Effect of texture evolution on tensile properties of Al–Ni eutectic alloy fabricated by equal channel angular pressing

Abstract

The present study investigated in detail the effect of texture evolution on the mechanical properties of an Al–5·7 wt-%Ni eutectic alloy, which was subjected to severe plastic deformation by the equal channel angular pressing (ECAP) technique. The ECAP procedure was carried out using two strain introduction methods, route B_C and route A, at a temperature of 298 K and a pressing rate of 0·33 mm s^?1. The as pressed microstructures were observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results indicated that the Al–Ni eutectic alloy specimens after ECAP processing by route B_C and route A methods had very different microstructures, which strongly affected the tensile properties of the specimens. It was demonstrated that after ECAP processing by route B_C, fine Al₃Ni particles of ～300 nm were homogeneously dispersed in the aluminium matrix, and the specimens showed no clear anisotropy in tensile properties. After ECAP processing by route A, however, eutectic textures containing α-Al and Al₃Ni fibrous dispersoids had a highly anisotropic distribution and were demonstrated to have significantly anisotropic tensile properties. Based on the experimental results, the fracture mechanism during tensile testing of the Al–Ni eutectic alloy using different strain induction methods is discussed.     

Influence of equal channel angular extrusion processing parameters on the microstructure and mechanical properties of Mg–Al–Y–Zn alloy

An as-cast Mg–Al–Y–Zn alloy was successfully processed by equal channel angular extrusion (ECAE) in the temperature range of 225–400 °C, and the influences of processing temperature on the microstructure and mechanical properties were investigated. The use of back pressure during one-pass ECAE of Mg–Al–Y–Zn alloy was favorable for eliminating the undeformed area in the billet. At the processing temperature below 250 °C, the microstructures were characterized by unrecrystallised structure and the precipitated phase Mg₁₇Al₁₂ was elongated along the extrusion direction. With increasing processing temperature to 350 °C, a large number of recrystallised grains were obtained. Increasing processing temperature promoted workability but led to decrease in the strength of Mg–Al–Y–Zn alloy. Then billets of as-cast Mg–Al–Y–Zn alloy were extruded at different numbers of ECAE passes. It was found that the microstructure was effectively refined by ECAE and mechanical properties were improved with numbers of ECAE passes increasing from one-pass to four passes. However, strengths decreased slightly after five passes though the grain size decreased considerably.     

Effects of equal channel angular pressing on the strength and toughness of Al–Cu alloys

Tensile and impact tests were performed on Al–0.63 wt%Cu and Al–3.9 wt%Cu alloys subjected to equal channel angular pressing (ECAP) with different number of passes. Besides the tensile properties, data about the static toughness and the impact toughness were obtained. The strength and the toughness of the Al–Cu alloys were ameliorated and upgraded to a high level collectively. In addition, fracture surface observations show that the fracture behavior of the Al–Cu alloys changes from brittle mode to ductile mode after multi-pass ECAP.     

Texture evolution in an Al–Cu alloy during equal channel angular pressing: the effect of starting microstructure

In this article, the effect of initial microstructure on the texture evolution in 2014 Al alloy during equal channel angular pressing (ECAP) through route A has been reported. Three heat treatment conditions were chosen to generate the initial microstructures, namely (i) the recrystallization anneal (as-received), (ii) solution treatment at 768 K for 1 h, and (iii) solution treatment (768 K for 1 h) plus aging at 468 K for 5 h. Texture analyses were performed using orientation distribution function (ODF) method. The texture strength after ECAP processing was different for the three samples in the order, solutionised > solutionised plus aged condition > as-received. The prominent texture components were A _E /[`(A)]<sub>E</sub> \bar{A}_{E} and B <sub>E</sub> /[`(B)]_E \bar{B}_{E} in addition to several weaker components for the three materials. The strong texture evolution in solutionised condition has been attributed to higher strain hardening of the matrix due to higher amount of solute. In case of the as-received as well as solutionised plus aged alloy, the weaker texture could be due to the strain scattering from extensive precipitate fragmentation and dissolution during ECAP.     

Influence of hot pressing temperature on the microstructure and mechanical properties of 75% Cu–25% Sn alloy

The alloy of 75% Cu–25% Sn was utilised and hot-pressed for 4 min at 421, 520 and 600 °C to obtain a self-sharpening bond for diamond honing stones at low sintering temperature. Densification and mechanical tests were performed, and structures were investigated by X-ray diffraction, energy dispersive spectroscopy and scanning electron microscopy. Results showed that the porous structures changed into microporous structures when the hot pressing temperature was increased from 421 °C to 600 °C. The mechanical properties improved from HRB 79.1 to HRB 105.1 in hardness and from 104.2 MPa to 201.4 MPa in transverse rupture strength. After hot pressing at 600 °C, the microstructure consisted of α(Cu) + δ eutectoid and micropores, which meets the requirements of bonds for honing stones.     

Dynamic ageing and the mechanical response of Al–Mg–Si alloy through equal channel angular pressing

In this paper, dynamic ageing characteristics associated with the application of equal channel angular pressing (ECAP) to Al6061 alloy at elevated temperatures was investigated. Followed by ECAP, Vickers microhardness measurement on the cross-sectional planes and microstructural observations were undertaken using transmission electron microscopy. The combination of the ECAP process with dynamic ageing at both 100 °C and 150 °C resulted in a significant increase in hardness. The grain size was measured as ∼160 nm after four passes. A comparison with the published data on the same alloy processed by ECAP at room temperature and statically aged, suggests several advantages in incorporating dynamic ageing with ECAP. These advantages consist of the ability to attain better grain refinement, increased hardness and the potential for saving time and energy.     

Microstructure and mechanical properties of equal channel angular pressed Mg–Y–RE–Zr alloy

The microstructure and mechanical properties of equal channel angular pressed (ECAP) Mg–Y–RE–Zr alloy (WE43) are examined. Results show that after ECAP, the average grain size remarkably decreases from ～50?µm at initial state to ～1.5?µm through ECAP for four passes and the homogeneity of microstructure also improves gradually. Meanwhile the secondary-phase β-Mg₅RE morphology has obvious transformation from plate-like to spherical. Moreover, the initial random texture is converted to the strong (0002) basal texture. The ultimate tensile strength and yield strength increase in all passes. However, the ductility exhibits a tendency of increase from 1 to 4 passes then decrease from 4 to 12 passes. The variation in strength and ductility is attributed to the effect of specific microstructure evolution.     

The application of equal channel angular pressing to join dissimilar metals,aluminium alloy and steel,using an Ag–Cu–Sn interlayer

Joining cylindrical and bar-shaped components manufactured from dissimilar materials is frequently required in various industrial applications. The current study focuses on developing equal channel angular pressing (ECAP) as a severe plastic deformation process for solid state joining of tubular aluminium alloy 6061 components and SAE 1018 steel rods. The influence of using a 0.1 mm thick 60Ag–30Cu–10Sn interlayer in addition to annealing at 220, 320, 420 and 520 °C for 60 min is investigated as well. Finite element analysis (FEA) is performed in order to evaluate the deformation behaviour of the workpieces during the ECAP joining process. XRD and EDX analyses as well as nanoindentation and shear tests are carried out to evaluate the joints' characteristics. The FEA outcomes show remarkable accumulation of equivalent plastic strain with relatively low strain inhomogeneity. Moreover, the experimental results indicate that with increasing annealing temperature, joint strength exhibits improvement as well. It is also revealed that the application of an interlayer at any specific annealing temperature leads to achieving higher shear strength values. According to the results, shear strength of up to 32 MPa is feasible by having an interlayer and with subsequent annealing at 520 °C.     

Influence of solutionising and aging temperatures on microstructure and mechanical properties of cast Al–Si–Cu alloy

Abstract

This paper presents the influence of solution and aging temperatures on the microstructure and mechanical properties of 319 secondary cast aluminium alloy. Experimental alloy was subjected to different heat treatment cycles. Heat treatments were designed with two solutionising temperatures (504 and 545°C) at two solutionising times (4 and 8 h), followed by quenching in water at 60°C and artificial aging. The artificial aging was carried out at two temperatures (200 and 154°C) for 6 h. The improvement in mechanical properties was obtained with low solution temperature (504°C) for 8 h followed by quenching in water to 60°C and aging at low temperature (154°C). The increase in the solutionising temperature from 504 to 545°C was recommendable only for short solutionising time (4 h). Increase in the aging temperature from 154 to 200°C has led to the increase in hardness with the corresponding decrease in ductility. Aging under unfavourable conditions (prolonged aging at high temperature) caused coarsening of spheroidised eutectic silicon crystals and precipitated particles resulted in deleterious effect on the tensile strength.     

Effect of Al on the microstructure and properties of Sn–0.7Cu solder alloy

Effect of Al on the microstructure and mechanical properties were investigated. The results showed that Al could depress the formation of eutectic phase in Sn–Cu–Al solder alloy. The intermetallic compounds of Sn–0.7Cu–0.03Al were refined compared with that of Sn–0.7Cu–0.015Al. Segregated CuAl intermetallic compound was observed in Sn–0.7Cu–0.15Al and Sn–0.7Cu–0.5Al solder alloy. Sn-whisker was observed on the polished surface of Sn–0.7Cu–0.15Al and Sn–0.7Cu–0.5Al. The ultimate tensile strength of Sn–0.7Cu–0.03Al and Sn–0.7Cu–0.5Al was found to be higher than that of Sn–0.7Cu–xAl (x = 0, 0.015 and 0.15). The elongation of Sn–0.7Cu–0.015Al was the highest. The creep performance of Sn–0.7Cu–0.03Al and Sn–0.7Cu–0.5Al was similar and higher than that of Sn–0.7Cu and Sn–0.7Cu–0.15Al.     

Influence of processing on the microstructure of Cu–8Cr–4Nb

The particle-strengthened Cu–8 at.%Cr–4 at.%Nb alloy is processed by consolidation of atomized powders followed by extrusion to obtain bars and rolling to produce sheets. Comparison of copper matrix grain and second-phase particle structures in both extruded and rolled Cu–8Cr–4Nb was performed. Extruded material displayed locally banded arrangements of Cr₂Nb particles, while the distribution of particles was more uniform in rolled material. Mean Cr₂Nb particle sizes were found to be essentially the same for both processing methods. Non-spherical particles in the extruded alloy showed some preferred orientation, whereas the rolled material displayed a more uniform particle orientation distribution. Extruded material exhibited a dual grain size distribution with smaller grains in banded regions. The mean grain size of 1.36 μm in extruded material was larger than the 0.65 μm grain size of rolled material. A [101] texture was evident in extruded material, whereas the rolled material was only slightly textured along the [001] and [111] directions. The processing differences for the rolled and extruded forms give rise to different microstructures and hence higher creep strength for the extruded material in the temperature range of 773–923 K.

---

Influence of retrogression and reaging on microstructure and properties of 8090 Al–Li alloy

Abstract

An investigation was made into the influence of a retrogression and reaging treatment on the microstructure, tensile properties, and stress corrosion cracking resistance of 8090 Al–Li alloy. The results show that retrogression of the material at 230°C for 40 min or 325°C for 1·5 min, and then reaging to the peak aged condition, can result in an improved combination of tensile strength and stress corrosion cracking resistance. Through retrogression and reaging treatment, the alloy almost achieves the strength of the peak aged state and the stress corrosion cracking resistance of the overaged state. Transmission electron microscopy indicates that the δ′ phase dissolves during retrogression and reprecipitates during reaging, thus increasing the strength. The T₂ phase precipitates and grows during both retrogression and reaging, which results in the increase of stress corrosion cracking resistance.

MST/1670     

Influence of sulphur on the microstructure and properties of Ag–Cu–Zn brazing filler metal

Abstract

The effect of sulphur on the microstructure and properties of Ag45–Cu30–Zn25 brazing filler metal was investigated. Under the given experimental conditions, the sulphuration products mainly consisted of CuS, ZnS, Ag₂S, Cu₂S and Ag₃CuS₂. These sulphides not only distributed on the surface but also diffused into the interior of the filler metal and cut apart the matrix thereby significantly damaging the tensile strength of the filler metal from 658 to 283 MPa. The corresponding fracture characterisation turned from ductile fracture to brittle fracture. The sulphides existed as solid particles, which hinder the spreading of the liquid filler metal and the spreading area dramatically decreased from 317?09 to 18?55 mm², which indicates that the filler metal rarely wets the base metal.     

Influence of the combined addition of Y and Nd on the microstructure and mechanical properties of Mg–Li alloy

Y and Nd are simultaneously added into Mg–5Li–3Al–2Zn alloy. It is found that there exist the phases of α-Mg, AlLi, Al₁₁Nd₃ and Al₂Y in the alloys. When the contents of Y and Nd are 1.2% and 0.8%, respectively, the grain is the finest with an average size of 30 μm, and the tensile strength of the alloy reaches 231 MPa, the elongation reaches 16%. When the ratio of Y to Nd is 1.2:0.8, there is a synergistic strengthening effect.     

Effect of integrated extrusion–equal channel angular pressing temperature on microstructural characteristics of low carbon steel

Abstract

In the present research, a combined forward extrusion–equal channel angular pressing was developed and executed for the deformation of a plain carbon steel. In this method, two different deformation steps, including forward extrusion and equal channel angular pressing, take place successively in a single die. The deformation process was performed at different deformation start temperatures (800, 930 and 1100°C). Three-dimensional finite element simulation was used to predict the strain and temperature variations within the samples during deformation. With microstructural observations and the results of finite element simulation, the main grain refinement mechanisms were studied at different deformation temperatures. The results show that the forward extrusion–equal channel angular pressing is effective in refining the ferrite grains from an initial size of 32 μm to a final size of ～0·9 μm. The main mechanisms of grain refinement were considered to be strain assisted transformation, dynamic strain induced transformation and continuous dynamic recrystallisation, depending on the deformation temperature.     

Effects of solution treatment on the microstructure and mechanical properties of Al–Cu–Mg–Ag alloy

The effects of solution treatment on the microstructure and mechanical properties of Al–Cu–Mg–Ag alloy were studied by optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), differential scanning calorimeter (DSC), transmission electron microscopy (TEM) and tensile test, respectively. The results show that the mechanical property increases and then decreases with increasing the solution temperature. And the residual phases are dissolved into the matrix gradually, the number fraction of the precipitation and the size of recrystallized grains increase. Compared to the solution temperature, the solution holding time has less effect on the microstructure and the mechanical properties of Al–Cu–Mg–Ag alloy. The overburnt temperature of Al–Cu–Mg–Ag alloy is 525 °C. The yield strength and the elongation get the best when the alloy is solution treated at 515 °C for 1.5 h, is 504 MPa and 12.2% respectively. The fracture mechanism of the samples is ductile fracture.     

Influence of Sc and Zr additions on microstructure and properties evolution of Al–Zn–Mg alloy

Journal of Materials Science - In this study, the effects of different Sc?+?Zr compound addition on the tensile properties, impact toughness, stress corrosion cracking (SCC) properties,...     

Effects of Cr,Mn, Si,Cu and Zr on microstructure and mechanical properties of high carbon Fe–16Al alloy

Abstract

Effects of alloying elements Cr, Mn, Si, Cu and Zr on the microstructure and mechanical properties of Fe₃Al (Fe–16Al) based alloy containing ～0·5 wt-%C have been investigated. Six alloys were prepared by a combination of air induction melting with flux cover and electroslag refining (ESR). ESR ingots were hot forged and hot rolled at 1373 K and were further characterised with respect to microstructure and mechanical properties. The base alloy and the alloys containing Cr, Mn, Si and Cu exhibit a two phase microstructure of Fe₃AlC_0·5 precipitates in Fe₃Al matrix whereas the alloy containing Zr exhibits a three phase microstructure, the additional phase being Zr rich carbide precipitates. Cr and Mn have high solubility in Fe₃AlC_0·5 precipitates as compared to Fe₃Al matrix whereas Cu and Si have very high solubility in Fe₃Al matrix compared to Fe₃AlC_0·5 precipitate and Zr has very low solubility in both Fe₃Al matrix and Fe₃AlC_0·5 precipitate. No significant improvement in room and high temperature (at 873 K) strengths was observed by addition of these alloying elements. Furthermore, it was observed that addition of these alloying elements has resulted in poor room and high temperature ductility. Addition of Cr, Mn, Si and Cu has resulted in marginal improvement in creep life, whereas Zr improved the creep life significantly from 22·3 to 117 h.     

The role of low-angle grain boundaries in multi-temperature equal channel angular pressing of Mg–3Al–1Zn alloy

Equal channel angular pressing was used to process an AZ31B magnesium alloy (nominally Mg–3Al–1Zn in wt%) at temperatures decreasing from 200 to 150 °C. The resulting microstructure was characterized by electron backscattered diffraction to reveal the role of low-angle grain boundaries in grain refinement. It was found that low-angle grain boundaries with misorientation angles lower than 5° are surrounded by regions of increased strain gradients, which can stimulate the generation of non-basal slip dislocations during the equal channel angular pressing at temperatures of approximately 150 °C. The strain gradients in the vicinity of the grain boundaries with misorientation angles in the range of 5°–10° were less frequent or were completely absent for high-angle grain boundaries with misorientation angles higher than 10°. This article also discusses the importance of low-angle grain boundaries for the generation of non-basal 〈c+a〉 dislocations needed for successful equal channel angular pressing of AZ31B at temperature of 150 °C.     

Grain refinement in as cast Al–Mg–Mn alloy during high temperature equal channel angular pressing

Abstract

An as cast Al–Mg–Mn alloy with coarse equiaxed grain structure was processed by equal channel angular pressing (ECAP) at 350°C up to eight passes. Systematic studies were made on the microstructural evolution during ECAP by optical microscopy, electron backscattered diffraction and TEM. Equal channel angular pressing led to a considerable grain refinement, resulting in an average cell size of about 1 μm and a fraction of high angle boundaries of 75% after eight pressing passes. Deformation bands were not developed during the ECAP process, and a reasonably equiaxed substructure was obtained even after one pass. The main mechanism of grain refinement was attributed to the continuous dynamic recrystallisation based on the motion of deformation induced dislocations. Discontinuous recrystallisation at grain boundaries and triple junctions also contributed to the refinement, which played an important role especially at high strain of eight passes.