High yield strength bulk Ti based bimodal ultrafine eutectic composites with enhanced plasticity

Ti-based bulk metallic glass (BMGs) and their bimodal composites are linked with the pronounced strain hardening after yielding but with much low value of strength. Therefore, developing Ti-based alloys with high yield strength and high plasticity is the current challenge. Here, we report the synthesis of ultra-fine grained bulk (UFG) (Ti_0.705Fe_0.295)_100−xGa_x (0 ⩽ x ⩽ 2) bimodal eutectic composites with not only high strength and larger plasticity but also with high yield strength which is one of the important mechanical property for structural application. Reasonably high strength, high yield strength, strain to failure ratio, and enhanced plasticity of ∼7 ± 0.8% was observed in (Ti_70.5Fe_29.5)₉₈Ga₂ composite which is superior than Ti-based BMGs and bimodal composites. Modification of degree of eutectic structure refinement and volume fraction of constituent phases with the addition of Ga are the crucial factors in enhancing the mechanical properties of Ti–Fi–(Ga) composites.     

Influence of SrTiO3 modification on dielectric properties of Mg(Zr0.05Ti0.95)O3 ceramics at microwave frequency

The microwave dielectric properties and microstructures were investigated in the (1?x)Mg(Zr_0.05Ti_0.95)O₃–xSrTiO₃ (hereafter referred to as (1?x)MZT–xST) system. The compounds were prepared via the conventional solid-state reaction. Compositions in the (1?x)Mg(Zr_0.05Ti_0.95)O₃–xSrTiO₃ system were designed to compensate the negative temperature coefficient of the resonant frequency of Mg(Zr_0.05Ti_0.95)O₃. The values displayed nonmonotonic mixture-like behavior, because the TiO₂ phase was formed in the MZT composite ceramics with increasing x. A close zero τ_f of 0.2 ppm/°C could be achieved at 0.96MZT–0.04ST with ?_r = 20.8 and Q × f = 257,000 GHz.     

Structural and chemical characterization of precipitates in Al-2024/TiC composites

Structural characterizations based on transmission electron microscopy observations were carried out on as-fabricated and heat-treated Al-2024/TiC composites. These composites types reinforced with TiC particles were produced with a pressureless melt infiltration route at 1200 °C for 2 h under argon atmosphere. The composites were heat-treated at 530 °C during 150 min, cold-water quenched and subsequently artificial and natural aged at 190 °C for 12 h in an argon environment and at room temperature for 96 h, respectively. Different precipitate types were obtained and they were identified as CuAl₂, Al₃Ti, Ti₃AlC and Ti₃Al. Most of the precipitates were found to be uniformly distributed in the matrix and some regions show precipitates which have a cubic morphology (Ti₃Cu). High-resolution electron microscopy images were partially used for the characterization of the precipitates in these composites.     

Effect of V content on microstructure and mechanical property of a TiVCuNiAl composite fabricated by spark plasma sintering

Ultrafine-grained (Ti₄₀Cu_22.9Ni_19.4Al_17.7)_x(Ti₈₀V₂₀)_1−x (x = 0.35 and 0.55) composites were fabricated by spark plasma sintering and crystallization of amorphous phase. Outstanding difference in microstructure and mechanical property is found for the two composites. Microstructure observation shows that the two composites all consist of body-centered cubic β-Ti and face-centered cubic (Cu, Ni)–Ti₂ regions but have opposite matrix and reinforcing phases. Meanwhile, mechanical property examination indicates that the composites for x = 0.35 exhibit far higher fracture strength and far larger fracture strain compared with the composites for x = 0.55 fabricated under the same parameter conditions. The different mechanical properties for the two composites can be explained by the different fracture mechanisms resulted from their different microstructures.     

Microstructural and compositional study of a bulk Pb(Mg1/3Nb2/3)O3–PbTiO3 single crystal grown from a BaTiO3 seed

The microstructure, composition and homogeneity of a Pb(Mg_1/3Nb_2/3)O₃–PbTiO₃ (PMNT) single crystal were studied using a combination of electron-microprobe techniques: scanning electron microscopy, orientation analysis and quantitative X-ray microanalysis. A PMNT single crystal was grown from a polycrystalline PMNT matrix using a BaTiO₃ single crystal as a seed. The PMNT crystal retained the same crystallographic orientation as the seed with no interdiffusion at the interface. The average chemical composition, determined with optimized quantitative wavelength-dispersive X-ray microanalysis, was Pb(Mg_1/3Nb_2/3)_1−XTi_XO₃ where x = 0.33. A statistical evaluation of the data using the analysis of variance showed that the achieved experimental uncertainty was below ± 1% relative. The compositional homogeneity of the crystal was verified on the micrometer-scale; however on the macro-scale slight fluctuations of the Mg, Nb and Ti concentrations were observed across the crystal. The measured variations from the average composition were ± 2.3% relative for Ti, ± 1.3% for Nb and ± 1.4% for Mg. In contrast, the Pb concentration was found to be uniform on both the micro- and macro-scale, showing a variation below ± 0.5% relative.     

Formation mechanism of Ti2AlC under the self-propagating high-temperature synthesis (SHS) mode

Ti₂AlC was fabricated by the self-propagating high-temperature synthesis (SHS) technique from a compacted powder mixture consisting of Ti:Al:C = 2:1:1 (molar ratio) of mortar mixing, planetary mixing and various packing densities. A thermocouple was placed directly into the green compact body in order to monitor the combustion temperature during the SHS process. When the green compact with planetary mixing treatment and a packing density of 17% as well as 60% was used, propagation of the reaction exothermicity could occur, and the starting compact completely changed to Ti₂AlC. Formation mechanism of Ti₂AlC using a SHS technique was discussed. In addition, the melting point of the resultant sample was determined to be 1570 °C.     

Friction and wear behavior of polytetrafluoroethene composites filled with Ti3SiC2

In this work, polytetrafluoroethylene (PTFE) composites filled with Ti₃SiC₂ or graphite were prepared through powder metallurgy. The effects of different filling components, loads and sliding velocities on the friction performance of Ti₃SiC₂/PTFE composites were studied. Ti₃SiC₂/PTFE composites exhibit better wear resistance than graphite/PTFE composites due to the better mechanical properties of Ti₃SiC₂. The wear resistance was found to improve around 100× over unfilled PTFE with the addition of 1 wt.% Ti₃SiC₂. In addition, the 10 wt.% sample had the lowest wear rate of K = 2.1 × 10⁻⁶ mm³/Nm and the lowest steady friction coefficient with μ = 0.155 at the condition of 90 N–0.4 m/s. Ti₃SiC₂ was proved to promote the formation of a thin and uniform transfer film on counterpart surface and a protection oxide film on worn surface, which are the key roles for improving wear resistance.     

Fabrication and characterization of 3-D Cf/ZrC composites by low-temperature liquid metal infiltration

Three-dimensional braided carbon fiber-reinforced ZrC matrix composite, 3-D C_f/ZrC, were prepared by liquid metal infiltration process at 1200 °C using a Zr₂Cu intermetallic compound as infiltrator. The microstructure and properties of the composites were investigated. The results indicated that ZrC with a yield of 35.2 ± 1.8 vol.% was certified as the major phase of the composites. The formation of ZrC was controlled by a solution-precipitation mechanism. The obtained composites exhibited good mechanical properties, with a flexural strength of 293.0 ± 12.1 MPa, a flexural modulus of 82.7 ± 6.4 GPa and a fracture toughness of 9.8 ± 0.9 MPa m^1/2. The mass and linear ablation rates of the composites exposed to oxyacetylene torch were 0.0013 ± 0.0005 g s⁻¹ and −0.0009 ± 0.0003 mm s⁻¹, respectively. The formation of a dense ZrO₂ protective layer and the evaporation of residual Cu contributed mainly to the excellent ablation resistance.     

Structural,magnetic and microwave absorption characteristics of BaCoxMnxTi2xFe12 − 4xO19

The effect of Mn⁺²Co⁺²Ti⁺⁴ substitution on microwave absorption has been studied for BaCo_xMn_xTi_2xFe_12 ? 4xO₁₉ ferrite–acrylic resin composites, where x varies from 0.3 to 0.5 in steps of 0.1, in frequency range from 12 to 20 GHz. X-ray diffraction (XRD), scanning electron microscope (SEM), vibrating sample magnetometer, and vector network analyzer were used to analyze the structures, electromagnetic and microwave absorption properties. The results showed that, the magnetoplumbite structures for all samples have been formed. Based on microwave measurement on reflectivity, BaCo_xMn_xTi_2xFe_12 ? 4xO₁₉ may be a good candidate for electromagnetic compatibility and other practical applications at high frequency.     

Microwave dielectric properties of Ba(Mg1/3Ta(2−2x)/3Wx/3Tix/3)O3 ceramics

The microwave dielectric properties of ceramics based on Ba(Mg_1/3Ta_(2−2x)/3W_x/3Ti_x/3)O₃ is investigated as a function of x. The densification as well as dielectric properties deteriorate with increase in the substitution levels of (Ti_1/3W_1/3)^3.33+ at (Ta_2/3)^3.33+ site in Ba(Mg_1/3Ta_2/3)O₃. The τ_f is approaching zero between x = 0.1 and 0.15 in Ba(Mg_1/3Ta_(2−2x)/3W_x/3Ti_x/3)O₃ where quality factor is reasonably good (Q_u × f = 80,000–90,000 GHz). The Ba(Mg_1/3Ta_(2−2x)/3W_x/3Ti_x/3)O₃ with x = 1.0 has ɛ_r = 15.4, τ_f = −25.1 ppm/°C, Q_u × f = 35,400 GHz.     

Phase relations and high temperature-XRD studies of Gd2−xNdxTi2O7 solid solutions

A series of compositions with the general formula Gd_2−xNd_xTi₂O₇ (0.0 ≤ x ≤ 2.0) was prepared by ceramic sintering and characterized by powder XRD. Nd³⁺ has been used as a surrogate for Am³⁺, an actinide found in spent nuclear fuel. One end member, Gd₂Ti₂O₇, had the pyrochlore structure and formed solid solutions with Nd₂Ti₂O₇ up to the nominal composition Gd_1.2Nd_0.8Ti₂O₇. An increase in lattice parameter was observed as a function of x in the series Gd_2−xNd_xTi₂O₇ in the composition range 0.0 ≤ x ≤ 0.8. Compositions Gd_2−xNd_xTi₂O₇ in the range 0.8 ≤ x ≤ 1.4 were biphasic. From x ≥ 1.6, the solid solutions are monoclinic, isotypic with Nd₂Ti₂O_7. These results were explained based on the radius (r_A/r_B) ratio of the cations. High temperature-XRD studies on cubic pyrochlores showing thermal expansion are reported.     

Pseudo-quinary Ti20Zr20Hf20Be20(Cu20 -xNix) high entropy bulk metallic glasses with large glass forming ability

A series of pseudo-quinary Ti₂₀Zr₂₀Hf₂₀Be₂₀(Cu_20 -xNi_x) (x = 2.5, 5, 7.5, 10, 12.5, 15, 17.5 and 20 at.%) high entropy bulk metallic glasses (HE-BMGs) with large glass forming ability (GFA) were successfully prepared by copper mold tilt-casing. The critical diameters (D_c) of these HE-BMGs are all above 12 mm. In particular, the developed Ti₂₀Zr₂₀Hf₂₀Be₂₀(Cu_7.5Ni_12.5) and Ti₂₀Zr₂₀Hf₂₀Be₂₀Ni₂₀ high entropy alloys (HEAs) can be produced in the amorphous state with diameters up to 30 mm and 15 mm, respectively, which are the largest HE-BMG and quinary HE-BMG hitherto. The two HE-BMGs also exhibit high yield strength, together with the plastic strain values of (3.0 ± 1.1) % and (4.0 ± 0.9) %, respectively. With increasing Ni additions in the pseudo-quinary HEAs, the crystallization growth resistance and thermal stability have been improved, which is apparently due to the sluggish diffusion of the atoms in the HEAs.     

The effect of Mg add on morphology and mechanical properties of Al–xMg/10Al2O3 nanocomposite produced by mechanical alloying

Effect of Mg content on microstructure and mechanical properties of Al–xMg/10 wt.%Al₂O₃ (x = 0, 5, 10 and 15 wt.%) powder mixtures during milling was investigated. The results show that for the binary Al–Mg matrix, the predominant phase was an Al–Mg solid solution. With the increment of Mg to 15 wt.% the crystallite sizes of 20 h milled powders diminish from 44 to 26 nm and lattice strains increased from 0.22% to 0.32% caused by Mg atomic penetration into the substitution sites of the Al lattice. With up to 15 wt.% Mg (for 20 h milled composites) microhardness increases from 120 to 230 HV caused by the increment of the Mg concentration and dislocation density as well as the decrease of the crystallite size.     

Microwave-assisted synthesis and characterization of Ti1 − xVxO2 (x = 0.0–0.10) nanopowders

Ti_1 ? xV_xO₂ (x = 0.0–0.10) nanopowders were successfully synthesized by a microwave-assisted sol–gel technique and their crystal structure and electronic structure were investigated. The products were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman and UV–Vis spectroscopy. The results revealed that TiO₂ powders maintained the anatase phase for calcination temperature below 600 °C, but gradually changed to the rutile phase above 800 °C. The formation of the rutile phase was completed at 1000 °C. For Ti_1 ? xV_xO₂ (x = 0.05) powders, the phase transformation appeared at 600 °C. The absorption edge of Ti_1 ? xV_xO₂ (x > 0) powders broadened to the visible region with increasing V concentration and a strong visible light absorption was obtained with 10% V doping. V doping and subsequent coexistence of both anatase and rutile phases in our Ti_1 ? xV_xO₂ nanoparticles are considered to be responsible for the enhanced absorption of visible light up to 800 nm.     

Effects of solids loading on microstructure and mechanical properties of HfB2–20 vol.% MoSi2 ultra high temperature ceramic composites through aqueous gelcasting route

HfB₂–20 vol.% MoSi₂ ultra high temperature ceramic composites were prepared through aqueous gelcasting route. The stability of HfB₂ and MoSi₂ suspensions were studied by zeta potential measurements, sedimentation tests and apparent viscosity measurements. The solids loading had significant effects on the green and sintered densities, microstructure and mechanical properties of HfB₂–MoSi₂ composites. The values of flexural strength of the green and sintered bodies ranged from 18.3 to 38.7, and 111.5 to 415.9 MPa, respectively, which were strongly dependent on the solids loading. The values of fracture toughness of the sintered bodies ranged from 2.18 to 4.24 MPa m^1/2. The highest relative density, mechanical properties and the most homogeneous microstructure was obtained when the solids loading was 45 vol.%. The highest green strength, flexural strength and fracture toughness were 38.7 ± 5.3 MPa, 415.9 ± 17.0 MPa and 4.24 ± 0.22 MPa m^1/2, respectively.     

Microwave dielectric characteristics of Mg(Ta1−xNbx)2O6 ceramics

The crystalline phase and the microwave dielectric properties of the Mg(Ta_1−xNb_x)₂O₆ ceramics have been investigated. Combining the positive temperature coefficient of the resonant frequency (τ_f) material (MgTa₂O₆, τ_f = +30 ppm/°C) with the negative one (MgNb₂O₆, τ_f = −70 ppm/°C) can produce the composite with τ_f ∼ 0 ppm/°C. The crystal structure of pure MgTa₂O₆ ceramic is the tetragonal structure. For x = 0.15, the crystal structure of the solid solution was the coexistence of the tetragonal structure and orthorhombic structure. Solid solutions with 0.25 ≦ x ≦ 1 exhibit the orthorhombic structure, which is like the structure of pure MgNb₂O₆ ceramic. The sintered morphologies of Mg(Ta_1−xNb_x)₂O₆ ceramics gradually change from the disk-typed grains (x = 0 and 0.15) to the disk-typed and bar-typed grains coexist (x = 0.35, 0.5, and 0.7), and then reveal the bar-typed grains (x = 0.85 and 1). The densities, dielectric constants (ɛ_r) and τ_f values of Mg(Ta_1−xNb_x)₂O₆ ceramics decrease with the increase of the MgNb₂O₆ content. The quality factor (Q × f) reaches the minimum value at x = 0.15, and then increases with the increase of the MgNb₂O₆ content. The Mg(Ta_1−xNb_x)₂O₆ ceramic with x = 0.25 sintered at 1450 °C exhibits a minimum τ_f value of −0.7 ppm/°C.     

Microwave dielectric properties of Ba3La2Ti2Nb2−xTaxO15 ceramics

High dielectric constant and low loss ceramics in the system Ba₃La₂Ti₂Nb_2−xTa_xO₁₅ (x = 0–2) have been prepared by conventional solid-state ceramic route. Ba₃La₂Ti₂Nb_2−xTa_xO₁₅ solid solutions adopted A₅B₄O₁₅ cation-deficient hexagonal perovskite structure for all compositions. The materials were characterized at microwave frequencies. They show a linear variation of dielectric properties with the value of x. Their dielectric constant varies from 49.8 to 45.1, quality factor Q_u × f from 22,000 to 31,040 GHz and temperature variation of resonant frequency from + 6.9 to − 13.4 ppm/°C as the value of x increases. These low loss ceramics might be used for dielectric resonator (DR) applications.     

Microstructure and mechanical properties of in situ TiC and Nd2O3 particles reinforced Ti–4.5 wt.%Si alloy composites

(TiC + Nd₂O₃)/Ti–4.5 wt.%Si composites were in situ synthesized by a non-consumable arc-melting technology. The phases in the composites were identified by X-ray diffraction. Microstructures of the composites were observed by optical microscope and scanning electron microscope. The composite contains four phases: TiC, Nd₂O₃, Ti₅Si₃ and Ti. The TiC and Nd₂O₃ particles with dendritic and near-equiaxed shapes are well distributed in Ti–4.5 wt.%Si alloy matrix, and the fine Nd₂O₃ particles exist in the network Ti + Ti₅Si₃ eutectic cells and Ti matrix of the composites. The hardness and compressive strength of the composites are markedly higher than that of Ti–4.5 wt.%Si alloy. When the TiC content is fixed as 10 wt.% in the composites, the hardness is enhanced as the Nd₂O₃ content increases from 8 wt.% to 13 wt.%, but the compressive strength peaks at the Nd₂O₃ content of 8 wt.%.     

Synergetic lubricating effect of MoS2 and Ti3SiC2 on tribological properties of NiAl matrix self-lubricating composites over a wide temperature range

NiAl matrix self-lubricating composites with MoS₂ and Ti₃SiC₂ lubricants were prepared by spark plasma sintering. The tribological behaviors of the NiAl–Ti₃SiC₂–MoS₂ composites against Si₃N₄ were investigated from room temperature to 800 °C. The results showed that the composites exhibited excellent self-lubricating and anti-wear properties over a wide temperature range. At 400 °C, the composites containing 5Ti₃SiC₂–5MoS₂ (wt.%) had a very low friction coefficient of about 0.13 and a low wear rate of 4.5 × 10⁻⁵ mm³ N⁻¹ m⁻¹. MoS₂ played the main role of lubrication at low temperatures, while Ti₃SiC₂ was responsible for low friction at high temperatures. Ti₃SiC₂ and MoS₂ lubricants in the NiAl–Ti₃SiC₂–MoS₂ composites showed the excellent synergetic lubricating effect over a wide temperature range from room temperature to 800 °C.     

Microstructure and ferroelectric properties of dysprosium-doped bismuth titanate thin films

Bi₄Ti₃O₁₂ (BIT) ferroelectric thin films with Dy³⁺ substitution (Bi_4−xDy_xTi₃O₁₂, x = 0, 0.2, 0.4, 0.6, 0.8 and 1.0, respectively) were grown on Pt(111)/Ti/SiO₂/Si(100) substrates using sol–gel method. X-ray diffraction (XRD) and scanning electron microscopy (SEM) revealed that after annealing at 710 °C for 10 min, all Bi_4−xDy_xTi₃O₁₂ films became polycrystallites. Among all the deposited thin films, the Bi_3.4Dy_0.6Ti₃O₁₂ specimen exhibits improved ferroelectric properties with the largest average remanent polarization (2Pr) of 53.06 μC/cm² under applied field of 400 kV/cm and fatigue free characteristics (16% loss of 2Pr after 1.5 × 10¹⁰ switching cycles), indicating that it is suitable for non-volatile ferroelectric random access memories applications.