Possibilities of perpendicular magnetic recording

The potential of perpendicular magnetic recording using a single-pole head and a double-layered medium has been investigated theoretically by computer analysis and compared with that of longitudinal magnetic recording. In conventional longitudinal recording, a recording demagnetizing loss due to the change of magnetization mode from semicircular to circular shapes occurs with increasing recording level at high bit density. In perpendicular magnetic recording, the perpendicular magnetization mode is maintained regardless of recording level even at an extremely high bit density of 571 kFRPI. This indicates that the perpendicular recording medium has a very high recording resolution, where a single bit size approaches several diameters of the microcrystalline particles of the Co-Cr layer. An ultrahigh density at which the recording area for 1 bit will reach 1 μ² at present and 500 Å₂ in future should be possible     

Extremely high bit density recording with single-pole perpendicular head

Since perpendicular magnetic recording is free from recording demagnetization, high-density recording up to the intrinsic limit of a recording medium is possible. This prediction was verified experimentally in a flexible disk system using a single-pole head and a Co-Cr/Ni-Fe double-layer medium. We could record and reproduce signals up to 680KFRPI. The recording bit length at the highest density was of the order of the Co-Cr columnar diameter.     

Perpendicular magnetic recording with a composite anisotropy film

For a recently proposed perpendicular recording system, a composite anisotropy medium has been developed to improve the recording sensitivity of the perpendicular recording head. The medium is composed of a Fe-Ni soft magnetic film and a Co-Cr perpendicular anisotropy film, which are successively deposited on a base by an r. f. sputtering. By using the new double layer medium, an extremely high recording sensitivity could be obtained, compared with the single layer Co-Cr medium. The recording current needed to saturate the double layer film decreased to one-tenth of that for the single layer Co-Cr film. Although the Fe-Ni layer was soft magnetic material, neither deterioration of the frequency response nor peak shift was observed for the double layer film. The reproduction with a perpendicular head was also investigated, and a high output voltage and a high signal-to-noise ratio were obtained.     

Perpendicular magnetic recording

This paper describes the recent studies for the magnetic head, the medium and the recording properties on a new perpendicular magnetic recording system. The complemental features between the perpendicular and the longitudinal recording are discussed to establish an efficient magnetic recording system. Superior response in the amplitude and the peak shift characteristics for a digital signal proves that the perpendicular magnetization mode is basically free from the recording demagnetization in high densities and the maximum density has been limited merely by the resolution of the reproducing head. Significant improvement for the recording and the reproducing sensitivities of a perpendicular head has been made by using a composite anisotropy medium composed by double layers of Fe-Ni and Co-Cr thin films.     

5.25 inch floppy disk drive using perpendicular magnetic recording

5.25 inch high density perpendicular magnetic recording floppy disk drive has beer developed by employing new types of high saturation magnetization ring head, Co-Cr single layer medium with Ge underlayer, head slider with ellipsoidal surface configuration to assure intimate head to medium contact, and signal equalization. By these combination, recording density D50 of 145 kFCI, peakshift of 28 % at 100 kFCI, signal to noise ratio of 40.4 dB for cut-off frequency 4.25 MHz, overwrite signal to noise ratio of 27 dB, measured by writing signals at 48 kFCI over previously written 100 kFCI signals were obtained as typical recording characteristics. These results would indicate that floppy disk drive with 100 kFCI recording density has enough system margin by above-mentioned combination. In this paper, design and performance of newly developed floppy disk drive are described.     

High-energy Co-Cr thin films sputtered on glass disks forperpendicular recording

The authors have developed high-energy Co-Cr thin-film perpendicular recording media for rigid disks. They obtained high perpendicular coercivity (Hc⊥) exceeding 2000 Oe with Co-Cr films sputtered on glass disks. They examined recording characteristics obtained with double-layered media and single-pole heads. Readout voltages were proportional to Hc⊥ up to 2000 Oe and not dependent on saturation magnetization. The authors explain the experimental results using the hysteresis curve of the Co-Cr film and the permeance factor determined by the magnetic reluctance of the head and medium. Using a magnetic circuit model, they clarify the effect of the difference in the operating point on the hysteresis curves of rigid- and flexible-disk systems     

Perpendicular magnetic recording performance of double-layer media

Perpendicular magnetic recording performance for double-layer (Co-Cr,Ni-Fe) media was analyzed, with a simple magnetization model, in comparison with single-layer media. The calculated output voltage from a ring-shaped reproducing head shows good agreement with experimental data. It is shown theoretically and empirically that the Co-Cr layer thickness can be reduced without sacrificing the output amplitude, if the Ni-Fe layer is placed underneath it to perform as a "flux sink" to extinguish the rear surface charge on the Co-Cr layer.     

Thin-film inductive heads for perpendicular recording

A modified thin-film magnetic head for perpendicular recording in rigid disk drives with improved read/write characteristics, especially at high areal bit densities, is presented. The head on which the modified design is based is described. It combines the advantages of single-pole heads and thin-film heads, writing with the sharp field edge of the leading pole and reading like a thin-film head. To increase the writing efficiency and improve the yield, the sequence of magnetic layers in the head is changed; the second layer of the four-layer head is embedded in the substrate, where it can be placed much closer to the pole tip of the first layer. The improved write capability depends mainly on the position of the embedded layer. In addition, there results an improved magnetic flux guidance from the embedded layer into the pole tip layer, providing the potential for a significant improvement in fabrication yield. The embedded-layer approach also allows a further increase in areal density. The results of read/write tests and the write-wide and read-narrow characteristics are presented     

Perpendicular stand-still recording in Co-Cr films

Some features of perpendicular recording were investigated by means of stand-still recording experiments. For this purpose several radio frequency (RF)-sputtered Co-Cr layers of two different compositions were used as media while a Permalloy single pole (SP) head was used as a write transducer. A magnetoresistive transducer (MRT) was utilized to read the recorded pattern. Further, an analytical model was developed enabling the magnetization induced by the head field in the recording medium to be calculated. Both calculations and experimental results show a sharpening of the transition, due to the demagnetizing field. For a good approximation it is sufficient to consider only the vertical head field component and vertical magnetization in the recording medium. This is a consequence of the well-developed perpendicular anisotropy and negligible in-plane remanence of the Co-Cr layers. In addition the read-out signal is completely determined by the magnetic surface charges. The remanent magnetization in the recording medium and therefore the read-out amplitude is limited by demagnetization and consequently determined by the coercivity of the Co-Cr layer. The medium noise of a dc-erased medium indicates magnetic structures of much larger dimensions than the size of the individual crystallites. This noise appears to be dependent on the saturation magnetization of the Co-Cr medium. Activation of the single pole head by a homogeneous field results in a nonlinear behavior, caused by head saturation effects. This is supported by simple one-dimensional calculations of the head field.     

Co-Cr perpendicular magnetic recording tape by vacuum deposition

The relation between the incident angle and the crystallographic orientation of a vacuum deposited Co-Cr film is discussed. Also presented are the magnetic properties and the orientation of both a Ni-Fe underlayer and the Co-Cr film for the double layer medium, and the experimental results about the composition distribution in the co-cr film. The films were deposited on a transporting polymer substrate by continuous vacuum deposition. It is found that the orientation of the Co-Cr film is determined only by the incident angle at the initial point of the film formation, and that deposition efficiency more than 50% can be achieved easily. A double layer medium with Ti film under the Ni-Fe film (Co-Cr/Ni-Fe/Ti medium), which is suitable for perpendicular magnetic recording, is produced by vacuum deposition. Auger depth profile in radial direction of the column of the Co-Cr film shows directly that there is Cr segregation near the columnar grain boundaries.     

A new W-shaped single-pole head and a high density flexible disk perpendicular magnetic recording system

A new single-pole head with no auxiliary pole was developed for perpendicular magnetic recording. The head is called WSP head (W-shaped Single Pole head) because the head has a W-shaped side core which contributes to increase the recording and reproducing sensitivitiy. The head field of the new head has the same distribusion as that of an auxiliary pole head[1]. The recording and reproducing sensitivity of the head is equal to or higher than that of a ring-type video head. The head eliminates mechanical problems which prevent its application in perpendicular magnetic recording because we can locate the head on one side of the recording medium. As a possible application of the WSP head, a 3 1/2-inch flexible disk recording system was constructed. A linear recording density of the flexible disk system was 65.5 kbits/inch. This density is equivalent to 8 times that of the existing high-density 3 1/2-inch micro-floppy and 11 times that of a 5 1/4-inch floppy disk. In termes of information storage, this density gives a 4 megabyte unformated capacity on one side of a 3 1/2-inch flexible disk. The overwrite signal-to-noise ratio was greater than 30 dB and the peakshift displacement was less than 10 % at the linear dinsity of 65.5 kbits/inch.     

Perpendicular magnetization structure of Co-Cr films

In a perpendicular recording system, a Co-Cr film as a medium is capable of storing very high density signals. Lorentz microscopy of 1000 kV TEM was used to observe the structure of recorded magnetizations in Co-Cr films having perpendicular anisotropy. A composite medium of a Co-Cr film with a soft magnetic back layer was shown by Lorentz microscopy to have a horseshoe magnetization structure. The stable antiparallel magnetization of transition in the Co-Cr layer determined the head-on magnetization structure of the soft magnetic back layer, which consists of a new straw-rope domain structure. The perpendicular magnetization structure of the Co-Cr film was found to consist of small domains magnetized through the film thickness which correspond to the columnar microstructure of the film. Since the intrinsic hysteresis loop of a Co-Cr film was shown to essentially have an ideal rectangular shape, it can be concluded that the Co-Cr layer of a composite film can be recorded by an ideal magnetizing process with negligible demagnetizing field at the transition.     

Perpendicular magnetic recording -- Evolution and future

This paper reviews research results for the head, medium and recording properties of a perpendicular recording system. Superior bit density characteristics obtained so far indicate that perpendicular recording is basically free from demagnetization in the high density region and that it will establish a new field of recording technology in the future. The prediction is explained in the context of complementary profiles of longitudinal and perpendicular recording. At the very beginning of magnetic recording, a perpendicular-type head was considered but abandoned because a suitable medium did not exist. Progress in material science has enabled us to develop a perpendicular recording medium which is very well suited for ultra high density recording. As so often happens, history has repeated itself through another study of perpendicular recording.     

Measurements and self-consistent calculations of the magnetic fields near a perpendicular medium

Several models used to describe magnetic fields from perpendicular media and heads have been evaluated with the high-resolution field measurement system. Perpendicular fringing fields near statically written magnetization patterns were computed using an iterative self-consistent technique utilizing a hyperbolic-tangent and a Stoner-Wohlfarth hysteresis model. The fields predicted by both theories were compared with those measured from magnetization patterns statically written in two different Co-Cr media with a ring head and a single-pole head where the media had either been presaturated or demagnetized. The field distributions predicted by both theories were in generally good agreement with the measurements; the theoretical amplitudes were within 20 percent for the hyperbolic-tangent model, but significantly larger amplitude errors were found for the Stoner-Wohlfarth model. Write fields were measured from a ring head and a single-pole head, and a theory for each of the heads was shown to be in excellent agreement with the measurements.     

Media for high density magnetic recording

Longitudinal recording is limited at high bit densities by recording demagnetization, self-demagnetization, and adjacent-bit demagnetization, which occur during the writing-demagnetization processes. To minimize these adverse effects it becomes necessary to resort to extreme scaling of the media parameters and their thickness, with the consequence of greatly increasing the difficulty of fabrication and the cost of such optimized media. Pure perpendicular recording circumvents these writing and demagnetization problems because of the strong head coupling of a single pole head with a double layer medium, positive interaction between adjacent bits, and low self-demagnetization at high bit densities. Therefore, it does not require any extreme scaling of the media magnetic parameters and their thickness. Of great interest, at least for the next several years, are the quasi-perpendicular particulate media which can support perpendicular magnetization. These include the isotropic, high-squareness media, and oriented perpendicular media employing particles with uniaxial crystalline or shape anisotropies. The attractiveness of these media derives from their excellent recording performance and from the fact that they preserve the existing head/media interface and they utilize existing coating facilities which should reflect favorably on their cost. In this paper the advantages and disadvantages of the various media under development for high density magnetic recording are compared, and predictions are made for their potential application in future systems.     

Magnetic recording configuration for densities beyond 1 Tb/in/sup 2/ and data rates beyond 1 Gb/s

A new magnetic recording system is evaluated that includes the single-pole head, a new medium design, and the soft underlayer of perpendicular recording. The proposed medium consists of perpendicular grains with anisotropy directions tilted optimally about 45/spl deg/ with respect to the perpendicular direction. Here, focus is on the tilt angle at 45/spl deg/ in the crosstrack direction, including a small but typical dispersion. The write pole consists of a tapered-neck single-pole head with a very small throat height that yields maximized write fields without increased edge track degradation. The advantages of tilted perpendicular recording are discussed using theoretical and numerical micromagnetic analyses. This design achieves a much higher signal-to-noise ratio (SNR) than conventional recording, because it is less sensitive to medium orientation distributions and, for the same thermal decay, can utilize media with much smaller grain sizes. The switching speed is much more rapid due to increased recording torque. Estimated recording limits for tilted perpendicular recording with a medium-jitter SNR of 17 dB are beyond densities of 1 Tb/in/sup 2/ and data rates of 1 Gb/s.     

Review of head-media coupling in magnetic recording

Recent advance of magnetic recording technology has resulted in tremendous increase in area densities. Several new components were developed: Thin film media, and thin film head in longitudinal recording; Single-layer media, double-layer media, and probe head in perpendicular recording. A variety of head and media combinations become possible, and each has a different degree of head-media coupling. The soft magnetic underlayer in double-layer perpendicular media has such a strong coupling with the head that the head and media must be treated as a single entity in the analysis. The evaluation of only a head or a medium without knowing its counterpart could be quite misleading. Optimization of head-media coupling to select the most suitable combination becomes a key factor in designing a high density recording system. We will review the recording and reproducing processes from both the theoretical and experimental aspects for all the head-media structures which have some practical interest.     

Fabrication of SmCo5 Double-Layered Perpendicular Magnetic Recording Media

We fabricated SmCo₅ double-layered perpendicular magnetic recording media with high perpendicular magnetic anisotropy for realizing ultra high density recording. A double-layered medium with a Ru buffer layer introduced between a Cu/Ti intermediate layer and a Co-Zr-Nb soft magnetic underlayer exhibited high perpendicular magnetic anisotropy, whereas that without the Ru buffer layer did not. Auger electron spectroscopy revealed that the Ru buffer layer inhibited interdiffusion between the Cu/Ti intermediate layer and the Co-Zr-Nb soft magnetic underlayer. We report here for the first time the read-write characteristics of SmCo₅ double-layered perpendicular magnetic recording media. The medium noise was small in the medium with a Sm-Co layer deposited under high Ar gas pressure owing to small magnetic clusters     

Simulation of the perpendicular recording process including image charge effects

This paper presents a complete model for the perpendicular recording process in single-pole-head keeper-layer configurations. It includes the influence of the image-charge distributions in the head and the keeper layer. Based on calculations of magnetization distributions in standstill situations, the model describes the relaxation process that takes place if the activated head is shifted along the recording layer, periodically switching its head field. The magnetization distributions thus derived are used in combination with a model for the readback process to calculate the readback flux and voltage pulses. For the sake of arithmetical convenience, the model was applied to a recording configuration with a thick single-pole head, but it can also be used for calculations with other head shapes, e.g. thin single-pole heads.     

Spectral response nulls for single-pole heads in perpendicularrecording

This letter discusses the dependence of the nulls in the spectral response function of a single-pole head, used in perpendicular magnetic recording with a double-layer medium, upon the pole thickness and the distance between the pole and the underlayer. Exact results from a two-dimensional model are used to produce approximate but accurate relationships, and are compared with previously published theoretical and experimental results where full data are available