The influence of fibre properties of the performance of glass-fibre-reinforced polyamide 6,6

We discuss the effect of fibre strength and diameter on the balance of mechanical properties of glass-reinforced polyamide 6,6. The results show that the elastic properties of injection-moulded short-glass-fibre-reinforced polyamide 6,6 are not strongly influenced by fibre diameter in the 10–17 micron range. The ultimate properties of these composites (strength and Izod impact behaviour) showed a clear dependence on fibre diameter and were increased by the presence of high-strength S-2 glass fibres. The relationship between the observed mechanical properties and the length, diameter and orientation of the fibres is explored. We have measured fibre length as a function of diameter in composites containing a single glass-reinforcement product and blends of two glass products. The reduction in glass-fibre length from glass-fibre production to final composite moulding has been followed step by step. The final composite mechanical properties, the fibre length, strength, diameter and orientation are all inter-related.     

A smart repair system for polymer matrix composites

The widespread use of polymer composites is still caveated with concerns about the loss in structural performance that can result from impact damage. Such events give rise to delaminations which may not be easily detectable by eye. This paper describes a technique for ‘smart’ repair of delaminations in polymer composites. This involves the filling of hollow fibres with a resin, which is released into the damaged area when the fibre is fractured. A two-part epoxy resin is used as the repair medium, the two components being diluted with solvent and infiltrated into different plies of a composite based on ‘Hollex’ S2-glass fibre. Compression strength after impact tests were used as a measure of the effectiveness of the repair technique, and a potential improvement was noted after application of heat and vacuum to the damaged composite. Resin release from the fibres was noted by microscopy. A more comprehensive study is required to verify the improvement in post-impact strength, and the use of larger internal diameter fibres would enhance the amount of resin released.     

The impact strength of fibre composites

Two models have been developed which predict the crack initiation energy, notched impact strength and unnotched impact strength of fibre composites. One is applicable to composites containing short fibres and the other to composites containing long fibres. Data obtained with randomly oriented short fibre composites were consistent with the one model. The other model has been verified using composites containing uniaxially oriented long fibres and long fibres oriented randomly in a plane. The success of the model demonstrates that the high notched impact strength with long fibres is due to the redistribution of stress away from the stress concentrating notch, the extra stress that can be held by the fibre relative to the matrix and the work required to pull fibres out of the matrix during crack propagation. The parameters which have been shown to control the fracture energy are composite modulus, fibre length, fibre volume fraction, effective fibre diameter, fibre tensile strength and the coefficient of friction during fibre pull-out from the matrix. The matrix toughness on the other hand usually has no effect at all for composites containing fibres randomly oriented in two dimensions and only a minor effect in exceptional cases. The shear strength of the fibre-matrix bond has only an indirect effect in that it controls the number of fibres which pull out rather than fracture.     

Effect of resin system on the mechanical properties and water absorption of kenaf fibre reinforced laminates

The objective of this study is to compare the mechanical and water absorption properties of kenaf (Hibiscus cannabinus L.) fibre reinforced laminates made of three different resin systems. The use of different resin systems is considered so that potentially complex and expensive fibre treatments are avoided. The resin systems used include a polyester, a vinyl ester and an epoxy. Laminates of 15%, 22.5% and 30% fibre volume fraction were manufactured by resin transfer moulding. The laminates were tested for strength and modulus under tensile and flexural loading. Additionally, tests were carried out on laminates to determine the impact energy, impact strength and water absorption. The results revealed that properties were affected in markedly different ways by the resin system and the fibre volume fraction. Polyester laminates showed good modulus and impact properties, epoxy laminates displayed good strength values and vinyl ester laminates exhibited good water absorption characteristics. Scanning electron microscope studies show that epoxy laminates fail by fibre fracture, polyester laminates by fibre pull-out and vinyl ester laminates by a combination of the two. A comparison between kenaf and glass laminates revealed that the specific tensile and flexural moduli of both laminates are comparable at the volume fraction of 15%. However, glass laminates have much better specific properties than the kenaf laminates at high fibre volume fractions for all three resins used.     

Hygromechanical properties of composites of crosslinked allylglycidyl-ether modified starch reinforced by wood fibres

In a previous work a new family of thermoset composites of allylglycidyl ether modified starch as matrix, an ethylene glycol dimethacrylate as cross-linker and a wood fibre as reinforcement were prepared. The aim of the present work was to study the hygromechanical properties of the new composites including density, dimensional stability in water, water uptake, stiffness, and ultimate strength in three-point bending. It was shown that the samples with a starch matrix of a high degree of substitution (DS = 2.3), HDS, absorbed less water, were more stable in water and had also higher stiffness and strength than corresponding composite samples with a starch matrix of low degree of substitution (DS = 1.3), LDS. Overall, the fibre addition improved water stability. An increased fibre content from 40 to 70% by weight had a negligible impact on the water uptake. An increase in fibre content did, however, improve the mechanical properties. The HDS-sample with highest fibre content, 70% by weight showed the highest Young’s modulus (3700 MPa) and strength (130 MPa), which are markedly higher compared with the samples based on the pure HDS matrix (Young’s modulus of 360 MPa and strength of 15 MPa). The measured Young’s modulus and tensile strength values were roughly one order of magnitude higher than earlier reported cellulosic fibre reinforced natural polymer composites.     

Flexural properties of hemp fibre reinforced polylactide and unsaturated polyester composites

In this work, flexural strength and flexural modulus of chemically treated random short and aligned long hemp fibre reinforced polylactide and unsaturated polyester composites were investigated over a range of fibre content (0-50 wt%). Flexural strength of the composites was found to decrease with increased fibre content; however, flexural modulus increased with increased fibre content. The reason for this decrease in flexural strength was found to be due to fibre defects (i.e. kinks) which could induce stress concentration points in the composites during flexural test, accordingly flexural strength decreased. Alkali and silane fibre treatments were found to improve flexural strength and flexural modulus which could be due to enhanced fibre/matrix adhesion.     

Polyoxymethylene composites with natural and cellulose fibres: Toughness and heat deflection temperature

Cellulose and abaca fibre reinforced polyoxymethylene (POM) composites were fabricated using an extrusion coating (double screw) compounding followed by injection moulding. The long cellulose or abaca fibres were dried online with an infrared dryer and impregnated fibre in matrix material by using a special extrusion die. The fibre loading in composites was 30 wt.%. The tensile properties, flexural properties, Charpy impact strength, falling weight impact strength, heat deflection temperature and dynamic mechanical properties were investigated for those composites. The fibre pull-outs, fibre matrix adhesion and cracks in composites were investigated by using scanning electron microscopy. It was observed that the tensile strength of composites was found to reduce by 18% for abaca fibre and increase by 90% for cellulose fibre in comparison to control POM. The flexural strength of composites was found to increase by 39% for abaca fibre and by 144% for cellulose fibre. Due to addition of abaca or cellulose fibre both modulus properties were found to increase 2-fold. The notched Charpy impact strength of cellulose fibre composites was 6-fold higher than that of control POM. The maximum impact resistance force was shorted out for cellulose fibre composites. The heat deflection temperature of abaca and cellulose fibre composites was observed to be 50 °C and 63 °C higher than for control POM respectively.     

Procedural influences on compression and injection moulded cellulose fibre-reinforced polylactide (PLA) composites: Influence of fibre loading,fibre length,fibre orientation and voids

The influence of fibre loading (20, 30, 40 mass%), fibre fineness, and the processing procedure (compression moulding – CM and injection moulding – IM) on the tensile and impact strength of lyocell/PLA composites was examined. The results revealed a significantly higher tensile and impact strength for CM composites compared to IM composites. An increase in strength up to a fibre loading of 40% was determined for CM composites, while for IM composites the highest values were measured at a fibre loading of 30%. Composites were investigated for their void content, fibre orientation, fibre length and process-induced fibre damage. A better fibre/matrix adhesion and compaction of IM composites was found while fibre orientation as well as mechanical properties of extracted fibres show no significant differences between CM and IM composites. The different mechanical characteristics of CM and IM samples are attributed predominantly to the fibre aspect ratio and the distribution of voids.     

Influence of the filament winding tension on physical and mechanical properties of reinforced composites

In this experimental investigation the influence of the applied tow tension during filament winding on the physical and mechanical properties of glass-fibre reinforced polymeric composite tubulars, was studied. Pressure retaining tubular products used in the transportation/storage of fluids are generally subjected to a variety of loading conditions during their service life; thus tubular specimens were tested under different biaxial loading ratios. The stress/strain response was recorded and functional and structural failure envelopes were developed. These envelopes indicate the leakage and final failure characteristics of the components, respectively. The mechanical properties were analysed in conjunction with the measured physical properties: ‘fibre volume fraction’ and ‘effective wall thickness’. Experimental findings demonstrate that the component strength depends on the degree of fibre tensioning. Under fibre-dominated loading conditions, higher winding tension leads to an improved resistance against failure of tubular components, whereas under matrix-dominated loading failure is delayed by reduced fibre tensioning.     

Effect of coupling agents on reinforcing potential of recycled carbon fibre for polypropylene composite

Polypropylene (PP) composites reinforced with recycled carbon fibre have been prepared through extrusion compounding and injection moulding. The reinforcing potential of the recycled fibre was increased by improving the interfacial adhesion between the fibre and PP matrix and this was done by the addition of maleic anhydride grafted polypropylene (MAPP) coupling agents. Three MAPP couplers with different molecular weights and maleic anhydride contents were considered. The effects on the mechanical properties of the composite were studied, and scanning electron microscopy (SEM) was used to study the fracture morphology of the tensile specimens. It was observed that with the addition of MAPP the interfacial adhesion was improved as fewer fibres were pulled-out and less debonding was seen. A microbond test was performed and a significant improvement in interfacial shear strength was measured. This resulted in composites with higher tensile and flexural strengths. The maximum strength was achieved from MAPP with the highest molecular weight. Increased modulus was also achieved with certain grades of MAPP. It was also found that the composite impact strength was improved significantly by MAPP, due to a higher compatibility between the fibre and matrix, which reduced crack initiation and propagation.     

An investigation on shape memory behaviours of hydro-epoxy/glass fibre composites

Shape-memory polymers (SMPs) have the capacity to return large strains by external stimuli. Among various SMPs, shape-memory epoxy has received considerable attention because of its superior mechanical and thermal properties as well as excellent shape-memory performance. In this study, short glass fibre-reinforced shape-memory hydro-epoxy composites are developed to improve further the mechanical property of shape-memory epoxy resin. The thermomechanical and shape-memory properties of the developed composite materials are investigated by dynamic mechanical analysis, bend test and shape recovery test. The results indicate that the glass modulus and bend strength of the developed composite materials initially increase and then slightly decrease with increasing short glass fibre content. The glass transition temperature of the developed composite materials does not change with increasing short glass fibre. When the short glass fibre content is less than 4.5 wt.%, full recovery can be observed after only several minutes at different temperatures. The shape-memory property of the composite materials is not affected greatly. However, when the short glass fibre content is more than 4.5 wt.%, the material would be destroyed after deformation.     

High performance hybrid PP and PLA biocomposites reinforced with short man-made cellulose fibres and softwood flour

This paper presents the research on hybrid thermoplastic biocomposites reinforced with a combination of short man-made cellulose fibres and softwood flour. The introduced short fibre composites are meant to be processed with injection moulding and may be an alternative to glass-fibre reinforced thermoplastics on account of their comparable specific strengths. The occurring positive hybrid effect enables to substitute up to half the weight of short fibre cellulose reinforcement with softwood flour without a significant reduction of material flexural strength. The flexural modulus of investigated hybrid biocomposites remained approximately at the same level, while impact strength was reduced with increasing softwood flour content. The proposed hybridisation leads to establishing biocomposites of suitable performance with competitive density, price and recycling possibilities in comparison to standard glass fibre reinforced counterparts. Moreover, the application of biobased polymers like polylactide as biocomposite matrix, contributes to the development of so called “green” high performance materials.     

An experimental study on the in situ strength of SiC fibre in unidirectional SiC/Al composites

In order to investigate the effect of strain rate and high temperature exposure on the mechanical properties of the fibre in the unidirectional fibre reinforced metal-matrix composite, in situ SiC fibre bundles are extracted from two kinds of SiC/Al composite wires, which are heat-treated at two different temperatures (exposed in the air at 400 and 600 °C for 40 min after composition). Tensile tests for these two fibre bundles are performed at different strain rates (quasi-static test: 0.001 s⁻¹, dynamic test: 200, 700, and 1200 s⁻¹) and the stress–strain curves are obtained. The experimental results show that their mechanical properties are rate-dependent, the modulus E, strength σ_b and unstable strain _b (the strain corresponding to σ_b) all increase with increasing strain rate. Compared with the mechanical properties of the original SiC fibre, those of the two in situ fibres degrade to some extent, the degradation of the in situ fibre extracted from the composite wire exposed at 600 °C (hereafter referred to as in situ fibre 2) is more serious than that of the in situ fibre extracted from the composite wire exposed at 400 °C (hereafter referred to as in situ fibre 1). The mechanism of the degradation is investigated. A bi-modal Weibull statistical constitutive equation is established to describe the stress–strain relationship of the two in situ fibre bundles. The simulated stress–strain curves agree well with the experimental results.     

Impact and fatigue behaviour of hemp fibre composites

A series of experiments has been carried out to characterize the residual tensile and fatigue properties following impact of non-woven hemp fibre mat reinforced polyester. Additionally, the degradation of tensile modulus during fatigue cycling has been studied and related to the damage accumulation. For comparison purposes, ±45° glass fibre reinforced polyester samples have also been subjected to similar tests. It was found necessary to apply a relatively high pressure to the hemp composite during the curing stage in order to ensure a high enough fibre fraction to provide a significant reinforcing effect. With similar fibre weight fractions, the hemp and glass reinforced materials exhibited similar static tensile properties and fatigue lifetimes. Although the slightly steeper S–N curve of the hemp based material indicated a higher rate of reduction in fatigue strength with increasing cycles, it remained above the S–N curve for the glass based material showing that it was able to withstand slightly higher cyclic stress levels for equivalent numbers of cycles. The major difference in mechanical performance was the poorer resistance of the hemp based composite to impact. Also, the hemp based material failed in a much more brittle manner, without any visible signs of damage, such as the matrix cracking that was seen in the glass fibre based composite. It was found that, if the fatigue lifetime data of impact damaged samples were normalized against the post-impact residual tensile strength, then all data points lay close to a common S–N curve. This implies that residual fatigue lifetimes of damaged samples could be predicted from knowledge of their residual strength and the S–N curve for undamaged material.     

Evaluation on the thermal and mechanical properties of HNT-toughened epoxy/carbon fibre composites

Halloysite nanotubes (HNT) were effectively incorporated into epoxy resin and used for infusion of carbon fibre textiles, resulting in epoxy/halloysite nanotube/carbon fibre (EP/HNT/CF) multi-scale composites. The distribution of nanotubes in the composites was examined by SEM. The thermomechanical properties of the composites were characterized by dynamic mechanical analyser (DMA). A 25% enhancement was recorded for the storage modulus of EP/HNT/CF composite in the glassy state. Moreover, the T_g of the laminates increased with the addition of HNT, and the values were even higher than the T_g of their matrix. Additionally, the Izod impact strength of the composites has been improved. These results indicate a synergistic effect between HNT and carbon fibres.     

Hierarchical composites reinforced with robust short sisal fibre preforms utilising bacterial cellulose as binder

A novel robust non-woven sisal fibre preform was manufactured using a papermaking process utilising nanosized bacterial cellulose (BC) as binder for the sisal fibres. It was found that BC provides significant mechanical strength to the sisal fibre preforms. This can be attributed to the high stiffness and strength of the BC network. Truly green non-woven fibre preform reinforced hierarchical composites were prepared by infusing the fibre preforms with acrylated epoxidised soybean oil (AESO) using vacuum assisted resin infusion, followed by thermal curing. Both the tensile and flexural properties of the hierarchical composites showed significant improvements over polyAESO and neat sisal fibre preform reinforced polyAESO. These results were corroborated by the thermo-mechanical behaviour of the (hierarchical) composites, which showed an increased storage modulus and enhanced fibre–matrix stress transfer. Micromechanical modelling was also performed on the (hierarchical) composites. By using BC as binder for short sisal fibres, added benefits such as the high Young’s modulus of BC, enhanced fibre–fibre and fibre–matrix stress transfer can be utilised in the resulting hierarchical composites.     

Carbon fibres: structure and mechanical properties

The microstructure of six types of acrylic-based and hydrated cellulose-based carbon fibres of strengths from 1650 to 6120 MPa and elastic moduli from 97 to 228 GPa were studied by scanning electron microscopy (SEM). A ‘microcomposite’ structure of carbon fibres studied consisting of quasi-amorphous (‘matrix’) and orientated fibrillar carbon was revealed. This led to a new model of the fibre structure. The analysis of results of testing different carbon fibres defines the elastic modulus of ‘matrix’ carbon, and shows plastic drawing of fibrils. The model describes the properties of fibres and predicts ways to improve the fibre properties.     

The influence of fibre length and concentration on the properties of glass fibre reinforced polypropylene: 7. Interface strength and fibre strain in injection moulded long fibre PP at high fibre content

The mechanical performance of injection moulded long glass fibre reinforced polypropylene with a glass fibre content in the range 0–73% by weight has been investigated. The composite modulus exhibited a linear dependence on fibre content over the full range of the study. Composite strength and impact resistance exhibited a maximum in performance in the 40–50% by weight reinforcement content range. The residual fibre length, average fibre orientation, interfacial shear strength, and fibre strain at composite failure in the samples have been characterised. These parameters were also found to be fibre concentration dependent. The interfacial shear strength was found to be influenced by both physical and chemical contributions. Theoretical calculations of the composite strength using the measured micromechanical parameters enabled the observed maximum in tensile strength to be well modelled.     

The influence of fibre length,diameter and concentration on the impact performance of long glass-fibre reinforced polyamide 6,6

Results of an investigation of the mechanical performance of injection moulded long glass-fibre reinforced polyamide 6,6 composites are presented. The glass-fibre content in these composites was varied over the range of 10–50% by weight using fibres with average diameters of 10, 14 and 17 μm. Impact testing was carried out at ?40, 23 and 80 °C on dry-as-moulded and boiling water conditioned samples. The results from these long fibre composites are compared with standard extrusion compounded short glass-fibre materials. Data on the influence of fibre diameter, fibre concentration, residual fibre length, hydrothermal conditioning and testing temperature on the composite performance in notched and unnotched pendulum impact tests and multiaxial instrumented impact tests are presented and discussed. All of the above parameters are shown to have significant influence on impact performance. However, the level of these effects is shown to depend on which type of impact test is being considered.     

The influence of fibre length and concentration on the properties of glass fibre reinforced polypropylene. 6. The properties of injection moulded long fibre PP at high fibre content

The results of an investigation of the mechanical performance of injection moulded long glass fibre reinforced polypropylene with a glass fibre content in the range 0–73 wt% are presented. The composite modulus exhibited a linear dependence on fibre content over the full range of the study. Composite strength and impact resistance exhibited a maximum in performance in the 40–50 wt% reinforcement content range. The residual fibre length and fibre orientation in the samples has also been characterised. These parameters were also found to be fibre concentration dependent. Modelling of the composite strength using the measured fibre length and orientation data did enable a maximum in strength to be predicted. However, the position and absolute level of the predicted maximum did not correlate well with the experimental data. Further analysis indicated that deeper investigation of the dependence of the interfacial shear strength and fibre stress at composite failure on the fibre content are required to fully elucidate these results.