Low-loss microwave dielectrics using rock salt oxide Li2MgTiO4

Rock-salt-structured Li₂MgTiO₄ ceramic was prepared by the conventional mixed oxide route and its microwave dielectric properties were investigated. The microstructures of the ceramics were characterized by SEM. The dielectric properties of the ceramics exhibited a significant dependence on the sintering condition and crystal structure. A new microwave dielectric material, Li₂MgTiO₄ sintered at 1360 °C has a dielectric constant (?_r) of ∼17.25, a Q × f of ∼97,300 GHz (where f = 9.86 GHz, is the resonant frequency) and a τ_f of ∼-27.2 ppm/°C. The microwave dielectric properties of the ceramic are reported for the first time.     

Effect of dwell time during sintering on piezoelectric properties of (Ba0.85Ca0.15)(Ti0.90Zr0.10)O3 lead-free ceramics

In this letter, the effect of dwell time (1-6 h) during sintering on the piezoelectric properties is investigated for the (Ba_0.85Ca_0.15)(Ti_0.90Zr_0.10)O₃ ceramics. All ceramics sintered at different dwell time are of a pure phase, and its structure distortion is induced by too long dwell time. Their dielectric constant and remanent polarization increases and the coercive field decreases with increasing dwell time. An enhanced piezoelectric behavior (d₃₃ ∼ 492 pC/N and k_p ∼ 51.5%) is demonstrated for the BCTZ ceramic with an optimum dwell time of 5 h, owing to the structure distortion together with a dense microstructure and a larger grain size.     

Effect of CaTiO3 addition on microwave dielectric properties of Mg2(Ti0.95Sn0.05)O4 ceramics

The microwave dielectric properties of CaTiO₃-added Mg₂(Ti_0.95Sn_0.05)O₄ ceramics prepared by the mixed oxide route have been investigated. The combination of spinel-structured Mg₂(Ti_0.95Sn_0.05)O₄ and perovskite-structured CaTiO₃ forms a two-phase system (1 − x)Mg₂(Ti_0.95Sn_0.05)O₄-xCaTiO₃, which was confirmed by the XRD patterns and the EDX analysis and it also leads to a zero τ_f. The microwave dielectric properties of the ceramics can be effectively controlled by varying the x value. For practical applications, a new microwave dielectric material 0.91Mg₂(Ti_0.95Sn_0.05)O₄-0.09CaTiO₃ is suggested and it possesses a good combination of dielectric properties with an ?_r of ∼18.01, a Q × f of ∼92,000 GHz, and a τ_f of ∼0 ppm/°C, which makes it is a very promising candidate material for high frequency applications.     

Microwave properties of Ba(Zn1/3Ta2/3)O3 dielectric resonators

Ba(Zn_1/3Ta_2/3)O₃ (BZT) dielectric resonators were prepared by solid-state reaction. The starting materials were BaCO₃, ZnO, and Ta₂O₅ powders with high purity. The double calcined BZT pellets were sintered in air at temperatures of 1575, 1600, 1625, and 1650 °C for 4 h. The X-ray diffraction data allowed the study of the unit cell distortion degree and the presence of the secondary phases. A long-range order with a 2:1 ratio of Ta and Zn cations on the octahedral positions of the perovskite structure was observed with the increase of the sintering temperature. The dielectric constant of BZT resonators measured around 6 GHz was between 26 and 28. High values of Q × f product (120 THz) were obtained for BZT resonators sintered at 1650 °C/4 h. The temperature coefficient of the resonance frequency exhibits positive values less than 6 ppm/°C. The achieved dielectric parameters recommend BZT dielectric resonators for microwave and millimeter wave applications.     

Ferroelectric relaxor behavior and dielectric spectroscopic study of 0.99(Bi0.5Na0.5TiO3)-0.01(SrNb2O6) solid solution

0.99(Bi_0.5Na_0.5TiO₃)-0.01(SrNb₂O₆) was prepared by simple solid state reaction route. Material stabilized in rhombohedral perovskite phase with lattice constants a = 3.9060 Å, α = 89.86° and a_h = 5.4852 Å, c_h = 6.7335 Å for hexagonal unit cells. Density of material was found 5.52 g_m/cm³ (92.9% of theoretical one) in the sample sintered at 950 °C. The temperature dependent dielectric constant exhibits a broad peak at 538 K (?_m = 2270) at 1 kHz that shows frequency dependent shifts toward higher temperature - typical relaxor behavior. Modified Curie-Weiss law was used to fit the dielectric data that exhibits almost complete diffuse phase transition characteristics. The dielectric relaxation obeys the Vogel-Fulcher relationship with the freezing temperature 412.4 K. Significant dielectric dispersion is observed in low frequency regime in both components of dielectric response and a small dielectric relaxation peak is observed. Cole-Cole plots indicate polydispersive nature of the dielectric relaxation; the relaxation distribution increases with increase in temperature.     

Dielectric and piezoelectric properties of Sb doped (NaBi)0.38(LiCe)0.05[]0.14Bi2Nb2O9 ceramics

Sb⁵⁺-doped (NaBi)_0.38(LiCe)_0.05[]_0.14Bi₂Nb₂O₉ (represented as NBNLCS-x, where [] represents A-site vacancies) ceramics were prepared by the conventional solid-state route. The ceramics well sintered to approach ∼98.5% theoretical density and the tetragonality of crystal structure increased with Sb⁵⁺ additions. However, the Curie temperature (T_C) and the piezoelectric coefficient (d₃₃) of Sb⁵⁺-modified ceramics gradually decreased. The 3 mol% Sb⁵⁺-doped samples exhibited optimum properties with a d₃₃ value of ∼22 pC/N planar electromechanical coupling factor (k_p) of ∼11.2% and relatively high T_C of ∼765 °C. These results indicate that NBNLCS-x material is a promising candidate for high-temperature piezoelectric applications.     

Dielectric and magnetic behavior of BaCd2−xSrxFe16O27 W-type hexagonal ferrites

We have prepared BaCd_2−xSr_xFe₁₆O₂₇ (x = 0, 0.5, 1, 1.5 and 2.0) W-type hexagonal ferrites by standard ceramic method. In this work, the structural, dielectric and magnetic properties have been studied of the prepared samples. The XRD analysis of the samples reveals single phase behavior sintered at 1400 °C for 6 h. The saturation magnetization (M_s) shows increasing behavior with the increasing concentration of Sr²⁺. While the coercivity (H_c) decreases rapidly up to 409 G for x = 1.5 and then increases for (x > 1.5) due to the preference of Cd²⁺ for tetrahedral sites and the number of spin-down magnetic ions. The real and imaginary parts of the dielectric constant (?′,?″) and dielectric loss tangent (tan δ) are determined in the frequency range 0.1-10⁷ Hz. It is observed that both the real and imaginary parts of the dielectric constant and tan δ decrease with the increasing concentration of Sr²⁺, which is due to the contribution of Cd²⁺ ions in addition to Fe³⁺ and Fe²⁺ ions to interfacial polarization.     

Synthesis and functional properties of the Ni1−xMnxFe2O4 ferrites

Nanocrystalline Ni_1−xMn_xFe₂O₄ (x = 0; 0.17; 0.34; 0.5) ferrite powders were successfully synthesized using the sol-gel combustion method, by using nitrates as cations source and citric acid (C₆H₈O₇) as combustion/chelating agent. The reaction advancement was observed by means of IR absorption spectroscopy, by monitoring two characteristic bands for the spinel compounds at about 600 cm⁻¹ and 400 cm⁻¹, respectively. The as-synthesized powders were characterized by IR spectroscopy, X-ray diffraction (XRD) and scanning electronic microscopy (SEM). The magnetic study shows that the saturation magnetization decreases with increasing the Mn addition, as result of the particle size reduction. The dielectric properties were measured as a function of frequency in the range of 10 Hz to 1 MHz. The real part of permittivity has values of ∼88 at 1 kHz and ∼7 at 1 Hz for x = 0. An increasing dielectric permittivity with increasing the amount of Mn is observed. For all the investigated compositions, both the real and imaginary parts of permittivity decrease with frequency.     

Piezoelectric and dielectric properties of Dy2O3-doped (Bi0.5Na0.5)0.94Ba0.06TiO3 lead-free ceramics

(Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ + x wt% Dy₂O₃ with x = 0-0.3 ceramics were synthesized by conventional solid-state processes. The effects of Dy₂O₃ on the microstructure, the piezoelectric and dielectric properties were investigated. X-ray diffraction pattern confirmed that the coexistence of tetragonal and rhombohedral phases in the (Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ composition was not changed by adding 0.05-0.3 wt% Dy₂O₃. SEM images indicate that all the ceramics have pore-free microstructures with high density, and that doping of Dy₂O₃ inhibits the grain growth of the ceramics. The addition of Dy₂O₃ shows the double effects on decreasing the piezoelectric and dielectric properties for 0 < x < 0.15 when Dy³⁺ ions substitute B-site Ti⁴⁺ ions, and increasing the properties for 0.15 < x < 0.3 when Dy³⁺ ions enters into A-site of the perovskite structure. The optimum electric properties of piezoelectric constant d₃₃ = 170 pC/N and the dielectric constant ?_r = 1900 (at a frequency of 1 kHz) are obtained at x = 0.3.     

Phase evolution and microwave dielectric properties of TiO2-modified (Mg0.95Co0.05)2TiO4 ceramics

Phase evolution and microwave dielectric properties of (1 − x)(Mg_0.95Co_0.05)₂TiO₄-xTiO₂ (x = 0-1) ceramics prepared by the conventional mixed oxide route have been investigated. Increasing the TiO₂ content would lead to a main phase transformation from (Mg_0.95Co_0.05)₂TiO₄ to (Mg_0.95Co_0.05)TiO₃, (Mg_0.95Co_0.05)Ti₂O₅ and then TiO₂. Not only did the TiO₂ addition compensate the τ_f, it also lowered the sintering temperature of specimen. A huge drop of Q × f occurs at a 40-60 mol% TiO₂ addition was attributed to the formation of (Mg_0.95Co_0.05)Ti₂O₅ phase. Specimen with x = 0.78 can possess an excellent combination of microwave dielectric properties: ?_r ∼ 24.77, Q × f ∼ 38,500 GHz and τ_f ∼ −1.3 ppm/°C.     

Synthesis of (Bi0.5Na0.5)TiO3 (BNT) and Pr doped BNT using the soft combustion technique and its properties

In this work, bismuth sodium titanate (Bi_0.5Na_0.5)TiO₃ (BNT) and praseodymium (Pr)-doped BNT were successfully produced using the soft combustion technique. The effects of Pr doping on stoichiometry, microstructure, density and dielectric properties were studied. Pure Pr-doped BNT was obtained in all samples containing 5, 10 and 20 mol% Pr after calcination at 800 °C for 3 h. The produced powders were then pressed into pellets and sintered at 1100 °C for 3 h. The very similar ionic radii of Pr³⁺ with Bi³⁺ and Na⁺ made it possible to substitute both Bi and Na. The crystallite size and grain size decreased with increasing Pr amount because Pr acted as grain growth inhibitor, both for calcined powders and for sintered pellets. Maximum density was obtained in 5 mol% Pr-doped BNT, beyond which density decreased. The maximum dielectric constant of 756 was obtained in 5 mol% Pr-doped BNT and decreased at higher levels of Pr doping. Pr doped into BNT also caused a decrease in dielectric loss.     

Sinterability and dielectric properties of Ba0.55Sr0.4Ca0.05TiO3-CaTiSiO5-Mg2TiO4 composite ceramics

The composite ceramics of Ba_0.55Sr_0.4Ca_0.05TiO₃-CaTiSiO₅-Mg₂TiO₄ (BSCT-CTS-MT) were prepared by the conventional solid-state route. The sintering performance, phase structures, morphologies, and dielectric properties of the composite ceramics were investigated. The BSCT-CTS-MT ceramics were sintered at 1100 °C and possessed dense microstructure. The dielectric constant was tailored from 1196 to 141 as the amount of Mg₂TiO₄ increased from 0 to 50 wt%. The dielectric constant and dielectric loss of 40 wt% Ba_0.55Sr_0.4Ca_0.05TiO₃-10 wt% CaTiSiO₅-50 wt% Mg₂TiO₄ was 141 and 0.0020, respectively, and the tunability was 8.64% under a DC electric field of 8.0 kV/cm. The Curie peaks were broadened and depressed after the addition of CaTiSiO₅. The optimistic dielectric properties made it a promising candidate for the application of tunable capacitors and phase shifters.     

Dielectric relaxation behaviors of pure and Pr6O11-doped CaCu3Ti4O12 ceramics in high temperature range

Pure and Pr₆O₁₁-doped CaCu₃Ti₄O₁₂ (CCTO) ceramics were prepared by conventional solid-state reaction method. The compositions and structures were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The influences of Pr-ion concentration on dielectric properties of CCTO were measured in the ranges of 60 Hz-3 MHz and 290-490 K. The third phase of Ca₂CuO₃ was observed from the XRD of CCTO ceramics. From SEM, the grain size was decreased obviously with high valence Pr-ion (mixing valence of Pr³⁺ and Pr⁴⁺) substituting Ca²⁺. The room temperature dielectric constant of Pr-doped CCTO ceramics, sintered at 1323 K, was an order of magnitude lower than the pure CCTO ceramics due to the grain size decreasing and Schottky potential increasing. The dielectric spectra of Pr-doped CCTO were flatter than that of pure CCTO. The loss tangent of Pr-doped CCTO ceramics was less than 0.20 in 2 × 10²-10⁵ Hz region below 440 K. The complex impedance spectra of pure and Pr-doped CCTOs were fitted by ZView. From low to high frequency, three semicircles were observed corresponding to three different conducting regions: electrode interface, grain boundary and grain. By fitting the resistors R and capacitors C, the activation energies of grain boundary and electrode contact were calculated. All doped CCTOs showed higher activation energies of grain boundary and electrode than those of pure CCTO ceramics, which were concordant with the decreasing of dielectric constant after Pr₆O₁₁ doping.     

Microwave dielectric properties and its compatibility with silver electrode of Li2MgTi3O8 ceramics

The effects of BaCu(B₂O₅) (BCB) additions on the sintering temperature and microwave dielectric properties of Li₂MgTi₃O₈ ceramic have been investigated. The pure Li₂MgTi₃O₈ ceramic shows a relative high sintering temperature (∼1000 °C) and good microwave dielectric properties as Q × f of 40,000 GHz, ?_r of 27.2, τ_f of 2.6 ppm/°C. It was found that the addition of a small amount of BCB can effectively lower the sintering temperature of Li₂MgTi₃O₈ ceramics from 1025 to 900 °C and induce no obvious degradation of the microwave dielectric properties. Typically, the 0.5 wt% BCB added Li₂MgTi₃O₈ ceramic sintered at 900 °C for 2 h exhibited good microwave dielectric properties of Q × f = 36,200 GHz (f = 7.31 GHz), ?_r = 26 and τ_f = −2 ppm/°C. Compatibility with Ag electrode indicates this material can be applied to low temperature-cofired ceramics (LTCC) devices.     

Ba(Ti1 − xSnx)O3 (x = 0.13) nanomaterials produced by low-temperature aqueous synthesis

BaTi_0.87Sn_0.13O₃ (BTS₁₃) nanopowder was prepared by low-temperature aqueous synthesis (LTAS) method. The evolution of the structure and microstructure of the precursor precipitate, heated at temperatures up to 1000 °C was studied by TGA, FT-IR, SEM and XRD techniques. The dried precipitate showed a microstructure consisting of nano-sized grains (∼40 nm) with great tendency to agglomeration. BaTi_0.87Sn_0.13O₃ single phase was obtained at 800 °C. The ceramics prepared from as-obtained BTS₁₃ powders (60-70 nm) show good dielectric and ferroelectric characteristics. The dielectric constant was about 4800 and the dielectric loss (tan δ) was 0.229 at 1 kHz and at the Curie temperature (31 °C). The remanent polarization (P_r) and the coercive field (E_C) of Ba_0.97Ho_0.03TiO₃ ceramics, at 1 kHz, were P_r = 13 μC/cm² and E_C = 0.89 kV/cm. The ferroelectric parameters E_C and P_r decrease with increasing frequency in the domain 100 Hz to 10 kHz.     

Enhanced magnetoelectric properties in Bi0.95Ho0.05FeO3 polycrystalline ceramics

Polycrystalline samples of Ho doped BiFeO₃ were prepared by solid state reaction method and effect of partial substitution of Ho on dielectric, magnetic and ferroelectric properties was studied. High temperature dielectric results show two dielectric anomalies both in ? and tan δ, out of which, anomaly at higher temperature (∼400 °C) could be ascribed to antiferromagnetic Néel temperature which, is a signature of magnetoelectric coupling. The magnetic moment is greatly improved and the maximum magnetization was found to be 0.736 emu/g. Saturated ferroelectric hysteresis loops were observed for Bi_0.95Ho_0.05FeO₃ with remnant polarization (P_r) = 1.59 μC/cm², maximum polarization (P_max) = 2.56 μC/cm² and coercivity (E_c) = 5.45 kV/cm. We have conducted comprehensive magnetoelectric and magnetodielectric properties at room temperature. Magnetic field induced ferroelectric hysteresis loop observed in Bi_0.95Ho_0.05FeO₃ is of prime importance.     

Dielectric properties and crystal structure of La(Mg1/2Ti1/2)O3 ceramics with Mg substituted by Co

Solid solutions of (1 − x)La(Co_1/2Ti_1/2)O₃-xLa(Mg_1/2Ti_1/2)O₃ were used to prepare La(Mg_1−xCo_x)_1/2Ti_1/2O₃ using solid-state synthesis. X-ray diffraction patterns of the sintered samples revealed single phase formation. A maximum density of 6.01 g/cm³ was obtained for La(Mg_1−xCo_x)_1/2Ti_1/2O₃ (x = 1) ceramics sintered at 1375 °C for 4 h. The maximum values of the dielectric constant (?_r = 29.13) and the quality factor (Q × f = 80,000 GHz) were obtained for La(Mg_1−xCo_x)_1/2Ti_1/2O₃ with 1 wt% ZnO additive sintered at 1375 °C for 4 h. The temperature coefficient of resonant frequency τ_f was −59 ppm/°C for x = 0.3.     

Elucidating the dielectric properties of Mg2SnO4 ceramics at microwave frequency

This study investigated the potential applications of microwave dielectric properties of Mg₂SnO₄ ceramics in mobile communication. Mg₂SnO₄ ceramics were prepared using a conventional solid-state method. The X-ray diffraction patterns of the Mg₂SnO₄ ceramics revealed no significant variation of phase with sintering temperature. A maximum density of 4.62 g/cm³, a dielectric constant (?_r) of 8.41, a quality factor (Q × f) of 55,100 GHz, and a temperature coefficient of resonant frequency (τ_f) of −62 ppm/ °C were obtained when Mg₂SnO₄ ceramics were sintered at 1550 °C for 4 h.     

Low temperature sintering and microwave dielectric properties of (Mg0.7Zn0.3)0.95Co0.05TiO3 ceramics with BaCu(B2O5) additions

The effects of BaCu(B₂O₅) additives on the sintering temperature and microwave dielectric properties of (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics were investigated. The (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics were not able to be sintered below 1000 °C. However, when BaCu(B₂O₅) were added, they were sintered below 1000 °C and had the good microwave dielectric properties. It was suggested that a liquid phase with the composition of BaCu(B₂O₅) was formed during the sintering and assisted the densification of the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics at low temperature. BaCu(B₂O₅) powders were produced and used to reduce the sintering temperature of the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics. Good microwave dielectric properties of Q × f = 35,000 GHz, ?_r = 18.5.0 and τ_f = −51 ppm/°C were obtained for the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics containing 7 wt.% mol% BaCu(B₂O₅) sintered at 950 °C for 4 h.     

Preparation and electrical properties of Bi0.5Na0.5TiO3-BaTiO3-KNbO3 lead-free piezoelectric ceramics

Lead-free (1 − x)Bi_0.47Na_0.47Ba_0.06TiO₃-xKNbO₃ (BNBT-xKN, x = 0-0.08) ceramics were prepared by ordinary ceramic sintering technique. The piezoelectric, dielectric and ferroelectric properties of the ceramics are investigated and discussed. The results of X-ray diffraction (XRD) indicate that KNbO₃ (KN) has diffused into Bi_0.47Na_0.47Ba_0.06TiO₃ (BNBT) lattices to form a solid solution with a pure perovskite structure. Moderate additive of KN (x ≤ 0.02) in BNBT-xKN ceramics enhance their piezoelectric and ferroelectric properties. Three dielectric anomaly peaks are observed in BNBT-0.00KN, BNBT-0.01KN and BNBT-0.02KN ceramics. With the increment of KN in BNBT-xKN ceramics, the dielectric anomaly peaks shift to lower temperature. BNBT-0.01KN ceramic exhibits excellent piezoelectric properties and strong ferroelectricity: piezoelectric coefficient, d₃₃ = 195 pC/N; electromechanical coupling factor, k_t = 58.9 and k_p = 29.3%; mechanical quality factor, Q_m = 113; remnant polarization, P_r = 41.8 μC/cm²; coercive field, E_c = 19.5 kV/cm.