Effect of synthesis temperature on the properties of LiFePO4/C composites prepared by carbothermal reduction

LiFePO₄/C composite cathode materials were synthesized by carbothermal reduction method using inexpensive FePO₄ as raw materials and glucose as conductive additive and reducing agent. The precursor of LiFePO₄/C was characterized by differential thermal analysis and thermogravimetry. The microstructure and morphology of the samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM) and particle size analysis. Cyclic voltammetry (CV) and charge/discharge cycling performance were used to characterize their electrochemical properties. The results showed that the LiFePO₄/C composite synthesized at 650 °C for 9 h exhibited the most homogeneous particle size distribution. Residual carbon during processing was coated on LiFePO₄, resulting in the enhancement of the material's electronic properties. Electrochemical measurements showed that the discharge capacity first increased and then decreased with the increase of synthesis temperature. The optimal sample synthesized at 650 °C for 9 h exhibited a highest initial discharge capacity of 151.2 mA h g⁻¹ at 0.2 C rate and 144.1 mA h g⁻¹ at 1 C rate with satisfactory capacity retention rate.     

Morphological characterization of LiFePO4/C composite cathode materials synthesized via a carboxylic acid route

A new type of LiFePO₄/C composite surrounded by a web containing both amorphous and crystalline carbon phases was synthesized by incorporating malonic acid as a carbon source using a high temperature solid-state method. SEM, TEM/SAED/EDS and HRTEM were used to analyze surface morphology and confirmed for the first time that crystalline carbon was present in LiFePO₄/C composites. The composite was effective in enhancing the electrochemical properties such as capacity and rate capability, because its active component consists of nanometer-sized particles containing pores with a wide range of sizes. An EDS elemental map showed that carbon was uniformly distributed on the surface of the composite crystalline particles. TEM/EDS results clearly show a dark region that is LiFePO₄ with a trace of carbon and a gray region that is carbon only. To evaluate the materials’ electrochemical properties, galvanostatic cycling and conductivity measurements were performed. The best cell performance was delivered by the material coated with 60 wt.% malonic acid, which delivered first cycle discharge capacity of 149 mAh g⁻¹ at a C/5 rate and sustained 222 cycles at 80% of capacity retention. When carboxylic acid was used as a carbon source to produce LiFePO₄, overall conductivity increased from 10⁻⁵ to 10⁻⁴ S cm⁻¹, since particle growth was prevented during the final sintering process.     

Novel synthesis of LiFePO4-Li3V2(PO4)3 composite cathode material by aqueous precipitation and lithiation

LiFePO₄-Li₃V₂(PO₄)₃ composite cathode material is synthesized by aqueous precipitation of FeVO₄·xH₂O from Fe(NO₃)₃ and NH₄VO₃, following chemical reduction and lithiation with oxalic acid as the reducer and carbon source. Samples are characterized by XRD, SEM and TEM. XRD pattern of the compound synthesized at 700 °C indicates olivine-type LiFePO₄ and monoclinic Li₃V₂(PO₄)₃ are co-existed. TEM image exhibits that LiFePO₄-Li₃V₂(PO₄)₃ particles are encapsulated with a carbon shell 5-10 nm in thickness. The LiFePO₄-Li₃V₂(PO₄)₃ compound cathode shows good electrochemical performance, and its discharge capacity is about 139.1 at 0.1 C, 135.5 at 1 C and 116 mA h g⁻¹ at 3 C after 30 cycles.     

Optimized solid-state synthesis of LiFePO4 cathode materials using ball-milling

Olivine-type LiFePO₄ cathode materials were synthesized by a solid-state reaction method and ball-milling. The ball-milling time, heating time and heating temperature are optimized. A heating temperature higher than 700 °C resulted in the appearance of impurity phase Fe₂P and growth of large particle, which was shown by high resolution X-ray diffraction and field emission scanning electron microscopy. The impurity phase Fe₂P exhibited a considerable capacity loss at the 1st cycle and a gradual increase in discharge capacity upon cycling. Moreover, it exhibited an excellent high-rate capacity of 104 mAh g⁻¹ at 3 C in spite of the large particle size. The optimum synthesis conditions for LiFePO₄ were ball-milling for 24 h and heat-treatment at 600 °C for 3 h. LiFePO₄/Li cells showed an enhanced cycling performance and a high discharge capacity of 160 mAh g⁻¹ at 0.1 C.     

A simple,cheap soft synthesis routine for LiFePO4 using iron(III) raw material

An order olivine structure LiFePO₄ was synthesized with a simple rheological phase reaction (RPR) of LiOH·H₂O and FePO₄·4H₂O in the presence of PEG as a reductive agent and carbon source. A required amount of water was added to the starting materials to form the rheological precursor and decomposed at 700 °C to form the crystalline phase LiFePO₄ directly, without ball-milling, preparation of intermediates, pre-sintering and post-deposition treatment. Fine particles with an average particle size about 216 nm are examined by scanning electron microscopy (SEM) and optical particle size analyzer. An initial discharge capacity of 157 mAh g⁻¹ was achieved for the as-prepared LiFePO₄ material with a rate of 0.1C (17 mA g⁻¹), what's more, this material shows excellent specific capacity, charge–discharge efficiency and cycle efficiency at high current rates, almost no capacity loss can be observed up to 40 cycles with the rate of 1, 2 and 3C at room temperature. The simple, cheap process as well as the excellent high-rate performance makes this RPR method feasible commercially.     

Effect of mechanical activation process parameters on the properties of LiFePO4 cathode material

Pure, nano-sized LiFePO₄ and carbon-coated LiFePO₄ (LiFePO₄/C) positive electrode (cathode) materials are synthesized by a mechanical activation process that consists of high-energy ball milling and firing steps. The influence of the processing parameters such as firing temperature, firing time and ball-milling time on the structure, particle size, morphology and electrochemical performance of the active material is investigated. An increase in firing temperature causes a pronounced growth in particle size, especially above 600 °C. A firing time longer than 10 h at 600 °C results in particle agglomeration; whereas, a ball milling time longer than 15 h does not further reduce the particle size. The electrochemical properties also vary considerably depending on these parameters and the highest initial discharge capacity is obtained with a LiFePO₄/C sample prepared by ball milling for 15 h and firing for 10 h at 600 °C. Comparison of the cyclic voltammograms of LiFePO₄ and LiFePO₄/C shows enhanced reaction kinetics and reversibility for the carbon-coated sample. Good cycle performance is exhibited by LiFePO₄/C in lithium batteries cycled at room temperature. At the high current density of 2C, an initial discharge capacity of 125 mAh g⁻¹ (73.5% of theoretical capacity) is obtained with a low capacity fading of 0.18% per cycle over 55 cycles.     

Electrochemical properties of LiFePO4 prepared via hydrothermal route

LiFePO₄ as a cathode material for rechargeable lithium batteries was prepared by hydrothermal process at 170 °C under inert atmosphere. The starting materials were LiOH, FeSO₄, and (NH₄)₂HPO₄. The particle size of the obtained LiFePO₄ was 0.5 μm. The electrochemical properties of LiFePO₄ were characterized in a mixed solvent of ethylene carbonate and diethyl carbonate (1:1 in volume) containing 1.0 mol dm⁻³ LiClO₄. The hydrothermally synthesized LiFePO₄ exhibited a discharge capacity of 130 mA h g⁻¹, which was smaller than theoretical capacity (170 mA h g⁻¹). The annealing of LiFePO₄ at 400 °C in argon atmosphere was effective in increasing the discharge capacity. The discharge capacity of the annealed LiFePO₄ was 150 mA h g⁻¹.     

Electrochemical properties of LiFe0.9Mn0.1PO4/Fe2P cathode material by mechanical alloying

LiFePO₄, olivine-type LiFe_0.9Mn_0.1PO₄/Fe₂P composite was synthesized by mechanical alloying of carbon (acetylene back), M₂O₃ (M = Fe, Mn) and LiOH·H₂O for 2 h followed by a short-time firing at 900 °C for only 30 min. By varying the carbon excess different amounts of Fe₂P second phase was achieved. The short firing time prevented grain growth, improving the high-rate charge/discharge capacity. The electrochemical performance was tested at various C/x-rate. The discharge capacity at 1C rate was increased up to 120 mAh g⁻¹ for the LiFe_0.9Mn_0.1PO₄/Fe₂P composite, while that of the unsubstituted LiFePO₄/Fe₂P and LiFePO₄ showed only 110 and 60 mAh g⁻¹, respectively. Electronic conductivity and ionic diffusion constant were measured. The LiFe_0.9Mn_0.1PO₄/Fe₂P composite showed higher conductivity and the highest diffusion coefficient (3.90 × 10⁻¹⁴ cm² s⁻¹). Thus the improvement of the electrochemical performance can be attributed to (1) higher electronic conductivity by the formation of conductive Fe₂P together with (2) an increase of Li⁺ ion mobility obtained by the substitution of Mn²⁺ for Fe²⁺.     

Formation mechanism of LiFePO4/C composite powders investigated by X-ray absorption spectroscopy

The local structure and oxidation states for both the precursors and the LiFePO₄/C composite powders were investigated by X-ray absorption spectroscopy (XAS) to provide a deep insight into their formation mechanism. It was found that the local structure and oxidation states of the precursors and the synthesized LiFePO₄/C powders as well as the electrochemical properties of the synthesized powders were strongly influenced by the R ratio (R: molar ratio of citric acid to total metal ions). The oxidation states of iron ions of the precursors for R = 1 and 0.75 consist mainly of Fe(II) and traces of Fe(III). However, the oxidation state of iron ions of the precursor for R = 0.5 comprises mainly of Fe(III). The oxidation state of iron ions of all the synthesized powders is Fe(II). The structure of the precursors and the synthesized powders for R = 1 and 0.75 is more ordering than that for R = 0.5. It is in good agreement with the observation of the cation mixing obtained from the Riteveld analysis of the XRD data. The better the electrochemical performance is, the more ordering the structure or the less the cation mixing. However, the effect of the R values on the carbon content is also essential for the electrochemical properties of the synthesized LiFePO₄/C composite powders. Increasing the carbon content leads to the increase in the electronic conductivity but impedes the Li⁺ ion diffusion of the composite materials. Consequently, the powders synthesized at the optimal R ratio of 0.75 exhibited the highest initial capacity, about 150 mAh g⁻¹ when cycled at 1/40 C rate at room temperature. The structural scheme of the precursors and the synthesized powders and the formation mechanism of the LiFePO₄/C composite powders are also addressed in this work.     

Cathode performance of olivine-type LiFePO4 synthesized by chemical lithiation

Chemical lithiation with LiI in acetonitrile was performed for amorphous FePO₄ synthesized from an equimolar aqueous suspension of iron powder and an aqueous solution of P₂O₅. An orthorhombic LiFePO₄ olivine structure was obtained by annealing a chemically lithiated sample at 550 °C for 5 h in Ar atmosphere. The average particle size remained at approximately 250 nm even after annealing. The lithium content in the sample was quantitatively confirmed by Li atomic absorption analysis and ⁵⁷Fe Mössbauer spectroscopy. While an amorphous FePO₄/carbon composite cathode has a monotonously decreasing charge–discharge profile with a reversible capacity of more than 140 mAh g⁻¹, the crystallized LiFePO₄/carbon composite shows a 3.4 V plateau corresponding to a two-phase reaction. This means that the lithium in the chemically lithiated sample is electrochemically active. Both amorphous FePO₄ and the chemically lithiated and annealed crystalline LiFePO₄ cathode materials showed good cyclability (more than 140 mAh g⁻¹ at the 40th cycle) and good discharge rate capability (more than 100 mAh g⁻¹ at 5.0 mA cm⁻²). In addition, the fast-charge performance was found to be comparable to that with LiCoO₂.     

Effects of carbon coating and iron phosphides on the electrochemical properties of LiFePO4/C

Carbon coated LiFePO₄ (LiFePO₄/C) with different contents of high electron conductive iron phosphide phase was synthesized by an aqueous sol–gel method in a reductive sintering atmosphere. Different synthesis parameters were used for adjusting the microstructure and phase compositions of the products. The effects of the carbon coating and iron phosphides on the electrochemical properties of the LiFePO₄/C electrodes were studied by means of testing the discharge capacities at rates of 0.1–5C (1C = 170 mAh g⁻¹) and analyzing the CV curves. The results show that carbon coating in a content of 1.5 wt.% derived from the carbon source of ethylene glycol greatly decreases the particle size of LiFePO₄ in one order in the specific surface area, and significantly improves the rate capability of LiFePO₄. The effect of the content of FeP on the capacity of the carbon coated LiFePO₄ was different at different discharge rates. Increasing the content of FeP from 1.2 to 3.7 wt.% slightly decreases the capacity of LiFePO₄/C at low discharge rate (0.1C and 1C), but obviously increases the capacity of LiFePO₄/C when the discharge rate is increased to 5C. For the carbon free sample, even it also has 1.8 wt.% FeP, it still possesses poor capacity due to the large particle size of LiFePO₄ and the lack of conductivity. And too much iron phosphides lowers the discharge capacity of the electrode since they are inert for the deinsertion/insertion of lithium ion.     

A study on the electrochemical characteristics of LiFePO4 cathode for lithium polymer batteries by hydrothermal method

Phospho-olivine LiFePO₄ cathode materials were prepared by hydrothermal reaction at 150 °C. Carbon black was added to enhance the electrical conductivity of LiFePO₄. LiFePO₄-C powders (0, 3, 5 and 10 wt.%) were characterized by X-ray diffraction (XRD) and transmission electron microscope (TEM). LiFePO₄-C/solid polymer electrolyte (SPE)/Li cells were characterized electrochemically by charge/discharge experiments at a constant current density of 0.1 mA cm⁻² in a range between 2.5 and 4.3 V vs. Li/Li⁺, cyclic voltammetry (CV) and ac impedance spectroscopy. The results showed that initial discharge capacity of LiFePO₄ was 104 mAh g⁻¹. The discharge capacity of LiFePO₄-C/SPE/Li cell with 5 wt.% carbon black was 128 mAh g⁻¹ at the first cycle and 127 mAh g⁻¹ after 30 cycles, respectively. It was demonstrated that cycling performance of LiFePO₄-C/SPE/Li cells was better than that of LiFePO₄/SPE/Li cells.     

Synthesis and electrochemical characterization of carbon-coated nanocrystalline LiFePO4 prepared by polyacrylates-pyrolysis route

A carbon-coated nanocrystalline LiFePO₄ cathode material was synthesized by pyrolysis of polyacrylate precursor containing Li⁺, Fe³⁺ and PO₄⁻. The powder X-ray diffraction (XRD) and high-resolution TEM micrographs revealed that the LiFePO₄/C composite as prepared has a core-shell structure with pure olivine LiFePO₄ crystallites as cores and intimate carbon coating as a shell layer. Between the composite particulates, there exists a carbon matrix binding the nanocrystallites together into micrometer particles. The electrochemical measurements demonstrated that the LiFePO₄/C composite with an appropriate carbon content can deliver a very high discharge capacity of 157 mAh g⁻¹ (>92% of the theoretical capacity of LiFePO₄) with 95% of its initial capacity after 30 cycles. Since this preparation method uses less costly materials and operates in mild synthetic conditions, it may provide a feasible way for industrial production of the LiFePO₄/C cathode materials for the lithium-ion batteries.     

Structural and electrochemical properties of Cl-doped LiFePO4/C

Cl-doped LiFePO₄/C cathode materials were synthesized through a carbothermal reduction route, and the microstructure and electrochemical performances were systematically studied. Cl-doped LiFePO₄/C cathode materials presented a high discharge capacity of ∼90 mAh g⁻¹ at the rate of 20 C (3400 mA g⁻¹) at room temperature. Electrochemical impedance spectroscopy and cyclic voltamperometry indicated the optimized electrochemical reaction and Li⁺ diffusion in the bulk of LiFePO₄ due to Cl-doping. The improved Li⁺ diffusion capability is attributed to the microstructure modification of LiFePO₄ via Cl-doping.     

Morphology and electrical properties of carbon coated LiFePO4 cathode materials

Core-shell LiFePO₄@C composites were synthesized successfully from FePO₄/C precursor using the polyvinyl alcohol (PVA) as the reducing agent, followed by a chemical vapor deposition (CVD) assisted solid-state reaction in the presence of Li₂CO₃. Some physical and chemical properties of the products were characterized by X-ray powder diffraction (XRD), Raman, SEM, TEM techniques. The effect of morphology and electrochemical properties of the composites were thoroughly investigated. XRD patterns showed that LiFePO₄ has an order olivine structure with space group of Pnma. TEM micrographs exhibited that the LiFePO₄ particles encapsulated with 3-nm thick carbon shells. The powders were homogeneous with grain size of about 0.8 μm. Compared with those synthesized by traditional organic carbon source mixed method, LiFePO₄@C composite synthesized by CVD method exhibited better discharge capacity at initial 155.4 and 135.8 mAh g⁻¹ at 0.1C and 1C rate, respectively. It is revealed that the carbon layer coated on the surface of LiFePO₄ and the amorphous carbon wrapping and connecting the particles enhanced the electronic conductivity and rate performances of the cathode materials.     

LiFePO4 with enhanced performance synthesized by a novel synthetic route

Pure LiFePO₄ was synthesized by heating an amorphous LiFePO₄. The amorphous LiFePO₄ obtained through lithiation of FePO₄·xH₂O by using oxalic acid as a novel reducing agent at room temperature. FePO₄·xH₂O was prepared through co-precipitation by employing FeSO₄·7H₂O and H₃PO₄ as raw materials. X-ray diffraction (XRD), scanning electron microscopy (SEM) observations showed that LiFePO₄ composites with fine particle sizes between 100 nm and 200 nm, and with homogenous sizes distribution. The electrochemical performance of LiFePO₄ powder synthesized at 500 °C were evaluated using coin cells by galvanostatic charge/discharge. The synthesized LiFePO₄ composites showed a high electrochemical capacity of 166 mAh g⁻¹ at the 0.1C rate, and possessed a favorable capacity cycling maintenance at the 0.1C, 0.2C, 0.5C and 1C rate.     

Improved high-rate charge/discharge performances of LiFePO4/C via V-doping

V-doped LiFePO₄/C cathode materials were prepared through a carbothermal reduction route. The microstructure was characterized by X-ray diffraction, X-ray photoelectron spectroscopy and scanning electron microscopy. The electrochemical Li⁺ intercalation performances of V-doped LiFePO₄/C were compared with those of undoped one through galvanostatic intermittent titration technique, cyclic voltamperometry, and electrochemical impedance spectrum. V-doped LiFePO₄/C showed a high discharge capacity of ∼70 mAh g⁻¹ at the rate of 20 C (3400 mA g⁻¹) at room temperature. The significantly improved high-rate charge/discharge capacity is attributed to the increase of Li⁺ ion “effective” diffusion capability.     

Lithium oxalyldifluoroborate/carbonate electrolytes for LiFePO4/artificial graphite lithium-ion cells

The electrolytes based on lithium oxalyldifluoroborate (LiODFB) and carbonates have been systematically investigated for LiFePO₄/artificial graphite (AG) cells, by ionic conductivity test and various electrochemical tests, such as cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and charge-discharge test. The conductivity of nine electrolytes as a function of solvent composition and LiODFB salt concentration has been studied. The coulombic efficiency of LiFePO₄/Li and AG/Li half cells with these electrolytes have also been compared. The results show that 1 M LiODFB EC/PC/DMC (1:1:3, v/v) electrolyte has a relatively higher conductivity (8.25 mS cm⁻¹) at 25 °C, with high coulombic efficiency, good kinetics characteristics and low interface resistance. With 1 M LiODFB EC/PC/DMC (1:1:3, v/v) electrolyte, LiFePO₄/AG cells exhibit excellent capacity retention ∼92% and ∼88% after 100 cycles at 25 °C and at elevated temperatures up to 65 °C, respectively; The LiFePO₄/AG cells also have good rate capability, the discharge capacity is 324.8 mAh at 4 C, which is about 89% of the discharge capacity at 0.5 C. However, at −10 °C, the capacity is relatively lower. Compared with 1 M LiPF₆ EC/PC/DMC (1:1:3, v/v), LiFePO₄/AG cells with 1 M LiODFB EC/PC/DMC (1:1:3, v/v) exhibited better capacity utilization at both room temperature and 65 °C. The capacity retention of the cells with LiODFB-based electrolyte was much higher than that of LiPF₆-based electrolyte at 65 °C, while the capacity retention and the rate capacity of the cells is closed to that of LiPF₆-based electrolyte at 25 °C. In summary, 1 M LiODFB EC/PC/DMC (1:1:3, v/v) is a promising electrolyte for LiFePO₄/AG cells.     

Synthesis of carbon-coated LiFePO4 nanoparticles with high rate performance in lithium secondary batteries

A novel preparation technique was developed for synthesizing carbon-coated LiFePO₄ nanoparticles through a combination of spray pyrolysis (SP) with wet ball milling (WBM) followed by heat treatment. Using this technique, the preparation of carbon-coated LiFePO₄ nanoparticles was investigated for a wide range of process parameters such as ball-milling time and ball-to-powder ratio. The effect of process parameters on the physical and electrochemical properties of the LiFePO₄/C composite was then discussed through the results of X-ray diffraction (XRD) analysis, field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), the Brunauer-Emmet-Teller (BET) method and the use of an electrochemical cell of Li|1 M LiClO₄ in EC:DEC = 1:1|LiFePO₄. The carbon-coated LiFePO₄ nanoparticles were prepared at 500 °C by SP and then milled at a rotating speed of 800 rpm, a ball-to-powder ratio of 40/0.5 and a ball-milling time of 3 h in an Ar atmosphere followed by heat treatment at 600 °C for 4 h in a N₂ + 3% H₂ atmosphere. SEM observation revealed that the particle size of LiFePO₄ was significantly affected by the process parameters. Furthermore, TEM observation revealed that the LiFePO₄ nanoparticles with a geometric mean diameter of 146 nm were coated with a thin carbon layer of several nanometers by the present method. Electrochemical measurement demonstrated that cells containing carbon-coated LiFePO₄ nanoparticles could deliver markedly improved battery performance in terms of discharge capacity, cycling stability and rate capability. The cells exhibited first discharge capacities of 165 mAh g⁻¹ at 0.1 C, 130 mAh g⁻¹ at 5 C, 105 mAh g⁻¹ at 20 C and 75 mAh g⁻¹ at 60 C with no capacity fading after 100 cycles.     

Synthesis and electrochemical properties of olivine LiFePO4 prepared by a carbothermal reduction method

LiFePO₄/C composite cathode material was prepared by carbothermal reduction method, which uses NH₄H₂PO₄, Li₂CO₃ and cheap Fe₂O₃ as starting materials, acetylene black and glucose as carbon sources. The precursor of LiFePO₄/C was characterized by differential thermal analysis and thermogravimetry. X-ray diffraction (XRD), scanning electron microscopy (SEM) micrographs showed that the LiFePO₄/C is olivine-type phase, and the addition of the carbon reduced the LiFePO₄ grain size. The carbon is dispersed between the grains, ensuring a good electronic contact. The products sintered at 700 °C for 8 h with glucose as carbon source possessed excellent electrochemical performance. The synthesized LiFePO₄ composites showed a high electrochemical capacity of 159.3 mAh g⁻¹ at 0.1 C rate, and the capacity fading is only 2.2% after 30 cycles.