Composition‐ and Temperature‐Dependent Large Strain in (1−x)(0.8Bi0.5Na0.5TiO3–0.2Bi0.5K0.5TiO3)– xNaNbO3 Ceramics

Ternary solid solutions of (1 ? x)(0.8Bi_0.5Na_0.5TiO₃–0.2Bi_0.5K_0.5TiO₃)– xNaNbO₃ (BNKT–xNN) lead‐free piezoceramics were fabricated using a conventional solid‐state reaction method. Pure BNKT composition exhibited an electric‐field‐induced irreversible structural transition from pseudocubic to ferroelectric rhombohedral phase at room temperature. Accompanied with the ferroelectric‐to‐relaxor temperature T_F‐R shifted down below room temperature as the substitution of NN, a compositionally induced nonergodic‐to‐ergodic relaxor transition was presented, which featured the pinched‐shape polarization and sprout‐shape strain hysteresis loops. A strain value of ~0.445% (under a driving field of 55 kV/cm) with large normalized strain of ~810 pm/V was obtained for the composition of BNKT–0.04NN, and the large strain was attributed to the reversible electric‐field‐induced transition between ergodic relaxor and ferroelectric phase.     

Temperature‐insensitive strain behavior in 0.99[(1−x)Bi0.5(Na0.80K0.20)0.5TiO3−xBiFeO3]–0.01Ta lead‐free piezoelectric ceramics

Lead‐free 0.99[(1?x)Bi_0.5(Na_0.80K_0.20)_0.5TiO₃?xBiFeO₃]–0.01Ta (BNKT20–100xBF–1Ta) lead‐free piezoelectric ceramics were fabricated through conventional solid state sintering method. Results showed that change of BF content in the BNKT20–100xBF–1Ta induced a phase transition from ferroelectric to ergodic relaxor phase with a significant disruption of the long‐range ferroelectric order. A large electric‐field‐induced strain of 0.36% (at 80 kV/cm driving field, corresponding to a large signal of ~450 pm/V) which is derived from a reversible field‐induced ergodic relaxor to ferroelectric phase transformation, was obtained in the composition with x=0.01 near the ferroelectric‐ergodic relaxor phase boundary. Moreover, an attractive property for application in nonlinear actuators demanding enhanced thermal stability was obtained in this material, which showed a temperature‐insensitive strain characteristic in the temperature range from room temperature to 100°C.     

Large Strain Response and Fatigue‐Resistant Behavior in Ternary Bi0.5Na0.5TiO3–BaTiO3–Bi(Zn0.5Ti0.5)O3 Solid Solutions

A ternary solid solution (1 ? x)(0.88Bi_0.5Na_0.5TiO₃–0.12BaTiO₃)‐xBi(Zn_0.5Ti_0.5)O₃ (BNBZT, BNBZTx) was designed and fabricated using the traditional solid‐state reaction method. The temperature and composition dependence of dielectric, ferroelectric, piezoelectric, and fatigue properties were systematically investigated and a schematic phase diagram was proposed. The substitution with Bi(Zn_0.5Ti_0.5)O₃ was found to shift the phase transition (ferroelectric tetragonal to relaxor pseudocubic phase) to lower temperatures. At a critical composition x of 0.05, large electric‐field‐induced strain response with normalized strain S_max/E_max as high as 526 pm/V was obtained under a moderate field of 4 kV/mm around room temperature. The strain exhibited good temperature stability within the temperature range of 25°C–120°C. In addition, excellent fatigue‐resistant behavior was observed in the proposed BNBZT solid solution after 10⁶ bipolar cycles. These give the BNBZT system great potential as environmental friendly solid‐state actuator.     

Dielectric Relaxor Evolution and Frequency‐Insensitive Giant Strains in (Bi0.5Na0.5)TiO3‐Modified Bi(Mg0.5Ti0.5)O3–PbTiO3 Ferroelectric Ceramics

The 0.45Bi(Mg_0.5Ti_0.5)O₃–(0.55 ? x)PbTiO₃–x(Bi_0.5Na_0.5)TiO₃ (BMT–PT–xBNT) ternary solid solution ceramics were prepared via a conventional solid‐state reaction method; the evolution of dielectric relaxor behavior and the electrostrain features were investigated. The XRD and dielectric measurements showed that all studied compositions own a single pseudocubic perovskite structure and undergo a diffuse‐to‐relaxor phase transition owing to the evolution of the domain from a frozen state to a dynamic state. The formation of the above dielectric relaxor behavior was further confirmed by a couple of measurements such as polarization loops, polarization current density curves, as well as bipolar strain loops. A large strain value of ~0.41% at a driving field of 7 kV/mm (normalized strain d₃₃* of ~590 pm/V) was obtained at room temperature for the composition with x = 0.32, which is located near the boundary between ergodic and nonergodic relaxor. Moreover, this electric field‐induced large strain was found to own a frequency‐insensitive characteristic.     

Temperature‐Insensitive High Strain in Lead‐Free Bi0.5(Na0.84K0.16)0.5TiO3–0.04SrTiO3 Ceramics for Actuator Applications

Lead‐free piezoelectric ceramics, 0.96[{Bi_0.5 (Na_0.84K_0.16)_0.5}_1?xLi_x(Ti_1?yNb_y)O₃]–0.04SrTiO₃ (BNKLiTN–ST) with x, y = 0–0.030, were synthesized by solid‐state reaction method. X‐ray diffraction patterns indicated that Li and Nb successfully diffused into the BNKT–ST lattice and formed a pure perovskite structure with x, y ≤ 0.025. Increasing the Li and Nb contents (x, y = 0.020) induced a phase transformation from the coexistent rhombohedral–tetragonal phases for pure BNKT–ST ceramics to a pseudocubic phase, resulting in degradation of the remnant polarization and coercive field. However, the field‐induced strain was markedly enhanced at x, y = 0.020, giving rise to a giant dynamic piezoelectric constant (d₃₃* = S_max/E_max = 800 pm/V). Furthermore, the temperature dependence of the field‐induced strain response showed temperature‐insensitivity up to 120°C. To explore its potential for device applications, a 10‐layered stack‐type multilayer actuator was fabricated from the optimal composition (x, y = 0.020). This actuator showed a large S_max/E_max of 600 pm/V at a relatively low driving field of 4.5 kV/mm suggesting highly promising results in lead‐free BNT‐based ceramics.     

The Relationship Between Phase Structure and Electrical Properties in (1 − x)(Bi0.5Na0.5TiO3–Ba0.5K0.5TiO3–BaTiO3)‐ xK0.5Na0.5NbO3 Quaternary Lead‐Free Piezoelectric Ceramics

(1 ? x)(0.85Bi_0.5Na_0.5TiO₃–0.11Ba_0.5K_0.5TiO₃–0.04BaTiO₃)‐ xK_0.5Na_0.5NbO₃ lead‐free piezoelectric ceramics with x = 0.00, 0.02, 0.03, 0.04, 0.05, and 0.10 were prepared by a conventional solid state method. A coexistence of rhombohedral (R) and tetragonal (T) phases was found in the system, which tended to evolve into pseudocubic symmetry when x increases. The x = 0.04 sample exhibited improved electrical properties: the dielectric constant ε_r = 1900 with the low loss tangents 0.06, the S_max/E_max of ~400 and ~460 pm/V under unipolar and bipolar electric field, respectively. Meanwhile, piezoelectric constant d₃₃ still maintained ~160 pC/N. These could be owed to the formation of polar nanoregions for relaxor phase.     

Preparation and Electric Properties of Bi0.5Na0.5TiO3–Bi(Al0.5Ga0.5)O3 Lead‐Free Piezoceramics

A new lead‐free BNT‐based piezoelectric ceramics of (1 ? x)Bi_0.5Na_0.5TiO₃–xBi(Al_0.5Ga_0.5)O₃ (x = 0, 0.02, 0.03, 0.04, and 0.05) were synthesized using a conventional ceramic fabrication method. Their structures and electrical properties were investigated. All the samples show a typical ferroelectric P(E) loops and S(E) curves at room temperature. The optimal properties are obtained at the composition of the x = 0.03. The substitution of Bi(Al_0.5Ga_0.5)O₃ enhances piezoelectric constant and increases Curie temperature from 58 pC/N and 310°C of pure BNT to 93 pC/N and 325°C of the x = 0.03. The temperature‐dependent P(E) loops and S(E) curves of 0.97BNT–0.03BAG indicate that phase transition from ferroelectric to antiferroelectric takes place over a very wide temperature region from 80°C to 180°C. The results show that the introduction of BAG improves the electrical properties of BNT.     

Large Electrostrictive Strain in (Bi0.5Na0.5)TiO3–BaTiO3–(Sr0.7Bi0.2)TiO3 Solid Solutions

Relaxor ferroelectrics (0.94 ? x)(Bi_0.5Na_0.5)TiO₃–0.06BaTiO_3?x(Sr_0.7Bi_0.2□_0.1)TiO₃ (BNT–BT–xSBT) (0 ≤ x ≤ 0.5), were prepared by a solid‐state reaction process, and their structures were characterized by the transmission electron microscopy and Raman spectroscopy. The BNT–BT–0.3SBT has a very high electrostrictive strain S = 0.152% with hysteresis‐free behavior, much more than the reported S in other ferroelectrics. S–P² profiles perfectly follow the quadratic relation, which indicates a purely electrostrictive effect with a high electrostrictive coefficient (Q₁₁) of 0.0297 m⁴/C². Even, its Q₁₁ keeps at a high level in the temperature range from ambient temperature to 180°C. The field‐induced large electrostrictive strain of BNT–BT–0.3SBT was attributed to the existence of ferroelectric nanodomains.     

Photoluminescence and Temperature Dependent Electrical Properties of Er‐Doped 0.94Bi0.5Na0.5TiO3‐0.06BaTiO3 Ceramics

Er‐doped 0.94Bi_0.5Na_0.5TiO₃‐0.06BaTiO₃ (BNT‐6BT: xEr, x is the molar ratio of Er³⁺ doping) lead‐free piezoceramics with x = 0–0.02 were prepared and their multifunctional properties have been comprehensively investigated. Our results show that Er‐doping has significant effects on morphology of grain, photoluminescence, dielectric, and ferroelectric properties of the ceramics. At room temperature, the green (550 nm) and red (670 nm) emissions are enhanced by Er‐doping, reaching the strongest emission intensity when x = 0.0075. The complex and composition‐dependent effects of electric poling on photoluminescence also have been measured. As for electrical properties, on the one hand, Er‐doping tends to flatten the dielectric constant‐temperature (ε_r‐T) curves, leading to temperature‐insensitive dielectric constant in a wide temperature range (50°C–300°C). On the other hand, Er‐doping significantly decreases the ferroelectric‐relaxor transition temperature (T_F–R) and depolarization temperature (T_d), with the T_F–R decreasing from 76°C to 42°C for x = 0–0.02. As a result, significant composition‐dependent electrical features were found in ferroelectric and piezoelectric properties at room temperature. In general, piezoelectric and ferroelectric properties tend to become weaker, as confirmed by the composition‐dependent piezoelectric coefficient (d₃₃), planar coupling factor (k_p), and the shape of polarization‐electric field (P–E), current‐electric field (J–E), bipolar/unipolar strain‐electric field (S–E) curves. Furthermore, to understand the relationship between the T_F–R/T_d and the electrical properties, the composition of x = 0.0075 has been intensively studied. Our results indicate that the BNT‐6BT: xEr with appropriate Er‐doping may be a promising multifunctional material with integrated photoluminescence and electrical properties for practical applications.     

Stress driven high electrostrain at low field in incipient piezoelectrics

We use a strategy to reduce the driving electric field of the relaxor 0.72Bi_1/2Na_1/2TiO₃–0.28SrTiO₃ (BNT–28ST) by introducing ferroelectric plate–type Bi_1/2(Na_0.78K_0.22)_1/2TiO₃ (BNKT) particles. Consequently, 10 vol.% BNKT added BNT–28ST/BNKT (relaxor/ferroelectric) composite has delivered large normalized strain (S_max/E_max = 650 pm/V) under relatively low applied field of 2.5 kV/mm with the reduction in the poling field value to 36% compared to that of pure BNT–28ST ceramics. We demonstrated that such behavior comes from the stress induced effect at the boundary of the ferroelectric and relaxor materials due to their different nature (relaxor/ferroelectric). The generation of stress is expected from the ferroelectric (BNKT) to the relaxor (BNT–28ST) at the boundary. Thereby, field–dependent stress at relaxor/ferroelectric phase boundary is monitored proposing the reduction of the poling field due to the strain coupling mechanism. Our findings provide a pathway for reducing the poling field in BNT–based incipient piezoelectric ceramics.     

A Novel BiFeO3–BaTiO3–BaZrO3 Lead‐Free Relaxor Ferroelectric Ceramic with Low‐Hysteresis and Frequency‐Insensitive Large Strains

A novel (0.67?x)BiFeO₃–0.33BaTiO₃–xBaZrO₃ lead‐free relaxor ferroelectric ceramic was developed by a solid‐state reaction method. Measurements of temperature‐dependent dielectric permittivity and the polarization/strain hysteresis loops demonstrated an obvious evolution of dielectric relaxor behavior at room temperature (RT) from nonergodic to ergodic states. A significantly enhanced electrostrain of ~0.37% at 7 kV/mm with a relatively small hysteresis of ~39% and a low‐frequency sensitivity was found at x = 0.04, showing large potential for actuator applications. This was basically attributed to a rapid response of forward and backward switching between ergodic and ferroelectric phases owing to similar free energies and large local random fields.     

Large Strain Response in 0.99(Bi0.5Na0.4K0.1)TiO3–0.01(KxNa1−x)NbO3 Lead‐Free Ceramics Induced by the Change of K/Na Ratio in (KxNa1−x)NbO3

Influence of K/Na ratio in (K_xNa_1?x)NbO₃ on the ferroelectric stability and consequent changes in the electrical properties of 0.99(Bi_0.5Na_0.4K_0.1)TiO₃–0.01(K_xNa_1?x)NbO₃ (BNKT–K_xNN) ceramics were investigated. Results showed that change of K/Na ratio in KNN induces a phase transition from ferroelectric to ergodic relaxor phase with a significant disruption of the long‐range ferroelectric order, and correspondingly adjusts the ferroelectric–relaxor transition point T_F?R to room temperature. Accordingly, giant strain of ~0.46% (corresponding to a large signal d₃₃* of ~575 pm/V) which is comparable to that of Pb‐based antiferroelectrics is obtained at a K/Na ratio of ~1, and the emergence of large strain response induced by the change of K/Na ratio of KNN can be well explained by the correlation between the position of ferroelectric–ergodic relaxor phase boundary in the BNKT–K_xNN system and the tolerance factor t of the end number (K_xNN). In situ high‐energy X‐ray scattering experiments with external field reveals that the large strain response in the studied system is likely related to the electric field‐induced distortion from the pseudocubic structure.     

Preparation and Electric Properties of Bi0.5Na0.5TiO3–Bi(Mg0.5Ti0.5)O3 Lead‐Free Piezoceramics

Lead‐free BNT‐based piezoceramics, (1?x)Bi_0.5Na_0.5TiO₃–xBi(Mg_0.5Ti_0.5)O₃ [(1?x)BNT–xBMT] (0.00 ≤ x ≤ 0.06) binary system, were synthesized using a conventional ceramic fabrication method. Effect of Bi(Mg_0.5Ti_0.5)O₃ (BMT) substitution on room temperature (RT) crystal structure, and temperature dependence of electric properties were investigated. The XRD indicates that a pure perovskite phase is formed. The introduction of BMT decreases E_C of BNT from 7.3 to 4.0 kV/mm, and increases d₃₃ from 58 pC/N to 110 pC/N for the x = 0.05. The system shows a typical ferroelectric (FE) polarization loop P(E) and butterfly bipolar strain‐electric S(E) curve at RT. For the composition of 0.95BNT–0.05BMT antiferroelectric (AFE) phase appears near 80°C, characterized by a constricted P(E) loop and altered bipolar S(E) butterfly, and gradually prevails with increasing temperature. Temperature dependence of dielectric constant shows that T_C increases from 310°C for pure BNT to 352°C for the x = 0.05. The results indicate that the piezoelectric properties of BNT have been improved by means of Bi(Mg_0.5Ti_0.5)O₃ substitution.     

Phase‐Composition‐Dependent Piezoelectric and Electromechanical Strain Properties in (Bi1/2Na1/2)TiO3–Ba(Ni1/2Nb1/2)O3 Lead‐Free Ceramics

New lead‐free perovskite solid solution ceramics of (1 ? x)(Bi_1/2Na_1/2)TiO₃–xBa(Ni_1/2Nb_1/2)O₃[(1?x)BNT–xBNN,x = 0.02–0.06) were prepared and their dielectric, ferroelectric, piezoelectric, and electromechanical properties were investigated as a function of the BNN content. The X‐ray diffraction results indicated that the addition of BNN has induced a morphotropic phase transformation from rhombohedral to pseudocubic symmetry approximately at x = 0.045, accompanying an evolution of dielectric relaxor behavior as characterized by enhanced dielectric diffuseness and frequency dispersion. In the proximity of the ferroelectric rhombohedral and pseudocubic phase coexistence zone, the x = 0.045 ceramics exhibited optimal piezoelectric and electromechanical coupling properties of d₃₃~121 pC/N and k_p~0.27 owing to decreased energy barriers for polarization switching. However, further addition of BNN could cause a decrease in freezing temperatures of polar nanoregions till the coexistence of nonergodic and ergodic relaxor phases occurred near room temperature, especially for the x = 0.05 sample which has negligible negative strains and thus show the maximum electrostrain of 0.3% under an external electric field of 7 kV/mm, but almost vanished piezoelectric properties. This was attributed to the fact that the induced long‐range ferroelectric order could reversibly switch back to its original ergodic state upon removal of external electric fields.     

Ferroelectric‐quasiferroelectric‐ergodic relaxor transition and multifunctional electrical properties in Bi0.5Na0.5TiO3‐based ceramics

A‐site substituted 0.88(Bi_0.5Na_0.5)_1?x(Li_0.5Nd_0.5)_xTiO₃–0.12BaTiO₃ (BNTLNx–BT12) ceramics were synthesized using a conventional solid‐state reaction route. The structural transformation and miscellaneous electrical properties were systematically investigated. The A‐site modification induced two sequence transitions from ferroelectric tetragonal (T) to quasi‐ferroelectric pseudocubic (PC) phase, followed closely by the second transition from non‐ergodic to ergodic relaxor (NR‐ER), and finally to dynamic polar nanoregions (PNRs). The significant enhancement in piezoelectric activity, strain response, broad plateau‐like maximum dielectric permittivity over a large temperature range and energy‐storage level at different compositions may be attributed to the compositionally‐induced T‐PC to NR‐ER transition and the alignment of dynamically‐fluctuating PNRs, respectively. The evolution of multifunctional electrical properties, associated with the variations in structure/microstructure, might provide a new insight to investigate the underlying mechanism of structure‐electrical properties relationship in ferroelectric solid solutions.     

Novel BiFeO3–BaTiO3–Ba(Mg1/3Nb2/3)O3 Lead‐Free Relaxor Ferroelectric Ceramics for Energy‐Storage Capacitors

A novel lead‐free relaxor ferroelectric ceramic of (0.67?x)BiFeO₃–0.33BaTiO₃–xBa(Mg_1/3Nb_2/3)O₃ [(0.67?x)BF–0.33BT–xBMN, x = 0–0.1] was prepared by a solid‐state reaction method. A relatively high maximum polarization P_max of 38 μC/cm² and a low remanent polarization P_r of 5.7 μC/cm² were attained under 12.5 kV/mm in the x = 0.06 sample, leading to an excellent energy‐storage density of W ~1.56 J/cm³ and a moderate energy‐storage efficiency of η ~75%. Moreover, a good temperature stability of the energy storage was obtained in the x = 0.06 sample from 25°C to 190°C. The achievement of these characteristics was basically attributed to an electric field induced reversible ergodic to ferroelectric phase transition owing to similar free energies near a critical freezing temperature. The results indicate that the (0.67?x)BF–0.33BT–xBMN lead‐free realxor ferroelectric ceramic could be a promising dielectric material for energy‐storage capacitors.     

Ultra‐Wide Temperature Stable Dielectrics Based on Bi0.5Na0.5TiO3–NaNbO3 System

The microstructure, phase structure, ferroelectric, and dielectric properties of (1?x)Bi_0.5Na_0.5TiO₃‐xNaNbO₃ [(1?x)BNT‐xNN] ceramics conventionally sintered in the temperature range of 1080°C–1120°C were investigated as a candidate for capacitor dielectrics with wide temperature stability. Perovskite phase with no secondary impurity was observed by XRD measurement. With increasing NN content, (1?x)BNT‐xNN was found to gradually transform from ferroelectric (x = 0–0.05) to relaxor (x = 0.10–0.20) and then to paraelectric state (x = 0.25–0.35) at room temperature, indicated by P–I–E loops analysis, associated with greatly enhanced dielectric temperature stability. For the samples with x = 0.25–0.35, the temperature coefficient of capacitance (TCC) was found <11% in an ultra‐wide temperature range of ?60°C–400°C with moderate dielectric constant and low dielectric loss, promising for temperature stable capacitor applications.     

The electrical properties of (1−x)(Bi0.5Na0.5TiO3–Bi0.5K0.5TiO3–BaTiO3)–xCaZrO3 lead-free piezoelectric ceramics

Lead-free (1−x)(0.0852Bi_0.5Na_0.5TiO₃–0.12Bi_0.5K_0.5TiO₃–0.028BaTiO₃)–xCaZrO₃ piezoelectric ceramics (BNT−BKT−BT−xCZ, x=0, 0.01, 0.02, 0.03, 0.04 and 0.05) were prepared by using a conventional solid-state reaction method. The effects of CZ-doping on the structural, dielectric, ferroelectric and piezoelectric properties of the BNT−BKT−BT−xCZ system were systematically investigated. The polarization and strain behaviors indicated that the long-range ferroelectric order in the unmodified BNT−BKT−BT ceramics was disrupted by the increase of CZ-doping content, and correspondingly the depolarization temperature (T_d) shifted down from 109 °C to below room temperature. When x>0.03, accompanied with the drastic decrease in the remnant polarization (P_r) and piezoelectric coefficient (d₃₃), the electric-field-induced strain was enhanced significantly. A large unipolar strain of 0.35% under an applied electric field of 70 kV/cm (S_max/E_max=500 pm/V) was obtained in the BNT−BKT−BT−0.04CZ ceramics at room temperature, which was attributed to the reversible electric-field-induced phase transition between the relaxor and ferroelectric phases.     

The Composition and Temperature‐Dependent Structure Evolution and Large Strain Response in (1−x)(Bi0.5Na0.5)TiO3−xBa(Al0.5Ta0.5)O3 Ceramics

The (1?x) (Bi_0.5Na_0.5)TiO₃?xBa(Al_0.5Ta_0.5)O₃((1?x)BNT‐xBAT) lead‐free piezoceramics was fabricated using a conventional solid‐state reaction method. The temperature and composition‐dependent strain behavior, dielectric, ferroelectric (FE), piezoelectric, and pyroelectric properties have been systematically investigated to develop lead‐free piezoelectric materials with large strain response for actuator application. As the BAT content increased, the FE order is disrupted resulting in a degradation of the remanent polarization, coercive field, and the depolarization temperature (T_d). A large strain of 0.36% with normalized strain d₃₃* = 448pm/V was obtained for the optimum composition x = 0.045 at room temperature. The bipolar and unipolar strains for the compositions x = 0.035 and x = 0.04 reach almost identical maximum values when the temperature is in the vicinity of their respective depolarization temperature (T_d). The Raman‐spectra analysis, macroscopic properties, thermal depolarization results, and temperature‐dependent relationships of both polarization and strain demonstrated that the origin of the large strain response for this investigated system is attributed to a field‐induced relaxor to FE phase transformation.     

Lead‐Free (Ba0.70Sr0.30)TiO3‐Modified Bi0.5(Na0.80K0.20)0.5TiO3 Ceramics with Large Electric Field–Induced Strains

The dielectric, ferroelectric, and electric field–induced strain behavior of Bi_0.5(Na_0.80K_0.20)_0.5TiO₃ (BNKT) ceramics modified with (Ba_0.70Sr_0.30)O₃ (BST) were investigated as a function of composition and temperature. The ceramic samples were synthesized by a solid‐state mixed oxide method and sintered at 1125°C for 2 h. The XRD and Raman spectra showed coexisting rhombohedral and tetragonal phases throughout the entire compositional range with the tetragonal phase becoming dominant at higher BST concentrations. For all compositions, the temperature dependence of the dielectric spectra revealed a frequency dependence that is characteristic of a relaxor mechanism. This suggests that these ceramics lacked long‐range order and it appears that the maximum disorder was observed for the composition with 5 mol% BST (BNKT–0.05BST sample). This was evidenced by the observation of pinched hysteresis loops, even at room temperature, and a significant decrease in the P_r and E_c values which resulted in large electric field–induced strains (S_max) of 0.40% and a normalized strain coefficient ( = S_max/E_max) of 732 pm/V. This significant strain enhancement at the composition of x = 0.05 may be attributed to both a composition‐induced structural phase transition and a field‐induced relaxor to ferroelectric phase transition.