Preparation and high‐temperature behavior of HfC–SiC nanocomposites derived from a non‐oxygen single‐source‐precursor

A single‐source precursor for the preparation of HfC‐SiC ceramics was synthesized via a Grignard reaction using bis(cyclopentadienyl)hafnium(IV) dichloride, trans‐1,4‐dibromo‐2‐butene, and (chloromethyl)trimethylsilane as raw materials. The composition, structure, pyrolysis process and high‐temperature behavior of the precursor were investigated. The results show that the precursor with a backbone comprising Hf–C, Si–C and CH=CH groups exhibits good solubility in common solvents, such as tetrahydrofuran, dimethylbenzene, and chloroform. Pyrolysis of the precursor at 1000°C yielded a microcrystalline HfC phase with a ceramic yield of 63.86 wt%. The pyrolytic products at 1600°C were HfC–SiC nanocomposite ceramics, which exhibited good thermal stability up to 2400°C. The formation of a (Hf,Si)C solid‐solution would be beneficial for densification during the sintering process. The non‐oxygen structure, high ceramic yield, homogeneous composition and excellent high‐temperature behavior of the pyrolytic products make the as‐prepared precursor a promising material for the preparation of high‐performance ultra‐high‐temperature ceramics.     

The microstructure and electromagnetic wave absorption properties of near-stoichiometric SiC fibre

The microstructure and electromagnetic (EM) properties of near-stoichiometric SiC fibres (with C/Si ratio of 1.125) were analyzed and evaluated in detail. The SiC fibres consisted of β-SiC nanocrystallines and free carbon, and exhibited a uniquely specific skin-core structure with thin carbon layer of 5 nm on their surfaces. The relative complex permittivity increased with the increasing fibre volume fraction from 13 vol% to 27.5 vol%. The imaginary part of permittivity increased from 1.36 to 2.13 at 10 GHz, due to more SiC nanocrystallines and interfaces generating. The EM wave absorption properties were enhanced by the increasing fibre volume fraction and the effective absorption bandwidth was approximately 2.6 GHz when the fibre volume fraction was 27.5 vol%.     

Single-source-precursor synthesis,microstructure and high temperature behavior of TiC-TiB2-SiC ceramic nanocomposites

Newly developed TiC-TiB₂-SiC ceramic nanocomposites were successfully synthesized by a novel single-source-precursor approach, with allylhydridopolycarbosilane (AHPCS), bis(cyclopentadienyl) titanium dichloride (Cp₂TiCl₂) and triethylamine borane (TEAB) as starting materials. The obtained single-source-precursor was characterized by Fourier transform infrared spectra (FT-IR), which confirms that hydroboration (C=C/B-H) and dehydrochlorication (Si-H/Cp₂TiCl₂) reactions were involved to introduce B and Ti elements into the AHPCS chains. The structural evolution of single-source-precursors, phase composition and chemical composition of the obtained ceramics were investigated by FT-IR, X-ray diffraction (XRD) and elemental analysis. High temperature behavior of the resultant TiC-TiB₂-SiC ceramic nanocomposites with respect to decomposition as well as crystallization was carefully checked by XRD and mass loss after annealing at high temperatures of 1600 and 1800 °C. Transmission electron microscopy (TEM) was used to further observe the microstructure of TiC-TiB₂-SiC nanocomposites, which again confirms the crystalline phases consist of nanoscaled β-SiC, TiC and TiB₂.     

Structure‐properties relationship in resol/montmorillonite nanocomposites

Polymer/layered silicate nanocomposites were prepared, adding modified, and nonmodified montmorillonites to a resol resin. It was observed that the composites exhibited an intercalated disordered structure by means of X‐ray diffraction (XRD) and transmission electronic microscopy. The crosslinking density of the resol network was greatly influenced by the presence and type of clay that was added to the resin. The composites filled with the modified montmorillonites showed a lower glass transition temperature value as well as a higher degradation peak at ～ 400°C, which is characteristic of the degradation of methylene bridges, indicating a decrease in the crosslinking density of the resol network when modified clays are added. Resol/unmodified montmorillonite composites exhibited different behavior comparing to the other composites and the resol. A higher thermal resistance was observed in the fragmentation zone and a different tan δ response was seen in the DMA analysis. These differences in the behavior of the composites could be because of the interaction between the resol prepolymer and the clay modifiers and as a result of their chemical compatibility. The hardness and elastic modulus of the resol were improved with the addition of clays. However, higher values were obtained for the composite made with the more dispersed montmorillonite. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and structure and mechanical properties of poly(styrene‐b‐butadiene)/clay nanocomposites

Star‐shaped and linear block thermoplastic poly(styrene‐b‐butadiene) copolymer (SBS)/organophilic montmorillonite clays (OMMT) were prepared by a solution approach. The intercalation spacing in the nanocomposites and the degree of dispersion of nanocomposites were investigated by X‐ray diffraction (XRD) and transmission electron microscopy (TEM), respectively. The mechanical properties, dynamic mechanical properties, and thermal stability of these nanocomposites were determined. Results showed that SBS chains were well intercalated into the clay galleries and an intercalated nanocomposite was obtained. The mechanical strength of nanocomposites with the star‐shaped SBS/OMMT were significantly increased. The addition of OMMT also gave an increase of the elongation, the dynamic storage modulus, the dynamic loss modulus, and the thermal stability of nanocomposites. The increase of the elongation of nanocomposites indicates that SBS has retained good elasticity. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3430–3434, 2004     

Preparation and mechanical properties of acrylonitrile‐butadiene‐styrene copolymer/clay nanocomposites

Bis(3‐triethoxysilylpropyl) tetrasulfane (TSS) was reacted with the silanol groups of the commercially available clay, Closite®25A (C25A) to prepare TSS‐C25A, which was melt‐compounded with acrylonitrile‐butadiene‐styrene copolymer (ABS). The tetra sulfide groups of TSS‐C25A may chemically react with the vinyl groups of ABS to enhance the interaction between the clay and ABS. The ABS/clay composites exhibited much higher tensile strength and elongation at break than the neat ABS. Especially the elongation at break of ABS/TSS‐C25A composite was 5 times higher than that of neat ABS. The X‐ray diffraction patterns of the clay showed that the d₀₀₁ basal spacing was enlarged from 1.89 nm to 2.71–2.86 nm as a result of the compounding with ABS. According to the thermogravimetric analysis, the thermal decomposition of the composite took place at a slightly higher temperature than that of neat ABS. Intercalated/exfoliated coexisting structures were observed by transmission electron microscopy for the ABS/clay composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Dielectric and electromagnetic interference shielding properties of zeolite 13X and carbon black nanoparticles based PVDF nanocomposites

In the present work, Zeolite 13X and carbon black nanoparticles (CBNPs) reinforced polyvinylidene fluoride (PVDF) nanocomposites were obtained by a simple solvent casting technique. The structural, morphological and thermal properties of PVDF/Zeolite 13X/CBNPs nanocomposites with various loadings of Zeolite 13X and CBNPs were investigated using Fourier-transform infrared spectroscopy, X-ray diffraction, Scanning electron microscopy and thermo-gravimetric analysis. The dielectric studies were carried out in the 50 Hz–10 MHz frequency range at room temperature. The electromagnetic interference (EMI) shielding effectiveness (SE) of PVDF/Zeolite 13X/CBNPs nanocomposite was investigated in the 8–18 GHz frequency region (X-band and Ku-band). The maximum EMI SE of approximately −11.1 dB (8–12 GHz) and −11.5 dB (12–18 GHz) was observed for PVDF/CBNPs nanocomposites with 10 wt% loading of CBNPs. These findings emphasize the application of PVDF/Zeolite 13X/CBNPs nanocomposites as a potential EMI shielding material.     

Influence of graphite nanosheets on the structure and properties of PVC‐based nanocomposites

Polyvinyl chloride‐ (PVC)‐ based nanocomposites, containing graphite nanosheets (G), which may be used as electromagnetic wave absorbers was developed and investigated. The microstructure of polyvinyl chloride/graphite nanocomposites (PVC/G) were examined by means of X ‐ray diffraction, scanning electron microscopy (SEM), and thermal gravimetric analyses (TGA). SEM image reveals that the graphite nanosheets were well dispersed in the PVC matrix without agglomeration. Thermal stability of the PVC/G nanocomposites is improved as a result of inclusion of graphite nanosheets. The PVC/G nanocomposites were characterized to investigate the effect of dispersion of graphite nanosheets in PVC matrix. The dielectric spectroscopy of PVC/G nanocomposites in frequency range from 1 to 12 GHz has been performed. The results show that PVC/G nanocomposites exhibit high dielectric constant at the measured frequencies. Coefficient of attenuation and coefficient of reflection of PVC/G composites have been also examined in a frequency range from 1 to 12 GHz. The electromagnetic interference shielding effectiveness (EMI) depends on graphite volume fraction in the composite. The results show that the PVC/G represents a new class of conducting lightweight nanomaterial that can absorb electromagnetic waves at microwave frequency and may be promising for future commercial use. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of clay on properties of polyimide‐clay nanocomposites

Effect of clay on mechanical, thermal, moisture absorption, and dielectric properties of polyimide‐clay nanocomposites was investigated. Nanocomposites of polyimide (ODA‐BSAA) hybridized with two modified clay (PK‐802 and PK‐805) were synthesized for comparison. The silicate layers in the polymer matrix were intercalated/exfoliated as confirmed by wide‐angle X‐ray diffraction and transmission electron microscopy. Thermal stability, moisture absorption, and storage modulus for these nanocomposites are improved as hybridized clay increases. Reduced dielectric constants due to the hybridization of layered silicates are observed at frequencies of 1 kHz–1 MHz and temperatures of 35–150°C. The tetrahedrally substituted smectite (PK‐805) resulted in higher mechanical strength and dielectric constants than those of octahedrally substituted smectite (PK‐802), which could be attributed to their stronger ionic bonding between clay layer and polymer matrix. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 318–324, 2007     

Effect of the structure of silane‐coupling agent on dynamic mechanical properties of dental resin‐nanocomposites

This work was aimed at the study by dynamic mechanical analysis (DMA) of dental composites consisted of a Bis‐GMA/TEGDMA (50/50 wt/wt) matrix and silica nanoparticles (Aerosil OX50) as filler, silanized with various silanes. The silanes used were 3‐[(1,3(2)‐dimethacryloyloxypropyl)‐2 (3)‐oxycarbonylamido] propyltriethoxy‐silane (UDMS), 3‐methacryloxypropyl‐trimethoxysilane (MPS), octyltrimethoxysilane (OTMS), blends of UDMS/OTMS (50/50 wt/wt), or MPS/OTMS (50/50 wt/wt). The total amount of silane was kept constant at 10% by weight fraction relative to the filler weight. The silanized nanoparticles were mixed with the dimethacrylate matrix (60% filler by weight fraction). The composites were light cured and tested by DMA for the determination of storage modulus (E′), loss modulus (E″), tangent delta (tan δ), and glass transition temperature (T_g). Measurements were performed in samples immediately after curing and samples stored in water at 37°C for 1, 7, 30, or 120 days. OTMS‐composite in which OTMS does not form covalent bond with the dimethacrylate matrix showed lower elastic modulus both in dry and wet conditions. The ability of bifunctional UDMS for crosslinking was found not to increase the elastic behavior of the composite, as it was expected, compared with that of MPS‐composite, because of the high amount of the silane used. After immersion in water the elastic modulus of OTMS‐composite remained constant, while that of the other composites increased after 1 day and then remained constant up to 120 days. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Dielectric properties of nylon 6/clay nanocomposites from on-line process monitoring and off-line measurements

Nylon 6/clay nanocomposites were studied by dielectric relaxation spectroscopy (DRS) to correlate morphology and microstructure with relaxation behavior of the polymer matrix at the molecular level. Partially exfoliated clay microstructure was achieved by extruding nylon 6 with surfactant-treated montmorillonite clays. A new on-line dielectric slit die sensor was used to examine the melt state properties during extrusion compounding. Solid state properties were probed by off-line DRS over a temperature range from −50 to 180 °C in a frequency range from 10⁻³ to 10⁶ Hz. Using non-linear regression methods in conjunction with the temperature-frequency positions of relaxations observed in the dielectric loss data, the experimental data were fit with the Havriliak-Negami and Cole-Cole dielectric relaxation functions corrected for electrode polarization and DC conductivity. Characteristic frequency, relaxation strength, and DC conductivities were extracted from curves with overlapping relaxation modes. Two dielectric relaxations were observed in the composite melt: the α relaxation associated with molecular segmental motion, and a Maxwell-Wagner relaxation (MW) resulting from interfacial polarization at the resin/clay interface. Analysis of the solid-state data yielded a comprehensive master plot of dielectric relaxations attributed to segmental and local molecular dynamics and other relaxations resulting from water and Maxwell-Wagner interfacial polarization. The impact of clay fillers is seen in nearly all relaxation processes changing both characteristic frequency and strength of the relaxation.     

Morphology and thermo‐mechanical properties of compatibilized polyimide‐silica nanocomposites

Polyimide‐silica nanocomposites have been prepared from an aromatic polyamic acid derived from pyromellitic dianhydride and oxydianiline and a silica network using the sol‐gel reaction. Compatibilization of the two components was achieved by modifying the silica network with imide linkages. Morphology, thermal, and mechanical properties of these composite materials were studied as a function of silica content and compared with the one in which reinforcement of the polyimide was achieved using a pure silica network. There was considerable reduction in the silica particle size with more homogeneous distribution in the matrix when imide spacer groups were introduced in the silica network. The tan δ spectra obtained from dynamic thermal mechanical analysis shows a large increase in the glass transition temperature with increasing silica content for the compatibilized system in contrast to the un‐compatibilized one. Mechanical properties of the polyimide composites improved due to better interaction between the organic and inorganic phases. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2521–2531, 2005     

Electrical and mechanical properties of carbon nanotube‐epoxy nanocomposites

In this work, electrical conductivity and thermo‐mechanical properties have been measured for carbon nanotube reinforced epoxy matrix composites. These nanocomposites consisted of two types of nanofillers, single walled carbon nanotubes (SW‐CNT) and electrical grade carbon nanotubes (XD‐CNT). The influence of the type of nanotubes and their corresponding loading weight fraction on the microstructure and the resulting electrical and mechanical properties of the nanocomposites have been investigated. The electrical conductivity of the nanocomposites showed a significantly high, about seven orders of magnitude, improvement at very low loading weight fractions of nanotubes in both types of nanocomposites. The percolation threshold in nanocomposites with SW‐CNT fillers was found to be around 0.015 wt % and that with XD‐CNT fillers around 0.0225 wt %. Transmission optical microscopy of the nanocomposites revealed some differences in the microstructure of the two types of nanocomposites which can be related to the variation in the percolation thresholds of these nanocomposites. The mechanical properties (storage modulus and loss modulus) and the glass transition temperature have not been compromised with the addition of fillers compared with significant enhancement of electrical properties. The main significance of these results is that XD‐CNTs can be used as a cost effective nanofiller for electrical applications of epoxy based nanocomposites at a fraction of SW‐CNT cost. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Thermal and mechanical properties of nanocomposites based on a PLLA‐b‐PEO‐b‐PLLA triblock copolymer and nanohydroxyapatite

Composites which combine biocompatible polymers and hydroxyapatite are unique materials with regards to their mechanical properties and bioactivity in the development of temporary bone‐fixation devices. Nanocomposites based on a biocompatible and amphiphilic triblock copolymer of poly(l‐ lactide) (PLLA) and poly(ethylene oxide) (PEO) —PLLA‐b‐PEO‐b‐PLLA— and neat (nHAp) or PEO‐modified (nHAp@PEO) hydroxyapatite nanoparticles were prepared by dispersion in benzene solutions, followed by freeze‐drying and injection moulding processes. The morphology of the copolymers of a PEO block dispersed throughout a PLLA matrix was not changed with addition of the nanofillers. The nHAp particles were spherical and, after modification, the nHAp@PEO nanoparticles were partially agglomerated. In the nanocomposites, these particles characteristics remained unchanged, and the nHAp particles and nHAp@PEO agglomerates were uniformly dispersed through the copolymer matrix. These particles acted as nucleating agents, with nHAp@PEO being more efficient. The incorporation of nHAp increased both the reduced elastic modulus (～22%) and the indentation hardness (～15%) in comparison to the copolymer matrix, as determined by nanoindentation tests, while nHAp@PEO addition resulted in lower increments of these mechanical parameters. The incorporation of untreated nHAp was, therefore, more beneficial with regards to the mechanical properties, since the amphiphilic PLLA‐b‐PEO‐b‐PLLA matrix was already efficient for nHAp nanoparticles dispersion. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44187.     

Poly(trimethylene terephthalate‐block‐tetramethylene oxide) elastomer/single‐walled carbon nanotubes nanocomposites: Synthesis,structure, and properties

Nanocomposites based on poly(trimethylene terephthalate)‐block‐poly(tetramethylene oxide) (PTT‐PTMO)‐segmented copolymer and COOH‐functionalized single‐walled carbon nanotubes (SWCNTs) were prepared by in situ polymerization method. The obtained nanocomposites were characterized by thermogravimetric analysis, scanning electron microscopy, differential scanning calorimetry (DSC), DMTA, wide‐angle x‐ray scattering (WAXS), small‐angle X‐ray scattering, and tensile testing. The nanocomposites with low SWCNTs loading (<0.5 wt %) shows uniform dispersion of CNT in polymer matrix. As the SWCNTs loading in the nanocomposites increase, the significant improvement of thermo‐oxidative stability was observed. It was found that the nanocomposites have slightly higher degree of crystallinity (determined by DSC and WAXS) of poly(trimethylene terephthalate) (PTT) hard phase than neat PTT‐PTMO copolymer. The melting point of PTT hard phase and glass transition temperature of poly(tetramethylene oxide)‐rich phase were not affected by the presence of CNTs in polymer matrix. The SWCNTs played a role as nucleating agent in PTT‐PTMO matrix, which led to increase in the crystallization rate. Tensile tests showed that the tensile strength of the nanocomposites with 0.05–0.3 wt % loading of SWCNTs have improved tensile strength in comparison to the neat PTT‐PTMO copolymer without reduction elongation at break. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of diblock copolymer surfactant on the microstructure and EM properties of CNT nanocomposites

Carbon nanotubes (CNTs) were chosen due to their excellent electrical properties. As delivered, CNTs are highly agglomerated, and to exploit their high aspect ratio is then necessary to disagglomerate them as much as possible. A diblock copolymer surfactant was used to aid CNT disagglomeration. Disagglomeration in solvent was assessed by TEM, whereas composite microstructure was observed by scanning electron microscopy. X‐band waveguide measurements were carried out to assess complex permittivity and absorbing performance. On a same weight percent of filler basis, samples produced with the aid of surfactant show higher real permittivity than samples produced without. An equivalent circuit analogy is suggested to explain the results and relates composite microstructure with macroscopic permittivity. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of the processing temperature on the nanostructure and mechanical properties of PCTG‐based nanocomposites

The influence of the processing temperature on both the dispersion level and the mechanical properties of the amorphous copolyester (PCTG)/organoclay (Cloisite® 20A) nanocomposite (NC) is studied in this article. At high processing temperatures, no change in the chemical nature of the matrix was observed, but its molecular weight decreased. Widely dispersed structures were observed by wide angle X‐ray diffraction (WAXD) and transmission electron microscopy whatever the processing temperature might be. Dispersion was greatest for the samples processed at 200°C due to the highest viscosity of these samples and decreased at higher processing temperatures (T_p). These different dispersion levels led to a large modulus increase (71%) after processing at 200°C and to lower ones (about 50%) after processing at 230 and 260°C. The ductility of the NCs decreased at lower processing temperatures. The decrease was attributed to the greater stiffness of the matrix, and was not significant enough to modify the ductile nature of the NCs, which showed clear yield points even at the lowest processing temperature (200°C). © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Morphology,mechanical properties and electromagnetic shielding effectiveness of poly(styrene‐b‐ethylene‐ran‐butylene‐b‐styrene)/carbon nanotube nanocomposites: effects of maleic anhydride,carbon nanotube loading and processing method

Nanocomposites based on poly(styrene‐b‐ethylene‐ran‐butylene‐b‐styrene) (SEBS) and carbon nanotubes (CNTs) (SEBS/CNT) as well as SEBS grafted with maleic anhydride (SEBS‐MA)/CNT were successfully prepared for electromagnetic shielding applications. Both SEBS/CNT and SEBS‐MA/CNT nanocomposites were prepared by melt compounding and were post‐processed using two different techniques: tape extrusion and compression moulding. The different nanocomposites were characterized by Raman spectroscopy and rheological analysis. Their mechanical properties, electrical properties (10^-2–10⁵ Hz) and electromagnetic shielding effectiveness (8.2–12.4 GHz) were also evaluated. The results showed that the CNT loading amount, the presence of MA in the matrix and the shaping technique used strongly influence the final morphologies and properties of the nanocomposites. Whilst the nanocomposite containing 8 wt% CNTs prepared by compression moulding presented the highest electromagnetic shielding effectiveness (with a value of 56.73 dB, which corresponds to an attenuation of 99.9996% of the incident radiation), the nanocomposite containing 5 wt% CNTs prepared by tape extrusion presented the best balance between electromagnetic and mechanical properties and was a good candidate to be used as an efficient flexible electromagnetic interference shielding material. © 2018 Society of Chemical Industry     

Molten-salt-assisted combustion synthesis of B4C powders: Synthesis mechanism and dielectric and electromagnetic wave absorbing properties

A novel electromagnetic wave (EMW) absorber was prepared by combustion synthesis. Boron carbide (B₄C) powders with different grain sizes using a molten-salt-assisted combustion technique with B₂O₃, CB (carbon black), and Mg powders as starting materials, and NaCl as an additives. The effects of the NaCl content on the phase compositions and the microstructure of the products were characterized. A combustion front quenching method was used to elucidate the mechanism for the B₄C powders synthesis. The dielectric, and EMW absorbing properties in the X-band were also investigated. The results showed that the addition of NaCl significantly reduced the grain size of B₄C powders. Nanoscale B₄C powders with cubic polyhedral structures were synthesized using 6 wt% NaCl (labeled as N-6). According to the quenching test results can be obtained that the first step in the combustion synthesis was melting B₂O₃ into a glassy substance. At the same time, Mg melted and formed a liquid pool into which the NaCl dissolved, followed reduction of the B₂O₃ to B. The formed B eventually reacted with CB to form B₄C, and the B₄C particles precipitated from the matrices. The N-6 sample exhibits optimal dielectric and EMW absorbing properties, because of a high specific surface area that enhances interfacial and space charge polarization.     

Thermal and mechanical properties of plasticized poly(L‐lactide) nanocomposites with organo‐modified montmorillonites

Nanocomposites of poly(lactide) (PLA) and the PLA plasticized with diglycerine tetraacetate (PL‐710) and ethylene glycol oligomer containing organo‐modified montmorillonites (ODA‐M and PGS‐M) by the protonated ammonium cations of octadecylamine and poly(ethylene glycol) stearylamine were prepared by melt intercalation method. In the X‐ray diffraction analysis, the PLA/ODA‐M and plasticized PLA/ODA‐M composites showed a clear enlargement of the difference of interlayer spacing between the composite and clay itself, indicating the formation of intercalated nanocomposite. However, a little enlargement of the interlayer spacing was observed for the PLA/PGS‐M and plasticized PLA/PGS‐M composites. From morphological studies using transmission electron microscopy, a finer dispersion of clay was observed for PLA/ODA‐M composite than PLA/PGS‐M composite and all the composites using the plasticized PLA. The PLA and PLA/PL‐710 composites containing ODA‐M showed a higher tensile strength and modulus than the corresponding composites with PGS‐M. The PLA/PL‐710 (10 wt %) composite containing ODA‐M showed considerably higher elongation at break than the pristine plasticized PLA, and had a comparable tensile modulus to pure PLA. The glass transition temperature (T_g) of the composites decreased with increasing plasticizer. The addition of the clays did not cause a significant increase of T_g. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006