Study of the structural, thermodynamic and electrochemical properties of LaNi3.55Mn0.4Al0.3(Co1−xFex)0.75 (0 ≤ x ≤ 1) compounds used as negative electrode in Ni-MH batteries

This study concerns the influence of iron for cobalt substitution on the structural, thermodynamic and electrochemical properties of the hydrides of poly-substituted LaNi_3.55Mn_0.4Al_0.3(Co_1−xFe_x)_0.75 (0 ≤ x ≤ 1) alloys used as material for negative electrode in Ni-MH batteries. The Fe substitution leads to an increase of the cell parameter, this increase is linear according to the rate of substitution, and a decrease of the equilibrium pressure in agreement with the geometric law. Nevertheless, it is observed that the Fe substitution leads to a deviation from the linear variation between the logarithm of the pressure and the cell volume observed for Co, Mn and Al for Ni substitution. The Fe for Co substitution leads also to a decrease of the solid–gas and electrochemical capacity.     

Influences of the substitution of Fe for Ni on structures and electrochemical performances of the as-cast and quenched La0.7Mg0.3Co0.45Ni2.55−xFex (x = 0–0.4) electrode alloys

In order to improve the cycle stability of the La–Mg–Ni system PuNi₃-type hydrogen storage electrode alloys, Ni in the alloy was partially substituted by Fe. The La_0.7Mg_0.3Co_0.45Ni_2.55−xFe_x (x = 0, 0.1, 0.2, 0.3, 0.4) hydrogen storage alloys were prepared by casting and rapid quenching. The effects of the substitution of Fe for Ni on the structures and electrochemical performances of the as-cast and quenched alloys were investigated in detail. The results of the electrochemical measurement indicate that the substitution of Fe for Ni obviously decreases the discharge capacity, high rate discharge capability (HRD) and discharge potential of the as-cast and quenched alloys, but it significantly improves their cycle stabilities, and its positive impact on the cycle life of as-quenched alloy is much more significant than on that of the as-cast one. The microstructure of the alloys analyzed by XRD, SEM and TEM show that the as-cast and quenched alloys have a multiphase structure which is composed of two major phases (La, Mg)Ni₃ and LaNi₅ as well as a residual phase LaNi₂. The substitution of Fe for Ni helps the formation of a like amorphous structure in the as-quenched alloy. With the increase of Fe content, the grain sizes of the as-quenched alloys significantly reduce, and the lattice constants and cell volumes of the alloys obviously increase.     

Electrochemical characteristics of Mg2−xZrxNi (x = 0–0.6) electrode alloys prepared by mechanical alloying

The electrode alloys Mg_2−xZr_xNi (x = 0, 0.15, 0.3, 0.45 and 0.6) were prepared by mechanical alloying (MA). Mg in the alloy was partially substituted with Zr in order to improve the electrochemical characteristics of the Mg₂Ni-type alloy. The microstructures and the electrochemical characteristics of the experimental alloys were measured systemically. The effects of substituting Mg with Zr and MA technique on the microstructures and electrochemical performances of the alloys were investigated in detail. The results obtained by XRD, SEM and TEM show that the substitution of Zr is favourable for the formation of an amorphous phase. For a fixed milling time, the amorphous phase in the alloy grows with increasing Zr content. The electrochemical measurement indicates that the substitution of Zr can dramatically enhance the discharge capacity with preferable cycle stability, and it markedly improves the discharge voltage characteristic of the alloys. For x ≤ 0.3, the discharge capacity of the alloys monotonically increases with milling time. But for x > 0.3, it has a maximum value with the change of milling time.     

Characterization and hydrogenation of CeNi5−xCrx (x = 0, 1, 2) alloys

The effect of partial substitution of Ni by Cr in CeNi₅ intermetallic compound has been studied by pressure–composition isotherm measurements for different temperatures. The samples were prepared of high purity materials using the standard arc melting technique in argon atmosphere. The structure and the elemental composition of different alloys have been investigated by means of XRD, SEM and EDX techniques. The unit cell volume of the alloy was found to increase with increasing Cr content. In order to calculate the hydrogen storage capacity pressure–composition isotherm has been investigated for CeNi_5−xCr_x (x = 1, 2) alloys in the temperature and pressure ranges of 293 ≤ T ≤ 333 K and 0.5 ≤ P ≤ 35 bar, respectively. The P–C–T isotherm for different alloys clearly shows the presence of three regions ,  + β and β. The enthalpy and entropy for the systems has also been calculated using Van’t Hoff plot. The variation of enthalpy and entropy with hydrogen content has also been studied.     

Effects of cold roll and heat treatments on anomalous thermal behavior in Fe100−xAlx(x = 5–30) alloys

DSC measurements were carried out for various Fe_100−xAl_x(x = 5–30 at%) alloys to clear the effects of cold roll and quenching rate from 1173 K. In the case of cold roll free specimens, an exothermic peak was observed at around 530–560 K in quenched specimens and no peaks in slowly cooled specimens. The peak temperature and its exothermic heat depended on the alloy composition. The maximum exothermic heat was obtained for a 25 at% Al alloy and its value were about 1200 J/mol. The peak in a 5 at% Al alloy was remained as a future work. The exothermic heat was affected by the quenching temperature in alloys above 15 at% Al. The peak temperature was decreased by decreasing the quenching temperature. In a 15 at% Al alloy, the peak became negligibly small by quenching from 1023 K. The activation energies in cold roll free specimens were evaluated from the Kissinger analysis and they were 134, 108, 133 and 110 kJ/mol for 15 at% Al, 20 at% Al, 25 at% Al and 30 at% Al alloys, respectively. On the other hand, cold rolled specimens showed an exothermic peak at around 470 K, independently of the cooling rate. Their exothermic heats and temperatures were comparable order to those of furnace cooled and water quenched specimens. The present results suggested that origin of exothermic peaks of all alloys were same in nature and atomic ordering may be related to the exothermic behavior at relatively low temperatures.     

Influence of tin on the electrochemical and gas phase hydrogen sorption in Mg2−xSnxNi (x = 0, 0.1, 0.3)

Mg_2−xSn_xNi (x = 0, 0.1, 0.3) alloys were synthesized by reactive ball milling under protective Ar atmosphere and liquid n-heptane. The microstructure and the morphology of the powders were determined by X-ray diffraction and scanning electron microscopy. The as-milled alloys consist of Mg₂Ni nanocrystals with an average grain size in the range 3–7 nm, depending on the alloy composition. Sn containing phases were not detected even in the Sn-rich alloy. Obviously, Sn is dissolved in the Mg₂Ni intermetallic compound. Gas phase sorption of hydrogen was not observed in the alloys containing Sn (Mg_2−xSn_xNi; x = 0.1, 0.3). It was suggested that Sn impedes the process of hydrogen molecules decomposition. The as-milled alloys absorbed reversibly hydrogen electrochemically. Mg₂Ni alloy showed the highest discharge capacity of 300 mAh/g. The capacity of Mg_1.9Sn_0.1Ni and Mg_1.7Sn_0.3Ni was about 260 mAh/g. It was found that Sn improved the cycle life of the electrode.     

Electrochemical properties of the MmNi3.55Mn0.4Al0.3Co0.75−xFex (x = 0.55 and 0.75) compounds

The hydrogen storage alloys MmNi_3.55Mn_0.4Al_0.3Co_0.75−xFe_x (x = 0.55 and 0.75) were used as negative electrodes in the Ni-MH accumulators. The chronopotentiommetry and the cyclic voltammetry were applied to characterize the electrochemical properties of these alloys. The obtained results showed that the substitution of the cobalt atoms by iron atoms has a good effect on the life cycle of the electrode. For the MmNi_3.55Mn_0.4Al_0.3Co_0.2Fe_0.55 compound, the discharge capacity reaches its maximum of 210 mAh/g after 12 cycles and then decreases to 190 mAh/g after 30 charge–discharge cycles. However, for the MmNi_3.55Mn_0.4Al_0.3Fe_0.75 compound, the discharge capacity reaches its maximum of 200 mAh/g after 10 cycles and then decreases to 160 mAh/g after 30 cycles.

The diffusion behavior of hydrogen in the negative electrodes made from these alloys was characterized by cyclic voltammetry after few activation cycles. The values of the hydrogen coefficient in MmNi_3.55Mn_0.4Al_0.3Co_0.2Fe_0.55 and MmNi_3.55Mn_0.4Al_0.3Fe_0.75 are, respectively, equal to 2.96 × 10⁻⁹ and 4.98 × 10⁻¹⁰ cm² s⁻¹. However, the values of the charge transfer coefficients are, respectively, equal to 0.33 and 0.3. These results showed that the substitution of cobalt by iron decreases the reversibility and the kinetic of the electrochemical reaction in these alloys.     

Structure and magnetic properties of TbFe10.5−x MnxMo1.5 compounds

The effects of Mn partial substitution for Fe in TbFe_10.5Mo_1.5 on the structure and magnetic properties were investigated. TbFe_10.5−xMn_xMo_1.5 samples (x = 1.5, 2.0, 3.0, 4.0, 5.0) were prepared by means of arc-melting and subsequent vacuum annealing. The structure and magnetic properties of TbFe_10.5−xMn_xMo_1.5 compounds were investigated by X-ray powder diffraction and magnetic properties measurements. The following conclusions were obtained: all the TbFe_10.5−xMn_xMo_1.5 compounds studied crystallize in the ThMn₁₂-type structure; the unit-cell volume increases monotonically with increasing Mn concentration; a compensation temperature was observed in the magnetization-temperature curve of TbFe_7.5Mn₃Mo_1.5 compounds. With increasing Mn concentration, the saturation magnetization at 4.4 K decreases to zero, and then increases again, the magnetic moments of the transition-metal sublattice of TbFe_10.5−xMn_xMo_1.5 compounds decrease monotonically.     

Structures and superparamagnetic properties of overaged Fe–Al–Mn–C alloys

Microstructures and superparamagnetic properties in aged-hardened Fe–9%Al–30%Mn– (x)C,Si alloys, resulting from overaging at a temperature of 823 K for 48 h to 313 days, have been investigated by transmission electron microscopy (TEM), X-ray diffraction patterns, and vibrating sample magnetometry (VSM). The results reveal that the precipitate κ-phase [(Fe,Mn)₃AlC] decomposition in this alloy, overaged at 823 K for one week, resulted from two separate mechanisms: (1) wetting of the antiphase boundary segment (APBs) of D0₃ [(Fe/Mn)₃Al] domains by the B2 [(Fe/Mn)Al] phase; and (2) precipitation of the B2 [(Fe/Mn)Al] phase within the domain. A superparamagnetic behaviour was discovered when the alloy was overaged at 823 K for ≈120–313 days. The super-soft magnetic property was mainly attributable to the ferromagnetic spinel-ordered (B2 [(Fe/Mn)Al]+D0₃ [(Fe/Mn)₃Al]) phases and ordered B2 with monoclinic ′Mn structures.     

On the crystal structure of new series of compounds, RPt2+xSb2−y (x = 0.125, y = 0.25; R = La, Ce, Pr)

A new compound CePt_2+xSb_2−y (x = 0.125, y = 0.25) was synthesized by arc-melting of the elements. The chemical and structural characterizations were carried out at room temperature on as-cast samples using X-ray diffractometry, metallographic analysis and EDS-microanalysis. According to the results of X-ray single crystal diffraction this antimonide crystallizes in I4cm space group (no. 108), Z = 32, ρ = 12.19 Mg/m³, μ = 89.05 mm⁻¹ (a = 12.5386(3) Å, c = 21.4692(6) Å (crystal I) and a = 12.5455(2) Å, c = 21.4791(5) Å (crystal II)). The structure and composition were confirmed by powder X-ray diffraction (a = 12.4901(2) Å, c = 21.3620(4) Å) and EDS-microanalysis respectively. Isotypic compounds were observed with La and Pr from X-ray powder diffraction of as-cast alloys at room temperature (a = 12.6266(4) Å, c = 21.4589(6) Å for LaPt_2+xSb_2−y and a = 12.5184(5) Å, c = 21.4178(7) Å for PrPt_2+xSb_2−y). The CePt_2+xSb_2−y structure is derived from CaBe₂Ge₂ (a = 2a₀ − 2b₀, b = 2a₀ + 2b₀, c = 2c₀) and comprises a new atomic arrangement with both vacancy on 4(b) pyramidal site and substitution of antimony atoms (X) by platinum (B) in the B–XX–B layers (referring to the subcell structure) forming two B––1/2B1/2XX–3/4B and two X–BB–X layers per cell. The structure of CePt_2+xSb_2−y is compared with those reported before for URh_1.6As_1.9 and CeNi_1.91As_1.94.     

Corrosion resistance of (Nd,Dy)16(Fe,Co)76−xTixB8 mechanically alloyed magnets

Nanocrystalline (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ magnets were prepared by mechanical alloying and respective heat treatment at 973–1073 K/30–60 min. An addition of 0.5 at.% of Ti results in increase of coercivity from 796 to 1115 kA/m. Partial substitution of Nd by Dy results in an additional increase of coercivity up to 1234 kA/m. The highest corrosion resistance have magnets with 0.5–0.75 at.% of Ti. Beside the Ti, the Co and Dy content significantly improve the corrosion resistance, too. It was found, that for Ti content smaller than x ≤ 1, the (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ powders are single phase. For higher Ti contents (x > 1) the mechanically alloyed powders heat treated at 973 K are no more single phase, and the coercivity as well as corrosion resistance decreases due to the presence of an amorphous phase and -Fe. A heat treatment at a higher temperature (1073 K/30 min) or at 973 K for longer time (1 h) results in the full recrystallisation of the powders. The obtained homogenized structure results in higher corrosion resistance.     

Effects of substituting Ni with M (M=Cu, Al and Mn) on microstructures and electrochemical characteristics of La-Mg-Ni system (PuNi3-type) electrode alloys

In order to improve the electrochemical cycle stability of La-Mg-Ni system (PuNi3-type) hydrogen storage alloy, Ni in the alloys was partially substituted by M (M=Cu, Al, Mn). A new La-Mg-Ni system electrode alloys La0.7Mg0.3Ni2.55-xCo0.45Mx (M=Cu, Al, Mn;x =0,0.1) were prepared by casting and rapid quenching. The effects of element substitution and rapid quenching on the microstructures and electrochemical performances of the alloys were investigated. The results by XRD, SEM and TEM show that the alloys havea multiphase structure, including the (La, Mg)Ni3 phase, the LaNi5 phase and the LaNi2 phase. The rapid quenching and element substitution have an imperceptible influence on the phase compositions of the alloys, but both change the phase abundance of the alloys. The rapid quenching significantly improves the composition homogeneity of the alloys and markedly decreases the grain size of the alloys. The Cu substitution promotes the formation of an amorphous phase in the as-quenched alloy, and a reversal result by the Al substitution. The electrochemical measurement indicates that the element substitution decreases the discharge capacity of the alloys, whereas it obviously improves the cycle stability of the alloys. The positive influence of element substitution on the cycle life of the alloys is in sequence Al＞Cu＞Mn, and negative influence on the discharge capacity is in sequence Al＞Mn＞Cu. The rapid quenching significantly enhances the cycle stability of the alloys, but it leads to a different extent decrease of thedischarge capacity of the alloys.     

Temporal evolution of the nanostructure of Al(Sc,Zr) alloys: Part II-coarsening of Al3(Sc1−xZrx) precipitates

The coarsening behavior of four Al(Sc,Zr) alloys containing small volume fractions (<0.01) of Al₃(Sc_1−xZr_x) (L1₂) precipitates was investigated employing conventional transmission electron microscopy (CTEM) and high-resolution electron microscopy (HREM). The activation energies for diffusion-limited coarsening were obtained employing the Umantsev–Olson–Kuehmann–Voorhees (UOKV) model for multi-component alloys. The addition of Zr is shown to retard significantly the coarsening rate and stabilize precipitate morphologies. HREM of Al(Sc,Zr) alloys aged at 300 °C reveals Al₃(Sc_1−xZr_x) precipitates with sharp facets parallel to {1 0 0} and {1 1 0} planes. Coarsening of Al-0.07 Sc-0.019 Zr at.%, Al-0.06 Sc-0.005 Zr at.% and Al-0.09 Sc-0.047 Zr at.% alloys is shown to be controlled by volume diffusion of Zr atoms, while coarsening of Al-0.14 Sc-0.012 Zr at.% is controlled by volume diffusion of Sc atoms.     

Fe替代Ni对铸态及快淬态La0.7Mg0.3Co0.45Ni2.55-xFex (x = 0-0.4)电极合金循环稳定性的影响

用铸造及快淬工艺制备了La0.7Mg0.3Co0.45Ni2.55-xFex(x=0,0.2,0.3,0.4)电极合金,研究了Fe替代Ni对合金循环稳定性及微观结构的影响。结果表明,Fe替代Ni显著地改善合金的循环稳定性,且Fe替代Ni对快淬态合金的循环稳定性具有更加显著的作用。试验合金具有多相结构,包括2个主相(La,Mg)Ni3和LaNi5以及1个残余相LaNi2。Fe替代Ni促进快淬态合金形成类非晶结构,随Fe含量的增加,快淬态合金的晶粒显著细化,合金的晶格常数及晶胞体积显著增大。     

Investigation on the structures and electrochemical performances of La0.75−xZrxMg0.25Ni3.2Co0.2Al0.1 (x = 0–0.2) electrode alloys prepared by melt spinning

In order to improve the electrochemical cycle stability of the La–Mg–Ni system A₂B₇-type electrode alloys, La in the alloy was partially substituted by Zr and the melt-spinning technology was used for preparing La_0.75−xZr_xMg_0.25Ni_3.2Co_0.2Al_0.1 (x = 0, 0.05, 0.1, 0.15, 0.2) electrode alloys. The microstructures and electrochemical performances of the as-cast and quenched alloys were investigated in detail. The results obtained by XRD, SEM and TEM showed that the as-cast and quenched alloys have a multiphase structure which is composed of two main phases (La, Mg)Ni₃ and LaNi₅ as well as a residual phase LaNi₂. The substitution of Zr for La leads to an obvious increase of the LaNi₅ phase in the alloys, and it also helps the formation of a like amorphous structure in the as-quenched alloy. The results of the electrochemical measurement indicated that the substitution of Zr for La obviously decreased the discharge capacity of the as-cast and quenched alloys, but it significantly improved their cycle stability. The discharge capacity of the alloys (x ≤ 0.1) first increased and then decreased with the variety of the quenching rate. The cycle stability of the alloys monotonously rose with increasing quenching rate.     

Preparation and structures of the La1−xKxCo1−xNbxO3 (x = 0–l) system

The La_1−xK_xCo_1−xNb_xO₃ system was performed by conventional solid state reaction technique using metal oxides. By DSC analysis, the activation energy of crystallization of the powders with x = 0.3 is 388.4 kJ/mol. The crystal structure of the compound reveals a transition from rhombohedral to cubic, and then to orthorhombic structure as the amount of the potassium niobate (KNbO₃) increases. It is found that the structure of the samples with x < 0.3 is similar to that of lanthanum cobaltate (LaCoO₃), while at the compositions with 0.7 ≥ x ≥ 0.3, the structure transforms to cubic. Finally, with x ≥ 0.7, the structures were similar to that of KNbO₃. According to the results of selected-area-diffraction (SAD) patterns and X-ray diffraction (XRD) identifications, the lattice parameters were calculated. The direction of superlattice structure along [2 1 0] was found for x = 0.5 as identified from SAD patterns. The dielectric constants were measured with cubic structure. Dielectric constant (K) decreases with increasing x.     

Effect of AI content on the phase structure and the hydrogenation characteristic of La（Mg1-xAlx） alloys

La（Mg1-xAlx） （x=0.2, 0.4, 0.6, 0.8） alloys have been prepared using induction melting followed by annealing. It is found that partial substitution of Mg by Al does not lead to a change in crystal structure, and the alloys have a single LaMg phase when x 〈 0.4. The lattice parameter of the LaMg phase decreases obviously after the partial substitution of Mg by Al. However, further substitution of Mg by Al leads to the coexistence of multiple phases when x ≥ 0.6. The alloys consist of the LaMg, LaAl, LaAl2, and La5Al4 phases. The LaMg phase decreases, whereas the La5Al4 phase increases with the increase in x. The Al-substituted La（Mgo.6Al0.4） alloy can be hydrogenated into the tetragonal LaH3, cubic LaH3, MgH2, and LaPd under 5 MPa at 473 K for 5 d.     

X-ray diffraction and Mössbauer study of (Fe1−xNix)4N (0.2 ≤ x ≤ 0.6) films

Single phase (Fe_1−xNi_x)₄N compounds (0.2 ≤ x ≤ 0.6) have been synthesized by reactive evaporation and investigated by X-ray diffraction and Mössbauer spectrometry. The lattice parameters of the nitrides decrease from 3.796 to 3.774 Å with increasing Ni concentration. The fitting results of Mössbauer spectra indicate that the average hyperfine field have the same changing tendency with lattice parameter and the nickel atoms have a tendency to be located at the corner site.     

Synthesis and characterization of LiGaxMn2−xO4 (0 ≤ x ≤ 0.05) by triethanolamine-assisted sol–gel method

Spinel LiGa_xMn_2−xO₄ (0 ≤ x ≤ 0.05) cathode materials with phase-pure particles and nano-sized distribution were synthesized by sol–gel method using triethanolamine as the chelating agent. The effects of heat treatment on the physicochemical properties of the spinel LiGa_xMn_2−xO₄ powders were examined with thermogravimetric and differential thermal analysis (TG/DTA), powder X-ray diffraction (XRD) and scanning electron micrograph (SEM). The LiGa_xMn_2−xO₄ (0 ≤ x ≤ 0.05) electrodes were characterized electrochemically by charge/discharge experiments under a current rate of 0.5C at 55 °C. Although the Ga-doped spinel electrode showed smaller initial discharge capacity, it exhibited better cycling performance than the undoped-LiMn₂O₄ electrode. The dQ/dV versus potential plots at 55 °C revealed that the improvement in cycling performance of the Ga-doped spinel electrode is attributed to stabilization of the spinel structure by the presence of gallium ion.     

Magnetocrystalline anisotropy of Nd3(Fe1−xCox)27.7Ti1.3Ny compounds

The effect of Co substitution for Fe in Nd₃(Fe_1−xCo_x)_27.7Ti_1.3N_y (0 ≤ x ≤ 0.4) compounds on the magnetocrystalline anisotropy has been investigated. The anisotropy constants K's and the anisotropy field H_A have been deduced from the magnetization curves measured on magnetically aligned powder (4–7 μm) samples. The obtained results show that at RT the anisotropy is uniaxial and H_A (about 10 T) does not change substantially upon the substitution. At 5 K the results for K's give evidence for the presence of easy-cone-type anisotropy. The cone angle as well as the anisotropy field decrease upon the substitution from 21.6° to 11.8° and from 22.8 to 18.6 T, respectively.