Applicability of the various adsorption models of three dyes adsorption onto activated carbon prepared waste apricot

In this study, activated carbon (WA11Zn5) was prepared from waste apricot, which is waste in apricot plants in Malatya, by chemical activation with ZnCl(2). BET surface area of activated carbon is determined as 1060 m(2)/g. Activated carbon includes both micro and mesopores. Percentages of micropores and mesopores area are determined 36% and 74%, percentage of micropores and mesopores volume is 19% and 81%, respectively. The ability of WA11Zn5, to remove three dyes, methylene blue (MB), malachite green (MG), and crystal violet (CV), from effluent solutions by adsorption has been studied. The adsorption capacities of WA11Zn5 decreases in the order malachite green (MG)>methylene blue (MB)>crystal violet (CV). Equilibrium isotherms for the adsorption of three dyes on activated carbon were measured experimentally. Results were analyzed by the Langmiur, Freundlich, Dubinin-Redushkevich (D-R), Temkin, Frumkin, Harkins-Jura, Halsey and Henderson equation using linearized correlation coefficient at different temperature. The characteristic parameters for each isotherm have been determined. Models and the isotherm constant were evaluated depending on temperature. Langmiur and Frumkin equation is found to best represent the equilibrium data for three dye-WA11Zn5 systems.     

Kinetics of adsorption of dyes from aqueous solution using activated carbon prepared from waste apricot

Adsorbent (WA11Zn5) has been prepared from waste apricot by chemical activation with ZnCl(2). Pore properties of the activated carbon such as BET surface area, pore volume, pore size distribution, and pore diameter were characterized by N(2) adsorption and DFT plus software. Adsorption of three dyes, namely, Methylene Blue (MB), Malachite Green (MG), Crystal Violet (CV), onto activated carbon in aqueous solution was studied in a batch system with respect to contact time, temperature. The kinetics of adsorption of MB, MG and CV have been discussed using six kinetic models, i.e., the pseudo-first-order model, the pseudo-second-order model, the Elovich equation, the intraparticle diffusion model, the Bangham equation, the modified Freundlich equation. Kinetic parameters and correlation coefficients were determined. It was shown that the second-order kinetic equation could describe the adsorption kinetics for three dyes. The dyes uptake process was found to be controlled by external mass transfer at earlier stages (before 5 min) and by intraparticle diffusion at later stages (after 5 min). Thermodynamic parameters, such as DeltaG, DeltaH and DeltaS, have been calculated by using the thermodynamic equilibrium coefficient obtained at different temperatures and concentrations. The thermodynamics of dyes-WA11Zn5 system indicates endothermic process.     

β-carotene rejection mechanism from organic medium by using activated carbon produced from waste biomass apricot

The present paper deals with the study of adsorption of β-carotene in tetrahydrofuran solution on activated carbon. Activated carbon was prepared from apricot waste, which is a by-product of apricot processing by means of chemical activation with ZnCl₂. BET surface area of activated carbon was measured to be 1060 m² g^?1. The effect of adsorption time, percentage of activated carbon in β-carotene solution, and β-carotene concentration on adsorption efficiency was also determined. Results were analyzed by the Langmiur, Freundlich, Dubinin?Redushkevich (D-R), Temkin, Frumkin, Harkins?Jura, Halse, Henderson, and Henry isotherms with linearized correlation coefficient. The characteristic parameters for each isotherm have also been determined. The kinetics of β-carotene adsorption has been discussed by the pseudo-first-order model, the pseudo-second-order model, the Elovich equation, the intraparticle diffusion model, the Bangham equation, and the modified Freundlich equation. Three error analysis methods of residual mean square error (RMSE), chi-square statistic (χ²), and the average percentage error (% APE) have been used.     

Investigation kinetics mechanisms of adsorption malachite green onto activated carbon

Lignite was used to prepare activated carbon (T3K618) by chemical activation with KOH. Pore properties of the activated carbon such as BET surface area, pore volume, pore size distribution, and pore diameter were characterized by t-plot based on N2 adsorption isotherm. BET surface area of activated carbon is determined as 1000 m2/g. Adsorption capacity of malachite green (MG) onto T3K618 activated carbon was investigated in a batch system by considering the effects of various parameters like initial concentration (100, 150 and 200 mg/L) and temperature (25, 40 and 50 degrees C). The adsorption process was relatively fast and equilibrium was reached after about 20 min for 100, 150 mg/L at all adsorption temperature. Equilibrium time for 200 mg/L was determined as 20 min and 40 min at 298, 313 and 323 K, respectively. Simple mass and kinetic models were applied to the experimental data to examine the mechanisms of adsorption and potential rate controlling steps such as external mass transfer, intraparticle diffusion. Pseudo second-order model was found to explain the kinetics of MG adsorption most effectively. It was found that both mass transfer and pore diffusion are important in determining the adsorption rates. The intraparticle diffusion rate constant, external mass transfer coefficient, film and pore diffusion coefficient at various temperatures were evaluated. The activation energy (Ea) was determined as 48.56, 63.16, 67.93 kJ/mol for 100, 150, 200 mg/L, respectively. The Langmiur and Freundlich isotherm were used to describe the adsorption equilibrium studies at different temperatures. Langmiur isotherm shows better fit than Freundlich isotherm in the temperature range studied. The thermodynamic parameters, such as DeltaG degrees, DeltaS and DeltaH degrees were calculated. The thermodynamics of dyes-T3K618 system indicates endothermic process.     

Study to observe the applicability of the adsorption isotherms used for the adsorption of medicine organics onto activated carbon

In the present study, the activated carbon was prepared by chemically activating polymer waste under the influence of potassium hydroxide (KOH). The pore properties including the Brunauer–Emmett–Teller (BET) surface area, the volume of the pore, its size distribution, and average diameter were also characterized herein. The present study also evaluated the ability of the activated carbon to remove naproxen sodium, tannic acid, and caffeine from aqueous solutions through a process of adsorption. The equilibrium isotherms employed for the adsorption of drug organics onto the activated carbon were measured experimentally. The obtained results were analyzed by employing the Redlich–Peterson, Dubinin–Redushkevich, Temkin, Frumkin, Halsey, and Henderson equations by using a linearized correlation coefficient and statistically at varied temperatures. The models and the isotherm constants were evaluated based on the changes in the temperature. Among all, the Redlich–Peterson equation was determined to best represent the equilibrium data for the adsorption of naproxen sodium, and caffeine onto the activated carbon.     

The reuse of dried activated sludge for adsorption of reactive dye

Adsorption processes are alternative effective methods for removal of textile dyes from aqueous solutions. The adsorption ability of adsorbent affects by physico-chemical environment for this reason in this paper effect of initial pH, dye concentrations, temperature and dye hydrolyzation were determined in a batch system for removal of reactive dye by dried activated sludge. The Langmuir isotherm model was well described of adsorption reactive dye and maximum monolayer adsorption capacity (at pH 2) of activated sludge was determined as 116, 93 and 71mgg(-1) for 20 degrees , 35 degrees and 50 degrees C, respectively. Initial pH 2, 20 degrees C and 30min contact time are suitable for removal of reactive dyes from aqueous solutions. Activated sludge was characterized by FT-IR analysis and results showed that active sludge has different functional groups and functional groups of activated sludge are able to react with dye molecules in aqueous solution. The pseudo first-order, second-order and intraparticle diffusion kinetics were used to describe the kinetic data. The pseudo second-order kinetic model was fit well over the range of contact times and also an intra particle diffusion kinetic model was fit well but in the first 30min. The dye hydrolyzation was affected adsorption capacity of biomass and adsorption capacity of biomass decreased with dye hydrolyzation from 74 to 38mgg(-1).     

Chromium(VI) adsorption from aqueous solution by Hevea Brasilinesis sawdust activated carbon

Adsorption capacity of Cr(VI) onto Hevea Brasilinesis (Rubber wood) sawdust activated carbon was investigated in a batch system by considering the effects of various parameters like contact time, initial concentration, pH and temperature. Cr(VI) removal is pH dependent and found to be maximum at pH 2.0. Increases in adsorption capacity with increase in temperature indicate that the adsorption reaction is endothermic. Based on this study, the thermodynamic parameters like standard Gibb's free energy (DeltaG degrees ), standard enthalpy (DeltaH degrees ) and standard entropy (DeltaS degrees ) were evaluated. Adsorption kinetics of Cr(VI) ions onto rubber wood sawdust activated carbon were analyzed by pseudo first-order and pseudo second-order models. Pseudo second-order model was found to explain the kinetics of Cr(VI) adsorption most effectively. Intraparticle diffusion studies at different temperatures show that the mechanism of adsorption is mainly dependent on diffusion. The rate of intraparticle diffusion, film diffusion coefficient and pore diffusion coefficient at various temperatures were evaluated. The Langmuir, Freundlich and Temkin isotherm were used to describe the adsorption equilibrium studies of rubber wood sawdust activated carbon at different temperatures. Langmuir isotherm shows better fit than Freundlich and Temkin isotherm in the temperature range studied. The result shows that the rubber wood sawdust activated carbon can be efficiently used for the treatment of wastewaters containing chromium as a low cost alternative compared to commercial activated carbon and other adsorbents reported.     

Adsorption of 4-chlorophenol from aqueous solutions by xad-4 resin: isotherm, kinetic, and thermodynamic analysis

Removal of 4-chlorophenol (4-CP) from synthetic aqueous solutions through adsorption on Amberlite XAD-4 resin, a non-ionic macroreticular resins, under batch equilibrium experimental conditions at 298, 308 and 318K was investigated. It is necessary to propose a suitable model to a better understanding on the mechanism of 4-CP adsorption. For this purpose, Langmiur, Freundlich, Toth, and Redlich-Peterson (RP) isotherm models were compared. The two and three parameters in the adopted adsorption isotherm models were determined by the help of MATLAB package program. It was determined that best fitted adsorption isotherm models were obtained to be in the order: Redlich-Peterson>Langmuir>Toth>Freundlich isotherms. The pseudo-second-order kinetic model provided the best correlation to the experimental results. Results of the intra-particle diffusion model show that the pore diffusion is not the only rate limiting step. The lower correlation of the data to the Bangham's equation also represents that the diffusion of the adsorbate into pores of the sorbent is not the only rate-controlling step. The thermodynamic constants of adsorption phenomena; DeltaG degrees, DeltaH degrees, and DeltaS degrees were found as -4.17 (at 298K) kJ/mol, -42.01 kJ/mol, and -0.127 kJ/(mol K), respectively. The results showed that adsorption of 4-CP on Amberlite XAD-4, a nonionic polymeric resin was exothermic and spontaneous.     

Linear and non-linear regression analysis for the sorption kinetics of methylene blue onto activated carbon

Batch kinetic experiments were carried out for the sorption of methylene blue onto activated carbon. The experimental kinetics were fitted to the pseudo first-order and pseudo second-order kinetics by linear and a non-linear method. The five different types of Ho pseudo second-order expression have been discussed. A comparison of linear least-squares method and a trial and error non-linear method of estimating the pseudo second-order rate kinetic parameters were examined. The sorption process was found to follow a both pseudo first-order kinetic and pseudo second-order kinetic model. Present investigation showed that it is inappropriate to use a type 1 and type pseudo second-order expressions as proposed by Ho and Blanachard et al. respectively for predicting the kinetic rate constants and the initial sorption rate for the studied system. Three correct possible alternate linear expressions (type 2 to type 4) to better predict the initial sorption rate and kinetic rate constants for the studied system (methylene blue/activated carbon) was proposed. Linear method was found to check only the hypothesis instead of verifying the kinetic model. Non-linear regression method was found to be the more appropriate method to determine the rate kinetic parameters.     

Adsorption of methylene blue onto bamboo-based activated carbon: kinetics and equilibrium studies

Bamboo, an abundant and inexpensive natural resource in Malaysia was used to prepare activated carbon by physiochemical activation with potassium hydroxide (KOH) and carbon dioxide (CO(2)) as the activating agents at 850 degrees C for 2h. The adsorption equilibrium and kinetics of methylene blue dye on such carbon were then examined at 30 degrees C. Adsorption isotherm of the methylene blue (MB) on the activated carbon was determined and correlated with common isotherm equations. The equilibrium data for methylene blue adsorption well fitted to the Langmuir equation, with maximum monolayer adsorption capacity of 454.2mg/g. Two simplified kinetic models including pseudo-first-order and pseudo-second-order equation were selected to follow the adsorption processes. The adsorption of methylene blue could be best described by the pseudo-second-order equation. The kinetic parameters of this best-fit model were calculated and discussed.     

Comparison of the efficiency of palladium and silver nanoparticles loaded on activated carbon and zinc oxide nanorods loaded on activated carbon as new adsorbents for removal of Congo red from aqueous solution: Kinetic and isotherm study

The adsorption of Congo red (CR) into three new adsorbents including Palladium and silver nanoparticles loaded on activated carbon (Pd NPs-AC, Ag NPs-AC) and zinc oxide nanorods loaded on activated carbon (ZnO-NRs-AC) in a batch method has been studied following the optimization of effective variables including pH, amount of adsorbents and time. The experimental data was fitted to conventional kinetic models including the pseudo first-order and second-order Elovich and intraparticle diffusion model and based on calculated respective parameters such as rate constants, equilibrium adsorption capacities and correlation coefficients. It was found that for all adsorbents the removal process follows the pseudo second other kinetic model with involvement of interparticle diffusion model. The experimental isotherm data were analyzed using the Langmuir, Freundlich, Tempkin and Dubinin and Radushkevich equations and it was found for all adsorbents that the removal process followed the Langmuir isotherm.     

Equilibrium and kinetic data and process design for adsorption of Congo Red onto bentonite

The adsorption of Congo Red onto bentonite in a batch adsorber has been studied. Four kinetic models, the pseudo first- and second-order equations, the Elovich equation and the intraparticle diffusion equation, were selected to follow the adsorption process. Kinetic parameters; rate constants, equilibrium adsorption capacities and correlation coefficients, for each kinetic equation were calculated and discussed. It was shown that the adsorption of Congo Red onto bentonite could be described by the pseudo second-order equation. The experimental isotherm data were analyzed using the Langmuir, Freundlich and Temkin equations. Adsorption of Congo Red onto bentonite followed the Langmuir isotherm. A single stage batch adsorber was designed for different adsorbent mass/treated effluent volume ratios using the Langmuir isotherm.     

Dye adsorption on unburned carbon: kinetics and equilibrium

Unburned carbon in fly ash is an important by-product from coal combustion. In this investigation, unburned carbon has been separated from fly ash and been employed as a low cost adsorbent for a basic dye adsorption (Rhodamine B) in aqueous solution. Adsorption isotherm and kinetics of adsorption have been investigated using batch experiments. It is found that dye adsorption capacity depends on initial concentration, pH of solution, and temperature. The adsorption isotherm can be described by Langmuir model and the adsorption capacity of Rhodamine B at 30, 40, and 50 degrees C can reach 9.7 x 10(-5), 1.14 x 10(-4), and 1.5 x 10(-4)mol g(-1), respectively. The pseudo first- and second-order kinetic models have been employed to fit the dynamic adsorption. It is found that the dynamic adsorption follows the pseudo second-order model. Thermodynamic calculations indicate that the adsorption is endothermic reaction with DeltaH degrees at 25 kJ mol(-1).     

Preparation and evaluation of cerium(IV) tungstate powder as inorganic exchanger in sorption of cobalt and europium ions from aqueous solutions

Cerium(IV) tungstate powder was chemically synthesized and exploited as adsorbent material for the decontamination study of cobalt and europium ions from radioactive waste solutions under simulated conditions using batch technique. The influences of pH, particle size and temperature have been reported. The uptake of europium was found to be slightly greater than that of cobalt and the apparent sorption capacity increases with increase in temperature. Thermodynamic parameters such as changes in Gibbs free energy (DeltaG degrees), enthalpy (DeltaH degrees), and entropy (DeltaS degrees) were calculated. The numerical value of DeltaG degrees decreases with an increase in temperature, indicating that the sorption reaction of each ion was spontaneous and more favorable at higher temperature. The positive values of DeltaH degrees correspond to the endothermic nature of sorption processes and suggested that chemisorption was the predominant mechanism. A comparison of kinetic models applied to the sorption rate data of each ion was evaluated for the pseudo first-order, the pseudo second-order, intraparticle diffusion and homogeneous particle diffusion kinetic models. The results showed that both the pseudo second-order and the homogeneous particle diffusion models were found to best correlate the experimental rate data. The numerical values of the rate constants and particle diffusion coefficients were determined from the graphical representation of the proposed models. Activation energy (E(a)) and entropy (DeltaS++) of activation were also computed from the linearized form of Arrhenius equation.     

Removal of chromium(VI) from aqueous solution by activated carbons: kinetic and equilibrium studies

The objective of this study is to assess the uptake of hexavalent chromium (Cr(VI)) from aqueous solutions onto activated carbons (AC) produced from wood. Two activated carbons are tested, a KOH-activated carbon and a commercial H3PO4-activated carbon (Acticarbone CXV). The adsorption of Cr(VI) is maximal at the lowest values of pH (pH 3) and increases with temperature for both adsorbents. The KOH-activated carbon shows higher capacity for adsorption of Cr(VI) than Acticarbone. The sorption isotherms fit the Langmuir model accurately. The adsorption reaction was found to obey a pseudo second-order rate. The activation energy and the pre-exponential factor as well as the thermodynamic functions related to adsorption reaction, DeltaS degrees , DeltaH degrees , DeltaG degrees , were determined. Nevertheless, the global reaction rate is probably controlled by the intra-particular diffusion of Cr(VI) and the mass diffusivity of Cr(VI) was evaluated.     

Contact time optimization of two-stage batch adsorber design using second-order kinetic model for the adsorption of phosphate onto alunite

The adsorption of phosphate onto alunite in a batch adsorber has been studied. Four kinetic models including pseudo first- and second-order equation, intraparticle diffusion equation and the Elovich equation were selected to follow the adsorption process. Kinetic parameters, rate constants, equilibrium adsorption capacities and related correlation coefficients, for each kinetic model were calculated and discussed. It was shown that the adsorption of phosphate onto alunite could be described by the pseudo second-order equation. Adsorption of phosphate onto alunite followed the Langmuir isotherm. A model has been used for the design of a two-stage batch adsorber based on pseudo second-order adsorption kinetics. The model has been optimized with respect to operating time in order to minimize total operating time to achieve a specified amount of phosphate removal using a fixed mass of adsorbent. The results of two-stage batch adsorber design studies showed that the required times for specified amounts of phosphate removal significantly decreased. It is particularly suitable for low-cost adsorbents/adsorption systems when minimising operating time is a major operational and design criterion, such as, for highly congested industrial sites in which significant volume of effluent need to be treated in the minimum amount of time.     

Adsorption of reactive dye onto carbon nanotubes: equilibrium, kinetics and thermodynamics

The adsorption efficiency of carbon nanotubes for Procion Red MX-5B at various pHs and temperatures was examined. The amount adsorbed increased with the CNTs dosage; however, the adsorption capacity initially increased with the CNTs dosage (<0.25 g/l) and then declined as the CNTs dosage increased further (>0.25 g/l). The linear correlation coefficients and standard deviations of Langmuir and Freundlich isotherms were determined and the results revealed that Langmuir isotherm fitted the experimental results well. Kinetic analyses were conducted using pseudo first- and second-order models and the intraparticle diffusion model. The regression results showed that the adsorption kinetics were more accurately represented by a pseudo second-order model. Changes in the free energy of adsorption (DeltaG degrees ), enthalpy (DeltaH degrees ) and entropy (DeltaS degrees), as well as the activation energy (E(a)) were determined. DeltaH degrees and DeltaS degrees were 31.55 kJ/mol and 216.99J/molK, respectively, at pH 6.5 and 41.47 kJ/mol and 244.64 J/molK at pH 10. The activation energy was 33.35 kJ/mol at pH 6.5. DeltaH degrees, DeltaG degrees and E(a) all suggested that the adsorption of Procion Red MX-5B onto CNTs was by physisorption.     

Adsorption of a cationic dye (methylene blue) onto spent activated clay

The adsorption characteristics of methylene blue (MB) onto spent activated clay (SAC), a waste produced from an edible oil manufacturer was investigated. Results showed that the adsorption increased with increasing MB concentration, temperature, and pH. The adsorption equilibrium data was well fitted by multilayer adsorption isotherm. The maximum adsorption capacities for MB ranged from 0.94x10(-4) to 3.41x10(-4)mol/g between 5 and 45 degrees C. Thermodynamic parameters suggest that the adsorption is spontaneous and endothermic. We proposed a modified double exponential equation accounting both with chemical and mathematical point of view to describe the adsorption kinetic data. The increases of mass transfer and adsorption capacity were mainly attributed to the interlayer of the SAC expanding at higher temperature. An activation energy of 13.5 kcal/Kmol was determined suggesting that the adsorption involved a chemical reaction mechanism.     

An environmentally friendly process; adsorption of radionuclide Tl-201 on fibrous waste tea

This work presents an investigation of the adsorption of the radionuclide of Tl-201 from waste water on the fibrous tea factory waste. The experimental parameters were chosen as temperature, pH, stirring speed, adsorbent dose and nominal particle size in the ranges of 10.0-40.0 degrees C, 2.0-10.0, 300-720 rpm, 1.0-15.0 g/L and 0.15-0.71 mm, respectively. The most effective parameter on the adsorption yield was found to be pH of the solution. Fourier transforms infrared and electron paramagnetic resonance spectroscopy studies were performed for the characterisation of the adsorption on tea waste. The experimental data were found to be in good agreement with the isotherm models of Freundlich, Halsey, Handerson and Dubinin-Radushkevich. Thermodynamic analysis showed that the values of Delta G and Delta H are negative. It was obtained that the adsorption rate can be represented very well by second-order pseudo homogeneous kinetic model. All the results proved that fibrous tea plant waste makes an excellent adsorbent for Tl-201 radionuclide.     

An adsorption study of Al(III) ions onto chitosan

The adsorption of Al(III) from aqueous solutions onto chitosan was studied in a batch system. The isotherms and the kinetics of adsorption with respect to the initial Al(III) concentration and temperature were investigated. Langmuir and Freundlich adsorption models were applied to describe the experimental isotherms. Equilibrium data fitted very well to the Langmuir model in the entire concentration range (5-40 mg/L). The negative values of free energy (DeltaG degrees ) and enthalpy (DeltaH degrees ) for the adsorption of Al(III) onto chitosan indicated that the adsorption process is a spontaneous and exothermic one. Two simplified kinetic models, based on pseudo first-order and pseudo second-order equations, were tested to describe the adsorption mechanism. The pseudo second-order kinetic model resulted in an activation energy of 56.4 kJ/mol. It is suggested that the overall rate of Al(III) ion adsorption is likely to be controlled by the chemical process. The values of the enthalpy (DeltaH(#)) and entropy (DeltaS(#)) of activation were 53.7 kJ/mol and -164.4 J/molK, respectively. The free energy of activation (DeltaG(#)) at 30 degrees C was 103.5 kJ/mol.