Oxidation of triclosan by ferrate: reaction kinetics, products identification and toxicity evaluation

The Crystal Violet (CV) dye represented one of the major triphenylmethane dyes used in textile-processing and some other industrial processes. Various metals doped titanium dioxide (TiO(2)) photocatalysts have been studied intensively for the photodegradation of dye in wastewater treatment. In order to understand the mechanistic detail of the metal dosage on the activities enhancement of the TiO(2) based photocatalyst, this study investigated the CV photodegradation reactions under UV light irradiation using a Pt modified TiO(2) photocatalyst. The results showed that Pt-TiO(2) with 5.8% (W/W) Pt dosage yielded optimum photocatalytic activity. Also the effect of pH value on the CV degradation was well assessed for their product distributions. The degradation products and intermediates were separated and characterized by HPLC-ESI-MS and GC-MS techniques. The results indicated that both the N-de-methylation reaction and the oxidative cleavage reaction of conjugated chromophore structure occurred, but with significantly different intermediates distribution implying that Pt doped TiO(2) facilitate different degradation pathways compared to the P25-TiO(2) system.     

纳米TiO2的制备,表征及光催化性能的研究

采用硬脂酸凝胶（SAG）法制备了TiO2纳米材料,用差热分析,热重分析,X射线衍射对合成过程进行了研究。用X射线光电子能谱（XPS）对其表面状态进行了分行。TiO2纳米材料对甲基橙溶液光催化降解结果表明：催化剂浓度、初始溶液pH值和金属离子对降解效率有较大影响。     

Heterogeneous photocatalytic degradation of monochlorobenzene in water

This investigation evaluated the photocatalytic degradation of monochlorobenzene (MCB) in an aqueous TiO(2) suspension. In accordance with the experimental results, the degradation of MCB was a function of the initial substrate concentration, incident light intensity, and TiO(2) dosage. However, the solution pH had insignificant effect on the degradation efficiency. The heterogeneous photocatalytic degradation of MCB followed the Langmuir-Hinshelwood kinetics. The adsorption coefficient of MCB (K) and the observed degradation rate constant (k) were calculated as 13.4 mM(-1) and 0.0054 mM min(-1), respectively. In addition, a 0.255 dependency of the initial degradation rate on the light intensity revealed the considerable adverse effect of e(-)-h(+) pair recombination. Both mineralization and dechlorination occurred during the photocatalytic degradation of MCB. Under the operating condition of initial MCB concentration of 0.1mM, light intensity of 5.68 microEinsteins(-1), TiO(2) dosage of 1.0 g L(-1), and solution pH of 7, about 93.7% of MCB was mineralized after 240 min of irradiation. Nevertheless, 64.3% of the stoichiometric amount of Cl(-) ions was released into the bulk solution. The simulation results derived from the X-ray photoelectron spectroscopy (XPS) analysis was suggested that the interaction between Cl(-) ions and TiO(2) surface tended to lower the released amount of Cl(-) ions.     

Synergy between surface adsorption and photocatalysis during degradation of humic acid on TiO2/activated carbon composites

A photocatalyst comprising nano-sized TiO(2) particles on granular activated carbon (GAC) was prepared by a sol-dipping-gel process. The TiO(2)/GAC composite was characterized by scanning electron microscopy (SEM), X-ray diffractiometry (XRD) and nitrogen sorptometry, and its photocatalytic activity was studied through the degradation of humic acid (HA) in a quartz glass reactor. The factors influencing photocatalysis were investigated and the GAC was found to be an ideal substrate for nano-sized TiO(2) immobilization. A 99.5% removal efficiency for HA from solution was achieved at an initial concentration of 15 mg/L in a period of 3h. It was found that degradation of HA on the TiO(2)/GAC composite was facilitated by the synergistic relationship between surface adsorption characteristics and photocatalytic potential. The fitting of experimental results with the Langmuir-Hinshelwood (L-H) model showed that the reaction rate constant and the adsorption constant values were 0.1124 mg/(L min) and 0.3402 L/mg. The latter is 1.7 times of the calculated value by fitting the adsorption equilibrium data into the Langmuir equation.     

Preparation of re-usable photocatalytic filter for degradation of Malachite Green dye under UV and vis-irradiation

Sn(4+) doped and undoped nano-TiO(2) particles easily dispersed in water were synthesized without using organic solvent by hydrothermal process. Nanostructure-TiO(2) based thin films were prepared on flyswatter substrate, made with stainless steel, by dip-coating technique. The structure, surface and optical properties of the particles and thin films were characterized by element analysis and XRD, BET, SEM and UV/vis/NIR techniques. The photocatalytic performance of the films were tested for degradation of Malachite Green dye in solution under UV and vis-lights. The results showed that the coated flyswatter has a very high photocatalytic performance for the photodegradation of Malachite Green irradiated with UV and vis-lights. The results also proved that the hydrothermally synthesized nano-TiO(2) particles are fully anatase crystalline form and are easily dispersed in water, the coated surfaces are hydrophilic, and the doping of transition metal ion efficiently improved the degradation performance of TiO(2)-coated flyswatter. The photocatalytic performances determined at both irradiation conditions were very good and were almost similar to each other for Sn(4+) doped TiO(2)-coated flyswatter and it can be repeatedly used with increasing photocatalytic activity compared to undoped TiO(2)-coated flyswatter.     

Photocatalytic reduction of Cr(VI) over different TiO2 photocatalysts and the effects of dissolved organic species

The toxic Cr(VI) in industrial wastewaters can be removed by a reduction from Cr(VI) to Cr(III) and a followed precipitation treatment. The reduction of Cr(VI) to Cr(III) is able to be achieved by a photocatalytic process. Thus, photocatalytic reduction of Cr(VI) over TiO2 catalysts was investigated in both the absence and presence of organic compounds. The TiO(2) catalyst was pre-calcined at different temperatures to tune the photocatalytic activity and surface area of the photocatalyst. Under the tested conditions, the photocatalytic reduction of Cr(VI) behaved as a pseudo-first-order reaction in kinetics. In the absence of any organic species, the rate constant (kCr) for the photocatalytic reduction of Cr(VI) was found to be increased initially, passing a maximum, and then decreased, as calcination temperature was increased. In the presence of organic compounds, however, kCr was decreased with the increase of calcination temperature. A marked synergistic effect between the photocatalytic reduction of Cr(VI) and organic compounds was observed over the photocatalyst with the largest specific surface area. These results demonstrated that the photocatalytic reduction of Cr(VI) alone was dependent on both of specific surface area and crystalline structure of the photocatalyst in the absence of any organic compounds, but was dominated by the specific surface area of the photocatalyst in the presence of organic compounds because of the synergistic effect between the photocatalytic reduction of Cr(IV) and the photocatalytic oxidation of organic compounds.     

Photocatalytic degradation of aqueous propoxur solution using TiO2 and Hbeta zeolite-supported TiO2

Photocatalytic activity of TiO2 and zeolites supported TiO2 were investigated using propoxur as a model pollutant. Hbeta, HY and H-ZSM-5 zeolites were examined as supports for TiO2. Hbeta was chosen as the TiO2 support based on the adsorption capacity of propoxur on these zeolites (Hbeta>HY=H-ZSM-5). TiO2/Hbeta photocatalysts with different wt.% were prepared and characterized by XRD, FT-IR and BET surface area. The progress of photocatalytic degradation of aqueous propoxur solution using TiO2 (Degussa P-25) and TiO2 supported on Hbeta zeolite was monitored using TOC analyzer, HPLC and UV-vis spectrophotometer. The degradation of propoxur was systematically studied by varying the experimental parameters in order to achieve maximum degradation efficiency. The initial rate of degradation with TiO2/Hbeta was higher than with bare TiO2. TOC results revealed that TiO2 requires 600min for complete mineralization of propoxur whereas TiO2/Hbeta requires only 480min. TiO2/Hbeta showed enhanced photodegradation due to its high adsorption capacity on which the pollutant molecules are pooled closely and hence degraded effectively.     

Photocatalytic degradation of Congo Red by hydrothermally synthesized nanocrystalline TiO2 and identification of degradation products by LC-MS

Degradation of Congo Red (CR) dye in aqueous solutions was investigated by means of photocatalysis of TiO2 which was hydrothermally synthesized at 200 degrees C in 2 h, in anatase phase with 8 nm crystallite size. Efficiency of TiO2 in photocatalytic degradation under visible irradiation was studied by investigating the effects of amount of TiO2, irradiation time, initial CR concentration and pH. It was found that complete decolorization is achieved within 30 min of irradiation. Effects of nitrate and sulphate ions and humic acid on the degradation were also tested. The results were compared with Degussa P-25 TiO2 at the same degradation conditions. Degradation products were detected using LC-MS technique. The probable pathways for the formation of degradation products were proposed.     

复合电沉积制备SnO2/TiO2薄膜及其光电催化性能

为了寻求廉价、高效和稳定的光催化剂,用复合电沉积技术在紫铜片上制备了Sn/TiO2薄膜,经300℃热氧化使之形成SnO2/TiO2复合电极.利用SEM,XRD对薄膜进行了表征,以甲基橙为模型化合物,对复合电极的光催化和光电催化性能进行了测定.研究表明:该薄膜由0.3~1μm的颗粒构成,每个颗粒又由纳米晶粒形成;电极具有多孔结构,膜中的SnO2以两种不同的晶体结构存在;在薄膜质量相等的情况下,SnO2/TiO2薄膜的光催化活性是纯TiO2粒子膜的2.87倍;外加一定偏压下,其催化性能大幅度提高.     

Photocatalytic degradation of indigo carmine in aqueous solution by TiO2-coated non-woven fibres

The photocatalytic degradation of indigo carmine has been investigated in aqueous solutions using TiO2 coated non-woven fibres as photocatalyst. The experiments were carried out to investigate the factors influencing the photocatalytic degradation, such as the previous adsorption in the dark, initial concentration of dye solution, temperature, and pH. The experimental results show that adsorption is an important parameter controlling the apparent kinetic constant of the degradation. The photocatalytic degradation rate was favoured by a high concentration of solution in respect to Langmuir-Hinshelwood model. The degradation rate was pH and temperature dependent with a high degradation rate at high temperature.     

泡沫镍负载TiO2和TiO2/Al2O3薄膜的光催化性能研究

以泡沫镍为载体，Al2O3作为过渡中间层，用溶胶-凝胶法在泡沫镍上负载锐钛矿相的TiO2薄膜，制成泡沫金属基的TiO2和TiO2／Al2O3光催化剂，利用XRD和FE-SEM等测试手段对其性质进行表征，用乙醛气体的光催化降解测试其活性．研究表明：泡沫镍负载的TiO2和TiO2／Al2O3薄膜具有良好的光催化活性，特别是TiO2／Al2O3薄膜具有更高的催化活性．这是由于负载的Al2O3过渡中间层增大了载体的比表面积，具有吸附浓缩作用，同时也增加了负载光催化剂的活性位数量．实验表明：TiO2／Al2O3薄膜的光催化活性和稳定性较单一的TiO2薄膜有非常显著的提高．     

碳纤维负载钐掺杂纳米TiO_2复合材料的制备与表征

采用静电纺丝法和热处理工艺制备了纳米碳纤维负载掺杂1.5%(摩尔分数)Sm的纳米Ti O2复合材料(Sm-Ti O2/CNFs),利用SEM、EDX、TEM、FTIR和XRD对其组成和结构进行了表征,并以甲基橙为降解对象,考察了Sm-Ti O2/CNFs复合材料在紫外光照射下对甲基橙的光催化降解效果。结果表明,掺杂Sm3+的Ti O2以锐钛矿晶型均匀分散在碳纳米纤维的表面和内部,质量分数为20%左右;相对于未掺杂的Ti O2/CNFs样品,Sm-Ti O2/CNFs的光催化活性提高约37%。     

Effect of pH on solar photocatalytic reduction and deposition of Cu(II), Ni(II), Pb(II) and Zn(II): speciation modeling and reaction kinetics

The present study is targeted on the effect of pH on solar photocatalytic removal of metal ions from wastewater. Photoreductive deposition and dark adsorption of metal ions Cu(II), Ni(II), Pb(II) and Zn(II), using solar energy irradiated TiO(2), has been investigated at pH values 2, 4, 7, 8 and 10. Modeling of metal species at the studied pH values has been performed and speciation is used as a tool for discussing the photodeposition. The decreasing order of metal deposition at pH 2 and 4 was found to be Pb(II)>Cu(II)>Ni(II) congruent with Zn(II). In the neutral and alkaline pH conditions (pH 7, 8 and 10) the order was Cu(II)>Zn(II)>Ni(II)>Pb(II).     

Nitrogen-doped TiO2 nanotube array films with enhanced photocatalytic activity under various light sources

Highly ordered nitrogen-doped titanium dioxide (N-doped TiO(2)) nanotube array films with enhanced photocatalytic activity were fabricated by electrochemical anodization, followed by a wet immersion and annealing post-treatment. The morphology, structure and composition of the N-doped TiO(2) nanotube array films were investigated by FESEM, XPS, UV-vis and XRD. The effect of annealing temperature on the morphology, structures, photoelectrochemical property and photo-absorption of the N-doped TiO(2) nanotube array films was investigated. Liquid chromatography and mass spectrometry were applied to the analysis of the intermediates coming from the photocatalytic degradation of MO. The experimental results showed that there were four primary intermediates existing in the photocatalytic reaction. Compared with the pure TiO(2) nanotube array film, the N-doped TiO(2) nanotubes exhibited higher photocatalytic activity in degradating methyl orange into non-toxic inorganic products under both UV and simulated sunlight irradiation.     

Photodegradation of acetaminophen in TiO(2) suspended solution

This study investigated the photocatalytic degradation of acetaminophen (APAP) in TiO(2) suspended solution under a 250 W metal halide lamp. The influence of some parameters on the degradation of acetaminophen was studied and described in details, such as initial APAP concentration, initial pH value and TiO(2) dosage. After 100 min irradiation, about 95% of APAP is decomposed in the 1.0 g L(-1) TiO(2) aqueous solution with an initial concentration of 100 micromol L(-1). The effect of adsorption at three different pH values has also been analyzed and it has been conducted that pH 3.5, at which APAP was readily adsorbed also degraded at a faster rate. Reaction rate at pH 6.9 and pH 9.5 was 2.84 and 2.96 microM min(-1), respectively. Direct hole (h(+)) oxidation and ipso-substitution was found to be the main initial step for APAP degradation. Main reaction intermediates and products were identified by GC/MS analysis. The mechanism of acetaminophen photocatalytic degradation in TiO(2) suspended solution was studied not only experimentally but also theoretically by calculating the frontier electron density of APAP. The results obtained indicated that TiO(2) photocatalytic degradation is a highly effective way to remove APAP from wastewater and drinking water without any generation of more toxic products.     

Solar photocatalytic removal of Cu(II), Ni(II), Zn(II) and Pb(II): speciation modeling of metal-citric acid complexes

The present study is targeted on solar photocatalytic removal of metal ions from wastewater. Photoreductive deposition and dark adsorption of metal ions Cu(II), Ni(II), Pb(II) and Zn(II), using solar energy irradiated TiO2, has been investigated. Citric acid has been used as a hole scavenger. Modeling of metal species has been performed and speciation is used as a tool for discussing the photodeposition trends. Ninety-seven percent reductive deposition was obtained for copper. The deposition values of other metals were significantly low [nickel (36.4%), zinc (22.2%) and lead (41.4%)], indicating that the photocatalytic treatment process, using solar energy, was more suitable for wastewater containing Cu(II) ions. In absence of citric acid, the decreasing order deposition was Cu(II)>Ni(II)>Pb(II)>Zn(II), which proves the theoretical thermodynamic predictions about the metals.     

Photocatalytic degradation of azo dyes using Au:TiO2, gamma-Fe2O3:TiO2 functional nanosystems

We report photocatalytic degradation studies on Navy Blue HE2R (NB) dye on significant details as a representative from the class of azo dyes using functional nanosystems specifically designed to allow a strong photocatalytic activity. A modified sol-gel route was employed to synthesize Au and gamma-Fe2O3 modified TiO2 nanoparticles (NPs) at low temperature. The attachment strategy is better because it allows clear surface of TiO2 to remain open for photo-catalysis. X-ray diffraction, Raman and UV-VIS spectroscopy studies showed the presence of gold and iron oxide phases along-with the anatase TiO2 phase. TEM studies showed TiO2 nanocomposite particles of size approximately 10-12 nm. A detailed investigation on heterogeneous photocatalytic performance for Navy Blue HE2R dye was done using the as-synthesized catalysts Au:TiO2 and gamma-Fe2O3:TiO2 in aqueous suspension under 8 W low-pressure mercury vapour lamp irradiation. Also, the photocatalytic degradation of Amranth and Orange G azo dyes were studied. The surface modified TiO2 NPs showed significantly improved photocatalytic activity as compared to pure TiO2. Exposure of the dye to the UV light in the presence of pure and gold NPs attached TiO2 catalysts caused dye degradation of about approximately 20% and approximately 80%, respectively, in the first couple of hours. In the presence of gamma-Fe2O3 NPs attached TiO2, a remarkable approximately 95% degradation of the azo dye was observed only in the first 15 min of UV exposure. The process parameters for the optimum catalytic activity are established which lead to a complete decoloration and substantial dye degradation, supported by the values of the Chemical Oxygen Demand (COD) approximately 93% and Total Organic Carbon (TOC) approximately 65% of the treated dye solution after 5 hours on the employment of the UV/Au:TiO2/H2O2 photocatalytic process.     

Photocatalytic decolorization and degradation of dye solutions and wastewaters in the presence of titanium dioxide

In this study, the photocatalytic degradation of two commercial azo dyes in the presence of TiO(2) suspensions as photocatalyst has been investigated. The degradation of the dyes follows a pseudo-first-order kinetics according to the Langmuir-Hinshelwood model. Under the certain experimental conditions, in the presence of TiO(2) P-25 decolorization is achieved within 100 min of illumination, while in the presence of TiO(2) Hombikat UV-100 complete color disappearance is accomplished in less than 50 min of light exposure. The influence of various parameters, such as the type and mass of the catalyst, the initial concentration of the dye, etc. on the degradation process was examined. The mineralization of organic carbon was also evaluated by measuring the dissolved organic carbon (DOC) of the dye solutions. Moreover, the toxic properties of the dye solutions treated by photocatalysis were examined by the use of a Microtox bioassay (Vibrio fischeri). Finally, experiments using real textile wastewater were also carried out, in order to examine the effectiveness of the method to a more complex substrate.     

Photocatalytic degradation of three azo dyes using immobilized TiO2 nanoparticles on glass plates activated by UV light irradiation: Influence of dye molecular structure

In order to discuss the effect of chemical structure on photocatalysis efficiency, the photocatalytic degradation of three commercial textile dyes (C.I. Acid Orange 10 (AO10), C.I. Acid Orange 12 (AO12) and C.I. Acid Orange 8 (AO8)) with different structure and different substitute groups has been investigated using supported TiO₂ photocatalyst under UV light irradiation. All the experiments were performed in a circulation photochemical reactor equipped with a 15-W UV lamp emitted around 365 nm. The investigated photocatalyst was industrial Millennium PC-500 (crystallites mean size 5–10 nm) immobilized on glass plates by a heat attachment method. SEM images of the immobilized TiO₂ nanoparticles showed the good coating on the plates, after repeating the deposition procedure three times. Our results indicated that the photocatalytic decolorization kinetics of the dyes were in the order of AO10 > AO12 > AO8. Photocatalytic mineralization of the dyes was monitored by total organic carbon (TOC) decrease, changes in UV–vis spectra and ammonium ion formation. The dye solutions could be completely decolorized and effectively mineralized, with an average overall TOC removal larger than 94% for a photocatalytic reaction time of 6 h. The nitrogen-to-nitrogen double bond of the azo dyes was transformed predominantly into NH₄⁺ ion. The kinetic of photocatalytic decolorization of the dyes was found to follow a first-order rate law. The photocatalysis efficiency was evaluated by figure-of-merit electrical energy per order (E_EO).     

Porous SnIn4S8 microspheres in a new polymorph that promotes dyes degradation under visible light irradiation

Porous SnIn(4)S(8) microspheres were initially synthesized through a facile solvothermal approach and were investigated as visible-light driven photocatalysts for dyes degradation in polluted water. The photocatalysts were characterized by XRD, SEM, TEM, N(2) adsorption-desorption, and UV-vis diffuse reflectance techniques. Results demonstrated that the as-synthesized SnIn(4)S(8) was of a new tetragonal polymorph, showing a band-gap of 2.5 eV, a specific surface area of 197 m(2) g(-1), and an accessible porous structure as well. The photocatalytic activity of the porous SnIn(4)S(8) was evaluated by decomposition of several typical organic dyes including methyl orange, rhodamine B, and methylene blue in aqueous solution under visible light irradiation. It is demonstrated that porous SnIn(4)S(8) was highly photoactive and stable for dyes degradation, showing photocatalytic activity much higher than binary constituent sulfides like In(2)S(3), SnS(2), or even ternary chalcogenide ZnIn(2)S(4) photocatalyst. The excellent photocatalytic performance of porous SnIn(4)S(8) is the consequence of its high surface area, well-defined porous texture, and large amount of hydroxyl radicals.