The effect of polypropylene maleic anhydride on polypropylene/(recycled acrylonitrile butadiene rubber)/(sugarcane bagasse) composite

The effect of polypropylene maleic anhydride (PPMAH) on the tensile properties and morphology of polypropylene (PP)/(recycled acrylonitrile butadiene rubber) (NBRr)/(sugarcane bagasse) (SCB) composites has been studied. Six different composites (100/0/10, 80/20/10, 70/30/10, 60/40/10, 50/50/10, and 40/60/10), with fixed 5 wt% of PPMAH compatibilizer and without PPMAH addition, were carried out. The composites were prepared through melt‐mixing technique at 180^oC for 9 min using a rotor speed of 15 rpm. The specimens were analyzed for mechanical properties and examined with scanning electron microscopy. The tensile strength was found to decrease with increasing filler content. However, tensile strength and Young's modulus of the PPMAH compatibilized composites were found to increase, while the elongation at break showed the opposite trend as compared with the control composites. The morphology results support the tensile properties and indicated a better interaction between the SCB filler and PP/NBRr matrices with the presence of PPMAH as a compatibilizer. This is due to the esterification bonding between the SCB filler and PP matrix in the presence of PP/NBRr matrices. J. VINYL ADDIT. TECHNOL., 23:228–233, 2017. © 2015 Society of Plastics Engineers     

Modification of oil palm empty fruit bunches with maleic anhydride: The effect on the tensile and dimensional stability properties of empty fruit bunch/polypropylene composites

Oil palm empty fruit bunch (EFB)‐filled polypropylene (PP) composites were produced. The EFB filler was chemically modified with maleic anhydride (MAH). The effects of the filler size and chemical modification of EFBs on the tensile and dimensional stability properties of EFB–PP composites were studied. The composites with MAH‐treated EFBs showed higher tensile strengths than those with untreated EFBs. This was attributed to the enhanced compatibility between the MAH‐treated EFBs and PP matrix, as shown in a scanning electron microscopy study. Fourier transform infrared analysis showed evidence of C?C and C?O bonds from MAH at 1630 and 1730 cm^?1, respectively. The MAH‐treated PP composites showed lower water absorption and thickness swelling than those with untreated EFBs. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 827–835, 2003     

Melting and crystallization behaviors,morphology, and mechanical properties of β‐polypropylene/polypropylene‐graft‐maleic anhydride/calcium sulfate whisker composites

The melting and crystallization behaviors, morphology, and mechanical properties of polypropylene (PP)/surface‐treated calcium sulfate (CaSO₄) whisker (T‐CSW), β‐PP/T‐CSW, and β‐PP/polypropylene‐graft‐maleic anhydride (PP‐g‐MAH)/T‐CSW composites had been investigated via differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), polarized light microscopy (PLM), scanning electron microscopy (SEM), and mechanical tests. We found that T‐CSW was an α‐nucleating agent and increased the crystallization temperatures of PP, but PP‐g‐MAH and high loadings of T‐CSW had weakly negative effects on the crystallization rates of PP. The T‐CSW restrained the formation of β‐spherulites, and the spherulitic size decreased in the composites. PP‐g‐MAH improved the compatibility and adhesion between T‐CSW and the matrix. The notched impact strength was improved, and the tensile strength was enhanced at low levels of T‐CSW, while the flexural modulus was weakened for β‐PP/T‐CSW and β‐PP/PP‐g‐MAH/T‐CSW composites versus PP/T‐CSW composites. POLYM. COMPOS., 37:2121–2132, 2016. © 2015 Society of Plastics Engineers     

Effect of maleic anhydride/vinyltrimethoxysilane‐co‐grafting polypropylene on the properties of wood‐flour/polypropylene composites by electron‐beam preirradiation

The electron‐beam preirradiation and reactive extrusion technologies were used to prepare maleic anhydride (MAH)/vinyltrimethoxysilane (VTMS)‐co‐grafting polypropylene (PP) as a high‐performance compatibilizer for wood‐flour/PP composites. The grafting content, chemical structure, and crystallization behavior of the compatibilizers were characterized through Fourier transform infrared spectroscopy, differential scanning calorimetry, and an extraction method. The effects of the compatibilizers on the mechanical properties, water absorption, morphological structure, and torque rheological behavior of the composites were investigated comparatively. The experimental results demonstrate that MAH/VTMS‐g‐PP markedly enhanced the mechanical properties of the composites. Compared with MAH‐g‐PP and VTMS‐g‐PP, MAH/VTMS‐g‐PP clearly showed synergistic effects on the increasing mechanical properties, water absorption, and compatibility of the composites. Scanning electron microscopy further confirmed that the adhesion and dispersion of wood flours in the composites were effectively improved by MAH/VTMS‐g‐PP. These results were also proven by the best water resistance of the wood‐flour/PP composites with MAH/VTMS‐g‐PP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Crystallization behavior of carbon black‐filled polypropylene and polypropylene/epoxy composites

The crystallization behavior of polypropylene (PP)/carbon black (CB) and PP/epoxy/CB composites was studied with differential scanning calorimetry (DSC). The effects of compatibilizer MAH‐g‐PP and dynamic cure on the crystallization behavior are investigated. The nonisothermal crystallization parameters analysis showed that CB particles in the PP/CB composites and the dispersed epoxy particles in the PP/epoxy composites could act as nucleating agents, accelerating the crystallization of the composites. Morphological studies indicated that the incorporation of CB into PP/epoxy resulted in its preferential localization in the epoxy resin phase, changing the spherical epoxy particles into elongated structure, and thus reduced the nucleation effect of epoxy particles. Addition of MAH‐g‐PP significantly decreased the average diameter of epoxy particles in the PP/epoxy and PP/epoxy/CB composites, promoting the crystallization of PP more effectively. The isothermal crystallization kinetics and thermodynamics of the PP/CB and PP/epoxy/CB composites were studied with the Avrami equation and Hoffman theory, respectively. The Avrami exponent and the crystallization rate of the PP/CB composites were higher than those of PP, and the free energy of chain folding for PP crystallization decreased with increasing CB content. Addition of MAH‐g‐PP into the PP/epoxy and PP/epoxy/CB composites increased the crystallization rate of the composites and decreased the chain folding energy significantly. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 104–118, 2006     

Preparation and characterization of nanoclay‐filled polyurethane/polypropylene blends

Ester‐based thermoplastic polyurethane (TPU) nanocomposites were prepared by melt blending at 190°C, using 3 wt% Cloisite 10A (organically modified montmorillonite clay) as the nanoscale reinforcement [TPU(C10A)]. The nanocomposites were subsequently melt‐blended with polypropylene (PP) using maleic anhydride–grafted polypropylene (MA‐g‐PP) as a compatibilizer [in the ratio of 70/30‐TPU/PP, 70/25/5‐TPU/PP/MA‐g‐PP, 70/25/5‐TPU (C10A)/PP/MA‐g‐PP]. Besides giving substantial increase in modulus, tensile strength, and other properties, organoclay reinforcement functions as a surface modifier for TPU hard segment resulting in improved dispersion. The morphology and other characteristics of the nanocomposite blends were investigated in terms of X‐ray diffraction, fourier transform infrared spectroscopy, differential scanning calorimetry, dynamic mechanical analysis, tensile properties, scanning electron microscopy, and atomic force microscopy. The results indicate that the ester‐TPU(C10A)/PP/MA‐g‐PP exhibited better dispersion than other blend systems; abrasion resistance and water absorption resistance were also better for this system. POLYM. ENG. SCI., 50:1878–1886, 2010. © 2010 Society of Plastics Engineers     

Study of dynamically cured PP/MAH‐g‐PP/talc/epoxy composites

In the present study, an epoxy resin was dynamically cured in a polypropylene (PP)/maleic anhydride–grafted PP (MAH‐g‐PP)/talc matrix to prepare dynamically cured PP/MAH‐g‐PP/talc/epoxy composites. An increase in the torque at equilibrium showed that epoxy resin in the PP/MAH‐g‐PP/talc composites had been cured by 2‐ethylene‐4‐methane‐imidazole. Scanning electron microscopy analysis showed that MAH‐g‐PP and an epoxy resin had effectively increased the interaction adhesion between PP and the talc in the PP/talc composites. Dynamic curing of the epoxy resin further increased the interaction adhesion. The dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had higher crystallization peaks than did the PP/talc composites. Thermogravimetric analysis showed that the addition of MAH‐g‐PP and the epoxy resin into the PP/talc composites caused an obvious improvement in the thermal stability. The dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had the best thermal stability of all the PP/talc composites. The PP/MAH‐g‐PP/talc/epoxy composites had better mechanical properties than did the PP/MAH‐g‐PP/talc composites, and the dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had the best mechanical properties of all the PP/talc composites, which can be attributed to the better interaction adhesion between the PP and the talc. The suitable content of epoxy resin in the composites was about 5 wt %. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Effects of clay contents on the dynamic mechanical and rheological properties of polypropylene/MAH‐g‐POE/clay composites

A series of polypropylene/maleic anhydride grafted polypropylene octane elastomer (MAH‐g‐POE)/clay (PPMC) nanocomposites were prepared with a novel compatilizer MAH‐g‐POE and different contents of octadecyl amine modified montmorillonite, and the effects of clay contents on the dynamic mechanical and rheological properties of these PPMC composites were investigated. With clay content increasing, the characteristic X‐ray diffraction peak changed from one to two with intensity decreasing, indicating the decreasing concentration of the intercalated clay layers. The gradual decrease of crystallization temperature of PPMC composites with the increase of clay loading should be attributed to the preferred intercalation of MAH‐g‐POE molecules into clay interlayer during blending, which is also reflected by scanning electron microscopy observations. By evaluating the activation energy for the glass transition process of MAH‐g‐POE and polypropylene (PP) in the PPMC composites, it is found that clay intercalation could cause the restriction effect on the glass transition of both MAH‐g‐POE and PP, and this restriction effect appears stronger for PP and attained the highest degree at 5 wt % clay loading. The melt elasticity of PP could be improved apparently by the addition of MAH‐g‐POE, and 5 wt % clay loading is enough for further enhancing the elastic proportion of PP. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Extrusion foaming behavior of a polypropylene/nanoclay microcellular foam

With maleic anhydride grafted polypropylene (PP‐g‐MAH) as a compatibilizer, composites of block‐copolymerized polypropylene (B‐PP)/nanoclay were prepared. The effects of the PP‐g‐MAH and nanoclay content on the crystallization and rheological properties of B‐PP were investigated. The microcellular foaming behavior of the B‐PP/nanoclay composite material was studied with a single‐screw extruder foaming system with supercritical (SC) carbon dioxide (CO₂) as the foaming agent. The experimental results show that the addition of nanoclay and PP‐g‐MAH decreased the melt strength and complex viscosity of B‐PP. When 3 wt % SC CO₂ was injected as the foaming agent for the extrusion foaming process, the introduction of nanoclay and PP‐g‐MAH significantly increased the expansion ratio of the obtained foamed samples as compared with that of the pure B‐PP matrix, lowered the die pressure, and increased the cell population density of the foamed samples to some extent. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44094.     

Dynamically cured polypropylene/Novolac blends compatibilized with maleic anhydride‐g‐polypropylene

In this article, the dynamic vulcanization process was applied to polypropylene (PP)/Novolac blends compatibilized with maleic anhydride‐grafted PP (MAH‐g‐PP). The influences of dynamic cure, content of MAH‐g‐PP, Novolac, and curing agent on mechanical properties of the PP/Novolac blends were investigated. The results showed that the dynamically cured PP/MAH‐g‐PP/Novolac blend had the best mechanical properties among all PP/Novolac blends. The dynamic cure of Novolac improved the modulus and stiffness of the PP/Novolac blends. The addition of MAH‐g‐PP into dynamically cured PP/Novolac blend further enhanced the mechanical properties. With increasing Novolac content, tensile strength, flexural modulus, and flexural strength increased significantly, while the elongation at break dramatically deceased. Those blends with hexamethylenetetramine (HMTA) as a curing agent had good mechanical properties at HMTA content of 10 wt %. Scanning electron microscopy (SEM) analysis showed that dynamically cured PP/MAH‐g‐PP/Novolac blends had finer domains than the PP/MAH‐g‐PP/Novolac blends. Thermogravimetric analysis (TGA) results indicated that the incorporation of Novolac into PP could improve the thermal stability of PP. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Effect of maleic‐anhydride‐grafted polypropylene as a compatibilizer on the properties of polypropylene/(modified carbon black) composites

Maleic‐anhydride‐grafted polypropylene (PP‐g‐MAH) was added, as a compatibilizer, to polypropylene (PP) composites filled with a hindered phenol and modified carbon black (CB). The interaction between the modified CB and PP‐g‐MAH, as proved by Fourier transform infrared spectroscopy, had a beneficial effect on the mechanical properties of the PP/(modified CB) composites and prevented the sharp decrease of the mechanical properties of these composites at higher filler concentration. The storage modulus of PP/(modified CB) was increased significantly by the incorporation of PP‐g‐MAH, especially when the temperature was lower than 0°C. When the content of PP‐g‐MAH was 5 wt% and the loading of the modified CB was 2 wt%, the best tensile strength was obtained. The system showed the best flexural strength and impact strength when the loading of the modified CB was 1 wt%. J. VINYL ADDIT. TECHNOL., 2011. © 2011 Society of Plastics Engineers     

Effect of coir fiber loading on mechanical and morphological properties of oil palm fibers reinforced polypropylene composites

Hybrid composites were fabricated by compounding process with varying the relative weight fraction of oil palm empty fruit bunch (EFB) and coir fibers to assess the effect of hybridization of oil palm EFB with coir fibers in polypropylene (PP) matrix. The mechanical and morphological properties of oil palm/coir hybrid composites were carried out. Tensile and flexural properties of oil EFB‐PP composites enhanced with hybridization of coir fibers except coir/oil palm EFB (25:75) hybrid composite, whereas highest impact properties at oil palm:coir fibers with 50:50 ratios. Results shown that hybrid composites with oil palm:coir fibers with 50:50 ratios display optimum mechanical properties. In this study, scanning electron microscopy (SEM) had been used to study morphology of tensile fractured surface of hybrid composites. Its clear from SEM micrograph that coir/EFB (50:50) hybrid composites display better tensile properties due to strong fiber/matrix bonding as compared with other formulations which lead to even and effective distribution of stress among fibers. The combination of oil palm EFB/coir fibers with PP matrix produced hybrid biocomposites material can be used to produce components such as rear mirrors' holder and window levers, fan blades, mallet, or gavel. POLYM. COMPOS., 35:1418–1425, 2014. © 2013 Society of Plastics Engineers     

Tensile properties,swelling, and water absorption behavior of rice‐husk‐powder‐filled polypropylene/(recycled acrylonitrile‐butadiene rubber) composites

The effect of rice husk powder (RHP) on the tensile properties, swelling, water absorption, and morphology of polypropylene (PP)/[recycled acrylonitrile‐butadiene rubber (NBRr)]/RHP composites was studied. Composites containing 0 to 30 parts of RHP per hundred parts of resin were prepared by using a Haake Rheomix Polydrive R 600/610 mixer at 180°C with a rotor speed of 50 rpm. Results indicated that the tensile strength and elongation at break decreased but that the tensile modulus increased with increasing amounts of RHP. Swelling of the PP/NBRr/RHP composites in oil and toluene increased with increasing RHP contents, and the composites exhibited a non‐Fickian diffusion with a two stage absorption mechanism. Micrographs acquired by SEM revealed an increasing number of voids and micro‐holes on the tensile‐fractured surfaces of the composites with increasing amounts of RHP. J. VINYL ADDIT. TECHNOL., 2011. © 2011 Society of Plastics Engineers     

Dynamically cured polypropylene/epoxy blends

The dynamic vulcanization process, usually used for the preparation of thermoplastic elastomers, was used to prepare polypropylene (PP)/epoxy blends. The blends had crosslinked epoxy resin particles finely dispersed in the PP matrix, and they were called dynamically cured PP/epoxy blends. Maleic anhydride grafted polypropylene (MAH‐g‐PP) was used as a compatibilizer. The effects of the reactive compatibilization and dynamic cure were studied with rheometry, capillary rheometry, and scanning electron microscopy (SEM). The crystallization behavior and mechanical properties of PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends were also investigated. The increase in the torque at equilibrium for the PP/MAH‐g‐PP/epoxy blends indicated the reaction between maleic anhydride groups of MAH‐g‐PP and the epoxy resin. The torque at equilibrium of the dynamically cured PP/epoxy blends increased with increasing epoxy resin content. Capillary rheological measurements also showed that the addition of MAH‐g‐PP or an increasing epoxy resin content increased the viscosity of PP/epoxy blends. SEM micrographs indicated that the PP/epoxy blends compatibilized with PP/MAH‐g‐PP had finer domains and more obscure boundaries than the PP/epoxy blends. A shift of the crystallization peak to a higher temperature for all the PP/epoxy blends indicated that uncured and cured epoxy resin particles in the blends could act as effective nucleating agents. The spherulites of pure PP were larger than those of PP in the PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends, as measured by polarized optical microscopy. The dynamically cured PP/epoxy blends had better mechanical properties than the PP/epoxy and PP/MAH‐g‐PP/epoxy blends. With increasing epoxy resin content, the flexural modulus of all the blends increased significantly, and the impact strength and tensile strength increased slightly, whereas the elongation at break decreased dramatically. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1437–1448, 2004     

The effect of coupling agents on the mechanical and physical properties of oil palm empty fruit bunch–polypropylene composites

Oil palm empty fruit bunch–polypropylene (EFB‐PP) composites have been produced using a twin‐screw extruder as the compounding equipment. Two levels of EFB were employed, 40 % and 60 % of the total weight of the sample. Three types of coupling agent, maleic anhydride‐modified polypropylene (commercial name Epolene E‐43), polymethylene(polyphenyl isocyanate) (PMPPIC) and 3‐(trimethoxysilyl)‐propylmethacrylate (TPM), were used. Overall, all coupling agents imparted considerable improvements in the flexural properties, E‐43 showing the highest enhancement. However, only E‐43 was observed to improve impact strength and tensile properties of the composites. All composites with coupling agents showed lower water absorption and thickness swelling. The absorption and swelling decreased as the loading of the coupling agents was increased. © 2000 Society of Chemical Industry     

三单体接枝共聚物对PP/云母填充体系性能的影响

将固相法接枝合成的聚丙烯与甲基丙烯酸甲酯／马来酸酐／丙烯酸丁酯的接枝共聚物PP-g-MMA/MAH/BA应用于PP／云母填充体系。研究接枝物对体系的力学性能、微观形态、热性能、加工性能及表面性能等的影响。结果表明，在PP／云母填充体系中加入适当的三单体接枝共聚物，可提高体系的拉伸强度、弯曲强度、维卡软化点及表面极性，并降低制品的成型收缩率；同时，体系的加工性能也得到改善。     

Improvement of the physico‐mechanical properties and stability of waste polypropylene in the presence of wood flour and (maleic anhydride)‐grafted polypropylene

This paper deals with (maleic anhydride)‐grafted polypropylene (MAH‐g‐PP) and wood flour reinforcement and their effects on the dynamic, mechanical, morphological, and rheological properties of waste polypropylene (PP) composites. MAH‐g‐PP was used as a compatibilizer to improve the physical interaction between the filler and matrix. The composites were prepared by using a twin‐screw extruder followed by injection molding. Thermal stability and mechanical properties of the compatibilized system increased as compared to their values for the uncompatibilized system. Also, nearly 60% and 30% loss was found for mechanical properties and weight loss, respectively, in a biodegradability study. J. VINYL ADDIT. TECHNOL., 20:24–30, 2014. © 2014 Society of Plastics Engineers     

Polypropylene–intumescent flame‐retardant composites based on meleated polypropylene as a coupling agent

The phosphoric acid‐pentaerythritol‐melamine copolymer, which is composed of three main components of intumescent flame retardant (IFR) and has optimal intumescent degree, was selected as IFR. The influence of meleated polypropylene (PP‐g‐MAH) on the properties and compatibility of IFR polypropylene (PP) composites were studied. The results obtained from mechanical tests, rheological behavior of composites, and scanning electron microscope showed that PP‐g‐MAH was a true coupling agent for IFR/PP blends and did not change the necessary flame retardancy. The cocrystallization between bulk PP and PP segments of PP‐g‐MAH was also proven by WAXD analysis. Flow test showed that the flow behaviors of composites in the melt are those of a pseudoplastic and it is very small for PP‐g‐MAH affecting rheological behavior of the PP/IFR composite. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 257–262, 2002     

Interface modification of compatibilized polyethylene terephthalate/polypropylene blends: Effect of compatibilization on thermomechanical properties and thermal stability

Polyethylene terephthalate (PET) and polypropylene (PP) are incompatible thermoplastics because of differences in chemical structure and polarity, hence their blends possess inferior mechanical and thermal properties. Compatibilization with a suitable block/graft copolymer is one way to improve the mechanical and thermal properties of the PET/PP blend. In this study, the toughness, dynamic mechanical analysis (DMA), and thermogravimetric analysis (TGA) of PET/PP blends were investigated as a function of different content of styrene‐ethylene‐butylene‐styrene‐g‐maleic anhydride (SEBS‐g‐MAH) compatibilizer. PET, PP, and SEBS‐g‐MAH were melt‐blended in a single step using the counter rotating twin screw extruder with compatibilizer concentrations of 0, 5, 10, and 15 phr, respectively. The impact strength of compatibilized blend with 10 phr SEBS‐g‐MAH increased by 300% compared to the uncompatibilized blend. Scanning electron microscope (SEM) micrographs show that the addition of 10 phr SEBS‐g‐MAH compatibilizer into the PET/PP blends decreased the particle size of the dispersed PP phase to the minimum level. The improvement of the storage modulus and the decrease in the glass transition temperature of the PET phase indicated an interaction among the blend components. Thermal stability of the PET/PP blends was significantly improved because of the addition of SEBS‐g‐MAH. J. VINYL ADDIT. TECHNOL., 23:45–54, 2017. © 2015 Society of Plastics Engineers     

Dynamic rheological behavior of reactively compatibilized polypropylene/polyamide 6 blending melts

The dynamic rheological behavior is measured by small amplitude oscillatory shear on rotational rheometer for polypropylene/polyamide 6 (PP/PA6) blends compatibilized by a polypropylene grafted maleic anhydride (PP‐g‐MAH). Scanning electron microscope (SEM) results show that the PP/PP‐g‐MAH/PA6 (=100/6/40wt) is sea‐island structure, the PP/PP‐g‐MAH/PA6 (=100/6/60wt) blend is semi‐cocontinuous. Coarse PA6 zones can be observed when the weight ratio is 100/6/80. At low frequency the complex viscosity, dynamic modulus of the PP/PP‐g‐MAH/PA6 (PP/PP‐g‐MAH = 100/6wt) blends first increase then drop with the increase of PA6 weight content in the range of 0–100, the maximum value arrives at the weight content of 60. The Cole–Cole plots as well as the weighted relaxation spectra of the blends have a main arc and a tail when the weight ratio of PP/PP‐g‐MAH/PA6 is in the range of 100/6/20–100/6/60, but have different shapes when the weight ratio increases to 100/6/80 and 100/6/100. The possible reason is the weight ratio of 100/6/80 and 100/6/100 is close to the phase inversion point. In fitting the storage modulus data at low frequency, Palierne's model with two parameters interfacial tension and interfacial shear modulus is better than Bousmina's model. Palierne's model with only one parameter of interfacial tension can not fit the data well. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42091.