Low-temperature sintering of magnesium aluminate spinel doped with manganese: Thermodynamic and kinetic aspects

This work describes the role of manganese (Mn) as a sintering aid for magnesium aluminate (MgAl₂O₄) nanoparticles. Mn-doped MgAl₂O₄ nanoparticles, synthesized by coprecipitation method, showed increased surface area when contrasted to undoped MgAl₂O₄. Fast firing of compacted-doped nanoparticles achieved high degree of densification at temperatures as low as 1100°C with very moderate grain growth, resulting in average sizes at the nanoscale (~60 nm). Differential scanning calorimetry was used to quantify the exothermic heat effects of sintering, which combined with quantitative microstructural evolution analysis enabled calculation of both surface and grain boundary energies. The results revealed that Mn effectively reduces the surface and grain boundary energies which led to dihedral angle broadening and consequently increased sintering stress. Experimental data also revealed a concomitant decrease in the activation energy of sintering with Mn doping which dropped from 644 kJ/mol for undoped MgAl₂O₄ to 285 kJ/mol, informing Mn acts as a sintering aid in a thermokinetic manner.     

Ultra-rapid microwave sintering of pure and Y2O3-doped MgAl2O4

MgAl₂O₄ samples were microwave sintered to near-full density in rapid processes with heating rates on the order of 100°C/min and zero isothermal hold. The experiments were carried out using a gyrotron system for microwave processing of materials operating at a frequency of 24 GHz with a maximum power of 6 kW. In the regimes with a preset heating rate sustained by the automatically regulated microwave power, the maximum achieved density was about 95% of the theoretical value in pristine MgAl₂O₄ samples (maximum sintering temperature 1650°C) and about 97% in 1 wt.% Y₂O₃-doped samples (1700°C). In the regimes with a fixed microwave power (about 3.5 kW), translucent spinel samples with a relative density above 99% were obtained at 1700°C. The duration of the high-temperature stage of sintering was 1.5-10 minutes. The suggested mechanism responsible for the enhanced densification involves development of a thermal instability and formation of transient liquid phases at grain boundaries. The estimated specific absorbed power in the samples during the high-temperature stage of ultra-rapid microwave sintering was 27-80 W/cm³, similar to the values observed in dc field-assisted flash sintering experiments.     

Low cost foam-gelcasting preparation and characterization of porous magnesium aluminate spinel (MgAl2O4) ceramics

Porous MgAl₂O₄ ceramics were prepared via a low cost foam-gelcasting route using MgAl₂O₄ powders as the main raw material, ammonium polyacrylate as a dispersant, a small amount of modified carboxymethyl cellulose as a gelling agent, and TH-IV polymer as a foaming agent. The effects of additive's content, solid loading and gelling temperature on slurry's rheological behavior were investigated, and microstructures and properties of as-prepared porous MgAl₂O₄ ceramics examined. Based on the results, the roles played by the foaming agent in the cases of porosity, pore structure, pore size, mechanical properties and thermal conductivity were clarified. Porosity and pore sizes of as-prepared porous MgAl₂O₄ ceramics increased with increasing the foaming agent from 0.05 to 0.6 vol%. Porous MgAl₂O₄ ceramics with porosity of 75.1% and average pore size of 266 µm exhibited a compressive strength as high as 12.5±0.8 MPa and thermal conductivity as low as 0.24 W/(m K) (at 473 K).     

Liquid‐phase sintering,microstructural evolution,and microwave dielectric properties of Li2Mg3SnO6–LiF ceramics

The liquid‐phase sintering behavior and microstructural evolution of x wt% LiF aided Li₂Mg₃SnO₆ ceramics (x = 1‐7) were investigated for the purpose to prepare dense phase‐pure ceramic samples. The grain and pore morphology, density variation, and phase structures were especially correlated with the subsequent microwave dielectric properties. The experimental results demonstrate a typical liquid‐phase sintering in LiF–Li₂Mg₃SnO₆ ceramics, in which LiF proves to be an effective sintering aid for the Li₂Mg₃SnO₆ ceramic and obviously reduces its optimum sintering temperature from ~1200°C to ~850°C. The actual sample density and microstructure (grain and pores) strongly depended on both the amount of LiF additive and the sintering temperature. Higher sintering temperature tended to cause the formation of closed pores in Li₂Mg₃SnO₆‐x wt% LiF ceramics owing to the increase in the migration ability of grain boundary. An obvious transition of fracture modes from transgranular to intergranular ones was observed approximately at x = 4. A single‐phase dense Li₂Mg₃SnO₆ ceramic could be obtained in the temperature range of 875°C‐1100°C, beyond which the secondary phase Li₄MgSn₂O₇ (<850°C) and Mg₂SnO₄ (>1100°C) appeared. Excellent microwave dielectric properties of Q × f = 230 000‐330 000 GHz, ε_r = ~10.5 and τ_f = ~?40 ppm/°C were obtained for Li₂Mg₃SnO₆ ceramics with x = 2‐5 as sintered at ~1150°C. For LTCC applications, a desirable Q × f value of ~133 000 GHz could be achieved in samples with x = 3‐4 as sintered at 875°C.     

Powder chemistry effects on the sintering of MgO‐doped specialty Al2O3

In this work, we investigate the effects of powder chemistry on the sintering of MgO‐doped specialty alumina. The stages at which MgO influences densification of Al₂O₃ were identified by comparing dilatometry measurements and the sintering kinetics of MgO‐free and MgO‐doped specialty alumina powders. MgO is observed to reduce the grain boundary thickness during densification using TEM. We show that MgO increases the solubility of SiO₂ in alumina grains near the boundaries using EDS. First‐principles DFT calculations demonstrate that the co‐dissolution of MgO and SiO₂ in alumina is thermodynamically favored over the dissolution of MgO or SiO₂ individually in alumina. This study experimentally demonstrates for the first time that removal of SiO₂ from the grain boundaries is a key process by which MgO enhances the sintering of alumina.     

Influence of sintering additives on densification kinetics and high‐temperature strength in γ‐Y2Si2O7 ceramics

Pressureless sintering of pure γ‐Y₂Si₂O₇ powders that had been synthesized by a solid‐liquid reaction method using Y₂O₃ and SiO₂ powders with Li₂O, MgO, and Al₂O₃ additives was reported. The sintering kinetics of γ‐Y₂Si₂O₇ powders was analyzed to track details of densification evolution. Apparent activation energies of the densification of γ‐Y₂Si₂O₇ powders were reported for the first time, which was 57.1, 96.6, and 100.2 kJ/mol for the powders with Li₂O, MgO, and Al₂O₃ additives, respectively, indicating that Li₂O could promote the densification behavior effectively. The flexural strengths as a function of temperature for the γ‐Y₂Si₂O₇ ceramics with different additives were also investigated. The degradation of high‐temperature flexural strength was mainly ascribed to the softening of grain‐boundary glassy phase. γ‐Y₂Si₂O₇ specimens fabricated using the powders with MgO or Al₂O₃ additives exhibited better high‐temperature mechanical properties.     

Demonstration of the cold sintering process study for the densification and grain growth of ZnO ceramics

With the cold sintering process (CSP), it was found that adding acetic acid to an aqueous solution dramatically changed both the densities and the grain microstructures of the ZnO ceramics. Bulk densities >90% theoretical were realized below 100°C, and the average conductivity of CSP samples at around 300°C was similar to samples conventionally sintered at 1400°C. Frequently, ZnO is also used as a model ceramic system for fundamental studies for sintering. By the same procedure as the grain growth of the conventional sintering, the kinetic grain growth exponent of the CSP samples was determined as N=3, and the calculated activated energy of grain growth was 43 kJ/mol, which is much lower than that reported using conventional sintering. The evidence for grain growth under the CSP is important as it indicates that there is a genuine sintering process being activated at these low temperatures and it is beyond a pressurized densification process.     

Mechanical and dielectric properties of porous magnesium aluminate (MgAl2O4) spinel ceramics fabricated by direct foaming-gelcasting

Porous ceramic materials have been broadly applied in various fields due to their multifunctional properties. Optimization of their microstructural characteristics, such as pore morphology, total porosity, and pore size distribution, which determine various properties of the final products, is crucial to improve their performances and thus extend their applications. In this study, single-phase porous MgAl₂O₄ materials were fabricated by direct foaming–gelcasting. With an increase in the foam volume from 260 to 350 mL, the total porosity and pore size of the porous ceramic increased, and its microstructure varied from mostly closed cells to open cells containing interconnected large pores (40–155 μm) and small circular windows (10–40 μm) in the ceramic skeleton. The total porosity could be tailored from 84.91% to 76.08% by modulating the sintering temperature and foam volume and the corresponding compressive strengths were in the range of 2.8–15.0 MPa. The compressive strength exhibited a power-law relationship with the relative density with indices of approximately 3.409 and 3.439, respectively. Porous MgAl₂O₄ ceramics exhibited low dielectric constants in the range of 1.618–1.910 at room temperature, which are well matched with theoretical calculations on account of a modified Bruggeman model. The porous MgAl₂O₄ ceramics with good mechanical and dielectric properties controlled easily by various sintering temperatures and foam volumes are promising for practical applications.     

Gel-casting of transparent magnesium aluminate spinel ceramics fabricated by spark plasma sintering (SPS)

In this paper, a transparent magnesium aluminate spinel ceramic was fabricated through the newest colloidal gel casting method, using a synthetic powder with the average particle size of 90 nm and Isobutylene-Maleic Anhydride (ISOBAM) additive. ISOBAM served as both a dispersant and a gelation agent to achieve a dense body. Also, the suspension rheological behavior was optimized by the solid loading of 85 wt%, the additive content of 0.7 wt%, and the gelation time of 350 s. This led to a green body with a density equal to 65% of theoretical density and the green strength of 14.48 MPa. The results revealed that the reduction of porosity and the uniform distribution of pores in the green body (smaller than half of the initial powder particle size, 35 nm), as accompanied by spark plasma sintering (SPS), resulted in the final body density of 99.97%, as well as the high in-line transmittance of 86.7% at the wavelength of 1100 nm.     

Thermodynamics and kinetics of sintering of Y2O3

Surface energy (γ_S) and grain boundary energy (γ_GB) of yttrium oxide (Y₂O₃) were determined by analyzing the heat of sintering (ΔH_sintering) using differential scanning calorimetry (DSC). The data allowed quantification of sintering driving forces, which when combined with a thorough kinetic analysis of the process, provide better understanding of Y₂O₃ densification as well as insights into effective strategies to improve its sinterability. The quantitative thermodynamic study revealed moderate thermodynamic driving force for densification in Y₂O₃ (as compared to other oxides) represented by a dihedral angle of 152.7° calculated from its surface and grain boundary energies. The activation energy was determined as 307 ± 61 kJ/mol, consistent with activation energies previously reported for processes relevant to sintering of Y₂O_3, such as Y³⁺ diffusion and grain boundary mobility. Finally, we propose that a refined deconvolution study on the DSC curve for Y₂O₃ sintering, combined with the associated material's microstructure evolution, may help identify shifts in sintering mechanisms, and therefore, specific activation energies at increasing temperatures.     

Electrode Effects on Microstructure Formation During FLASH Sintering of Yttrium‐Stabilized Zirconia

Systematic microstructural statistics for 3 mol% yttria‐stabilized zirconia synthesized by both conventional sintering and flash sintering with AC and DC current were obtained. Within the gage section, flash sintered microstructures were indistinguishable from those synthesized by conventional sintering procedures. With both techniques, full densification was obtained. However, from both AC and DC flash sintered specimens, heterogeneous grain size distributions and residual porosity were observed in the proximity of the electrodes. After DC sintering, an almost 400 times increased average grain size was observed near cathode compared to the gage section, unlike areas close to the anode. Concepts of Joule heating alone were not sufficient to explain the experimental observations. Instead, the activation energy for grain growth close to the cathode is lowered considerably during flash sintering, hence suggesting that electrode effects can cause significant heterogeneities in microstructure evolution during flash sintering. Microstructural characterization further indicated that microfracturing during green‐pressing and variations in contact resistance between the electrodes and the ceramic may also contribute to grain size gradients and hence local variations of physical properties.     

Influence of inverse spinel structured CuGa2O4 on microwave dielectric properties of normal spinel ZnGa2O4 ceramics

Spinel Zn_1‐xCu_xGa₂O₄ (x = 0‐0.15) ceramics were prepared by the conventional solid‐state method. Only a single phase was indexed in all samples. The continuous lattice contraction of ZnGa₂O₄ unit cell was caused by Cu²⁺ substitution, and the lattice parameter shows a linear correlation with the content of Cu. The refined crystal structure parameters suggest that Cu²⁺ preferentially occupies the octahedron site, and the degree of inversion of Zn_1‐xCu_xGa₂O₄ (x = 0‐0.15) ceramics almost equals to the content of Cu²⁺. The relative intensity of A*_1g mode in Raman spectra confirm that the degree of inversion climbed with the growing content of Cu²⁺. The experimental and theoretical dielectric constant of Zn_1‐xCu_xGa₂O₄ ceramics fit well. Zn_1‐xCu_xGa₂O₄ (x = 0.01) ceramics sintered at 1400°C for 2 h exhibited good microwave dielectric properties, with ε_r = 9.88, Q × f = 131,445 GHz, tanδ = 6.85 × 10^?5, and τ_f = ?60 ppm/°C.     

Nano-structured MgAl2O4 spinel consolidated by high pressure spark plasma sintering (HPSPS)

Nano-structured transparent polycrystalline magnesium aluminate spinel (PMAS) was fabricated using a high pressure (up to 1000 MPa) spark plasma sintering (HPSPS) apparatus and various properties of the spinel, such as transparency, micro-structure and mechanical properties (specifically, hardness and fracture toughness), were tested. Using a creep densification model, it was concluded that densification in the final stage of HPSPS is controlled by grain boundary sliding (GBS), rather than by oxygen diffusion. The average grain size of PMAS fabricated under 400 MPa pressure at 1200 °C was about 170 nm, while for samples fabricated under 1000 MPa at 1000 °C the average grain size was remarkably smaller (about 50 nm). HRTEM analysis clearly demonstrated clean grain boundaries and triple points with no evidence for the existence of amorphous regions. Fully dense specimens displayed in-line transmittance higher than 80%. It was moreover established that hardness and fracture toughness values did not depend on the indentation load applied. Finally, hardness values for grains sized between tens of microns and tens of nm strictly followed the Hall-Petch relationship.     

Fabrication of high-density NiFe2O4 ceramics by slip casting and pressureless sintering

High-density NiFe₂O₄ ceramics with homogeneous microstructure were produced by slip casting and pressureless sintering. The slurry stability, sintering behavior, and microstructure of NiFe₂O₄ ceramics were investigated. A stable slurry can be obtained by adding 12.5 wt% NiFe₂O₄ nanoparticle and 5 wt% nano-binder at a slurry pH around 11.0. The linear shrinkage and linear shrinkage rate for both NiFe₂O₄ ceramic green bodies shaped by cold press molding and slip casting showed nearly the same trends. The temperature associated with the maximum linear shrinkage rate of slip casted green body was 1263.5°C, which was lower than that of cold press molded sample (1272.0°C). The sintering activation energy of slip casted green body was also lower than that of cold press molded sample (279.18 vs 288.47 kJ mol⁻¹), owing to high density and homogeneity of slip-casted green compact. A high-density NiFe₂O₄ ceramics with uniform grain size distribution can be produced by slip casting and pressureless sintering at 1350°C for 6 hours, attributed to the ability of slip casting to minimize agglomerates and micropores. It demonstrated that slip casting was more suitable to prepare high-density NiFe₂O₄ ceramics with good homogeneity.     

Mechanical properties of 1 mol% CeO2‐10 mol% Sc2O3 co‐doped and stabilized ZrO2 synthesized through hydro/solve‐thermal method

Ultra‐fine 1 mol% CeO₂‐10 mol% Sc₂O₃ co‐doped and stabilized ZrO₂ (1Ce10ScSZ) powders with average grain size less than 10 nm in diameter were prepared by hydro/solve‐thermal method using either deionized water, ethanol, or methanol as solvent. As‐synthesized powders were characterized in terms of phase structure, particle morphology, and chemical composition by X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), high‐resolution transmission electron microscopy (HRTEM), and inductively coupled plasma‐optical emission spectroscopy (ICP‐OES), respectively. Sintering studying was conducted on pellets of 15 mm in diameter and 3 mm in thickness under uniaxial compaction using 25 MPa at either 600, 800, 1000, 1100, 1200, 1400, or 1500°C for 1 hour. Phase transitions and grain morphologies of those sintered samples were characterized by XRD and field emission scanning electron microscopy (FESEM). Mechanical properties were characterized on dense pellets sintered at 1500°C by nanoindentation. Experimental results showed that ethanol was more effective to synthesize agglomerate‐free 1Ce10ScSZ powders as compared with deionized water and methanol. Choice of solvent affected the environment of hydro/solve‐thermal solution, which led to variation of chemical compositions of powders and porosities of sintered pellets, and therefore, influenced their mechanical performance. Our study showed that solvent was important to make dense, thin, and mechanically robust 1Ce10ScSZ electrolyte for potential applications in electrochemical devices. Absolute values of hardness (H) and Young's modulus (E) measured from our samples are much higher and more consistence than those results obtained from commercial vendors reported in literatures.     

Sintering behavior of magnesium aluminate spinel MgAl2O4 synthesized by different methods

This paper is focusing basically on the ceramic technology, of which several methods for the synthesis of MgAl₂O₄ have been investigated. The synthesis conditions regarding the powders cleanliness, microstructure, and sintering parameters of MgAl₂O₄ were studied. MgAl₂O₄ powder was synthesized via conventional solid-state route using different milling process: vertical attrition milling, WAB as a high-energy horizontal attrition milling, and Pulverisette as a planetary ball miller, and via solution combustion route using Urea, Glycine, and a mixture of Urea/Glycine. Urea and Glycine was used as fuel. The white powders were obtained for all solid-state routes and for Urea-combustion technique. The black and gray powders were obtained in the case of combustion technique, respectively, using a fuel of Glycine and Glycine/Urea mixture. The obtained powders and pellets were characterized by XRD, SEM, and Dilatometry. The results show that, among all the solid-state route processes, wet attrition milling gives the better and clean spinel phase. The WAB milling and Pulverisette miller introduce a contamination by some yttria-stabilized zirconia balls in the corresponding powder. Furthermore, the flash combustion technique permit to have nanoparticles with a dense spinel phase of MgAl₂O₄ and with lower sintering temperature in less time and with no calcination step.     

Low‐temperature sintering and enhanced piezoelectric properties of random and textured PIN–PMN–PT ceramics with Li2CO3

Low‐temperature sintered random and textured 36PIN–30PMN–34PT piezoelectric ceramics were successfully synthesized at a temperature as low as 950°C using Li₂CO₃ as sintering aids. The effects of Li₂CO₃ addition on microstructure, dielectric, ferroelectric, and piezoelectric properties in 36PIN–30PMN–34PT ternary system were systematically investigated. The results showed that the grain size of the specimens increased with the addition of sintering aids. The optimum properties for the random samples were obtained at 0.5 wt% Li₂CO₃ addition, with piezoelectric constant d₃₃ of 450 pC/N, planar electromechanical coupling coefficient k_p of 49%, peak permittivity ε_max of 25 612, remanent polarization P_r of 36.3 μC/cm². Moreover, the low‐temperature‐sintered textured samples at 0.5 wt% Li₂CO₃ addition exhibited a higher piezoelectric constant d₃₃ of 560 pC/N. These results indicated that the low‐temperature‐sintered 36PIN–30PMN–34PT piezoelectric ceramics were very promising candidates for the multilayer piezoelectric applications.     

Preparation and characterization of magnesium aluminate (MgAl2O4) spinel ceramic foams via direct foam-gelcasting

Lightweight MgAl₂O₄ spinel ceramic foams with high mechanical strength and good dielectric properties were prepared with a direct foam-gelcasting method using MgAl₂O₄ and TiO₂ (rutile phase, as sintering aid) powders. The effects of calcination temperature and foam volume on bulk density, apparent porosity, and on the mechanical and dielectric properties of the ceramic foams were investigated. Tailored porosity (75.14–82.46%), pore size (10–200 μm), dielectric constant (1.66–2.05), and compressive strength (4.0–14.3 MPa), were obtained based on the change of the foam volume in the foamed slurries, and the calcination temperature of porous ceramics. The compressive strength and dielectric constant of the as-manufactured spinel foam with a porosity of ~75.14% was as high as 14.3 MPa and 2.05, respectively. The spinel ceramic foam which had a porosity of 81.84% was prepared with a foam volume of 350 mL and a sintering temperature of 1500 °C, and exhibited heterogeneous pore structures, whereby large and open spherical cells involved in small circular windows on the internal walls with a mean pore size of ~66.26 μm and a grain size of ~8 μm. The experimental dielectric constant matches well with that calculated by the modified Bruggeman model. The dependence of the mechanical strength on the relative density can be represented by the Gibson and Ashby model. The fitted index values of the power relationship were 3.504 and 3.533, compared to the theoretical value of 1.5. The ceramic foam can potentially become a new type of electromagnetic wave-transmitting radome material due to its low dielectric constant (1.66–2.05) and dielectric loss (0.0026–0.006) values.     

The Effects of Na2O and SiO2 on Liquid Phase Sintering of Bayer Al2O3

To determine how grain‐boundary composition affects the liquid phase sintering of MgO‐free Bayer process aluminas, samples were singly or co‐doped with up to 1029 ppm Na₂O and 603 ppm SiO₂ and heated at 1525°C up to 8 h. Na₂O retards densification of samples from the onset of sintering and up to hold times of 30 min at 1525°C compared to the undoped samples, but similar to the as‐received, MgO‐free Al₂O₃, Na₂O‐doped samples sinter to 98% density with average grain sizes of ~3 μm after 8 h. Increasing SiO₂ concentration significantly retards densification at all hold times up to 8 h. The estimated viscosities (20?400 Pa·s) of the 0.3 to 1.8 nm thick siliceous grain‐boundary films in this study indicate that diffusion greatly depends on the composition of the liquid grain‐boundary phase. For low Na₂O/SiO₂ ratios, densification of Bayer Al₂O₃ at 1525°C is controlled by diffusion of Al³⁺ through the grain‐boundary liquid, whereas for high Na₂O/SiO₂ ratios, densification can be governed by either the interface reaction (i.e., dissolution) of Al₂O₃ or diffusion of Al³⁺. Increasing Na₂O in SiO₂‐doped samples increases diffusion of Al³⁺ and Al₂O₃ solubility in the liquid, and thus densification increases by 1%. Based on these findings, we conclude that Bayer Al₂O₃ densification can be manipulated by adjusting the Na₂O to SiO₂ ratio.     

Pressure-enhanced densification of TaC ceramics during flash spark plasma sintering

Flash spark plasma sintering (FSPS) offers extremely high heating rates to consolidate ceramics at a short time. However, significant grain growth sometimes occurs accompanied by rapid densification. In this work, a FSPS apparatus available for applying pressure was used to sinter TaC ceramics from powder compacts without preheating. It is found that the use of a higher pressure can efficiently promote densification and retard significant grain growth. Dense bulk TaC ceramics (95.18%) with average grain size of 4.09 μm were obtained in 90 seconds under 80 MPa. Such a process should facilitate the fast preparation of refractory ceramics with fine-grained microstructure.