Fatigue crack growth for a surface crack in a round bar under multi-axial loading condition

In this paper, the fatigue life, surface crack extension direction and crack growth rate in an elastic bar with a circular cross section are determined through experiments under cyclic torsion with axial static and cyclic tension/compression loading. The effects of the loading type, loading value and stress ratio on the crack growth behaviour are discussed. The results show that, under pure fatigue torsion loading, the crack extension direction is almost the same whatever the value of torsion loading. Under fatigue torsion with cyclic tension loading, it is found that the crack extension direction is mainly determined by the alternating parts of the stresses and is almost independent of the average parts of the stresses, whereas the fatigue life is obviously dependent on the average stress.     

Crack growth mechanism in precracked torsional fatigue specimens

The mechanism of crack growth of precracked materials was investigated under cyclic torsion loading with and without axial static stress using 4340 steel. During the crack growth, branching of the crack was observed. The length of the crack between the first branching points was dependent on loading conditions. This length was longer when the applied shear amplitude and the static axial stress level were higher. When the crack tips were opened by the tension loads, the crack had the tendency to grow in a shear mode during cyclic torsion. It was found that friction of the crack surfaces prevented shear mode crack growth. Furthermore, at higher stresses the initiation of new microcracks was observed in front of the main crack and their density was dependent on loading conditions. This helped the crack grow in a shear mode before and after branching.     

Very high cycle fatigue of VDSiCr spring steel under torsional and axial loading

Very high cycle fatigue (VHCF) properties of VDSiCr spring steel are investigated with ultrasonic equipment under fully reversed cyclic torsion loading and under cyclic axial loading at load ratios R = –1, R = 0.1 and R = 0.5. Shot‐peened specimens with surface finish similar to valve springs in combustion engines are tested until limiting lifetimes of 10¹⁰ cycles. Under cyclic torsion loading, specimens either fail below 10⁶ cycles with crack initiation at the surface or they do not fail. Under cyclic axial loading, failures above 10⁹ cycles were found for all load ratios with crack initiation at the surface or at internal inclusions. Ratio of mean endurance limit (50% failure probability at 10¹⁰ cycles) under fully reversed cyclic torsion and cyclic tension‐compression loading is 0.86. Cyclic torsion loading slightly below the endurance limit leads to cyclic softening first followed by cyclic hardening whereas cyclic stability is found for tension‐compression loading. Cyclic torsion reduces surface compression stresses whereas they are hardly affected by cyclic tension‐compression loading. Mean endurance limit at 10¹⁰ cycles for R = 0.1 is 61% of the endurance stress amplitude at load ratio R = –1, and for R = 0.5 it is 44% of the tension‐compression endurance limit. Endurance limits for cyclic torsion and cyclic tension‐compression loading are comparable, if effective stress amplitude is used that considers cyclic normal stresses and residual compression stresses at the surface.     

Behaviour of short cracks in alloy 800HT under biaxial fatigue

Biaxial in phase fatigue tests were carried out on thin walled tube specimens of alloy 800HT at ambient temperature. The loading modes included tension, torsion, and combined tension—torsion with a tensile/shear plastic strain range ratio Δ?p/Δγp = 3^1/2. The influence of effective strain amplitudes and biaxiality on the initial growth of fatigue cracks was investigated using the replica technique. The results indicated that the loading conditions strongly affected the growth rates of short cracks. In torsion the cracks grew significantly more slowly than under axial or biaxial loading. A mean tensile stress perpendicular to the shear crack promoted its growth and reduced the fatigue life. The growth of the cracks could be described by the ΔJ integral for axial and biaxial loading; the integration predicted the fatigue life under axial and biaxial loading correctly. However, significantly conservative lifetime predictions were obtained for pure torsional loading since ΔJ does not include crack closure and crack surface rubbing.

MST/3234     

Biaxial fatigue for proportional and non‐proportional loading paths

In order to study the use of a local approach to predict crack‐initiation life on notches in mechanical components under multiaxial fatigue conditions, the study of the local cyclic elasto‐plastic behaviour and the selection of an appropriate multiaxial fatigue model are essential steps in fatigue‐life prediction. The evolution of stress–strain fields from the initial state to the stabilized state depends on the material type, loading amplitude and loading paths. A series of biaxial tension–compression tests with static or cyclic torsion were carried out on a biaxial servo‐hydraulic testing machine. Specimens were made of an alloy steel 42CrMo4 quenched and tempered. The shear stress relaxations of the cyclic tension–compression with a steady torsion angle were observed for various loading levels. Finite element analyses were used to simulate the cyclic behaviour and good agreement was found. Based on the local stabilized cyclic elastic–plastic stress–strain responses, the strain‐based multiaxial fatigue damage parameters were applied and correlated with the experimentally obtained lives. As a comparison, a stress‐invariant‐based approach with the minimum circumscribed ellipse (MCE) approach for evaluating the effective shear stress amplitude was also applied for fatigue life prediction. The comparison showed that both the equivalent strain range and the stress‐invariant parameter with non‐proportional factors correlated well with the experimental results obtained in this study.     

A computational strategy for damage‐tolerant design of hollow shafts under mixed‐mode loading condition

Three‐dimensional numerical analyses, using the finite element method (FEM), have been adopted to simulate fatigue crack propagation in a hollow cylindrical specimen, under pure axial or combined axial‐torsion loading conditions. Specimens, made of Al alloys B95AT and D16T, have been experimentally tested under pure axial load and combined in‐phase constant amplitude axial and torsional loadings. The stress intensity factors (SIFs) have been calculated, according to the J‐integral approach, along the front of a part through crack, initiated in correspondence of the outer surface of a hollow cylindrical specimen. The crack path is evaluated by using the maximum energy release rate (MERR) criterion, whereas the Paris law is used to calculate crack growth rates. A numerical and experimental comparison of the results is presented, showing a good agreement in terms of crack growth rates and paths.     

Shear mode fatigue crack growth in 1050 aluminium

The shear mode crack growth mechanism in 1050 aluminium was investigated using pre‐cracked specimens. A small blind hole was drilled in the centre section of the specimens in order to predetermine the crack initiation position, and a push–pull fatigue test was used to make a pre‐crack. Crack propagation tests were carried out using both push–pull and cyclic torsion with a static axial load. With push–pull testing, the main crack grew by a mixed mode. It is thus apparent that shear deformation affects the fatigue crack growth in pure aluminium. In tests using cyclic torsion, the fatigue crack grew by a shear mode. The micro‐cracks initiated perpendicular and parallel to the main crack's growth direction during the cyclic torsion tests. However, the growth direction of the main crack was not changed by the coalescence of the main crack and the micro‐cracks. Shear mode crack growth tends to occur in aluminium. The crack growth behaviour is related to a material's slip systems. The number of slip planes in aluminium is smaller than that of steel and the friction stress during edge dislocation motion of aluminium is lower than many other materials. Correlation between the crack propagation rate and the stress intensity factor range was almost the same in both push–pull and cyclic torsion with tension in this study.     

Stress intensity factors for surface fatigue crack in a round bar under cyclic axial loading

In this paper, the surface fatigue crack growth shape for an initial straight-fronted edge crack in an elastic bar of circular cross-section is determined through experiments under pure fatigue axial loading. Three different initial notch depths are discussed. The relations of the aspect ratio (b/c) and relative crack depth (b/D) are obtained, and it is shown that there is a great difference in the growth of cracks with different initial front shapes and crack depths. Further, using the three-dimensional finite element method, the stress intensity factors (SIFs) are determined under remote uniform tension loading. Since the relationship of b/c and b/D changes during the fatigue crack growth, the SIFs are determined for different surface crack configurations.     

A crack in a linear-elastic material under mode II loading, revisited

A sharp crack in a two-dimensional infinite linear-elastic material, under pure shear (mode II) loading is re-examined. Several criteria have been proposed for the prediction of the onset and direction of crack extension along a path emanating from the tip of the initial crack. These criteria date back some three decades and are well documented in the literature. All the predictions from the different criteria are close and indicate that the crack extension takes a direction at an angle of ≈ −70° measured counterclockwise from the positive x -axis, in the case of a remotely applied positive shear stress. However, the possibility seems to have been overlooked that the crack extension may initiate not from the crack tip itself, but instead may initiate on the free surface at an infinitesimal distance behind the crack tip. The effect of crack tip plasticity on the relevant stresses in the region of the crack tip is investigated by the application of an elastic–plastic finite element program.     

A notch strain calculation of a notched specimen under axial-torsion loadings

In this paper, a notch analysis model is presented for the numerical prediction of multiaxial strains of a notched 1070 steel specimen under combined axial and torsion loadings. The proposed model is based on the notion of a structural yield surface and uses a small-strain cyclic plasticity model to describe stress–strain relations. A notch load–strain curve is calculated with Neuber’s rule and incremental nonlinear finite element analysis. The presented model is applied to simulate the notch root deformations of a circumferentially notched specimen under cyclic tension–compression–torsion loading histories. The model predictions are evaluated with strain measurements at the notch root of the specimen in a comprehensive set of cyclic tests. The computed strain loops were in accord with experimental data and matched qualitatively with measured shear–axial strain histories irrespective of loading path of the test. In proportional balanced torsion-axial loading, the nonlinear shear strain–axial strain loops were calculated properly. The modeling errors were determined to be a function of the loading path shape, and compared to shear strains, axial strain predictions were more accurate.     

Analytical and experimental studies on fatigue crack path under complex multi-axial loading

In real engineering components and structures, many accidental failures are due to unexpected or additional loadings, such as additional bending or torsion, etc. Fractographical analyses of the failure surface and the crack orientation are helpful for identifying the effects of the non‐proportional multi‐axial loading. There are many factors that influence fatigue crack paths. This paper studies the effects of multi‐axial loading path on the crack path. Two kinds of materials were studied and compared in this paper: AISI 303 stainless steel and 42CrMo4 steel. Experiments were conducted in a biaxial testing machine INSTRON 8800. Six different biaxial loading paths were selected and applied in the tests to observe the effects of multi‐axial loading paths on the additional hardening, fatigue life and the crack propagation orientation. Fractographic analyses of the plane orientations of crack initiation and propagation were carried out by optical microscope and SEM approaches. It was shown that the two materials studied had different crack orientations under the same loading path, due to their different cyclic plasticity behaviour and different sensitivity to non‐proportional loading. Theoretical predictions of the damage plane were made using the critical plane approaches such as the Brown–Miller, the Findley, the Wang–Brown, the Fatemi–Socie, the Smith–Watson–Topper and the Liu's criteria. Comparisons of the predicted orientation of the damage plane with the experimental observations show that the critical plane models give satisfactory predictions for the orientations of early crack growth of the 42CrMo4 steel, but less accurate predictions were obtained for the AISI 303 stainless steel. This observation appears to show that the applicability of the fatigue models is dependent on the material type and multi‐axial microstructure characteristics.     

在多轴载荷下45钢的循环特性

通过多轴疲劳试验，研究了在多轴加载条件下45钢的循环特性变化规律，分析了非比例附加强化、多轴循环软化/硬化特性及疲劳寿命对加载路径参数的依赖性，结果表明，相位角主要影响非比例附加强化程度，幅值比主要影响多轴循环软化/硬化特性，二者都影响多轴疲劳寿命。     

Fatigue behaviour and life prediction of fibre reinforced metal laminates under constant and variable amplitude loading

ABSTRACT Fatigue crack growth of fibre reinforced metal laminates (FRMLs) under constant and variable amplitude loading was studied through analysis and experiments. The distribution of the bridging stress along the crackline in centre‐cracked tension (CCT) specimen of FRMLs was modelled numerically, and the main factors affecting the bridging stress were identified. A test method for determining the delamination growth rates in a modified double cracked lap shear (DCLS) specimen was presented. Two models, one being fatigue‐mechanism‐based and the other phenomenological, were developed for predicting the fatigue life under constant amplitude loading. The fatigue behaviour, including crack growth and delamination growth, of glass fibre reinforced aluminium laminates (GLARE) under constant amplitude loading following a single overload was investigated experimentally, and the mechanisms for the effect of a single overload on the crack growth rates and the delamination growth rates were identified. An equivalent closure model for predicting crack‐growth in FRMLs under variable amplitude loading and spectrum loading was presented. All the models presented in this paper were verified by applying to GLARE under constant amplitude loading and Mini‐transport aircraft wing structures (TWIST) load sequence. The predicted crack growth rates are in good agreement with test results.     

EFFECT OF BIAXIAL MEAN STRESS ON CYCLIC STRESS-STRAIN RESPONSE AND BEHAVIOUR OF SHORT FATIGUE CRACKS IN A HIGH STRENGTH SPRING STEEL

Abstract— Biaxial fatigue tests were conducted on a high strength spring steel using hour-glass shaped smooth specimens. Four types of loading system were employed, i.e. (a) fully reversed cyclic torsion, (b) uniaxial push—pull, (c) fully reversed torsion with a superimposed axial static tension or compression stress, and (d) uniaxial push—pull with a superimposed static torque, to evaluate the effects of mean stress on the cyclic stress—strain response and short fatigue crack growth behaviour. Experimental results indicate that a biaxial mean stress has no apparent influence on the stress—strain response in torsion, however a superimposed tensile mean stress was detrimental to torsional fatigue strength. Similarly a superimposed static shear stress reduced the push—pull fatigue lifetime. A compressive mean stress was seen to be beneficial to torsion fatigue life. The role of mean stress on fatigue lifetime, under mixed mode loading, was investigated through experimental observations and theoretical analyses of short crack initiation and propagation. Using a plastic replication technique the effects of biaxial mean stress on both Stage I (mode II) and Stage II (mode I) short cracks were evaluated and analysed in detail. A two stage biaxial short fatigue crack growth model incorporating the influence of mean stress was subsequently developed and applied to correlate data of crack growth rate and fatigue life.     

Surface flaws behavior under tension,bending and biaxial cyclic loading

Fatigue surface crack growth and in-plane and out-of-plane constraint effects are studied through experiments and computations for the aluminum alloy D16T. A tension/bending central notched plate and cruciform specimens under different biaxial loadings with external semi-elliptical surface cracks are studied. The variation of the fatigue crack growth rate and surface crack paths is studied under cyclic tension, bending and biaxial tension–compression loading. For the experimental surface crack paths in the tested specimens, the T-stress, out-of-plane T_z factor, local triaxiality parameter h and the governing parameter for the 3D-fields of the stresses and strains at the crack tip in the form of the I_n-integral are calculated as a function of the aspect ratio by finite element analysis to characterize the constraint effects along the semi-elliptical crack front. The plastic stress intensity factor approach is applied to the fatigue crack growth on the free surface, as well as at the deepest point of the semi-elliptical surface crack front, of the tested tension/bending plate and cruciform specimens. From the results, characteristics of the fatigue surface crack growth rate as a function of the loading conditions are established.     

Fatigue crack growth of filled rubber under constant and variable amplitude loading conditions

Service conditions experienced by rubber components often involve cyclic loads which are more complex than a constant amplitude loading history. Consequently, a model is needed for relating the results of constant amplitude characterization of fatigue behaviour to the effects of variable amplitude loading signals. The issue is explored here via fatigue crack growth experiments on pure shear specimens conducted in order to evaluate the applicability of a linear crack growth model equivalent to Miner's linear damage rule. This model equates the crack growth rate for a variable amplitude signal to the sum of the constant amplitude crack growth rates associated with each individual cycle. The variable amplitude signals were selected to show the effects of R-ratio (ratio of minimum to maximum energy release rate), load level, load sequence, and dwell periods on crack growth rates. In order to distinguish the effects of strain crystallization on crack growth behaviour, two filled rubber compounds were included: one that strain crystallizes, natural rubber, and one that does not, styrene-butadiene rubber. The linear crack growth model was found to be applicable in most cases, but a dwell effect was observed that is not accounted for by the model.     

Crack initiation and propagation in torsional fatigue of circumferentially notched steel bars

Circumferentially notched bars of austenitic stainless steel, SUS316L, and carbon steel, SGV410, with three different notch-tip radii were fatigued under cyclic torsion without and with static tension. The torsional fatigue life of SUS316L was found to increase with increasing stress concentration under the same nominal shear stress amplitude. Electrical potential monitoring revealed that the crack initiation life decreased with increasing stress concentration, while the crack propagation life increased. This anomalous notch-strengthening effect was ascribed to the larger retardation of fatigue crack propagation by sliding contacts of fracture surfaces. The superposition of static tension on cyclic torsion causes notch weakening. The notch-strengthening effect in torsional fatigue was not found in carbon steels, SGV410. The difference in the crack path of small cracks near notch root between stainless steel and carbon steel gives rise to the difference in the notch effect in torsional fatigue. The factory-roof shape observed on fracture surfaces of SUS316L became finer with higher stress amplitude and for sharper notches. The superposition of static tension makes the factory-roof shape less evident. Under higher stresses, the fracture surface was smeared to be flat. The fracture surfaces of SGV410 became smoother with increasing stress amplitude and notch acuity. The three-dimensional feature of fracture surfaces clearly showed the difference of the topography of fracture surfaces. The topographic feature was closely related to the amount of retardation of crack propagation due to the sliding contact of fracture surfaces.     

Threshold stress intensity factor and crack growth rate prediction under mixed-mode loading

A new mixed-mode threshold stress intensity factor is developed using a critical plane-based multiaxial fatigue theory and the Kitagawa diagram. The proposed method is a nominal approach since the fatigue damage is evaluated using remote stresses acting on a cracked component rather than stresses near the crack tip. An equivalent stress intensity factor defined on the critical plane is proposed to predict the fatigue crack growth rate under mixed-mode loading. A major advantage is the applicability of the proposed model to many different materials, which experience either shear or tensile dominated crack growth. The proposed model is also capable to nonproportional fatigue loading since the critical plane explicitly considers the influence of the load path. The predictions of the proposed fatigue crack growth model under constant amplitude loading are compared with a wide range of fatigue results in the literature. Excellent agreements between experimental data and model predictions are observed.     

Mixed-mode fatigue crack growth under biaxial loading

Studies on crack growth in a panel with an inclined crack subjected to biaxial tensile fatigue loading are presented. The strain energy density factor approach is used to characterize the fatigue crack growth. The crack growth trajectory as a function of the initial crack angle and the biaxiality ratio is also predicted. The analysis is applied to 7075-T6 aluminium alloy to predict the dependence of crack growth rate on the crack angle. The effect of crack angle on the cyclic life of the component and on the cyclic life ratio is presented and discussed.