Tribological Properties of Polyvinyl Alcohol Hydrogel Reinforced with Nanometer Hydroxy Apatite

As a potential artificial cartilage material, the friction and wear properties of nano-hydroxy apatite （HA） particles filled poly （vinyl alcohol） hydrogel （PVA-H） composites sliding against stainless steel disk under water lubrication condition were studied by using a four ball tester. The worn surfaces were investigated by using a scanning electron microscope （SEM） to determine the wear mechanisms. Experimental results show that filling HA to PVA-H will slightly increase the friction coefficient of composites with the increasing of HA content under water lubrication condition. Meanwhile, HA particles can greatly reduce the wear mass loss of the PVA-H composites and enhance the load carrying capacity, the wear loss of the 1 wt% HA reinforced PVA-H composites can be decreased by 30 percent under 2.0 MPa to 50 percent under 0.5 MPa contact pressure. We also found that 2 wt% HA content of composites increase the wear mass loss under the same condition. SEM examination shows that the worn surface of low HA containing （1 wt%） composites are much smoother than that of pure PVA-H or high HA containing （2 wt%） composites under 1.5 MPa contact pressure. It is also found that there are big hole and big reunited HA particles in the surface of 2 wt% HA containing composites, which leads to deterioration of the surface of samples under higher loads in water lubrication. These results may be useful in the tribological design of artificial articular cartilage material.     

Tribological Properties of Polyvinyl Mcohol Hydrogel Reinforced with Nanometer Hydroxy Apatite

As a potential artificial cartilage material,the friction and wear properties of nano-hydroxy apatite(HA)particles filled poly(vinyl alcohol)hydrogel(PVA-H)composites sliding against stainless steel disk under water lubrication condition were studied by using a four ball tester.The worn surfaces were investigated by using a scanning electron microscope(SEM)to determine the wear mechanisms.Experimental results show that filling HA to PVA-H will slightly increase the friction coefficient of composites with the increasing of HA content under water lubrication condition.Meanwhile,HA particles can greatly reduce the wear mass loss of the PVA-H composites and enhance the load carrying capacity,the wear loss of the 1 wt% HA reinforced PVA-H composites can be decreased by 30 percent under 2.0 MPa to 50 percent under 0.5 MPa contact pressure.We also found that 2 wt% HA content of composites increase the wear mass loss under the same condition.SEM examination shows that the worn surface of low HA containing(1 wt%)composites are much smoother than that of pure PVA-H or high HA containing(2 wt%)composites under 1.5 MPa contact pressure.It is also found that there are big hole and big reunited HA particles in the surface of 2 wt% HA containing composites,which leads to deterioration of the surface of samples under higher loads in water lubrication.These results may be useful in the tribological design of artificial articular cartilage material.     

Research on the friction and wear mechanism of Poly(vinyl alcohol)/hydroxylapatite composite hydrogel

Poly(vinyl alcohol)/Hydroxylapatite (PVA/HA) composite hydrogel was prepared with poly(vinyl alcohol) and hydroxylapatite as raw materials, using the method of repeated freezing and thawing. The morphologies of PVA/HA composite hydrogel were observed by means of high-accuracy 3D profiler and scanning electron microscope (SEM). The compressive elastic modulus and the stress relaxation characteristics of PVA/HA composite hydrogel were measured using the flat-head cylinder indenter. The friction and wear tests between PVA/HA composite hydrogel and bovine knee articular cartilage were performed on the micro-tribometer. The worn morphologies of PVA/HA composite hydrogel were observed with environmental scanning electron microscope (ESEM). The results showed that PVA/HA composite hydrogel has the cross-link network microstructure which is similar to that of the natural bovine knee articular cartilages. With the increase of freezing-thawing cycles and the HA content, the degree of cross-link and the crystallization of PVA/HA composite hydrogel both increase, the elastic modulus increases evidently, the rate of stress relaxation is improved and the value of balance stress decreases. The friction coefficient decreases with the increase of the freezing-thawing cycles and the HA content. The more the freezing-thawing cycles are, the earlier the friction coefficient reaches the stable balance value. The friction deformation depth between PVA/HA composite hydrogel and bovine knee articular cartilage is inversely proportional to freezing-thawing cycles and the HA content. The main wear mechanisms of PVA/HA composite hydrogel are plastic flowing and adhesive flaking. The wear severity degree decreases with the increase of freezing-thawing cycles and the HA content. Supported by Key Program of the National Natural Science Foundation of China (Grant No. 50535050), Program for New Century Excellent Talents in University (Grant No. NCET-06-0479) and Natural Science Foundation of Jiangsu Province (Grant No. BK2005403)     

QPQ表面疏松层纯磨损试验研究

在M-2000型磨损试验机上进行纯磨损试验,研究了QPQ表面改性层在浸油擦干后的滑动干摩擦磨损过程。根据磨损曲线和摩擦系数的变化,发现其摩擦磨损过程存在一个干摩擦向边界摩擦过渡的亚稳定阶段,稳定阶段的磨损率和摩擦系数仅为未浸油干摩擦磨损试验时的三分之一。利用SEM分析各阶段磨损表面形貌,QPQ表面改性层磨合阶段的主要磨损机理为黏着磨损,亚稳定和稳定阶段对应的磨损机理为显微切削和划伤。试验结果表明,QPQ表面改性层外表面存在一定程度的疏松层可以储存润滑油,降低摩擦因数,避免或减轻了黏着磨损及磨粒磨损。     

纳米填料增强UHMWPE–橡胶水润滑摩擦学性能

为了研究水润滑条件下试验载荷和速度对纳米填料（Nano-SiC）改性超高分子量聚乙烯（UHMWPE）/橡胶复合材料摩擦学性能的影响,通过高温混炼、热压成型制备Nano-SiC辅以聚四氟乙烯（PTFE）填充改性UHMWPE/橡胶复合材料。采用MRH-3型环-块摩擦实验机探究四种不同载荷条件下改性复合材料的摩擦磨损性能,采用光学显微镜（OM）、扫描电子显微镜（SEM）和非接触光学三维轮廓仪对试样微观磨损表面形貌分析,从微观层面探究改性复合材料的摩擦机理。试验结果表明：在定载变速条件下,速度由0.02m/s升到3.59m/s时,改性复合材料的动摩擦系数波动幅度与静摩擦系数均呈现大幅下降趋势,粘-滑现象（Stick-Slip Phenomenon）减弱,摩擦系数波动归于平稳;试验载荷和纳米粒子含量的变化与试样摩擦磨损程度呈负相关,在水润滑条件下,随着纳米粒子含量增加,摩擦系数与磨损率均出现明显降低,填充比例为5%的复合材料摩擦学性能最佳,摩擦系数整体较UHMWPE/橡胶材料降低35%,磨损率降低46.6%,磨损表面形貌也随之发生改变;随着载荷的增加,复合材料的磨损率从1.25×10-6mm3/(Nm)降至0.4×10-6mm3/(Nm)。Nano-SiC的含量与工况载荷压力对摩擦磨损均存在一定影响,即填充适量Nano-SiC的UHMWPE/橡胶复合材料与一定工况压力下的对偶钢环组成的摩擦配副能改善摩擦环境,减轻粘-滑现象,有利于减小材料的磨损。     

Tribological Behavior of Nano-ZrO_2 Reinforced PTFE-PPS Composites

Polytetrafluoroethylene(PTFE) is a commonly used seal material for oil-free engine that is well known for its excellent tribological properties. In this work, the nano-ZrO_2 particles were used as the friction modifiers to improve the friction and wear performance of PTFE-PPS composites. The friction and wear characteristics of PTFE/PPS-nano-ZrO_2 composites were investigated by a block-on-ring tester under dry friction sliding condition. The worn surfaces, counterpart transfer films and wear debris were studied by scanning electron microscopy and X-ray photoelectron spectroscopy. It was found that the increase of nanoZrO_2 content could effectively reduce the coefficient of friction and enhance the anti-wear ability of PTFEPPS composites. Especially, the best tribological properties of the composites were obtained when the particle content of nano-ZrO_2 was 10 vol%, the anti-wear performance of composite is 195 times better than that of the unfilled PTFE-PPS composite. Under different conditions, the coefficient of friction of PTFE/PPS-nano-ZrO_2 composites was more affected by the applied load while the wear rate was more affected by the sliding velocity.     

GCr15球-盘点接触摩擦副的滑滚摩擦磨损特性研究

选用GCr15钢盘和GCr15球作为摩擦副,在NGY‐6纳米润滑膜测量仪上开展球‐盘点接触摩擦副在润滑状态下的滑滚摩擦磨损实验,研究不同接触应力、钢球转速、滑滚比等参数对摩擦副的摩擦因数、磨损形貌的影响规律．结果表明：当接触应力和钢球转速一定时,摩擦因数随着滑滚比的增大而逐渐增加后达到稳定状态;当滑滚比一定时,摩擦因数随接触应力的增大而逐渐增大;当钢球转速低于300 r／min时,摩擦因数随着钢球转速的增大而减小;当钢球转速高于300 r／min、接触应力大于0．84 GPa时,摩擦因数随着钢球转速的增大而呈增大趋势．Stribeck曲线表明：当滑滚比为0．01时,摩擦副处于流体动压润滑状态;当滑滚比为0．03时,润滑状态随Sommerfield参数的增加而从边界润滑过渡到混合润滑;当滑滚比分别为0．05、0．1、0．3、0．5时,润滑状态为边界润滑．滑滚比较小时,磨损机制以疲劳磨损为主,随着滑滚比的增大,磨损机制转变为磨粒磨损．     

纳米羟基磷灰石复合陶瓷生物摩擦学行为研究

采用沉淀法合成了纳米羟基磷灰石（HA）粉体，无压烧结工艺制备了HA／PSZ陶瓷复合材料．利用材料试验分析系统（MTS）和纳米硬度分析测试系统（Triboindenter）测定了复合材料的宏观和微观力学性能，用销盘式摩擦磨损试验机考察了血浆润滑条件下复合材料的生物摩擦学性能，探讨了力学性能与摩擦学性能之间的关系．结果表明，无压烧结HA／PSZ复合陶瓷材料断裂韧性比纯HA陶瓷提高近2．7倍，弯曲强度提高近1倍．纳米硬度最高值为10．6GPa，纳米弹性模量为156．OGPa．血浆润滑条件下，HA／PSZ陶瓷和UHMWPE摩擦副的摩擦系数与HA的含量有关，UHMWPE的磨损率与HA／psz复合陶瓷摩擦副的硬度和断裂韧性存在反比关系．     

退火温度对7022铝合金干摩擦性能的影响

对7022铝合金的不同温度退火试样进行干滑动摩擦磨损试验,用扫描电镜、显微硬度测试仪和三维形貌仪分析各试样的磨损机制.结果表明,退火温度对材料的显微硬度和摩擦磨损性能有明显影响,退火温度在200℃时,材料显微硬度和摩擦磨损性能最好,此温度下材料得到完全再结晶,且晶粒细化;摩擦磨损性能随着显微硬度的提高而减小.塑变磨损、磨粒磨损和疲劳磨损为7022铝合金的主要磨损机理.     

Nano K_2Ti_4O_9 Whisker Enhanced Solid Lubrication Coating for Cutting Application

1　IntroductionWiththedevelopmentofmanufactureindustry ,vari ouskindsofmachinesbringgreatconveniencetopeople’slife .Butalongwiththem ,resourcesexhaustionanden vironmentalpollutionhavebroughtsomenegativeeffectstohumanlife .Metalcuttingisthemainbranchofman…     

氟化镧对固体润滑粘结膜摩擦学性能的影响及其作用机理之研究

对于氟化镧（ＬａＦ３）对酚醛－环氧粘结的二硫化钠（ＭｏＳ２）干膜性能的影响进行了考察，并着重应用表面分析工具对其作用机理进行了研究。结果表明，与不含ＬａＦ３的干膜相比，当含有适量ＬａＦ３时，干膜的耐磨寿命明显增加。在摩擦过程中，ＬａＦ３减少了干腔中ＭｏＳ２的氧化趋势。     

The Wear Process of PTFE Coatings Under Vacuum Conditions

The wear process of PTFE coatings sliding against GCrlS-bearing steel ball under vacuum conditions was investigated, and the hardness of the PTFE coatings on both sides of wear track was measured. The experimental results showed that the friction coefficient of the PTFE coatings increases with the increase of sliding distance under different sliding velocities. And the friction coefficient of the PTFE coatings increases with the increase of sliding distance under different sliding loads. The wear rate of PTFE coatings decreases with the increase of sliding distance. And the majority of the wear produced during the whole wear process of PTFE coatings sliding against GCr-15 steel ball comes from the early period of friction. The hardness of PTFE coatings on both sides of wear track increases as the distance increases and distributes symmetrically around the wear track. Scanning electron microscope （SEM） was utilized to investigate the worn surface of PTFE coating, h was found that the worn surface of PTFE coating is characterized by sever plastic deformation and spalling of the PTFE coating. The edge of wear track is characterized by micro cracking.     

振动对纯碳、浸金属碳滑板载流磨损性能的影响

采用高速环-块式载流摩擦试验机,研究了纯碳和浸金属碳两种滑板材料在高速载流条件下的摩擦磨损行为。利用相关系数理论,对滑板振动加速度和电弧能量的相关性进行定量分析,发现滑板振动加速度和电弧能量之间存在着明显的相关性。试验结果表明：摩擦系数随着振动加速度的增加逐渐减小,两种滑板材料的磨损率随着振动加速度的增加均逐渐增大,且浸金属碳滑板的耐磨性比纯碳滑板好。随着振动的增大,电弧对两种滑板材料的侵蚀程度均明显加剧,浸金属碳滑板电弧侵蚀形式以层片状剥离为主;纯碳滑板以烧蚀坑和热应力裂纹为主。载流条件下,纯碳滑板导电性优于浸金属碳滑板。     

稀土化合物填充PA1010复合材料的摩擦学特性

采用热挤压注模方法制备了含不同稀土化合物如CeO2,LaF3,La2O3的尼龙1010（PA1010）复合材料。测定了复合材料的密度和硬度,在MM－200型环－块实验机上考察了其摩擦磨损性能,用光学显微镜观察了材料表面磨痕和转移膜形貌。研究结果发现,添加稀土化合物可改变PA1010的摩擦学性能,尤其是填充La2O3的PA1010复合材料的减摩、耐磨性能均最佳,PA1010的磨损主要表现为粘着、劳和逆性变形,其转移膜不连续,且有脱落现象,PA1010－15％La2O3复合材料的磨损主要为磨粒磨损,其转移膜致密光滑,薄而完整,这与其耐磨性最好的现象相一致。     

玻璃粉/尼龙1010复合材料摩擦学性能研究

将玻璃粉碎成微米级颗粒，作为增强材料，用硅烷偶联剂KH-550对玻璃粉进行表面处理，充填尼龙1010．制备了玻璃粉／尼龙1010复合材料，在环一块磨损试验机上研究了复合材料的摩擦学性能，使用邵氏硬度计测量了复合材料的硬度．借助SEM进行摩擦表面分析．试验结果表明：玻璃粉充填尼龙1010能降低复合材料的摩擦系数，础（玻璃粉）为25％时摩擦系数最小；w（玻璃粉）为20％时，磨损率仅为尼龙的18％．玻璃粉在一定含量的范围内能提高复合材料硬度．     

激光功率参数对GCr15钢组织和抗磨性能的影响

为研究不同激光功率参数对激光硬化后的最终显微组织、硬度和耐磨性的影响,应用宽带扫描技术进行了GCr15轴承钢激光强化处理试验,用光学显微镜和扫描电镜、x射线衍射仪等现代测试手段对GCr15轴承钢试样的显微组织和形貌尺寸特征进行了分析,磨损试验在MM200磨损试验机上进行.结果表明,激光参数变化所产生的显微组织变化造成了表面硬度值和磨损率的较大差异.激光功率大时,激光硬化层表面未溶碳化物量减少,使得表面马氏体中碳的质量分数增加,表面硬度增高.在干摩擦磨损过程中,激光改性层表面发生摩擦诱发马氏体相变.在干摩擦和油润滑两种条件下,激光功率越大,激光硬化层的抗磨损性越好.     

脉冲真空电弧离子镀沉积类金刚石薄膜的结构和力学性能研究

利用脉冲真空电孤离子镀技术在3Cr13不锈钢上制备了类金刚石(DLC)薄膜．通过Raman光谱分析了膜的结构特征，采用摩擦磨损试验机测试了薄膜在不同载荷下的摩擦系数，运用划痕仪研究了膜基的结合强度．结果表明：所镀制的薄膜具有典型类金刚石结构特征，膜中ID／IG为1．33；摩擦系数随着载荷的增大而减小，载荷为5N，转速120r／min时的摩擦系数为0．02；Ti过渡层的引入显著地提高了膜基结合力．     

Morphology and tribological properties of Ni/n-SiO_2 composite coatings by pulse-reverse current brush-plating

1INTRODUCTION Pulse reversecurrent(RC)platingisanew technologycomingwithpulsecurrent(PC)andre versecurrent.Onthisaspect,earlierstudiesmani festedthat[16],intheconditionofRC,theeffectofelectricdoublelayerwasrestrained,thecontrol ofcrystallinegrowthwasenfor…     

水环境下二硫化钼/聚四氟乙烯复合材料与石英玻璃的超润滑摩擦学特性

采用M-200型摩擦磨损试验机,对比研究了几种填充PTFE复合材料与石英玻璃对磨时,在水润滑、低速、较高载荷条件下的摩擦学特性。结果表明:在水润滑条件下,MoS2/PTFE复合材料与石英玻璃对磨时的摩擦系数可低于0.005,表现出超润滑摩擦特性,而且具有稳定的摩擦系数和很低的磨损率。石英玻璃所具有的优良表面特性和优异的亲水性是实现超润滑的关键。当添加高硬添料时,石英玻璃表面容易受到破坏,导致摩擦学性能下降。     

紧固件表面锰系磷化膜的制备及摩擦磨损性能

为了提高核主泵紧固件的摩擦磨损性能,采用三种磷化工艺在40Ni Cr Mo7钢表面制备了锰系磷化膜.采用多功能材料表面性能测试仪进行了往复摩擦磨损试验,并研究了在有无润滑条件下,不同工艺对磷化膜摩擦磨损性能的影响.采用扫描电子显微镜和能谱仪表征了磨损前后磷化膜表面的组织形貌和化学成分,并分析了其磨损失效机制.结果表明,通过工艺Ⅱ制备的磷化膜具有最优的摩擦磨损性能.磷化膜特有的孔隙结构具有储油能力,有利于改善其摩擦学性能.随着法向载荷的增加,磷化膜的塑性变形增大,抗剪切强度降低,且摩擦系数呈先缓慢下降后急剧上升的趋势.