Comprehensive analysis of thermodynamic models for CO2 absorption into a blended N,N-diethylethanolamine-1,6-hexamethyl diamine (DEEA-HMDA) amine

In this work, CO₂ equilibrium solubility of 1M N,N-diethylethanolamine (DEEA):2M 1,6-hexamethyl diamine (HMDA), 1.5M DEEA:1.5M HMDA and 2M DEEA:1M HMDA was studied with a temperature range of 298–333 K and CO₂ partial pressure range of 8–100 kPa. Seven thermodynamic models including Empirical model, Kent and Eisenberg (KE) model, Hu–Chakma model, Austgen model, Helei Liu model, Liu et al. model, and Li–Shen model were developed by correlating reaction equilibrium constants with observed equilibrium solubility of CO₂ in mixed amine solvents. The evaluation of those models was conducted in terms of the average absolute relative deviation (AARD). The results indicated that Liu et al. model considering T, [Amine], P_total and [CO₂(aq)] can better represent this complex system with an AARD of 8.06%. Meanwhile, comprehensive comparison and analysis were also performed to identify the contribution of parameters to develop models, which could provide a guideline for the development of accurate thermodynamic models for representation of thermodynamic behaviors.     

The development of kinetics model for CO2 absorption into tertiary amines containing carbonic anhydrase

CO₂ absorption into aqueous solutions of two tertiary alkanolamines, namely, MDEA and DMEA with and without carbonic anhydrase (CA) was investigated with the use of the stopped‐flow technique at temperatures in the range of 293–313 K, CA concentration varying from 0 to 100 g/m³ in aqueous MDEA solution with the amine concentration ranging from 0.1 to 0.5 kmol/m³, and CA concentration varying from 0 to 40 g/m³ in aqueous DMEA solution with the amine concentration ranging from 0.05 to 0.25 kmol/m³. The results show that the pseudofirst‐order reaction rate (k_{0, amine}; s^?1) is significantly enhanced in the presence of CA as compared with that without CA. The enhanced values of the kinetic constant in the presence of CA has been calculated and a new kinetics model for reaction of CO₂ absorption into aqueous tertiary alkanolamine solutions catalyzed by CA has been established and used to make comparisons of experimental and calculated pseudo first‐order reaction rate constant (k_{0, with CA}) in CO₂‐MDEA‐H₂O and CO₂‐DMEA‐H₂O solutions. The AADs were 15.21 and 15.17%, respectively. The effect of pKa on the CA activities has also been studied by comparison of CA activities in different tertiary amine solutions, namely, TEA, MDEA, DMEA, and DEEA. The pKa trend for amines were: DEEA > DMEA > MDEA > TEA. In contrast, the catalyst enhancement in amines was in the order: TEA> MDEA> DMEA> DEEA. Therefore, it can be seen that the catalyst enhancement in the amines decreased with their increasing pKa values. © 2017 American Institute of Chemical Engineers AIChE J, 2017     

New AMP/polyamine blends for improved CO2 capture: Study of kinetic and equilibrium features

2-Amino-2-methyl-1-propanol (AMP), which is the sterically hindered form of monoethanolamine (MEA), is a credible substitute to conventional CO₂-capturing solvents. Its performance can be improved by blending with a highly reactive polyamine promoter. Two such aqueous blends of AMP/TETA and AMP/TEPA were chosen here (TETA = triethylenetetramine and TEPA = tetraethylenepentamine). The kinetics of CO₂ absorption in the proposed blends was investigated at 308, 313, and 318 K using the stirred cell technique. The concentrations of AMP and polyamine were varied between 2 to 3 kmol/m³ and 0.1 to 0.5 kmol/m³, respectively. From the measured values of the fast pseudo-first order constants, the second-order rate constants for the reactions of CO₂ with TETA (14 695 m³/(kmol s)) and TEPA (19 250 m³/(kmol s)) were determined at T = 313 K. Both TETA and TEPA react faster with CO₂ than MEA. Further, the respective activation energy values were found (40 and 37 kJ/mol). Finally, the equilibrium solubility of CO₂ for both blends was measured at T = 303 K. The loading capacity was higher than that for the aqueous blends of AMP/MEA, AMP/DEA, and AMP/MDEA (here, DEA and MDEA denote diethanolamine and N-methyldiethanolamine). The highest value of loading capacity (1.12 mol CO₂/mol amine at 2.01 kPa equilibrium partial pressure of CO₂) was noted in AMP/TEPA mixtures. The new findings on our proposed blends will strengthen the AMP/polyamine application in CO₂ separation.     

A Study on CO2 Absorption Kinetics by Aqueous Solutions of N,N‐Diethylethanolamine and N‐Ethylethanolamine

N‐Ethylethanolamine (EEA) and N,N‐diethylethanolamine (DEEA) represent promising candidate alkanolamines for CO₂ removal from gaseous streams, as they can be prepared from renewable resources. In this work, the reaction rate constant for the reaction between CO₂ and EEA was determined from the absorption rate measurements of CO₂ in a blend comprising DEEA, EEA and H₂O. A stirred‐cell reactor with a plane, horizontal gas‐liquid interface was used for the absorption studies. While the DEEA concentration in the formulated solution was varied in the range of 1.5–2.5 kmol/m³, the initial EEA concentration was 0.1 kmol/m³. A zwitterion mechanism for EEA and a base‐catalyzed hydration mechanism for DEEA were used to describe the reaction kinetics. At 303 K, the second‐order reaction rate constant for the CO₂ reaction with EEA was found to be 8041 m³/(kmol s). The liquid‐side mass transfer coefficient was also estimated, and its value (0.004 cm/s) is in line with those typical of stirred‐cell reactors.     

A comparative kinetics study of CO2 absorption into aqueous DEEA/MEA and DMEA/MEA blended solutions

The kinetics of CO₂ absorption into aqueous solutions of N,N‐diethylethanolamine (DEEA), and N,N‐dimethylethanolamine (DMEA), and their blends with monoethanolamine (MEA) have been studied in a stopped‐flow apparatus. The kinetics experiments were carried out at the concentrations of DEEA and DMEA varying from 0.075 to 0.175 kmol/m³, respectively, and that of MEA ranging between 0.0075 and 0.0175 kmol/m³, over the temperature range of 293–313 K. Two kinetics models are proposed to interpret the reaction in the blended amine systems and the results show that the model which incorporates the base‐catalyzed hydration mechanism and termolecular mechanism resulted in a better prediction. Furthermore, the kinetics behaviors of CO₂ absorption into two blended systems are comprehensively discussed according to their molecular structures. It can be concluded that the interaction between tertiary amines and primary amines as well as the alkyl chain length of tertiary amines have a significant influence on the kinetics. © 2017 American Institute of Chemical Engineers AIChE J, 64: 1350–1358, 2018     

Kinetics study of carbon dioxide absorption in aqueous solutions of 1,6-hexamethyldiamine (HMDA) and 1,6-hexamethyldiamine, N,N′ di-methyl (HMDA, N,N′)

A study towards the kinetics of CO₂ in aqueous solutions of 1,6-hexamethyl diamine (HMDA) and 1,6-hexamethyl diamine, N,N′ di-methyl (HMDA, N,N′) was performed at concentrations ranging from 0.5 to 2.5 mol/L and temperatures from 283 up to 303 K. The kinetics data were determined by CO₂ absorption experiments using a stirred cell reactor with a flat interface between gas and liquid. These new CO₂ solvents were identified in earlier work for their high CO₂ capacity and limited corrosiveness. The experimental technique was validated using kinetic experiments for a 2.5 mol/L monoethanolamine solution. In view of double amine functionality and the six carbon chain between the amine groups, attention was paid to whether the amine groups acted independently and whether or not internal cyclisation would affect the carbamate forming mechanism. The reaction order with respect to HMDA was found to vary from 1.4 to 1.8 with increasing temperature. Absorption experiments in an equimolar solution of HMDA with HCl showed that the two amine groups react independently from each other towards CO₂. The reactivity of both diamines was more than five times larger than for monoethanolamine. The secondary diamine HMDA, N,N′ was found to be even more reactive towards CO₂. Additionally, the effect of CO₂ loading on the kinetics was studied for 0.5 mol/L aqueous solutions of HMDA and HMDA, N,N′ at 293 K. Both solvents are from absorption kinetics point of view good candidates for further evaluation as solvent (-component) for CO₂ capture.     

The solubility of H2S and CO2 in a diethanolamine solution at low partial pressures

The solubility of H₂S, CO₂ and their mixtures in a 2.0 kmol m^?3 aqueous solution of diethanolamine has been determined at 40°C and 100°C at partial pressures of the acid gases between 0.003 and 6.5 kPa. The results have been compared with values calculated by a method of prediction.     

Vapour–liquid equilibrium of CO2 in aqueous solutions of N‐methyl‐2‐ethanolamine

The equilibrium solubility of CO₂ into aqueous solution of sterically hindered N‐methyl‐2‐ethanolamine or methyl amino ethanol (MAE) was investigated in the temperature range of 303.1–323.1 K and total CO₂ pressure in the range of 1–350 kPa. The N‐methyl‐2‐ethanolamine aqueous solutions studied were 0.968, 1.574, 2.240 and 3.125 mol kg^?1 of solvent. © 2011 Canadian Society for Chemical Engineering     

Mass transfer performance and correlations for CO2 absorption into aqueous blended of DEEA/MEA in a random packed column

The mass transfer performance of CO₂ absorption into blended N,N‐diethylethanolamine (DEEA)/ethanolamine (MEA) solutions was investigated using a lab‐scale absorber (H = 1.28 m, D = 28 mm) packed with Dixon ring random packing. The mass transfer coefficient K_Ga_v, the unit volume absorption rate Φ, outlet concentration of CO₂ (y_CO2), and the bottom temperature T_bot of CO₂ in aqueous DEEA/MEA solutions were determined over the feed temperature range of 298.15–323.15 K, lean CO₂ loading of 0.15–0.31 mol/mol, over a wide range of liquid flow rate of 3.90–9.75 m³/m²‐h, by using inert gas flow rate of 26.11–39.17 kmol/m²‐h and 6–18 kPa CO₂ partial pressure. The results show that liquid feed temperature, lean CO₂ loading, liquid flow rate, and CO₂ partial pressure had significant effect on those parameters. However, the inert gas flow rate had little effect. To allow the mass transfer data to be really utilized, K_Ga_v and y_out correlations for the prediction of mass transfer performance were proposed and discussed. © 2017 American Institute of Chemical Engineers AIChE J, 63: 3048–3057, 2017     

Simultaneous absorption of CO<Subscript>2</Subscript> and SO<Subscript>2</Subscript> into aqueous AMP/NH<Subscript>3</Subscript> solutions in binary composite absorption system

To enhance the absorption rate for CO₂ and SO₂, aqueous ammonia (NH₃) solution was added to an aqueous 2-amino-2-methyl-1-propanol (AMP) solution. The simultaneous absorption rates of AMP and a blend of AMP+ NH₃ for CO₂ and SO₂ were measured by using a stirred-cell reactor at 303 K. The process operating parameters of interest in this study were the solvent and concentration, and the partial pressures of CO₂ and SO₂. As a result, the addition of NH₃ solution into aqueous AMP solution increased the reaction rate constants of CO₂ and SO₂ by 144 and 109%, respectively, compared to that of AMP solution alone. The simultaneous absorption rate of CO₂/SO₂ on the addition of 1 wt% NH₃ into 10 wt% AMP at a p _A1 of 15 kPa and p _A2 of 1 kPa was 5.50×10⁻⁶ kmol m⁻² s⁻¹, with an increase of 15.5% compared to 10 wt% AMP alone. Consequently, the addition of NH₃ solution into an aqueous AMP solution would be expected to be an excellent absorbent for the simultaneous removal of CO₂/SO₂ from the composition of flue gas emitted from thermoelectric power plants.     

Investigation of CO2 solubility in monoethanolamine hydrochloride based deep eutectic solvents and physical properties measurements

Deep eutectic solvents (DESs) have drawn a growing research interest for applications in a wide range of scientific and industrial arenas. However, a limited effort has been reported in the area of gas separation processes and particularly the carbon dioxide capture. This study introduces a novel set of DESs that were prepared by complexing ethylenediamine (EDA), monoethanolamine (MEA), tetraethylenepentamine (TEPA), triethylenetetramine (TETA) and diethylenetriamine (DETA) as hydrogen bond donors to monoethanolamide hydrochloride (EAHC) salt as a hydrogen bond acceptor. The absorption capacity of CO₂ was evaluated by exploiting a method based on measuring the pressure drop during the absorption process. The solubility of different DESs was studied at a temperature of 313.15 K and initial pressure of 0.8 MPa. The DES systems 1EAHC:9DETA, 1EAHC:9TETA and 1EAHC:9TEPA achieved the highest CO₂ solubility of 0.6611, 0.6572 and 0.7017 mol CO₂·(mole DES)⁻¹ respectively. The results showed that CO₂ solubility in the DESs increased with increasing the molar ratio of hydrogen bond donor. In addition, the CO₂ solubility increased as the number of amine groups in the solvent increases, therefore, increasing the alkyl chain length in the DESs, resulted in increasing the CO₂ solubility. FTIR analysis confirms the DES synthesis since no new functional group was identified. The FTIR spectra also revealed the carbamate formation in DES-CO₂ mixtures. In addition, the densities and viscosities of the synthesized DESs were also measured. The CO₂ initial investigation of reported DESs shows that these can be potential alternative for conventional solvents in CO₂ capture processes.     

Kinetics and new mechanism study of CO2 absorption into water and tertiary amine solutions by stopped-Flow technique

The objective of the present work was to find the accurate kinetic models and mechanism for CO₂ absorption into tertiary amine solution, aiming at understanding the contribution of the CO₂ reaction with H₂O, OH⁻, and tertiary amines on the overall reaction rate. First, the kinetics of CO₂ absorption into water instead of a buffer solution were studied using the stopped-flow technique at 293–313 K, with initial CO₂ molar concentration of 1.1–37.3 mM. The experimental first-order reaction rate constant () was determined to be about 1000 times larger than the value for CO₂ absorption into buffer solution reported in the reference. The was then correlated by a proposed semiempirical model and a simplified theoretical model, giving the activation energy for CO₂ reacting with H₂O as fitted by the simplified theoretical model in good agreement with the value of previous research. Also, the pH values and hydroxyl ion concentrations of aqueous Diethylaminoethanol (DEEA) solutions were determined at 293–313 K, with DEEA molar concentration of 0.1–0.4 M and CO₂ loading of 0–0.626 mol/mol. In addition, the observed first-order reaction rate constant ( k_{0_DEEA} ) of binary DEEA-H₂O solution with DEEA molar concentration of 0.1–0.4 M reacting with CO₂ was determined at 293–313 K. It should be pointed out that the kinetic experiments of CO₂ absorption into DEEA solution was done with the molar ratio of DEEA to CO₂ fixed at 20. The values of k_{0_DEEA} were then fitted and predicted by four models (i.e., termolecular model, base-catalyzed model, the improved model, and Khalifah model). The results show the improved model and Khalifah model can predict k_{0_DEEA} well with an average absolute relative difference (AARD) <5%. The predicted results indicate that the contribution of OH⁻ to k_{0_DEEA} cannot be ignored for the absorption of CO₂ into tertiary amine solutions, and could be responsible for 50–70% of the total absorption reaction rate. Furthermore, the k₀ value of CO₂ absorption into aqueous triethanolamine and CO₂-loaded DEEA solution were further investigated and comprehensively discussed, suggesting that both pK _a and the CO₂ solubility affect k₀ , with pK _a having a much more significant effect. © 2018 American Institute of Chemical Engineers AIChE J, 65: 652–661, 2019     

Solubility and diffusivity of CO<Subscript>2</Subscript> in <Emphasis Type="Italic">n</Emphasis>-butanol + N235 system and absorption mechanism of CO<Subscript>2</Subscript> in a coupled reaction-extraction process

The absorption of CO₂ in insoluble organic amine is crucial for understanding the mechanism of coupled reaction-extraction-crystallization process between aqueous chloride and CO₂. In this study, the solubility and diffusivity of CO₂ in n-butanol + N235 system were measured and reported. The absorption of CO₂ in the system is a physical absorption behavior and the solubility of CO₂ decreases with the increase of the mass fraction of N235. The diffusivity of CO₂ increases firstly and then decreases with the increase in the mass fraction of N235. Moreover, the absorption mechanism of CO₂ in the coupled reaction-extraction-crystallization process was investigated and identified by experiments. The results indicated that in the coupled reaction-extraction-crystallization process, CO₂ is absorbed by the aqueous phase rather than by the organic phase and further transferred into the aqueous phase.

Open image in new window

     

The solubility of mixtures of carbon dioxide and hydrogen sulphide in an aqueous dipa solution

The solubility of mixtures of carbon dioxide and hydrogen sulphide in an aqueous solution of di-isopropanolamine (2.5 kmol m^?3 DIPA) has been measured at temperatures of 40 °C and 100°C. Partial pressures of CO₂ ranged from 2.0 to 5991 kPa, while partial pressures of H₂S ranged from 1.3 to 4126 kPa.     

A new model for correlation and prediction of equilibrium CO2 solubility in N‐methyl‐4‐piperidinol solvent

In this work, the equilibrium CO₂ solubility in the aqueous tertiary amine, N‐methyl‐4‐piperidinol (MPDL) was measured over a range of temperatures, CO₂ partial pressures and amine concentrations. The dissociation constant of the MPDL solution was determined as well. A new thermodynamic model was developed to predict the equilibrium CO₂ solubility in the MPDL‐H₂O‐CO₂ system. This model, equipped with the correction factor (C_f), can give reasonable prediction with an average absolute deviation of 2.0%, and performs better than other models (i.e., KE model, Li‐Shen model, and Hu‐Chakma). The second‐order reaction rate constant (k₂) of MPDL and the heat of CO₂ absorption (–ΔH_abs) into aqueous MPDL solutions were evaluated as well. Based on the comparison with some conventional amines, MPDL revealed a high‐equilibrium CO₂ loading, reasonably fast absorption rate when compared with other tertiary amines, and a low energy requirement for regeneration. It may, therefore, be considered to be an alternative solvent for CO₂ capture. © 2017 American Institute of Chemical Engineers AIChE J, 63: 3395–3403, 2017     

Absorption of carbon dioxide in piperazine activated concentrated aqueous 2-amino-2-methyl-1-propanol solvent

In this work new experimental data on the rate of absorption of CO₂ into piperazine (PZ) activated concentrated aqueous solutions of 2-amino-2-methyl-1-propanol (AMP) over the temperature range 303–323 K are presented. The absorption experiments have been carried out in a wetted wall contactor over CO₂ partial pressure range of 5–15 kPa. PZ is used as a rate activator with a concentration ranging from 2 to 8 wt% keeping the total amine concentration in the solution at 40 wt%. The physical properties such as density and viscosity of concentrated aqueous AMP+PZ, as well as physical solubility of CO₂ in concentrated aqueous AMP+PZ, are also measured. New experimental data on vapor liquid equilibrium (VLE) of CO₂ in these concentrated aqueous solutions of AMP+PZ in the temperature range of 303–323 K have also been presented. The VLE measurements are carried out in an equilibrium cell in CO₂ pressure range of 0.1–140 kPa. A thermodynamic model based on electrolyte non-random two-liquid (eNRTL) theory is used to represent the VLE of CO₂ in aqueous AMP+PZ. Liquid phase speciations are estimated considering the nonideality of concentrated solutions of the amines and the calculated activity coefficients by eNRTL model. The CO₂ absorption in the aqueous amine solutions is described by a combined mass transfer-reaction kinetics model developed according to Higbie's penetration theory. The model predictions have been found to be in good agreement with the experimental results of the rates of absorptions of CO₂ into aqueous AMP+PZ.     

Absorption of Carbon Dioxide into Ionic Liquid of 2-Hydroxy Ethylammonium Lactate

Abstract

Absorption of carbon dioxide into organic solvents such as DMA, NMP, DMSO, and DMF with the 2-hydroxy ethylammonium lactate (HEAL) ionic liquid was investigated using a batch stirred tank with a plane of gas-liquid interface in a range of 0–2.0 kmol/m³ of HEAL and 298–318 K at 101.3 kPa. The absorption of CO₂ was analyzed with the film model accompanied by the zwitterion mechanism of CO₂ with HEAL. The proposed model fits the experimental data of the enhancement factor due to the ready, chemical absorption of CO₂ in different solvents, temperatures, and HEAL concentrations. The reaction rate constant of CO₂ with HEAL was correlated linearly with the solubility parameter of the solvent.     

Simultaneous Absorption of Carbon Dioxide and Sulfur Dioxide into Aqueous 2-Amino-2-Methy-1-Propanol

Abstract

Carbon dioxide and sulfur dioxide were simultaneously absorbed into aqueous 2-amino-2-methyl-1-propanol (AMP) in a stirred semi-batch tank with a planar gas-liquid interface within a range of 0–4.0 kmol/m³ of AMP, 0.03–0.3 mole fraction of CO₂, 0.005–2 mole fraction of SO₂, and 298–318 K. Absorption data of each gas in the CO₂-AMP and SO₂-AMP systems are obtained to verify their reaction regimes, based on film theory, respectively, which are used to analyze the simultaneous absorption mechanisms of CO₂ and SO₂ in the CO₂-SO₂-AMP systems. The measured absorption rates of CO₂ and SO₂ are compared to those formulated by an approximate solution of the mass balances with simultaneous reactions.     

Efficient pressure swing adsorption for improving H<Subscript>2</Subscript> recovery in precombustion CO<Subscript>2</Subscript> capture

An efficient design for pressure swing adsorption (PSA) operations is introduced for CO₂ capture in the pre-combustion process to improve H₂ recovery and CO₂ purity at a low energy consumption. The proposed PSA sequence increases the H₂ recovery by introducing a purge step which uses a recycle of CO₂-rich stream and a pressure equalizing step. The H₂ recovery from the syngas can be increased over 98% by providing a sufficient purge flow of 48.8% of the initial syngas feeding rate. The bed size (375m³/(kmol CO₂/s)) and the energy consumption for the compression of recycled CO₂-rich gas (6 kW/(mol CO₂/s)) are much smaller than those of other PSA processes that have a CO₂ compression system to increase the product purity and recovery.     

SOLUBILITY OF CO2AND H2S IN A MIXED SOLVENT

Mixed solvents are a combination of chemical and physical solvents and have some advantages over traditional treating solvents for the removal of acid gases from gas streams. The solubility of H₂S and CO₂in a mixed solvent consisting of AMP (2-amino-2-methyl-l-propanol), sulfolane, and water has been measured at 40 and 100°C at partial pressures of the acid gas to 6000 kPa. The solubility in the mixed solvent was compared with the solubility in an aqueous solution of equivalent amine concentration. At solution loadings less than 1 mol acid gas/mol amine, the solubility of the acid gas is lower in the mixed solvent than in the corresponding amine solvent. At higher loadings, the trend is reversed and the solubility is greater in the mixed solvent. The results are rationalized in terms of the effect of the physical solvent component on the chemical reaction and physical vapor-liquid equilibria. The solubility model of Deshmukh and Mather was used to correlate the data.