Synthesis of nickel catalysts supported on Zr-doped ordered mesoporous Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and their catalytic performance for low-temperature CO<Subscript>2</Subscript> reforming of CH<Subscript>4</Subscript>

A series of Zr-doped ordered mesoporous Al₂O₃ with various Zr contents were synthesized by evaporation-induced self-assembly strategy and the Ni-based catalysts supported on these Al₂O₃ materials were prepared by impregnation method. These catalysts with large specific surface area, big pore volume, uniform pore size possess excellent catalytic performance for the low-temperature carbon dioxide reforming of methane. The activities of these catalysts were tested in carbon dioxide reforming of methane reaction with temperature increasing from 500 to 650?°C and the stabilities of these catalysts were evaluated for long time reaction at 650?°C. It was found that when Zr/(Zr?+?Al) molar ratio?=?0.5%, the Ni/0.5ZrO₂–Al₂O₃ catalyst showed the highest activity, and exhibited superior stabilization compared to the Ni-based catalyst supported on traditional ordered mesoporous Al₂O₃. The “confinement effect” from mesoporous channels of alumina matrix is helpful to stabilize the Ni nanoparticles. As a promoter, Zr could stabilize the ordered mesoporous framework by reacting with Al₂O₃ to form ZrO₂–Al₂O₃ solid solution. Since ZrO₂ enhances the dissociation of carbon dioxide, more oxygen intermediates are given to remove the carbon formed during the reaction.     

Preparing and studying Pt/WO<Subscript>3</Subscript>/ZrO<Subscript>2</Subscript> catalysts for the isomerization of <Emphasis Type="Italic">n</Emphasis>-heptane

The effect of the temperature of WO₃/ZrO₂ support calcination in the range of 700–1000°C on the phase composition, acid, and catalytic properties of Pt/WO₃/ZrO₂ catalysts is studied. Using ammonia TPD, it is found that calcination in the temperature range of 850–950°C results in the formation of strong acid sites that increase the yield of the target products of the reaction of n-heptane isomerization: high octane di- and trimethylsubstituted isomers. DRIFT is used to determine the role of catalyst calcination in an air flow plays in the formation of charged platinum atoms, which results in higher catalyst activity.     

A Novel Process for Renewable Methane Production: Combining Direct Air Capture by K<Subscript>2</Subscript>CO<Subscript>3</Subscript>/Alumina Sorbent with CO<Subscript>2</Subscript> Methanation over Ru/Alumina Catalyst

CO₂ methanation over supported ruthenium catalysts is considered to be a promising process for carbon capture and utilization and power-to-gas technologies. In this work 4% Ru/Al₂O₃ catalyst was synthesized by impregnation of the support with an aqueous solution of Ru(OH)Cl₃, followed by liquid phase reduction using NaBH₄ and gas phase activation using the stoichiometric mixture of CO₂ and H₂ (1:4). Kinetics of CO₂ methanation reaction over the Ru/Al₂O₃ catalyst was studied in a perfectly mixed reactor at temperatures from 200 to 300 °C. The results showed that dependence of the specific activity of the catalyst on temperature followed the Arrhenius law. CO₂ conversion to methane was shown to depend on temperature, water vapor pressure and CO₂:H₂ ratio in the gas mixture. The Ru/Al₂O₃ catalyst was later tested together with the K₂CO₃/Al₂O₃ composite sorbent in the novel direct air capture/methanation process, which combined in one reactor consecutive steps of CO₂ adsorption from the air at room temperature and CO₂ desorption/methanation in H₂ flow at 300 or 350 °C. It was demonstrated that the amount of desorbed CO₂ was practically the same for both temperatures used, while the total conversion of carbon dioxide to methane was 94.2–94.6% at 300 °C and 96.1–96.5% at 350 °C.     

Preparation of Cu/ZnO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst under microwave irradiation for slurry methanol synthesis

Cu/ZnO/Al₂O₃ catalysts with Cu/Zn/Al ratios of 6/3/1 were precipitated and aged by conventional and microwave heating methods and tested in the slurry phase reactor for methanol synthesis. The effect of technological condition of precipitation and aging process under microwave irradiation on the catalytic performance was investigated to optimize the preparing condition of Cu/ZnO/Al₂O₃ catalyst. The results showed that the microwave irradiation during precipitation process could improve the activity of the catalyst, but had little effect on the stability. While the microwave irradiation during aging process has a great benefit to both the activity and stability of the catalyst, the catalyst aged at 80°C for 1 h under microwave irradiation possessed higher methanol space time yield (STY) and more stable catalytic activity. The activity and stability of the catalyst was further enhanced when microwave irradiation was used in both precipitation and aging processes; the optimized condition for the catalyst precursor preparation was precipitation at 60°C and aging at 80°C under microwave irradiation.     

Ni-Co bimetallic catalyst for CH<Subscript>4</Subscript> reforming with CO<Subscript>2</Subscript>

A co-precipitation method was employed to prepare Ni/Al₂O₃-ZrO₂, Co/Al₂ O₃-ZrO₂ and Ni-Co/Al₂O₃-ZrO₂ catalysts. Their properties were characterized by N₂ adsorption (BET), thermogravimetric analysis (TGA), temperature-programmed reduction (TPR), temperature-programmed desorption (CO₂-TPD), and temperature-programmed surface reaction (CH₄-TPSR and CO₂-TPSR). Ni-Co/Al₂O₃-ZrO₂ bimetallic catalyst has good performance in the reduction of active components Ni, Co and CO₂ adsorption. Compared with mono-metallic catalyst, bimetallic catalyst could provide more active sites and CO₂ adsorption sites (C + CO₂ = 2CO) for the methane-reforming reaction, and a more appropriate force formed between active components and composite support (SMSI) for the catalytic reaction. According to the CH₄-CO₂-TPSR, there were 80.9% and 81.5% higher CH₄ and CO₂ conversion over Ni-Co/Al₂O₃-ZrO₂ catalyst, and its better resistance to carbon deposition, less than 0.5% of coke after 4 h reaction, was found by TGA. The high activity and excellent anti-coking of the Ni-Co/Al₂O₃-ZrO₂ catalyst were closely related to the synergy between Ni and Co active metal, the strong metal-support interaction and the use of composite support.     

CO<Subscript>2</Subscript> methanation and co-methanation of CO and CO<Subscript>2</Subscript> over Mn-promoted Ni/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

A series of Mn-promoted 15 wt-% Ni/Al₂O₃ catalysts were prepared by an incipient wetness impregnation method. The effect of the Mn content on the activity of the Ni/Al₂O₃ catalysts for CO₂ methanation and the comethanation of CO and CO₂ in a fixed-bed reactor was investigated. The catalysts were characterized by N2 physisorption, hydrogen temperature-programmed reduction and desorption, carbon dioxide temperature-programmed desorption, X-ray diffraction and highresolution transmission electron microscopy. The presence of Mn increased the number of CO₂ adsorption sites and inhibited Ni particle agglomeration due to improved Ni dispersion and weakened interactions between the nickel species and the support. The Mn-promoted 15 wt-% Ni/Al₂O₃ catalysts had improved CO₂ methanation activity especially at low temperatures (250 to 400 °C). The Mn content was varied from 0.86% to 2.54% and the best CO₂ conversion was achieved with the 1.71Mn-Ni/Al₂O₃ catalyst. The co-methanation tests on the 1.71Mn-Ni/Al₂O₃ catalyst indicated that adding Mn markedly enhanced the CO₂ methanation activity especially at low temperatures but it had little influence on the CO methanation performance. CO₂ methanation was more sensitive to the reaction temperature and the space velocity than the CO methanation in the co-methanation process.

Open image in new window

     

Catalytic activity of Pd/Al2O3 toward the combustion of methane

This work focuses on the improving of the activities and stabilities of Pd/Al₂O₃ catalysts for lean methane catalytic combustion. The influence of preparation conditions on performance of Pd/Al₂O₃ catalyst has been studied. Results showed that excellent performance of the catalyst was attributed to high hydrothermal stability at the support calcination temperature of 1100 °C. In addition, the catalytic activity was enhanced due to high dispersion of active species at lower catalyst calcination temperature. The catalysts were studied by XPS analysis. Results showed that the active phase of Pd/Al₂O₃ was Pd or Pd/PdO mixture. And the state transformation of Pd species resulted in the deactivation of Pd/Al₂O₃.     

Upgrading of pyrolysis bio-oil using WO<Subscript>3</Subscript>/ZrO<Subscript>2</Subscript> and Amberlyst catalysts: Evaluation of acid number and viscosity

Tungstated zirconia (WO₃/ZrO₂ with WO₃ loadings of 9.9 (WZ9.9), 15.5 (WZ15.5), and 15.7 wt% (WZ15.7)) and Amberlyst (15, 35, 36, 39 and 45) catalysts were employed to upgrade pyrolysis bio-oil of acacia sawdust through an esterification reaction using methanol at atmospheric pressure and room temperature or 80 °C. The upgrading efficiency was evaluated by measuring the total acid number (TAN) and viscosity. The viscosity and TAN of the resulting upgraded bio-oil were found to be dependent on the calcination temperature of the WO₃/ZrO₂ catalysts. At room temperature, the largest decrease in viscosity and TAN of the bio-oil and methanol mixture was obtained using WZ9.9 tungstated zirconia calcined at 900 °C. An increase in reaction temperature to 80 °C improved the flowability and TAN of the methanol-added bio-oil using WZ9.9 activated at 900 °C. The product distribution of the bio-oil upgraded using methanol revealed esterification to be the dominant reaction pathway under the reaction conditions of this study. When the ether extracted bio-oil was upgraded at 80 °C using methanol over catalysts, the Amberlyst catalysts were found more effective than tungstated zirconia catalysts in enhancing the esterification reaction and reducing TAN.     

Reductive amination of ethanol to ethylamines over Ni/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Ni(x)/Al₂O₃ (x=wt%) catalysts with Ni loadings of 5–25 wt% were prepared via a wet impregnation method on an γ-Al₂O₃ support and subsequently applied in the reductive amination of ethanol to ethylamines. Among the various catalysts prepared, Ni(10)/Al₂O₃ exhibited the highest metal dispersion and the smallest Ni particle size, resulting in the highest catalytic performance. To reveal the effects of reaction parameters, a reductive amination process was performed by varying the reaction temperature (T), weight hourly space velocity (WHSV), and NH₃ and H₂ partial pressures in the reactions. In addition, on/off experiments for NH₃ and H₂ were also carried out. In the absence of NH₃ in the reactant stream, the ethanol conversion and selectivities towards the different ethylamine products were significantly reduced, while the selectivity to ethylene was dominant due to the dehydration of ethanol. In contrast, in the absence of H₂, the selectivity to acetonitrile significantly increased due to dehydrogenation of the imine intermediate. Although a small amount of catalyst deactivation was observed in the conversion of ethanol up to 10 h on stream due to the formation of nickel nitride, the Ni(10)/Al₂O₃ catalyst exhibited stable catalytic performance over 90 h under the optimized reaction conditions (i.e., T=190 °C, WHSV=0.9 h^?1, and EtOH/NH₃/H₂ molar ratio=1/1/6).     

Direct synthesis of hydrogen peroxide from hydrogen and oxygen over palladium catalyst supported on SO<Subscript>3</Subscript>H-functionalized MCF silica: Effect of calcination temperature of mesostructured cellular foam silica

Palladium catalysts supported on SO₃H-functionalized MCF silica (Pd/SO₃H-MCF-T (T=450, 550, 650, 750, 850, and 950)) were prepared with a variation of calcination temperature (T, °C) of MCF silica. They were then applied to the direct synthesis of hydrogen peroxide from hydrogen and oxygen. Conversion of hydrogen, selectivity for hydrogen peroxide, and yield for hydrogen peroxide showed volcano-shaped curves with respect to calcination temperature of MCF silica. Yield for hydrogen peroxide increased with increasing acid density of Pd/SO₃H-MCF-T catalysts. Thus, acid density of Pd/SO₃H-MCF-T catalysts played an important role in determining the catalytic performance in the direct synthesis of hydrogen peroxide. Pd/SO₃H-MCF-T catalysts efficiently served as an acid source and as an active metal catalyst in the direct synthesis of hydrogen peroxide.     

Visible light-irradiated degradation of alachlor on Fe-TiO<Subscript>2</Subscript> with assistance of H<Subscript>2</Subscript>O<Subscript>2</Subscript>

0.1 Fe/Ti mole ratio of Fe-TiO₂ catalysts were synthesized via solvothermal method and calcined at various temperatures: 300, 400, and 500 °C. The calcined catalysts were characterized by XRD, N₂-adsorption-desorption, UV-DRS, XRF, and Zeta potential and tested for photocatalytic degradation of alachlor under visible light. The calcined catalysts consisted only of anatase phase. The BET specific surface area decreased with the calcination temperatures. The doping Fe ion induced a red shift of absorption capacity from UV to the visible region. The Fe-TiO₂ calcined at 400 °C showed the highest photocatalytic activity on degradation of alachlor with assistance of 30 mM H₂O₂ at pH 3 under visible light irradiation. The degradation fitted well with Langmuir-Hinshelwood model that gave adsorption coefficient and the reaction rate constant of 0.683 L mg⁻¹ and 0.136 mg/L·min, respectively.     

Ni/La<Subscript>2</Subscript>O<Subscript>3</Subscript>-ZrO<Subscript>2</Subscript> catalyst for hydrogen production from steam reforming of acetic acid as a model compound of bio-oil

Hydrogen production from steam reforming of acetic acid was investigated over Ni/La₂O₃-ZrO₂ catalyst. A series of Ni/La₂O₃-ZrO₂ catalysts were synthesized by sol-gel method coupled with wet impregnation, which was characterized by XRD, BET, TEM, EDS, TG, SEM and TPR. Catalytic activity of Ni/La₂O₃-ZrO₂ was evaluated by steam reforming of acetic acid at the temperature range of 550-750 °C. The tetragonal phase La_0.1Zr_0.9O_1.95 is formed through the doping of La₂O₃ into the ZrO₂ lattice and nickel species are highly dispersed on the support with high specific surface area. H₂ yield and CO₂ yield of Ni/La₂O₃-ZrO₂ catalyst with 15%wt Ni reaches 89.27% and 80.41% at 600 °C, respectively, which is attributed to high BET surface area and sufficient Ni active sites in strong interaction with the support. 15%wt Ni supported on La₂O₃-ZrO₂ catalyst maintains relatively stable catalytic activities for a period of 20 h.     

Aqueous-Phase Hydrogenolysis of Glycerol to 1,3-propanediol Over Pt-H<Subscript>4</Subscript>SiW<Subscript>12</Subscript>O<Subscript>40</Subscript>/SiO<Subscript>2</Subscript>

Abstract  

Hydrogenolysis of glycerol to 1,3-propanediol in aqueous-phase was investigated over Pt-H₄SiW₁₂O₄₀/SiO₂ bi-functional catalysts with different H₄SiW₁₂O₄₀ (HSiW) loading. Among them, Pt-15HSiW/SiO₂ showed superior performance due to the good dispersion of Pt and appropriate acidity. It is found that Br?nsted acid sites facilitate to produce 1,3-PDO selectively confirmed by Py-IR. The effects of weight hourly space velocity, reaction temperature and hydrogen pressure were also examined. The optimized Pt-HSiW/SiO₂ catalyst showed a 31.4% yield of 1,3-propanediol with glycerol conversion of 81.2% at 200 °C and 6 MPa.     

Effect of Fe<Superscript>3+</Superscript> doping on the performance of TiO<Subscript>2</Subscript> mechanocoated alumina bead photocatalysts

Ferric ion was introduced to the commercial photocatalyst P25 (Degussa) by ultrasonic wet impregnation technique. The concentration of the dopant was varied from 0.0 to 3.0% Fe/Ti ratio. The doped TiO₂ was then loaded to alumina balls using mechanical coating technique and followed by calcination in air at 400, 450, 500 and 550 °C. The fabricated photocatalyst was characterized by X-ray diffraction, N₂ adsorption-desorption isotherms, scanning electron microscopy, UV-Vis diffuse reflectance spectroscopy, X-ray adsorption near edge structure and photoluminescence spectroscopy. The photocatalytic activity was tested by following the degradation of methylene blue (MB). It was found that the Fe³⁺ doped TiO₂/Al₂O₃ has a combination of anatase and rutile phase and free of iron oxide phases. The optimum calcination temperature is 400 °C with 0.1% Fe³⁺ concentration. The catalyst addresses the entrainment in photocatalytic reactors, eliminating the need for a post filtration process.     

Effect of H<Subscript>2</Subscript>O<Subscript>2</Subscript> modification of H<Subscript>3</Subscript>PW<Subscript>12</Subscript>O<Subscript>40</Subscript>@carbon for m-xylene oxidation to isophthalic acid

The production of isophthalic acid (IPA) from the oxidation of m-xylene (MX) by air is catalyzed by H₃PW₁₂O₄₀ (HPW) loaded on carbon and cobalt. We used H₂O₂ solution to oxidize the carbon to improve the catalytic activity of HPW@C catalyst. Experiments reveal that the best carbon sample is obtained by calcining the carbon at 700 °C for 4 h after being impregnated in the 3.75% H₂O₂ solution at 40 °C for 7 h. The surface characterization displays that the H₂O₂ modification leads to an increase in the acidic groups and a reduction in the basic groups on the carbon surface. The catalytic capability of the HPW@C catalyst depends on its surface chemical characteristics and physical property. The acidic groups play a more important part than the physical property. The MX conversion after 180 min reaction acquired by the HPW@C catalysts prepared from the activated carbon modified in the best condition is 3.81% over that obtained by the HPW@C catalysts prepared from the original carbon. The IPA produced by the former is 46.2% over that produced by the latter.     

A study on the catalytic performance of Pd/γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>, prepared by microwave calcination,in the direct synthesis of dimethylether

A series of Pd/γ-Al₂O₃ hybrid catalysts were prepared by impregnation and subsequent calcination under microwave irradiation. The catalysts were used for direct synthesis of dimethylether (DME) from syngas. The results show that calcination under microwave irradiation improved both the activity and selectivity of the catalysts for DME synthesis. The optimum power of the microwave was determined to be 420 W. Under such optimum conditions, CO conversion, DME selectivity and time space yield of DME were 60.1%, 67.0%, and 21.5 mmol·mL^?1·h^?1, respectively. Based on various characterizations such as nitrogen physisorption, X-ray diffraction, CO-temperature- programmed desorption, and Fourier transform infrared spectral analysis, the promotional effect of the microwave irradiation on the catalytic property was mainly attributed to both the higher dispersion of Pd and the significant increase in the adsorption on the CO-bridge of Pd. Microwave irradiation with very high power led to the increase in CO-bridge adsorption and thereby decreased the catalytic activity, whereas the coverage by metallic Pd of the active sites on acidic γ-Al₂O₃ significantly occurred under microwave irradiation with very low power, resulting in a decrease in the selectivity to DME.     

Effects of La<Subscript>2</Subscript>O<Subscript>3</Subscript> on ZrO<Subscript>2</Subscript> supported Ni catalysts for autothermal reforming of CH<Subscript>4</Subscript>

The effect of La₂O₃ content in Ni-La-Zr catalyst was investigated for the autothermal reforming (ATR) of CH₄. The catalysts were prepared by the coprecipitation method and had a mesoporous structure. Temperature programmed reduction (TPR) and X-ray photoelectron spectroscopy (XPS) indicated that a strong interaction developed between Ni species and the support with the addition of La₂O₃. Thermogravimetric analysis (TGA) and H₂-pulse chemisorption showed that the addition of La₂O₃ led to well dispersed NiO molecules on the support. Ni-La-Zr catalysts gave much higher CH₄ conversion than Ni-Zr catalyst. The Ni-La-Zr containing 3.2 wt% La₂O₃ showed the highest activity. The optimum conditions for maximal CH₄ conversion and H₂ yield were H₂O/CH₄=1.00, O₂/CH₄=0.75. Under these conditions, CH₄ conversion of 83% was achieved at 700 °C. In excess O₂ (O₂/CH₄>0.88), the catalytic activity was decreased due to sintering of the catalyst.     

Dynamics and Selectivity of N<Subscript>2</Subscript>O Formation/Reduction During Regeneration Phase of Pt-Based Catalysts

The formation of N₂O has been studied by means of isothermal lean-rich experiments at 150, 180 and 250 °C over Pt–Ba/Al₂O₃ and Pt/Al₂O₃ catalysts with H₂ and/or C₃H₆ as reductants. This allows to provide further insights on the mechanistic aspects of N₂O formation and on the influence of the storage component. Both gas phase analysis and surface species studies by operando FT-IR spectroscopy were performed. N₂O evolution is observed at both lean-to-rich (primary N₂O) and rich-to-lean (secondary N₂O) transitions. The production of both primary and secondary N₂O decreases by increasing the temperature. The presence of Ba markedly decreases secondary N₂O formation. FT-IR analysis shows the presence of adsorbed ammonia at the end of the rich phase only for Pt/Al₂O₃ catalyst. These results suggest that: (i) primary N₂O is formed when undissociated NO in the gas phase and partially reduced metal sites are present; (ii) secondary N₂O originates from reaction between adsorbed NH₃ and residual NO_x at the beginning of the lean phase. Moreover, N₂O reduction was studied performing temperature programming temperature experiments with H₂, NH₃ and C₃H₆ as reducing agents. The reduction is completely selective to nitrogen and occurs at temperature higher than 250 °C in the case of Pt–Ba/Al₂O₃ catalyst, while lower temperatures are detected for Pt/Al₂O₃ catalyst. The reactivity order of the reductants is the same for the two catalysts, being hydrogen the more efficient and propylene the less one. Having H₂ a high reactivity in the reduction of N₂O, it could react with N₂O when the regeneration front is developing. Moreover, also ammonia present downstream to the H₂ front could react with N₂O, even if the reaction with stored NO_x seems more efficient.     

CeO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> catalyst prepared by physical mixing for NH<Subscript>3</Subscript> selective catalytic reduction: Evidence about the migration of sulfates from TiO<Subscript>2</Subscript> to CeO<Subscript>2</Subscript> via simple calcination

A mechanical mixture of CeO₂ and TiO₂ powder with a small amount of sulfate was applied for the selective catalytic reduction (SCR) of NO with NH₃. After calcination at 500 oC, the mixed sample showed significantly enhanced activity and selectivity compared to the uncalcined one and, moreover, demonstrated even higher activity than the conventional V₂O₅/TiO₂ catalyst above 300 °C. Combined characterization results revealed that the main active sites were newly formed sulfate species on CeO₂, the number of which increased with calcination. Temperatureresolved DRIFT spectra provided convincing evidence about the migration of sulfate species from TiO₂ to CeO₂, as confirmed from the shift of v(S=O) band as a result of the mechanical mixing and the subsequent calcination.     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-ZrO<Subscript>2</Subscript> xerogel support on hydrogen production by steam reforming of LNG over Ni/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-ZrO<Subscript>2</Subscript> catalyst

An Al₂O₃-ZrO₂ xerogel (AZ-SG) was prepared by a sol-gel method for use as a support for a nickel catalyst. The Ni/AZ-SG catalyst was then prepared by an impregnation method, and was applied to hydrogen production by steam reforming of LNG. A nickel catalyst supported on commercial alumina (A-C) was also prepared (Ni/A-C) for comparison. The hydroxyl-rich surface of the AZ-SG support increased the dispersion of nickel species on the support during the calcination step. The formation of a surface nickel aluminate-like phase in the Ni/AZ-SG catalyst greatly enhanced the reducibility of the Ni/AZ-SG catalyst. The ZrO₂ in the AZ-SG support increased the adsorption of steam onto the support and the subsequent spillover of steam from the support to the active nickel sites in the Ni/AZ-SG catalyst. Both the high surface area and the well-developed mesoporosity of the Ni/AZ-SG catalyst improved the gasification of adsorbed surface hydrocarbons in the reaction. In the steam reforming of LNG, the Ni/AZ-SG catalyst showed a better catalytic performance than the Ni/A-C catalyst. Moreover, the Ni/AZ-SG catalyst showed strong resistance toward catalyst deactivation.