Microwave Dielectric Properties of CaTiO3-CaAl1/2Nb1/2O3 Ceramics Doped with Li3NbO4

The microwave dielectric properties of CaTi_{1− x} (Al_1/2Nb_1/2) _x O₃ solid solutions (0.3 ≤ x ≤ 0.7) have been investigated. The sintered samples had perovskite structures similar to CaTiO₃. The substitution of Ti⁴⁺ by Al³⁺/Nb⁵⁺ improved the quality factor Q of the sintered specimens. A small addition of Li₃NbO₄ (about 1 wt%) was found to be very effective for lowering sintering temperature of ceramics from 1450–1500° to 1300°C. The composition with x = 0.5 sintered at 1300°C for 5 h revealed excellent dielectric properties, namely, a dielectric constant (ɛ_r) of 48, a Q × f value of 32 100 GHz, and a temperature coefficient of the resonant frequency (τ_f) of −2 ppm/K. Li₃NbO₄ as a sintering additive had no harmful influence on τ_f of ceramics.     

Dielectric Properties of (1−x)CaTiO3–xCa(Zn1/3Nb2/3)O3 Ceramic System at Microwave Frequency

The microwave dielectric properties of the (1− x )CaTiO₃– x Ca(Zn_1/3Nb_2/3)O₃ ceramic system have been investigated. The ceramic samples sintered at 1300°–1450°C for 4 h in air exhibit orthorhombic pervoskite and form a complete solid solution for different x value. When the x value increased from 0.2 to 0.8, the permittivity ɛ_r decreased from 115 to 42, the unloaded quality factor Q × f increased from 5030 to 13 030 GHz, and the temperature coefficient τ_f decreased from 336 to −28 ppm/°C. When x =0.7, the best combination of dielectric properties, a near zero temperature coefficient of resonant frequency of τ_f∼−6 ppm/°C, Q × f ∼10 860 GHz and ɛ_r∼51 is obtained.     

Structure and Microwave Dielectric Characteristics of Ca1+xNd1−xAl1−xTixO4 Ceramics

CaNdAlO₄ microwave dielectric ceramics were modified by Ca/Ti co-substitution, and their dielectric characteristics were evaluated along with their structure and microstructures. Ca_{1+ x} Nd_{1− x} Al_{1− x} Ti _x O₄ ( x =0, 0.025, 0.05, 0.10, 0.15, 0.20) ceramics with the relative density of over 95% theoretical density were obtained by sintering at 1400°–1450°C in air for 3 h, where the K₂NiF₄-type solid solution single phase was determined from the compositions of x <0.20, while a small amount of CaTiO₃ secondary phase was detected for x =0.20. With Ca/Ti co-substitution in CaNdAlO₄ ceramics, the dielectric constant (ɛ_r) increased with increasing x , and the temperature coefficient of resonant frequency (τ_f) was adjusted from negative to positive, while the Q × f ₀ value increased significantly at first and reached an extreme value at x =0.025 and the maximum at x =0.15. The best combination of microwave dielectric characteristics were achieved at x =0.15 (ɛ_r=19.5, Q × f ₀=93 400 GHz, τ_f=−2 ppm/°C). The improvement of the Q × f ₀ value primarily originated from the reduced interlayer polarization with Ca/Ti co-substitution, while the decreased tolerance factor, the subsequent increased interlayer stress, and the appearance of CaTiO₃ secondary phase brought negative effects upon the Q × f ₀ value.     

Preparation and Dielectric Properties of Low-Temperature-Sinterable (Zr0.8Sn0.2)TiO4 Powder

Low-temperature-sinterable (Zr_0.8Sn_0.2)TiO₄ powders were prepared using 3 mol% Zn(NO₃)₂ additive and then compared with powders prepared using 3 mol% ZnO additive and no additives. Sintering at 1200°C for 2 h produced a dielectric ceramic with ρ= 98.6% of theoretical density (TD), ɛ_r= 38.4, Q × f (GHz) = 42000, and τ _f =−1 ppm/°C. Sintering at 1250°C resulted in an excellent dielectric with ρ= 99% of TD, epsilon_r= 40.9, Q × f (GHz) = 49000, and τ _f =−2 ppm/°C. Scanning electron microscopy showed a microstructure with grains measuring 0.5 to 1 μm, and transmission electron microscopy revealed secondary phase in the grain boundaries.     

High Q Microwave Dielectric Ceramics in (Ni1−x Znx)Nb2O6 System

(Ni_{1− x} Zn _x )Nb₂O₆, 0≤ x ≤1.0, ceramics with >97% density were prepared by a conventional solid-state reaction, followed by sintering at 1200°–1300°C (depending on the value of x ). The XRD patterns of the sintered samples (0≤ x ≤1.0) revealed single-phase formation with a columbite ( Pbcn ) structure. The unit cell volume slightly increased with increasing Zn content ( x ). All the compositions showed high electrical resistivity (ρ_dc=1.6±0.3 × 10¹¹Ω·cm). The microwave (4–5 GHz) dielectric properties of (Ni_{1− x} Zn _x )Nb₂O₆ ceramics exhibited a significant dependence on the Zn content and to some extent on the morphology of the grains. As x was increased from 0 to 1, the average grain size monotonically increased from 7.6 to 21.2 μm and the microwave dielectric constant (ɛ'_r) increased from 23.6 to 26.1, while the quality factors ( Q _u× f ) increased from 18 900 to 103 730 GHz and the temperature coefficient of resonant frequency (τ_f) increased from −62 to −73 ppm/°C. In the present work, we report the highest observed values of Q _u× f =103 730 GHz, and ɛ'_r=26.1 for the ZnNb₂O₆-sintered ceramics.     

Effects of La on Dielectric and Piezoelectric Properties of Pb1−xLa2x/3(Nb0.95Ti0.0625)2 O6 Ceramics

Ceramics with the chemical compositions of Pb_{1− x} La_{2 x /3}(Nb_0.95Ti_0.0625)₂O₆ (0≤ x ≤0.060) (PLTN) were prepared by the conventional solid-state reaction method. X-ray diffraction analysis indicated that Ti and La doping not only decreased the rhombohedral–tetragonal phase transformation temperature, but also stabilized the orthorhombic phase of PLTN ceramics. All ceramics sintered at 1190°–1250°C had shown the pure orthorhombic ferroelectric phase. La doping suppresses grain growth and inhibits the formation of pores and cracks, resulting in an increase in relative density up to 97%. The amount of La doping to PLTN ceramics obviously affect ceramics' piezoelectric constant ( d ₃₃) and dielectric loss (tanδ). The sample with x =0.015 possesses high Curie temperature ( T _c=560°C), low dielectric loss (tanδ=0.0054), and excellent piezoelectric constant ( d ₃₃=92 pC/N), presenting a high potential to be used in high-temperature applications as piezoelectric transducers.     

Synthesis of BaCu(B2O5) Ceramics and their Effect on the Sintering Temperature and Microwave Dielectric Properties of Ba(Zn1/3Nb2/3)O3 Ceramics

BaCu(B₂O₅) ceramics were synthesized and their microwave dielectric properties were investigated. BaCu(B₂O₅) phase was formed at 700°C and melted above 850°C. The BaCu(B₂O₅) ceramic sintered at 810°C had a dielectric constant (ɛ_r) of 7.4, a quality factor ( Q × f ) of 50 000 GHz and a temperature coefficient of resonance frequency (τ_f) of −32 ppm/°C. As the BaCu(B₂O₅) ceramic had a low melting temperature and good microwave dielectric properties, it can be used as a low-temperature sintering aid for microwave dielectric materials for low temperature co-fired ceramic application. When BaCu(B₂O₅) was added to the Ba(Zn_1/3Nb_2/3)O₃ (BZN) ceramic, BZN ceramics were well sintered even at 850°C. BaCu(B₂O₅) existed as a liquid phase during the sintering and assisted the densification of the BZN ceramic. Good microwave dielectric properties of Q × f =16 000 GHz, ɛ_r=35, and τ_f=22.1 ppm/°C were obtained for the BZN+6.0 mol% BaCu(B₂O₅) ceramic sintered at 875°C for 2 h.     

Effect of V2O5 Doping on the Sintering and Dielectric Properties of M-Phase Li1+x−yNb1−x−3yTix+4yO3 Ceramics

The effect of the addition of V₂O₅ on the structure, sintering and dielectric properties of M -phase (Li_{1+ x − y} Nb_{1− x −3 y} Ti _x +4 _y )O₃ ceramics has been investigated. Homogeneous substitution of V⁵⁺ for Nb⁵⁺ was obtained in LiNb_{0.6(1− x )}V_{0.6 x} Ti_0.5O₃ for x ≤ 0.02. The addition of V₂O₅ led to a large reduction in the sintering temperature and samples with x = 0.02 could be fully densified at 900°C. The substitution of vanadia had a relatively minor adverse effect on the microwave dielectric properties of the M -phase system and the x = 0.02 ceramics had [alt epsilon]_r= 66, Q × f = 3800 at 5.6 GHz, and τ_f= 11 ppm/°C. Preliminary investigations suggest that silver metallization does not diffuse into the V₂O₅-doped M -phase ceramics at 900°C, making these materials potential candidates for low-temperature cofired ceramic (LTCC) applications.     

Microwave Dielectric Properties of 5Li2O–0.583Nb2O5–3.248TiO2 Ceramics with V2O5

The effects of V₂O₅ addition on the sintering behavior, microstructure, and the microwave dielectric properties of 5Li₂O–0.583Nb₂O₅–3.248TiO₂ (LNT) ceramics have been investigated. With addition of low-level doping of V₂O₅ (≤2 wt%), the sintering temperature of the LNT ceramics could be lowered down to around 920°C due to the liquid phase effect. A secondary phase was observed at the level of 2 wt% V₂O₅ addition. The addition of V₂O₅ does not induce much degradation in the microwave dielectric properties but lowers the τ_f value to near zero. Typically, the excellent microwave dielectric properties of ɛ_r=21.5, Q × f =32 938 GHz, and τ_f=6.1 ppm/°C could be obtained for the 1 wt% V₂O₅-doped sample sintered at 920°C, which is promising for application of the multilayer microwave devices using Ag as an internal electrode.     

Microstructure and Microwave Dielectric Properties of (1−x)Ca(Mg1/3Ta2/3)O3/xCaTiO3 Ceramics

Dense (1− x )Ca(Mg_1/3Ta_2/3)O₃/ x CaTiO₃ ceramics (0.1≤ x ≤0.9) were prepared by a solid-state reaction process. The crystal structures and microstructures were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Single-phase solid solutions were obtained in the entire composition range. Long-range 1:2 ordering of B-site cations and oxygen octahedra tilting lead to the monoclinic symmetry with space group P 2₁/ c for x =0.1. For x above 0.1, the long-range ordering was destroyed and the crystal structure became the orthorhombic with space group Pbnm . The microwave dielectric properties showed a strong dependence on the composition and microstructure. The dielectric constant and temperature coefficient of resonant frequency increased nonlinearly as the CaTiO₃ content increased while the Qf values decreased approximately linearly. Good combination of microwave dielectric properties was obtained at x =0.45, where ɛ_r=45.1, Qf =34 800 GHz, and τ_f=17.4 ppm/°C.     

High-Q Microwave Dielectrics in the (Mg1−xCox)2TiO4 Ceramics

The microwave dielectric properties and the microstructures of (Mg_{1− x} Co _x )₂TiO₄ ceramics prepared by the conventional solid-state route were investigated. Lattice parameters were also measured for specimens with different x . The formation of solid solution (Mg_{1− x} Co _x )₂TiO₄ ( x =0.02–0.1) was confirmed by the X-ray diffraction patterns, energy dispersive X-ray analysis, and the lattice parameters measured. By increasing x from 0 to 0.05, the Q × f of the specimen can be tremendously boosted from 150 000 GHz to a maximum of 286 000 GHz. A fine combination of microwave dielectric properties (ɛ_r∼15.7, Q × f ∼286 000 GHz at 10.4 GHz, τ_f∼−52.5 ppm/°C) was achieved for (Mg_0.95Co_0.05)₂TiO₄ ceramics sintered at 1390°C for 4 h. Ilmenite-structured (Mg_0.95Co_0.05)TiO₃ was detected as a second phase. The presence of the second phase would cause no significant variation in the dielectric properties of the specimen because it possesses compatible properties compared with that of the main phase. In addition, only a small deviation in the dielectric properties was monitored for specimens with x =0.04–0.05 at 1360°–1420°C. It not only provides a wide process window but also ensures an extremely reliable material proposed as a very promising dielectric for low-loss microwave and millimeter wave applications.     

Reduced Dielectric Loss of Modified ZnNb2O6 Ceramics by Substituting Nb5+ with Ta5+

The effects of substituting Nb⁵⁺ with Ta⁵⁺ on the microwave dielectric properties of the ZnNb₂O₆ ceramics were investigated in this study. The forming of Zn(Nb_{1− x} Ta _x )₂O₆ ( x =0–0.09) solid solution was confirmed by the measured lattice parameters and the EDX analysis. By increasing x , not only could the Q × f of the Zn(Nb_{1− x} Ta _x )₂O₆ ( x =0–0.09) solid solution be tremendously boosted from 83 600 GHz at x =0 to a maximum 152 000 GHz at x =0.05, the highest ɛ_r∼24.6 could also be achieved simultaneously. It was mainly due to the uniform grain morphology and the highest relative density of the specimen. A fine combination of microwave dielectric properties (ɛ_r∼24.6, Q × f ∼152 000 GHz at 8.83 GHz, τ_f∼–71.1 ppm/°C) was achieved for Zn(Nb_0.95Ta_0.05)₂O₆ solid solution sintered at 1175°C for 2 h.     

Effect of Oxygen Partial Pressure During Liquid-Phase Sintering on the Dielectric Properties of 0.9MgTiO3–0.1CaTiO3

Microstructural evolution and microwave dielectric properties of liquid-phase-sintered 0.9MgTiO₃–0.1CaTiO₃ dielectric ceramic material have been investigated as a function of oxygen partial pressure (     ) during sintering. Sintering in a weakly reducing atmosphere (     =10⁻¹⁴ atm) generally increased the density, permittivity, quality factor ( Q × f ), and the temperature coefficient of resonance frequency (τ_f), but further reducing atmosphere down to     of 10⁻¹⁴ atm generally decreased Q × f and τ_f. When the 5 wt% lithium borosilicate glass-added specimen was sintered at 950°C and     =10⁻¹⁴ atm, it demonstrated a permittivity of 18.8, Q × f of 19 000 GHz, and τ_f of 10 × 10⁻⁶ K⁻¹.     

Effect of Bi2O3 Addition on the Sintering Temperature and Microwave Dielectric Properties of Zn2SiO4 Ceramics

Bi₂O₃ was added to a nominal composition of Zn_1.8SiO_3.8 (ZS) ceramics to decrease their sintering temperature. When the Bi₂O₃ content was <8.0 mol%, a porous microstructure with Bi₄(SiO₄)₃ and SiO₂ second phases was developed in the specimen sintered at 885°C. However, when the Bi₂O₃ content exceeded 8.0 mol%, a liquid phase, which formed during sintering at temperatures below 900°C, assisted the densification of the ZS ceramics. Good microwave dielectric properties of Q × f =12,600 GHz, ɛ_r=7.6, and τ_f=−22 ppm/°C were obtained from the specimen with 8.0 mol% Bi₂O₃ sintered at 885°C for 2 h.     

Microstructures and Microwave Dielectric Characteristics of Ca(Zn1/3Nb2/3)O3 Complex Perovskite Ceramics

Ca(Zn_1/3Nb_2/3)O₃ microwave dielectric ceramics were prepared using a solid-state reaction process, and their microwave dielectric properties were evaluated as functions of sintering and postdensification annealing conditions. The relationship between microwave dielectric properties and processing was interpreted through the variation of microstructures. The dielectric constant showed slight variation with sintering and annealing conditions, but the Q × f value increased at first and then decreased with increased sintering temperature, and annealing in oxygen indicated significant improvement in Q × f , especially for the specimens sintered at higher temperatures. The good microwave dielectric properties were obtained in the ceramics sintered at 1225°C in air for 3 h and annealed at 1100°C in oxygen for 8 h: ɛ= 34.1, Q × f = 15 890 GHz, τ_f=−48 ppm/°C.     

Structure and Microwave Dielectric Properties of Hexagonal Ba[Ti1−x(Ni1/2W1/2)x]O3 Ceramics

Microwave dielectric ceramics with the composition of Ba[Ti_{1− x} (Ni_1/2W_1/2) _x ]O₃ ( x =0.4–0.6) were prepared by a solid-state reaction method. The evolution of the crystalline phases was investigated by X-ray powder diffraction analysis. A cubic-to-hexagonal phase transition occurred between 1000° and 1300°C. The phase transition is irreversible; thus, the hexagonal phase remains stable at room temperature. The X-ray powder diffraction data for x =0.5 were refined using the Rietveld method. It was identified as a h -BaTiO₃-type hexagonal perovksite with the space group of P 6₃/ mmc . It also reveals that random occupancy of Ti⁴⁺ and W⁶⁺ ions occurs in the B-site substructures, whereas Ni²⁺ ions exclusively occupy the octahedral site in the corner-sharing octahedron. The dielectric properties of dense-sintered ceramics were characterized at microwave frequencies. With an increase in x from 0.4 to 0.6, the Q × f value increased from 26 700 to 42 000 GHz, whereas ɛ_r decreased from 29.8 to 20.0, and τ_f from +6.5 to −9.9 ppm/°C.     

A- and B Site Cosubstituted Ba6−3xSm8+2xTi18O54Microwave Dielectric Ceramics

Tin (Sn) substitution into the B-site and Nd/Sn cosubstitution into the A- and B-sites were investigated in a Ba _{6−3 x} Sm_{8+2 x} Ti₁₈O₅₄solid solution ( x = 2/3). A small amount of tin substitution for titanium improved the temperature coefficient of resonant frequency (τ_f) but led to a decrease of the relative dielectric constant (ɛ) and the quality factor ( Qf ). The Ba_{6−3 x} Sm_{8+2 x} (Ti_{1− z} Sn_z)₁₈O₅₄-based tungsten-bronze phase became unstable for compositions with a tin content of ≥10 mol%, where BaSm₂O₄and Sm₂(Sn,Ti)₂O₇appeared, and finally, these phases became the major phases. On the other hand, Nd/Sn cosubstitution led to a good combination of high ɛ, high Qf , and near-zero τ_f. Excellent microwave dielectric properties were achieved in Ba_{6−3 x} (Sm_{1− y} Nd _y )_{8+2 x} (Ti_{1− z} Sn _z )₁₈O₅₄ceramics with y = 0.8 and z = 0.05 sintered at 1360°C for 3 h: ɛ= 82, Qf = 10 000 GHz, and calculated τ_f=+17 ppm/°C. The tolerance factor and electronegativity difference exhibited important effects on the microwave dielectric properties, especially the Qf value. A large tolerance factor and high electronegativity difference generally led to a higher Qf value.     

A/B Site Modified CaTiO3 Dielectric Ceramics for Microwave Application

(Li_1/2Nd_1/2)²⁺ substitution into the A site and (Mg_1/3Ta_2/3)⁴⁺ substitution into the B site of CaTiO₃ ceramic were investigated, respectively. The modified CaTiO₃ dielectric ceramics prepared by conventional solid-state method exhibit single perovskite structure and improved dielectric properties. Optimal microwave dielectric properties of ɛ_r=112.6, Q × f =4480 GHz, τ_f=8.2 ppm/°C in [Ca_0.4(Li_1/2Nd_1/2)_0.6] TiO₃ and ɛ_r=60.2, Q × f =36900 GHz, τ_f=−10.1 ppm/°C in Ca[Ti_0.4(Mg_1/3Ta_2/3)_0.6] O₃ are obtained, which indicates their potential for microwave application. The effects of change of crystal structure on dielectric properties are also discussed.     

Microwave Dielectric Properties of Low-Fired ZnNb2O6 Ceramics with BiVO4 Addition

The BiVO₄ additive was found effective for low-temperature firing of ZnNb₂O₆ polycrystalline ceramics below 950°C in air without a serious degradation in their microwave dielectric properties. Dense BiVO₄-doped ZnNb₂O₆ samples of a relative sintered density over 95% could be prepared even at 925°C. An optimally processed specimen exhibited excellent microwave dielectric properties of Q · f = 55000 GHz, ɛ_r= 26, and τ_f=−57 ppm/°C. With increasing BiVO₄ addition up to 20 mol% relative to ZnNb₂O₆, while the quality factor Q · f was gradually decreased, the relative dielectric constant, ɛ_r, was linearly increased and the temperature coefficient of resonant frequency, τ_f, was slightly increased. The variations in Q · f and ɛ_r are surely attributable to the residual BiVO₄ in the ZnNb₂O₆ matrix. An unexpected slight increase in τ_f is probably due to the formation of the Bi(V,Nb)O₄-type solid solution.     

Synthesis and Microwave Dielectric Properties of Re3Ga5O12 (Re: Nd, Sm, Eu, Dy, Yb, and Y) Ceramics

Re₃Ga₅O₁₂ (Re: Nd, Sm, Eu, Dy, Yb, and Y) garnet ceramics were synthesized and their microwave dielectric properties were investigated for advanced substrate materials in microwave integrated circuits. The Re₃Ga₅O₁₂ ceramics sintered at 1350°–1500°C had a high-quality factor ( Q × f ) ranging from 40 000 to 192 173 GHz and a low-dielectric constant (ɛ_r) of between 11.5 and 12.5. They also exhibited a relatively stable temperature coefficient of resonant frequency (τ_f) in the range of −33.7 to −12.4 ppm/°C. In particular, the Sm₃Ga₅O₁₂ ceramics sintered at 1450°C exhibited good microwave dielectric properties of ɛ_r=12.4, Q × f =192 173 GHz, and τ_f=−19.2 ppm/°C.