoS composite displays the superior specific capacitance of 3380.3 F g⁻¹ (1 A g⁻¹) in the three-electrode system and 81.1% retention of the initial capacitance even after 6000 cycles. Moreover, an asymmetric device was successfully prepared using CoMoO₄@CoS and activated carbon as positive/negative electrodes. It is worth mentioning that the device delivered the high energy density of 59.2 W h kg⁻¹ at the power density of 799.8 W kg⁻¹ and the excellent cycle performance (about 91.5% capacitance retention over 6000 cycles). These results indicate that the core-shell CoMoO₄@CoS composites offers the novelty strategy for preparation of electrodes for energy conversion and storage devices.     

Naturally occurring neem gum: An unprecedented green resource for bioelectrochemical flexible energy storage device

Naturally available neem tree gum consisting of bioelectrolyte and bioelectrode was fabricated for flexible energy storage device. Structural morphology, thermal stability, porosity and surface area of as prepared bioelectrode were characterized thoroughly by using scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and Brunauer–Emmett–Teller (BET) isotherm respectively. The bioelectrolyte conductivity was optimized under various concentrations of lithium ion salts and temperatures through electrochemical impedance spectroscopy (EIS). A flexible supercapacitor (SCs) was fabricated by using bioelectrodes and electrolyte and tested for its electrochemical properties. The supercapacitor displayed specific capacitance of 640 Fg^-1 and 200 Fg^-1 at a current density 0.5 Ag^-1 and 1.0 V operating potential window. The energy device has also demonstrated large operational window (2.0 V) and shown 102 Fg^-1 at a current density of 1.0 Ag^-1. The novelty of the present work lies in the simplified, cost-effective procedure for preparation of biomaterials, their remarkably high stability under strong mechanical bent and long-term charging-discharging cycles of the fabricated device.     

Self-assembly of novel cobalt iron phosphate nanoparticles for the solid-state supercapattery and high-performance hydrogen evolution reaction

In this article, we report the preparation of novel cobalt iron phosphate nanoparticles which are self-assembled for energy storage, energy conversion, and sustainability. The self-assembled nanoparticles provide an efficient pathway for the transfer of electrons from the bulk of the materials to the interface of the electrode. This hypothesis has been derived from the analysis based on the electrochemical results for the supercapacitor-based energy storage and hydrogen evolution. The electrode consisting of self-assembled nanoparticles exhibits a maximum specific capacity of 280 C g⁻¹ at a specific current of 1 A g⁻¹. The cyclic voltammetric results suggest the prominent charge storage is by the faradaic reaction which has been concluded from Dunn's approach. The supercapattery device utilizing activated carbon (AC) as the negative electrode and cobalt iron phosphate as the positive electrode exhibit a specific capacity of 210 C g⁻¹ at 2 A g⁻¹ while the specific energy of 47.6 Wh kg^-1 at 1.6 kW kg⁻¹. Furthermore, the electrode actively catalyzes the electrochemical hydrogen evolution reaction and it can be lowering the overpotential required by the hydrogen generation. It exhibits the overpotential of 197 mV while the electrode represents the long-time (24 h) consistency for hydrogen production. These results indicate that the novel cobalt iron phosphate nanoparticles could be a potential candidate for energy storage and conversion purposes.     

Polyaniline-Acetylene black-Copper cobaltite based ternary hybrid material with enhanced electrochemical properties and its use in supercapacitor electrodes

A new system based on Polyaniline-Acetylene black-Copper cobaltite composite has been prepared and affirmed by XRD, UV, SEM, FTIR, and EDS characterizations. The rod-like texture of ternary hybrid system offered excellent electrochemical activity in comparison to single and binary systems. CV and CD results revealed outstanding redox behavior of the ternary hybrid electrodes. Ternary electrode (PACC) presented the highest specific capacitance value of 690 F/g at 1 mA/cm² current density. PACC electrode based symmetric supercapacitor had a specific capacitance of 137.25 Fg^-1 at 1 mA/cm² of current density. PACC symmetric supercapacitor had the highest specific power and specific energy of 3308.85 W.kg^-1 and 19.064 Wh.kg^-1, respectively. The ternary system provides less charge transfer resistance values compared to all other systems. Thermal stability of the ternary composite is way better than polyaniline, which is due to the contribution of copper cobaltite and acetylene black. The overwhelming characteristics of the ternary hybrid composite bring it to the limelight as an excellent candidate in the field of supercapacitors.     

Electrochemical profile of nano-particle CoAl double hydroxide/active carbon supercapacitor using KOH electrolyte solution

A nano-structured CoAl double hydroxide with an average particle size of 60–70 nm was prepared by a chemical co-precipitation. It was used as a positive electrode for the asymmetric hybrid supercapacitor in combination with an active carbon negative electrode in KOH electrolyte solution. The electrochemical capacitance performance of this kind of hybrid supercapacitor was investigated by means of cyclic voltammetry, electrochemical impedance spectroscopy and galvanostatic charge–discharge tests. A specific capacitance of 77 F g⁻¹ with a specific energy density of 15.5 wh kg⁻¹ was obtained for the hybrid supercapacitor within the voltage range of 0.9–1.5 V. The supercapacitor also exhibits a good cycling performance and keep 90% of initial capacity over 1000 cycles.     

Facile one pot sonochemical synthesis of CoFe2O4/MWCNTs hybrids with well-dispersed MWCNTs for asymmetric hybrid supercapacitor applications

In this study, a facile sonochemical strategy is used for the fabrication of CoFe₂O₄/MWCNTs hybrids as an electrode material for supercapacitor applications. FE-SEM image demonstrates the uniformly well-distributed MWCNTs as well as porous structures in the prepared CoFe₂O₄/MWCNTs hybrids, suggesting 3D network formation of conductive pathway, which can enhance the charge and mass transport properties between the electrodes and electrolytes during the faradic redox reactions. The as-fabricated CoFe₂O₄/MWCNTs hybrids with the MWCNTs concentration of 15 mg (CFC15) delivers maximum specific capacitance of 390 F g⁻¹ at a current density of 1 mA cm⁻², excellent rate capability (275 F g⁻¹ at 10 mA cm⁻²), and outstanding cycling stability (86.9% capacitance retention after 2000 cycles at 3 mA cm⁻²). Furthermore, the electrochemical performance of the CFC15 is superior to those of pure CoFe₂O₄ and other CoFe₂O₄/MWCNTs hybrids (CFC5, CFC10 and CFC20), indicating well-dispersion MWCNTs and uniform porous structures. Also, as-fabricated asymmetric supercapacitor device using the CoFe₂O₄/MWCNTs hybrids as the positive electrode and activated carbon as the negative electrode materials shows the outstanding supercapacitive performance (high specific capacitance, superior cycling stability and good rate capability) for energy storage devices. It delivers a capacitance value of 81 F g⁻¹ at 3 mA cm⁻², ca. 92% retention of its initial capacitance value after 2000 charge-discharge cycles and excellent energy density (26.67 W h kg⁻¹) at high power density (~319 W kg⁻¹).