纳米晶钨基重合金粉末的注射成型与固相烧浇

采用高能球磨技术制备了90W-7Ni-3Fe(质量分数,%)纳米晶钨基重合金粉末,研究了该粉末的注射成型和烧结行为,并与传统混合粉末进行了比较.结果表明,机械球磨可以有效地增加粉末喂料的固体粉末含量,改善粉末料的均匀性,并可促进固相烧结的致密化.纳米粉末注射成形坯在1300～1450℃进行固相烧结后,可得到近全致密(＞99%),晶粒细(3～5μm)、拉伸强度高(≥1130MPa)和几乎无变形的重合金样品.     

烧结TiH_2粉末制备钛合金的工艺及组织EI北大核心CSCD

以TiH2粉末为原料,通过组元球磨混合、压制成形和烧结工艺制备钛合金。用扫描电镜对球磨过程TiH2粉末的粒度、形貌变化以及烧结CP-Ti,Ti-6Al-4V合金的组织形貌进行了观察;采用热重分析方法研究了TiH2粉末脱氢的特性;用热膨胀技术研究了TiH2,TiH2-Al-V两种粉末压坯的烧结致密化特性。结果表明:TiH2粉末经过球磨后迅速变细,其粒度随球磨时间的延长而减小,粉末形貌由原来的不规则形状逐渐变为等轴状;TiH2粉末在烧结过程的脱氢将使α-Ti产生强烈收缩、同时因脱氢后获得的新鲜钛表面所发生的快速粘接而使烧结体迅速致密、得到相对密度大于99%的烧结坯体;TiH2-Al-V粉末压坯在烧结时因为伴随着合金元素的溶解而使其烧结致密特性不如纯TiH2粉末压坯的好;TiH2粉末经过成型、烧结脱氢工艺可获得典型的等轴状纯钛组织,TiH2-Al-V粉末经过相同工艺可获得典型的层片状α+β钛合金组织、且合金元素分布均匀。     

Mo-8wt%Cu纳米复合粉末的烧结与加工

用机械合金化法制取Mo-8%Cu(质量分数)纳米复合粉末,采用液相烧结和致密化后处理工艺制备了Mo-8%Cu(质量分数)合金。通过扫描电镜对Mo-Cu液相烧结和变形加工后合金显微组织进行了分析,研究了各种工艺参数对Mo-Cu合金致密性、拉伸强度、延伸率和晶粒尺寸的影响。结果表明,高能球磨的Mo-8%Cu(质量分数)纳米复合粉末坯体,经液相烧结后,其烧结态为Mo、Cu复合网状组织,可获得相对密度高达98.6%的Mo-Cu合金,再经静液挤压变形加工处理后,可获得全致密的Mo-8%Cu(质量分数)合金,在室温静液挤压40%形变率的条件下,拉伸强度可达到576MPa,延伸率5.8%。     

Y-α/β-sialon的气压烧结

研究了Ｓｉ３Ｎ４粉末粒度分析发现相组成,ＡｌＮ粉末的粒度及分阶段烧工艺对气压烧结α／βｓｉａｌｏｎ的致密化,产物相组成和力学性能的影响,采用三阶段保温烧结（１７００℃,１ｈ,１８００℃,１ｈ及１９５０℃,１５ｈ）减少了Ｓｉ３Ｎ４与液相在高温反应促进了材料致密,适当的烧结工艺下及用适当的埋粉,细ＡｌＮ原料有利于材料致密。细Ｓｉ３Ｎ４原料（０．３μｍ）中氧杂质增加导致复合材料中α－ｓｉａｌｏｎｓ相减少     

纳米晶Sm_2Co_(17)型块体永磁的制备及磁性能

制备了两种2∶17R型Sm-Co合金:Sm2(Fe,Cu,Zr,Co)17和纯二元Sm2Co17,并利用高能球磨和放电等离子烧结(SPS)制备了致密的纳米晶块体合金,研究了其磁性能和相结构的变化。Sm2(Fe,Cu,Zr,Co)17具有较高的矫顽力,而纯二元Sm2Co17矫顽力基本为零。但高能球磨可快速降低Sm2(Fe,Cu,Zr,Co)17合金的矫顽力。利用放电等离子烧结非晶粉末制备了纳米晶块体合金,纯二元Sm2Co17合金具有较高的矫顽力,并且具有1∶7H相结构。而Sm2(Fe,Cu,Zr,Co)17合金则因为Fe-Co相及Sm2O3相的析出,具有较高的饱和磁化强度和极低的矫顽力。     

TiAl纳米合金的机械活化-放电等离子原位烧结

（Ti-50％（原子分数）AD-10％Al2O3粉体经过球磨的机械活化（MA）后，用放电等离子烧结（SPS）工艺，在烧结的同时进行固化。采用机械活化-放电等离子烧结（MA—SPS）的方法原位烧结制备TiAl—Al2O3块体纳米材料。球磨前后，（Ti-50％（原子分数）AD-10％Al2O3粉体的衍射图（XRD）相似。MA后得到晶粒度〈25nm的纳米粉体，其中Al2O3起到机械活化和细化晶粒的作用，促使粉体快速纳米化。纳米粉体在温度低于800℃、烧结时间〈5min的烧结参数下，烧结成TiAl纳米合金。TiAl纳米合金的微观结构表明，合金有γ-TiAl和α2—Ti3Al双相组织。SPS原位烧结后，得到密度为3．73g／cm^3的（γ＋α2）双相组织，组成相的晶粒度〈130nm。     

机械球磨法制备纳米晶Fe_（73．5）Cu_1Nb_3Si_（13．5）B_9的

对Ｆｅ_（７３．５）Ｃｕ_１Ｎｂ_３Ｓｉ_（１３．５）Ｂ_９成分的母合金进行了机械球磨，并对不同时间的球磨样品进行了Ｘ射线衍射（ＸＲＤ）和Ｍｏｓｓｂａｕｅｒ谱（ＭＳ）的测量，结果表明样品难以完全非晶化，形成了无序的αＦｅ－Ｓｉ固溶体纳米晶，晶粒尺寸在５ｎｍ左右，同时共有一部分富集Ｎｂ，Ｂ元素的界面非晶相。在各种球磨条件下对αＦｅ－Ｓｉ固溶体中的Ｓｉ含量进行了计算。纳米晶Ｆｅ_（７３．５）Ｃｕ_１Ｎｂ_３Ｓｉ_（１３．５）Ｂ_９软磁合金近年来受到了广泛的重视~［１］。这种材料通常是由熔融金属急冷制成非晶薄带，然后在晶化温度以上退火制成，晶化以后在非晶基体上均匀析出１０－２０ｎｍ尺寸的αＦｅ－Ｓｉ固溶体。机械球磨或机械合金化是近些年来发展起来的一种制备亚稳态材料如非晶，纳米晶，准晶等的有效手段，有一定优越性。本文利用机械球磨探讨一种制备纳米晶Ｆｅ_（７３．５）Ｃｕ_１Ｎｂ_３Ｓｉ_（１３．５）Ｂ_９合金粉末的新途径。     

放电等离子烧结Ti-Al系金属间化合物

用机械合金化法(MA)制备了Ti-45% Al纳米晶合金粉末,并对其进行放电等离子烧结(SPS),烧结时间仅为5min.用D-maxIIA型X射线衍射仪、JEM-2000EX型透射电子显微镜对粉末和烧结块体的微观组织及机械性能进行了研究.研究表明:Ti和Al的粉末随着球磨时间的延长,粉末有明显的细化趋势,球磨5h即有非晶产生,球磨20h后得到接近完全非晶相;采用SPS烧结技术,在1200℃下能够制备出较高硬度的TiAl金属间化合物块体材料.     

溶胶—凝胶法制备PCT铁电陶瓷

本文报导了通过溶胶—凝胶法制备Ｐｂ_（１－ｘ）ＣａｘＴｉＯ_３（ｘ＝０．１～０．３）铁电陶瓷原料粉末，所得粉末具有较高的活性、纯度和均匀度。研究了不同掺ＣａＯ量对晶体结构和烧结温度的影响。在ＰＣＴ晶相生成前未发现有烧绿石或其它过渡晶相的出现。使用该粉末通过１０００～１２００℃的烧结过程，所得ＰＣＴ陶瓷可达理论密度的８８～９４％。     

ZrO2（Y2O3）纳米粉在超高压下快速烧结

研究了超高压（５ＧＰａ）、高温（１３５０℃）下烧结的ＺｒＯ２（Ｙ２Ｏ３）纳米材料的结构及相关系。结果表明：水解法制备的纳米（９ｎｍ）２．２Ｙ－ＺｒＯ２粉体经超高压烧结１０ｓ，致密度即达９９．５％以上，晶粒迅速长大达６０ｎｍ。在０￣９９ｓ范围内，随烧结时间延长，２．２Ｙ－ＴＺＰ的ｔ相增加，四方度（ｃ·ａ＾－１）减小，表明Ｙ２Ｏ３固溶进入ＺｒＯ２晶格内。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from