Study of the Temperature Fields in Oil and Gas Strata with Water Injection Based on the Perturbation Method

The problem of the thermal action on oil and gas strata by injection of a heating medium using expansion in a small parameter is reduced to an infinite sequence of boundaryvalue problems that are solved by the method of integral transforms. It is shown that, with an appropriate selection of the small parameter, the zerothorder approximation corresponds to a spaceaveraged (across the stratum thickness) solution of the main problem and leads to a concentratedcapacity scheme that is constructed assuming that the stratum temperature is independent of the vertical coordinate. The first approximation permitted marked refinement of calculations according to the concentratedcapacity scheme and an evaluation of its error. Spacetime temperature distributions are presented that have been calculated using the analytical solutions obtained.     

TEM study of metastable β-phase decomposition in rapidly solidified Ti-6Al-4V alloy

A new rationale is presented for various decomposition products obtained from the metastable -phase found in Ti-6A1-4V alloy produced by hot isostatic pressing comminuted melt-spun fibres and cooled to room temperature by furnace cooling. This alloy has an -matrix with about 8 vol% retained -phase, which is supersaturated with -stabilizers to such an extent that the martensitic transformation has been suppressed. The metastable -phase decomposes by different modes during continuous cooling, depending on the actual composition of individual -grains. Less enrichment of vanadium and iron favours the direct formation of the equilibrium -phase from the -matrix, while greater enrichment of vanadium and iron leads to a spinodal decomposition of the metastable -phase, resulting in a + two-phase structure. During further continuous cooling, the -phase which is lean in -stabilizers will transform into isothermal -phase. In addition, an unknown phase has also been observed in the -phase, which is typified by the appearance of 1/2{112} reflections in the SAD patterns.     

Investigations of the copper isotope effect in oxygen-deficient YBa2Cu3O7−δ

We present data on the copper isotope effect (⁶³Cu-⁶⁵Cu), C_u =-nT_c/nm_Cu, for two isotopic pairs of oxygen-deficient YBa₂Cu₃O_7–, where varies between 0.06 and 0.52. _Cu is below 0.01 at =0.06 (fully oxygenated), it takes values between –0.14 and –0.34 in the 60 K plateau. Larger negative values of _Cu are observed away from the plateau. The dependence of _Cu is similar to that of the pressure effect dnT_c/dP.     

Electronic specific heat of La2−xSrxCu1−yMyO4(M=Ga,Zn): Impurity effects on a D-wave superconductor

The electronic specific heat C_el was studied in Ga- and Zn-doped La_2–xSr_xCuO₄ (0.16x0.22) at T10K. Partial substitution of Ga or Zn for Cu suppresses T_c and revives the T-linear electronic specific heat, T, markedly. The (y)/n vs T_c/T_c0 relation for Zn-doped samples with x0.2 is in good agreement with the theoretical one for resonant impurity scattering in a d-wave superconductor, while those for Ga-doped samples and for Zn-doped samples with x 0.2 deviate slightly from the theoretical curve. The deviation will be discussed in relation to changes in the magnetic properties of 3d electrons.     

Stability of metastable phases and microstructures in the ageing process of Al–Mg–Si ternary alloys

Precipitation behaviour of Al–Mg–Si alloys, with balanced (Mg/Si=2), excess silicon (Mg/Si<2) and excess magnesium (Mg/Si>2) compositions, were studied by differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and Vickers hardness tests. Four significant exothermic peaks were observed in DSC curves which were attributed to metastable clusters, , and stable phases. The peaks corresponding to and were formed closely in the DSC curves but showed different behaviour in isothermal annealing. The additional peak verifying the precipitation of phases, which has recently been proposed by some workers, was not detected. Transmission electron microscope observations and Vickers microhardness tests showed that precipitates played a major role in improving the hardness, but not precipitates. © 1998 Chapman & Hall     

Bone formation induced by calcium phosphate ceramics in soft tissue of dogs: a comparative study between porous α-TCP and β-TCP

Two kinds of tri-calcium phosphate ceramics (Ca/P = 1.50), -TCP and -TCP, which has the same macrostructure and microstructure, but different phase composition, were implanted in dorsal muscles of dogs. The samples were retrieved at 30, 45 and 150 days, respectively, after implantation, and were analyzed histologically. There were critically different tissue responses between -TCP ceramic and -TCP ceramic. Higher cell populations were observed inside the pores of -TCP than those of -TCP, bone tissue was found in -TCP at 45 and 150 days, but no bone formation could be detected in any -TCP implants in this study. On the other hand, the bone tissue in -TCP seemed to degenerate at 150 days. The results indicate that porous -TCP can induce bone formation in soft tissues of dogs; while the rapid dissolution of the ceramic and the higher local Ca²⁺, PO ₄ ^3- concentration due to the rapid dissolution of -TCP may resist bone formation in -TCP and the less rapid dissolution of -TCP may be detrimental to already formed bone in -TCP.     

Carbothermal production of β′-sialon from alumina,silica and carbon mixture

Mixtures of pure nanometer-sized amorphous silica and -alumina with the atomic ratio SiAl=1 were reduced by a stoichiometric amount of carbon between 1100 and 1450 °C in flowing nitrogen in order to produce -sialon powder. Using aqueous suspensions of starting materials, compacts with different microstructures were prepared for reaction. Silica reduction to SiO occurred at a temperature as low as 1300 °C and part of it was removed with flowing nitrogen. Carbothermal reaction involving nitrogen stated at 1350 °C and Si₂N₂O was found as an intermediate together with SiC, resulting in -sialon formation. Loss of silica from the system led to AlN formation. Decomposition of -sialon into sialon polytypoids (15R, 12H) was observed as a result of sialon and AlN reaction at 1450 °C. The reaction rate of sialon formation was slowed down compared to the carbothermal reduction of kaolin because of the lack of impurities. The microstructure of the reacted pellets influenced the reaction products, and the narrow pore size distribution as well as good homogeneity enhanced -sialon formation.On leave, from Silesian Technical University, Krasiskiego 8, 40-019 Katowice, Poland.     

Further properties of the Falkner-Skan equation

Summary We present some analytical perturbation results from which the skin-friction is accurately predicted over the range 1/2<<, where is the usual Falkner-Skan parameter. The first eigenvalue for various in the range 2<< is also calculated numerically and certain properties noted. We find, analytically, the whole set of eignesolutions for the case when is large.With 1 Figure     

Elastodynamic parameters for dynamic interface fracture mechanics

Summary Dynamic extension of cracks running along curvilinear interfaces of brittle bimaterials subjected to mechanical crack surface loads and superimposed thermal strains acting along the ligament is considered. This paper especially addresses the provision and discussion of elastodynamic interface parameters in order to assess quantitatively the bimaterial fracture in view of the governing physical features: applied mechanical and thermal strain loading, existence of an interface, crack-tip velocity and curvature of the interface contour. By utilizing the linear theory of thermoelasticity and adopting Stroh's method of generalized complex potentials, from the corresponding boundary and continuity conditions vectorial Hilbert problems are derived. It is shown that the parameters of the eigenvalues and of the eigenvectors of the Hilbert problems can be interpreted as elastodynamic interface mechanics parameters reading (,v _p, _Hf , _Hf ). Generalized Dundurs parameters of dynamics (, ) and consequently an associated generalized Dundurs diagram of dynamics are proposed. While the aforementioned elastodynamic interface parameters (, ,v _p, _Hf , _Hf ) do not assume the interface to be damaged, interfaces with running interface cracks generally cause two additional interface parameters, denoted as bimaterial constants (, _Hf ), where the latter is specific to the curvature of the interface in conjunction with the velocity of the interface crack. However, the bimaterial constants (, _Hf ) can be traced back to interface parameters for an uncracked bimaterial, namely to (, _Hf ).     

AC electrical conductivity of electron beam evaporated Cu-GeO2 thin cermet films

AC electrical properties of 410 nm think 30 at.wt% Cu-70 at.wt% GeO₂ thin films are reported for the frequency range 10⁴ to 10⁶ Hz and temperature range 150 to 425 K. The loss tangent (tan ) and the dielectric loss (/₀) are found to show striking minima around a cut-off frequency 10⁵ Hz. In the lower frequency range (10⁵ Hz), ₁() ^s T ⁿ is obeyed with s (0 to 0.51) increasing as a function of temperature and n (0.10 to 0.14) showing a very weak temperature dependence. In the higher frequency region (10⁵ Hz), ₁() and /₀ increase sharply leading to the quadratic behavior of ₁() with s equal to 2. These processes are discussed by analyzing an equivalent circuit which shows that at lower frequencies, the effects of series resistance in leads and contacts can be neglected, while at higher frequencies such effect give rise to spurious ² dependance for the conductance. A weakly activated AC conductivity and a frequency exponent s that increases with increasing temperature suggest that the low frequency behavior originates from carrier migration by tunneling process.     

Influence of pore volume on laser performance of Nd : YAG ceramics

For present study, 1.1 at% Nd-doped YAG ceramics with a controlled pore volume (150–930 vol ppm) were fabricated by a solid-state reaction method using high-purity powders. The scattering coefficients of Nd:YAG ceramics, obtained from Fresnel' equation, increased simply with increases in the pore volume. The cw laser output power of Nd:YAG ceramics was clearly related to the scattering coefficients of the specimens examined in the present works, which in turn were affected on the pore volume. The effective scattering coefficients of Nd:YAG ceramics with a pore volume of 150 vol ppm were nearly equivalent to those of a 0.9 at%Nd:YAG single crystal by Czochralski method. As the exciting power was increased under excitation by an 808-nm diode laser, however, the laser output power of the Nd:YAG ceramics exceeded that of the Nd:YAG single crystal because of the fairly large amount of Nd additives. The lasing performance of the Nd:YAG ceramics changed drastically with change in pore volume. On the other hand, lasing performance was not affected by the existence of grain boundaries in the polycrystalline Nd:YAG ceramics.     

Comparative study of solubilities of hydrogen,nitrogen and carbon in α-iron

Solubility data of hydrogen, nitrogen and carbon in -iron are analysed on the basis of statistical thermodynamics. Present analysis appears to yield realistic values for the enthalpy term of the solutions of these interstitial elements into -Fe, while the entropy terms remain ambiguous. During the course of this analysis a parameter _x, which refers to the solubility limit of the specific interstitial element X (X=hydrogen, nitrogen or carbon), is also estimated; _H< _N< _C. This order of _X values appears to be in accord with the observation that, under normal conditions, the solubility of carbon is the highest and that of hydrogen the lowest in -Fe, while the atomic size increases with the order hydrogen相似文献   

On annealed Ni-34.6 at % Al at 1523 K and effects of cooling rates

The microstructures and room temperature mechanical properties of melt spun Ni-34.6 at % Al annealed at 1523 K for 2 h and cooled at different rates were studied. The annealed microstructures and bend ductility were sensitive to the cooling rate. The distribution and relative content of precipitation were important factors for enhancement of bend ductility of the annealed ribbon. The best bend ductility of the annealed ribbon reached 7.6%, which was considerably better than the as-melt spun ribbon. The emission and transmission of dislocations from ductile into to satisfy the need of deformation compatibility played a key role in the improvement of the ductility.     

Ageing characteristics of rapidly solidified Al-Li-Ti alloys at 473 K

The influence of titanium on the precipitate free zones (PFZs) and on the stable phase is investigated in four melt-spun Al-Li-Ti alloys with 2 mass% lithium and 0.10–0.35 mass% titanium. Rapid solidification gives rise to a homogeneous distribution of titanium on the wheel side of the ribbons, and to a cellular distribution of solute atoms in intermediate regions and on the gas side. Heat treatments of up to 1000 h at 473 K do not modify titanium distribution, which remains in solid solution. During ageing, preferential coarsening of particles occurs on cell walls. The growth rate of the PFZs is lower than in other Al-Li alloys and is mainly controlled by the titanium concentration of the alloys. The nucleation and growth of the stable phase is also delayed by the presence of titanium. These results indicate that the effect of titanium in solid solution is to retain vacancies thus reducing lithium diffusion rate.     

The neural net of neural network research

In this paper we discuss the limits and potentials of bibliometric mapping based on a specific co-word analysis. The subject area is neural network research. Our approach is a simulation of expert assessment by offering the reader a narrative of the field which can be used as background information when reading the bibliometric maps. The central issue in the applicability of bibliometric maps is whether these maps may supply additional intelligence to users. In other words, whether such a bibliometric tool has an epistemological value, in the sense that it ecriches existing knowledge by supplying unexpected relations between specific pieces of knowledge (synthetic value) or by supplying unexpected problems (creative value). We argue that sophisticated bibliometric mapping techniques are indeed valuable for open new avenues to study science as a self-organizing system in the form of a neural network like structure of which the bibliometric map is a first-order aproximation. In that sense, this paper deals with the neural net of neural network research as our bibliometric techniques in fact mimic a connectionistic approach.     

Distribution characteristics of mechanical properties and correlation between the respective properties on S35C carbon steel

Mechanical properties of tensile strength, , upper yield stress, _SU, lower yield stress, _SL elongation, , area reduction, , Vickers hardness, H _v, and impact absorbed energy, E, were examined using 50 specimens of S35C carbon steel, which were machined from two bars supplied from the same charged and heat-treated material. Distribution characteristics of these properties are discussed, and the correlation between each pair of them is investigated from a statistical viewpoint. The main conclusions obtained are summarized as follows; distribution characteristics of _B, _SL, , , H _v and E are well approximated by a normal distribution, but those of asu are not approximated as well by this type of distribution. In the latter case, a Weibull distribution is preferable to represent the distribution pattern. No significant correlation was observed between each pair of the above mechanical properties. Consequently, individual properties have the inherent distribution characteristics independent of the other properties.     

Microstructure and mechanical properties of rapidly quenched L20 and L20+L12 alloys in Ni-Al-Fe and Ni-Al-Co systems

Ductile L2₀-type wires and+L1₂-type duplex wires with high strengths and large elongation in the Ni-Al-Fe and Ni-Al-Co ternary systems have been manufactured directly from the liquid state by an in-rotating-water spinning method. The wire diameter was in the range 80 to 180m and the average grain size was 2 to 4m for the wires and 0.2 to 1.0m for the+ wires. _y, _f and _p of the wires were found to be about 360 to 760 MPa, 560 to 960 MPa, and 0.2 to 5.5%, respectively, for the Ni-Al-Fe system, those of the+ wires were about 395 to 660 MPa, 670 to 1285 MPa, and 3.5 to 17%, respectively, for the Ni-Al-Fe system, and about 260 to 365 MPa, 600 to 870 MPa, and 4.0 to 7.0%, respectively, for the Ni-Al-Co system. Cold-drawing caused a significant increase in _y and _f and the values attained were about 1850 and 2500 MPa, respectively, for Ni-20Al-30Fe and Ni-25Al-30Co wires drawn to about 90% reduction in area. The high strengths, large elongation and good cold-workability of the melt-quenched and+ compound wires have been inferred to be due to the structural change into a low-degree ordered state containing a high density of phase boundaries, suppression of grain-boundary segregation and refinement of grain size.     

The sequence of precipitation in 339 aluminum castings

The precipitation sequences in direct-quenched from the die (DQD) and solution-treated (SOL) 339 aluminum have been determined by a combination of differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). DSC scans for the alloy in both conditions exhibit two distinct exothermic peaks, each associated with a unique precipitate. The peak temperatures for precipitation in the DQD and SOL alloys differ by only a few degrees. TEM of samples heated to the lower temperature peak shows that the first precipitate to form in the DQD alloy is S (Al₂CuMg), whereas in the SOL alloy it is (Mg₂Si). The principal precipitate associated with the higher temperature peak in both DQD and SOL alloys is Si. The DSC peak temperature identifies the specific precipitate in 339 Al, but the peak area is not a reliable measure of precipitate density. Nano-indentation of the dendrites shows that the strength provided by the precipitates increases in the sequence Si < S < . However, their thermal stability increases in the reverse order.     

The athermal α → ω transformation in Zr-2 at% Nb alloy

The athermal transformation in Zr-2 at.% Nb alloy has been investigated by transmission electron microscopy. Analysis of the selected-area diffraction pattern has shown that the orientation relationships between the omega and the parent-phase in quenched Zr-2 at.% Nb alloy are the same as have been previously observed for the reaction in pure zirconium. Thus it was deduced that the direct transition has taken place in the alloy during cooling. The-originated -particles were visualized using the dark-field technique. The formation of the athermal omega in the-region of-stabilized Zr-Nb alloy is discussed in terms of the relative positions of the free energy equilibrium curvesT ₀ ,T ₀ ,T ₀ and the correspondingM _s ,M _s andT _s start curves. It is concluded that the omega phase can occur over a much wider range of alloy compositions than is usually recognized on the basis of transformation data.     

Numerical Calculation of the Flow Regimes of a Fluid Partially Filling a Horizontal Rotating Heat‐Exchange Cylinder

Consideration is given to a numerical determination of a twodimensional unsteady viscous flow with the free surface in a stationarily rotating horizontal cylinder in which heatexchange processes are carried out. The markerandcell method in a polar coordinate system is used. The features of modeling of the walllayer regime and the circulating flow regime that occur in rapid and slow rotation of the cylinder, respectively, are discussed. Based on the given results of numerical calculations, the influence of the Reynolds number on the character of flow is analyzed.