Fabrication and characteristic of non-oxide fiber tow reinforced silicon nitride matrix composites by low temperature CVI process

Non-oxide fiber tow reinforced silicon nitride matrix composite was fabricated by low temperature CVI process with PyC as interphase. The tensile strength of the C and SiC fiber tow composites were 547 MPa and 740 MPa, respectively. The difference in tensile strength was analyzed based on the length, amount of pull-out fiber and also interface bonding. The infiltration uniformity of CVI silicon nitride (SiN) matrix within SiC fiber tow was comparable with that of CVI SiC matrix. These results suggested that the low temperature CVI process is suitable for the fabrication of fiber reinforced SiN matrix composites with proper interface bonding and high strength.     

Low density,three-dimensionally interconnected carbon nanotube/silicon carbide nanocomposites for thermal protection applications

Synthesis of silicon carbide (SiC) nanostructures and their composites has been a topic of interest for the scientific community due to the unique properties that can be obtained with nanoscale features. Herein, we report the scalable fabrication of anisotropic and low density, carbon nanotube/SiC (CNT/SiC) core-shell structures synthesized via chemical vapor infiltration (CVI) of silicon on aligned CNT foams followed by heat treatment at 1350 °C. Structures made of CNT/SiC nanotube networks with a thickness of 1 cm and length of 9 cm were prepared in the present work. Upon the removal of the CNT foam via calcination of the hybrid nanocomposite in air, a free-standing mechanically robust three-dimensional network of pure SiC nanotubes was left behind. The density of the synthesized CNT/SiC is the lowest reported for any C/SiC structure. Furthermore, the CNT/SiC hybrid nano-architecture demonstrated superb heat resistance and stability in ultrahigh temperature environment.     

Fatigue of three advanced SiC/SiC ceramic matrix composites at 1200°C in air and in steam

High‐temperature mechanical properties and tension‐tension fatigue behavior of three advanced SiC/SiC composites are discussed. The effects of steam on high‐temperature fatigue performance of the ceramic‐matrix composites are evaluated. The three composites consist of a SiC matrix reinforced with laminated, woven SiC (Hi‐Nicalon?) fibers. Composite 1 was processed by chemical vapor infiltration (CVI) of SiC into the Hi‐Nicalon? fiber preforms coated with boron nitride (BN) fiber coating. Composite 2 had an oxidation inhibited matrix consisting of alternating layers of silicon carbide and boron carbide and was also processed by CVI. Fiber preforms had pyrolytic carbon fiber coating with boron carbon overlay applied. Composite 3 had a melt‐infiltrated (MI) matrix consolidated by combining CVI‐SiC with SiC particulate slurry and molten silicon infiltration. Fiber preforms had a CVI BN fiber coating applied. Tensile stress‐strain behavior of the three composites was investigated and the tensile properties measured at 1200°C. Tension‐tension fatigue behavior was studied for fatigue stresses ranging from 80 to 160 MPa in air and from 60 to 140 MPa in steam. Fatigue run‐out was defined as 2 × 10⁵ cycles. Presence of steam significantly degraded the fatigue performance of the CVI SiC/SiC composite 1 and of the MI SiC/SiC composite 3, but had little influence on the fatigue performance of the SiC/SiC composite 2 with the oxidation inhibited matrix. The retained tensile properties of all specimens that achieved fatigue run‐out were characterized. Composite microstructure, as well as damage and failure mechanisms were investigated.     

Microstructure and properties of needle punching chopped carbon fiber reinforced carbon and silicon carbide dual matrix composite

Chopped carbon fiber preform reinforced carbon and SiC dual matrix composites (C/C–SiC) were fabricated by chemical vapor infiltration (CVI) combined with liquid silicon infiltration. The preform was fabricated by repeatedly overlapping chopped carbon fiber web and needle punching technique. A geometry model of the pore structure of the preform was built and reactant gas transportation during the CVI was calculated. The microstructure and properties of the C/C–SiC composites were investigated. The results indicated that the CVI time for densification of the preform decrease sharply, and the model showed the permeability of the preform decreased with the increase of its density. The C/C–SiC exhibited good mechanical characteristics, especially excellent compressive behavior, with the vertical and parallel compressive strength reached to 359(±40) MPa and 257(±35) MPa, respectively. The coefficient of friction (COF) decreased from 0.60 (at 8 m/s) with the increase of sliding velocity, and finally stabilized at ~0.35 under the velocity of 20 m/s and 24 m/s, and the variations of COF were not sensitive to the sliding distance. The wear rates were between 0.012 cm³/MJ and 0.024 cm³/MJ under different velocities. These results showed that the chopped carbon fiber preform reinforced C/C–SiC are promising candidates for high-performance and low-cost friction composites.     

Effects of channel modification on microstructure and mechanical properties of C/SiC composites prepared by LA-CVI process

Carbon fiber reinforced SiC matrix composites (C/SiC) with four different deposition channel sizes were fabricated via a novel laser-assisted chemical vapor infiltration (LA-CVI) method. Effects of infiltration channel sizes on microstructure and mechanical properties of C/SiC composites were investigated. The results showed that increasing the size of channels could expand infiltration passages and densification bands, which was consistent with theoretical calculations. Due to the presence of channels, the flexural strength of C/SiC composite increased by 14.47% when the channel diameter was 0.3?mm, compared to C/SiC composites prepared via conventional CVI process. Characteristics of matrix cracking and crack propagation on fracture surface were analyzed by using scanning electron microscopy. LA-CVI C/SiC composites displayed significantly improved damage-tolerant fracture behavior. Thus, findings of this work demonstrate that LA-CVI fabricated C/SiC composites are promising for a wide range of applications, particularly for enclosed-structure and thick-section C/SiC composites.     

Aligned carbon nanotube-reinforced silicon carbide composites produced by chemical vapor infiltration

A chemical vapor infiltration (CVI) technique was used to overcome most of the challenges involved in fabricating exceptionally-tough CNT/SiC composites. Nanotube pullout and sequential breaking and slippage of the walls of the CNTs during failure were consistently observed for all fractured CNT/SiC samples. These energy absorbing mechanisms result in the fracture strength of the CNT/SiC composites about an order of magnitude higher than the bulk SiC. The CVI-fabricated CNT/SiC composites have an strongly-bonded tube/matrix interface and an amorphous, crack-free SiC matrix, enabling the composites to withstand oxidization at 700–1600 °C in air.     

Mechanical and dielectric properties of SiCf/BN/SiBCN composites via different synthesis technologies

SiC fibers reinforced SiBCN ceramic matrix composites (SiC_f/BN/SiBCN composites) were synthesized by direct chemical vapor infiltration (CVI), polymer infiltration pyrolysis (PIP) or chemical vapor infiltration combined with polymer infiltration pyrolysis (CVI + PIP). It is shown that the insertion of a continuous and dense SiBCN matrix via the CVI process improves the flexural strength and modulus. Interface debonding and fiber pullout happened with 50–100 nm BN interface in CVI and CVI + PIP SiC_f/BN/SiBCN composites. The relative complex permittivity was measured in X-band. Higher ε′′ values in CVI-containing composites can be observed, which can be attributed to the accumulation of C and SiC phases and a multilayer matrix. Strong electromagnetic wave attenuation ability was obtained with high dielectric loss.     

Effects of fabrication processes on the properties of SiC/SiC composites

Precursor infiltration and pyrolysis (PIP) and chemical vapor infiltration (CVI) were used to fabricate SiC/SiC composites on a four-step 3D SiC fibre preform deposited with a pyrolytic carbon interface. The effects of fabrication processes on the microstructure and mechanical properties of the SiC/SiC composites were studied. Results showed the presence of irregular cracks in the matrix of the SiC/SiC composites prepared through PIP, and the crystal structure was amorphous. The room temperature flexural strength and modulus were 873.62 MPa and 98.16 GPa, respectively. The matrix of the SiC/SiC composites prepared through CVI was tightly bonded without cracks, the crystal structure had high crystallinity, and the room temperature bending strength and modulus were 790.79 MPa and 150.32 GPa, respectively. After heat treatment at 1300 °C for 50 h, the flexural strength and modulus retention rate of the SiC/SiC composites prepared through PIP were 50.01% and 61.87%, and those of the composites prepared through CVI were 99.24% and 96.18%, respectively. The mechanism of the evolution of the mechanical properties after heat treatment was examined, and the analysis revealed that it was caused by the different fabrication processes of the SiC matrix. After heat treatment, the SiC crystallites prepared through PIP greatly increased, and the SiOxCy in the matrix decomposed to produce volatile gases SiO and/or CO, ultimately leading to an increase in the number of cracks and porosity in the material and a decrease in the material load-bearing capacity. However, the size of the SiC crystallites prepared through CVI hardly changed, the SiC matrix was tightly bonded without cracks, and the load-bearing capacity only slightly changed.     

Enhanced microwave‐absorbing property of precursor infiltration and pyrolysis derived SiCf/SiC composites at X band: Role of carbon‐rich interphase

Ceramic matrix composites (CMCs) can be microwave‐absorbent when endowing the composite constituents with proper dielectric properties. In this work, we report a new method to enhance the microwave‐absorbing property of CMCs by in situ fabrication of a carbon‐rich interphase at the fiber/matrix interface. This was achieved in a SiC fiber reinforced SiC matrix (SiCf/SiC) composite fabricated by precursor infiltration and pyrolysis (PIP). We found that as the PIP temperature increased from 800 to 1000°C, the microwave‐absorbing property of the SiCf/SiC composite was significantly enhanced at X band, which also surpassed those of the SiC fiber and monolithic SiC ceramic fabricated at the same temperature. The dominant mechanism was studied by decoupling the effect of individual SiC fibers, SiC matrix, and fiber/matrix interface. The results showed that the SiC fiber and SiC matrix were barely microwave‐absorbent, due to their low dielectric losses. The microwave‐absorbing mechanism was finally ascribed to the fiber/matrix interface, which was carbon‐rich, containing Si and O elements. The interphase showed a conductivity that was superior to that of the fiber and the matrix, and mainly dominated the dielectric property of the overall composite. The results highlight the role of carbon‐rich interphase on the microwave‐absorbing property of CMCs.     

Tailoring Carbon Fiber/Carbon Nanotubes Interface to Optimize Mechanical Properties of Cf‐CNTs/SiC Composites

C_f/SiC composites were fabricated using fiber coatings including CNTs and matrix infiltration using the polymer impregnation and pyrolysis process. Interface between fiber and CNTs (CF/CNTs) was tailored to optimize mechanical properties of hybrid composites. The tailored interphases, such as Pyrocarbon (PyC) and PyC/SiC, protect fibers from degradation during the growth of CNTs successfully. Hybrid composites with well‐tailored CF/CNTs interface displayed significantly increased mechanical strength (352 ± 21 MPa) compared with that (34 ± 3 MPa) of composites reinforced with CNTs, which grown on carbon fibers directly. The interfacial bonding strength of hybrid composites was improved and optimized by tailoring the CF/CNTs interface. Interfacial failure modes were studied, and a firm interface bonding at the joint where CNTs grown was observed.     

Fabricating thick-section carbon fiber/silicon carbide composites by machining-aided chemical vapor infiltration

Chemical vapor infiltration (CVI) is a prominent process for fabricating carbon fiber/silicon carbide (C/SiC) composites. However, the preparation of enclosed-structure or thick-section C/SiC composites/components with CVI remains a challenge, since the difficulty of densification increases. Here, machining-aided CVI (MACVI) is designed, in which infiltration-assisting holes are utilized (machined) to increase matrix deposition. To validate the approach, thick-section (10 mm thick) C/SiC composites were fabricated by MACVI. Porosity analysis and microstructure characterization were performed on the fabricated MACVI C/SiC composites and their CVI counterparts, showing a density increase up to 12.7% and a porosity decrease up to 32.1%. The mechanical behavior of the fabricated MACVI C/SiC composites was characterized, showing an increase of flexural strength by a factor of 1.72 at most. Besides, the toughness also largely increases. Both the porosity decrease and the strength and toughness increase brought by MACVI demonstrate its effectiveness for fabricating stronger and tougher enclosed-structure or thick-section ceramic matrix composites/components.     

Effect of CVI SiC content on ablation and mechanism of C/C-SiC-ZrC-Cu composites

C/C-SiC-ZrC-Cu composites were fabricated by chemical vapor infiltration, precursor infiltration-pyrolysis and vacuum-pressure infiltration methods. During Cu infiltration, the Cu_6·69Si and Cu₃Si new phases are generated through reaction between SiC and molten Cu. The formed Cu_6·69Si, Cu₃Si, ZrC and SiC phases can improve the wettability and interface combination between Cu and the doped carbon matrix. The ablation tests demonstrate that the CVI SiC content significantly affects the structure of protective oxide layer, and induces inverse effects in ablation center at 2500 ^°C and 3000 ^°C. The relatively high CVI SiC content enhances the ablation resistance of composites at 2500 ^°C, but increases the linear ablation rate at 3000 ^°C due to the excessive evaporation and mechanical denudation. During ablation, the formed Si-Zr-C-O layer underneath ablation center and the Si-Cu-C-O layer on transition or marginal areas can prevent carbon matrix from serious oxidation. After ablation for 20 s, the C/C-SiC-ZrC-Cu composites with high CVI SiC content display the best anti-ablation property at 2500 ^°C, and the ablation rates are 3.5 ± 0.1 μm/s and 3.4 ± 0.1 mg/s.     

Microstructure control of highly oriented short carbon fibres in SiC matrix composites fabricated by direct ink writing

A novel method is proposed for fabricating highly oriented carbon fibre reinforced SiC ceramic composites (C_f/SiC) by direct ink writing (DIW). For the first time, the control of carbon fibers’ orientation in DIW was studied by numerical simulation. An interfacial layer was prepared by chemical vapor infiltration (CVI). The microstructure and phase composition of C_f/SiC were studied by scanning electron microscopy and X-ray diffraction, respectively. The results showed that fibers of different interfacial thicknesses could be obtained effectively by varying the CVI time. The breakage of short fibres remarkably improved the fracture toughness of the parts. The specimens showed excellent mechanical properties with bending strength of 274 ± 13 MPa and fracture toughness of 5.82 ± 0.25 MPa m^1/2. This method could be extended to the preparation of other resin and ceramic composites.     

The mechanical,thermophysical and electromagnetic properties of UD SiCf/SiC composites in different directions

Unidirectional (UD) silicon carbide (SiC) fiber-reinforced SiC matrix (UD SiC_f/SiC) composites with CVI BN interphase were fabricated by polymer infiltration-pyrolysis (PIP) process. The effects of the anisotropic distribution of SiC fibers on the mechanical properties, thermophysical properties and electromagnetic properties of UD SiC_f/SiC composites in different directions were studied. In the direction parallel to the axial direction of SiC fibers, SiC fibers bear the load and BN interphase ensures the interface debonding, so the flexural strength and the fracture toughness of the UD SiC_f/SiC composites are 813.0 ± 32.4 MPa and 26.1 ± 2.9 MPa·m^1/2, respectively. In the direction perpendicular to the axial direction of SiC fibers, SiC fibers cannot bear the load and the low interfacial bonding strengths between SiC fiber/BN interphase (F/I) and BN interphase/SiC matrix (I/M) both decrease the matrix cracking stress, so the corresponding values are 36.6 ± 6.9 MPa and 0.9 ± 0.5 MPa?m^1/2, respectively. The thermal expansion behaviors of UD SiC_f/SiC composites are similar to those of SiC fibers in the direction parallel to the axial direction of SiC fibers, and are similiar to those of SiC matrix in the direction perpendicular to the axial direction of SiC fibers. The total electromagnetic shielding effectiveness (EM SE_T) of UD SiC_f/SiC composites attains 32 dB and 29 dB when the axial direction of SiC fibers is perpendicular and parallel to the electric field direction, respectively. The difference of conductivity in different directions is the main reason causing the different SE_T. And the dominant electromagnetic interference (EMI) shielding mechanism is absorption for both studied directions.     

SiC陶瓷基体及抗氧化涂层

介绍了5种主要SiC基体的成型方法,分别是化学气相渗透(CVI)、聚合物先驱体浸渍-裂解法(PIP)、液相硅渗透法(LSI)、反应烧结法、化学气相反应法(CVR)。阐述了各种基体的组织结构、致密效率及陶瓷基复合材料的性能,其中CVI+PIP/LSI的复合成型技术可达到优化的制备过程,提高基体的组织结构和致密化效率;C/C及C/SiC复合材料表面化学气相转换法SiC涂层及多层涂层技术是提高CMC抗氧化性能的有效途径,并已得到工程实际验证。     

Oxidation behavior of C/SiC-SiBCN composites at high temperature

In order to improve the anti-oxidation performance of C/SiC composites at high temperature, C/SiC composites should be modified by self-healing components. SiBCN ceramic is an ideal self-healing component because of excellent oxidation resistance and thermal stability. C/SiC composites were modified by PDC SiBCN ceramic (C/SiC-SiBCN) by using CVI combined with polymer infiltration and on-line pyrolysis (PI-OP). The oxidation behaviors of C/SiC composites fabricated by CVI method and C/SiC-SiBCN composites fabricated by CVI + PI-OP method and CVI + PIP method at different temperatures in air were compared. The results showed that the strength retention ratios of the composites fabricated by the three methods decreased with the increase of temperature. Compared with the samples fabricated by the other two methods, the weight loss of the samples fabricated by CVI + PI-OP method was greater, but the strength retention ratio was higher.     

Fabrication of C/C-SiC composites using high-char-yield resin

Carbon fiber reinforced ceramic matrix composites (C/C-SiC composites) were fabricated using a type of high-char-yield phenolic resin with the char yield of 81.17 wt.%. Firstly, the fabric prepreg was prepared by spreading the phenolic resin solution onto the two dimensional carbon fiber plain weave fabric and dried consequently. Afterward, the resin was cured and then the carbon fiber reinforced polymer (CFRP) was pyrolyzed to get amorphous carbon. Finally, C/C-SiC composites were obtained through liquid silicon infiltration (LSI) process. SEM micrographs showed that the Si/SiC area was homogeneously dispersed in the matrix, and during the siliconization process, a layer of SiC was formed along the surface of carbon fibers or carbon matrix. The fiber volume of CFRP was about 40 vol.%, which was much lower than other studies. XRD result indicated that only β-SiC type was formed. The result of X-ray computed tomography clearly showed the structure changes before and after the melt infiltration process. Mechanical property test showed that the composites had fracture strength of 186 ± 23 MPa, and a flexural modulus of 106 ± 8 GPa.     

Investigation of CNT modification of epoxy resin in CFRP strengthening systems

The use of carbon fiber‐reinforced polymers (CFRPs) to reinforce old structures has become popular in recent years. In this study, the chemical structure of the epoxy resin used as the bonding agent in the CFRP strengthening system was modified by dispersing multi‐walled carbon nanotubes (MWCNTs) in order to improve the performance of the strengthening system. Composites were fabricated with different mixing orders employing the solvent‐assisted dispersion method and ultrasonic mixing. Thermogravimetric analysis, dynamic mechanical analysis, and tensile tests were conducted to investigate the effect of CNT dispersion and fabrication method on the thermal and mechanical properties of epoxy composite. In addition, the temperature‐dependent tensile behavior of fabricated composites was studied by performing tensile tests at elevated temperatures. The morphology of CNT/epoxy composites was characterized using scanning electron microscopy (SEM). Fourier transform infrared (FTIR) was also used to show the influence of solvent on the molecular structure of composites. Based on the experimental results, the decomposition temperature of the epoxy resin was heightened by 15°C as a result of solvent‐assisted dispersion of nanotubes. However, the glass transition temperature (T_g) was slightly reduced due to the solvent effect. FTIR analysis revealed that the solvent negatively affects the curing process of epoxy composite. A considerable enhancement was recorded in the tensile properties as a result of CNT infusion. This was attributed to the homogeneous dispersion of nanotubes which was shown by SEM images. Using solvent to disperse nanotubes led to the reduction of tensile strength of the epoxy composite at elevated temperature due to the lower T_g. POLYM. COMPOS. 37:1021–1033, 2016. © 2014 Society of Plastics Engineers     

Effect of high-temperature heat treatment on the microstructure and mechanical behavior of PIP-based C/C-SiC composites with SiC filler

C/C-SiC composites were fabricated by a combined process of chemical vapor deposition (CVD), slurry infiltration(SI), and precursor infiltration and pyrolysis (PIP). The microstructure and mechanical behavior were investigated for the dense C/C-SiC composites before and after high-temperature heat treatment. The results indicated that the sintering of the SiC matrix and the migration of the SiC matrix/fiber bundles weak interface occurred after high-temperature heat treatment at 1900 ℃. The SiC sintering resulted in an increase in the flexural strength of the C/C-SiC composites from 298.9 ± 35.0 MPa to 411.1 ± 57.3 MPa. The migration of the weak interface changed the direction of crack propagation, making the fracture toughness of the C/C-SiC composites decrease from 13.3 ± 1.7 MPa⋅m ^1/2 to 9.02 ± 1.5 MPa⋅m ^1/2.     

Effect of graphene and CNT reinforcement on mechanical and thermomechanical behavior of epoxy—A comparative study

Graphene‐nanoplateles (Gr) and multiwalled carbon nanotubes (CNTs) reinforced epoxy based composites were fabricated using ultrasonication, a strong tool for effective dispersion of Gr/CNTs in epoxy. The effect of individual addition of two different nanofillers (Gr and CNT) in epoxy matrix, for a range of nanofiller content (0.1–1 wt %), has been investigated in this study. This study compares mechanical and thermomechanical behavior of Gr and CNT reinforced epoxy. Gr reinforcement offers higher improvement in strength, Young's modulus, and hardness than CNT, at ≤0.2 wt %. However, mode‐I fracture toughness shows different trend. The maximum improvement in fracture toughness observed for epoxy‐Gr composite was 102% (with 0.3 wt % loading of Gr) and the same for epoxy‐CNT composite was 152% (with 0.5 wt % loading of CNT). Thorough microstructural studies are performed to evaluate dispersion, strengthening, and toughening mechanisms, active with different nanofillers. The results obtained from all the studies are thoroughly analyzed to comprehend the effect of nanofillers, individually, on the performance of the composites in structural applications. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46101.