Properties of surface‐modified multiwalled carbon nanotube filled poly(ethylene terephthalate) composite films

Poly(ethylene terephthalate) (PET)/multiwalled carbon nanotube (MWCNT) composites were prepared by in situ polymerization. To improve the dispersion of MWCNTs in the PET matrix, functionalized MWCNTs having acid groups (acid‐MWCNTs) and acetic groups (acetic‐MWCNTs) on their surfaces were used. The functional groups were confirmed by infrared spectrometry. Scanning electron microscopy showed that acetic‐MWCNTs had a better dispersion in the PET matrix than pristine MWCNTs and acid‐MWCNTs. A reaction between PET and acetic‐MWCNTs was confirmed by a shift of the Raman G band to a higher frequency and an increase of the complex viscosity in the rheological properties. The composites containing functionalized MWCNTs showed a large increase in their tensile strengths and moduli. The values of the strengths and moduli of the PET/acetic‐MWCNT composites were higher than those of the PET/acid‐MWCNT composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Preparation of microcellular poly(ethylene terephthalate) and its properties

Engineering plastics poly(ethylene terephthalate) (PET) is relatively difficult to process microcellularly compared to general thermal plastics because of its low melting viscosity. A new method was developed to microcellularly process PET in this study with a general hydraulic press above PET's crystallization temperature and below its melting temperature within times of a few minutes. A processing window existed in which to prepare microcellular PET under certain foaming time, pressure, temperature, and foaming reagent content scope. The effects of foaming time, temperature, pressure, and foaming reagent content on the thermal, mechanical, and dynamic mechanical thermal properties of microcellular PET foam were investigated. Differential scanning calorimetry (DSC) analysis showed that the transition temperature and crystallinity of microcellular PET had small changes with increasing foaming time. Under some processing conditions used in this study, the tensile strength and breaking extension of microcellular PET foam were both increased at the same time, indicating strengthening and toughening effects. The variation of storage modulus, loss modulus, and tan δ under dynamic mechanical thermal analysis was in accord with DSC analysis and mechanical measurements. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1956–1962, 2003     

Synthesis and characterization of poly(ethylene isophthalate‐co‐ethylene terephthalate) copolyesters

Poly(ethylene isophthalate‐co‐ethylene terephthalate) (PEIPET) copolymers of various compositions and molecular weights were synthesized by melt polycondensation and characterized in terms of chemical structure and thermal and rheological properties. At room temperature, all copolymers were amorphous and thermally stable up to about 400°C. The main effect of copolymerization was a monotonic increase of glass transition temperature (T_g) as the content of ethylene terephthalate units increased. The Fox equation accurately describes the T_g–composition data. The presence of ethylene terephthalate units was found to influence rheological behavior in the melt, with the Newtonian viscosity increasing as the content of ethylene terephthalate units increased. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 186–193, 2004     

Mechanical,thermal and electrical properties of multi‐walled carbon nanotube/aluminium nitride/polyetherimide nanocomposites

A series of polyimide‐based nanocomposites containing polyimide‐grafted multi‐walled carbon nanotubes (PI‐g MWCNTs) and silane‐modified ceramic (aluminium nitride (AlN)) were prepared. The mechanical, thermal and electrical properties of hybrid PI‐g MWCNT/AlN/polyetherimide nanocomposites were investigated. After polyimide grafting modification, the PI‐g MWCNTs showed good dispersion and wettability in the polyetherimide matrix and imparted excellent mechanical, electrical and thermal properties. The utilization of the hybrid filler was found to be effective in increasing the thermal conductivity of the composites due to the enhanced connectivity due to the high‐aspect‐ratio MWCNT filler. The use of spherical AlN filler and PI‐g MWCNT filler resulted in composite materials with enhanced thermal conductivity and low coefficient of thermal expansion. Results indicated that the hybrid PI‐g MWCNT and AlN fillers incorporated into the polyetherimide matrix enhanced significantly the thermal stability, thermal conductivity and mechanical properties of the matrix. Copyright © 2012 Society of Chemical Industry     

Development,optimization, and characterization of electrospun poly(lactic acid) nanofibers containing multi‐walled carbon nanotubes

Electrospinning of poly (L ‐D ‐lactic acid) (PLA) was investigated with the addition of multi‐walled carbon nanotubes (MWNT) for development of a scaffold for tissue engineering. Through this experiment, it was determined that the optimal concentration of PLA with weight average molecular weight (M_w) 250,000 g/mol is ～20 wt % as indicated by scanning electron microscopy. This concentration produces fibers with no beading or film formation. The preferred solvent system is a combination of chloroform and dimethyl formamide to alleviate the volatile action of chloroform. The optimum processing parameters for PLA are an electric field of 1 kV/cm which was determined by a surface response plot to minimize fiber diameter based on the applied voltage, working distance, and addition of MWNT. Fourier Transform infrared spectroscopy has indicated the removal of the solvent system. With the addition of MWNT, the fiber diameter was drastically reduced by 70% to form fibers with a mean diameter of 700 nm. This is believed to be due to an increased surface charge density for the MWNT/polymer solution. Transmission electron microscopy validated the alignment of the MWNT within the fibers. MWNT loading exhibited an increase in the conductance of the scaffold and the tensile modulus at an optimal loading level of 0.25 wt %. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Interface adjustment between poly(ethylene terephthalate) and graphene oxide in order to enhance mechanical and thermal properties of nanocomposites

There is great interest in the use of graphene and derivatives in the production of polymer nanocomposites as it provides improvements in the properties of the materials to which they are associated. Such improvements depend heavily on filler dispersion and the interaction between the nanomaterials and the matrix. This work aimed to study the compatibility of graphene oxide (GO) with a poly(ethylene terephthalate) matrix. For this, graphite was modified using Hummers method, using reaction times of 3 and 6 h. The obtained GO was functionalized with amine, amide, and magnetite groups (FGO). The effects of the oxidation degree, functionalization and concentration of the nanofillers on the dispersion and consequently on the properties of the polymer nanocomposites were evaluated. The nanocomposites were synthesized by the solid–solid deposition method followed by the melt mixing technique. It was observed that lower concentrations of nanofiller associated with the lower degree of oxidation and functionalization improved the interaction of the nanofillers with the matrix, which resulted in better mechanical properties under tensile stresses for strain at break, maximum stress, Young's modulus and toughness. It was also observed that the glass transition and crystallization of nanocomposites increased due to a nucleating effect of the nanofillers.     

Processing and properties of carbon nanotube/poly(methyl methacrylate) composite films

A systematic study of the reinforcement of single‐walled carbon nanotubes (SWNTs), multiwalled carbon nanotubes, and vapor‐grown carbon nanofibers (VGCNFs) in poly(methyl methacrylate) (PMMA) is reported. SWNT/PMMA composite films with various SWNT concentrations (from 0.5 to 50 wt % with respect to the weight of PMMA) were processed from nitromethane. Two types of SWNTs were used: SWNT‐A, which contained 35 wt % metal catalyst, and SWNT‐B, which contained about 2.4 wt % metal catalyst. Properties of different nanotubes containing composites were compared with 15 wt % carbon nanotubes (CNTs). Property enhancement included electrical conductivity, mechanical properties, and solvent resistance. The thermal degradation of PMMA in the presence of CNTs in air and nitrogen environments was studied. No variation in the thermal degradation behavior of PMMA/CNT was observed in nitrogen. The peak degradation temperature increased for the composites in air at low CNT loadings. Dynamic and thermomechanical properties were also studied. At a 35 wt % SWNT loading, a composite film exhibited good mechanical and electrical properties, good chemical resistance, and a very low coefficient of thermal expansion. Property improvements were rationalized in terms of the nanotube surface area. Composite films were also characterized with Raman spectroscopy. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Impact,thermal, and morphological properties of functionalized rubber toughened‐poly(ethylene terephthalate) nanocomposites

In this study, poly(ethylene terephthalate)/organo‐montmorillonite (PET/OMMT) nanocomposites were melt‐compounded using twin screw extruder followed by injection molding. Maleic anhydride grafted styrene‐ethylene/butylene‐styrene (SEBS‐g‐MAH) was used to improve the impact properties of the PET/OMMT nanocomposites. The notched and un‐notched impact strength of PET/OMMT nanocomposites increased at about 2.5 times and 5.5 times by the addition of 5 wt % of SEBS‐g‐MAH. Atomic force microscopy (AFM) scans were taken from the polished surface of both PET/OMMT and SEBS‐g‐MAH toughened PET/OMMT nanocomposites. The addition of SEBS‐g‐MAH altered the phase structure and clay dispersion in PET matrix. It was found that some of the OMMT silicate layers were encapsulated by SEBS‐g‐MAH. Further, the addition of SEBS‐g‐MAH decreased the degree of crystallinity of the PET/OMMT nanocomposites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Nanocomposites based on poly(butylene adipate‐co‐terephthalate) and montmorillonite

Nanocomposites based on biodegradable poly(butylene adipate‐co‐terephthalate) (PBAT) and layered silicates were prepared by the melt intercalation method. Nonmodified montmorillonite (MMT) and organo‐modified MMTs (DA‐M, ODA‐M, and LEA‐M) by the protonated ammonium cations of dodecylamine, octadecylamine, and N‐lauryldiethanolamine, respectively, were used as the layered silicates. The comparison of interlayer spacing between clay and PBAT composites with inorganic content 3 wt % measured by X‐ray diffraction (XRD) revealed the formation of intercalated nanocomposites in DA‐M and LEA‐M. In case of PBAT/ODA‐M (3 wt %), no clear peak related to interlayer spacing was observed. From morphological studies using transmission electron microscopy, the ODA‐M was found to be finely and homogeneously dispersed in the matrix polymer, indicating the formation of exfoliated nanocomposite. When ODA‐M content was increased, the XRD peak related to intercalated clay increased. Although the exfoliated ODA‐M (3 wt %) nanocomposite showed a lower tensile modulus than the intercalated DA‐M and LEA‐M (3 wt %) composites, the PBAT/ODA‐M composite with inorganic content 5 wt % showed the highest tensile modulus, strength, and elongation at break among the PBAT composites with inorganic content 5 wt %. Their tensile properties are discussed in relation to the degree of crystallinity of the injection molded samples. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 386–392, 2005     

Effect of rolling deformation on the structures and properties of multi‐walled carbon nanotube filled isotactic polypropylene

Isotactic polypropylene filled with various contents of multi‐walled carbon nanotubes (MWCNTs) were fabricated by the injection molding technique and then rolled at room temperature. The unrolled samples (URS) and rolled samples (RS) were characterized by X‐ray diffraction studies, scanning electron microscopy, mechanical and micromechanical tests and differential thermal analyses. Although the URS exhibit the lamellar α‐crystal with a*‐axis orientation, the RS show the same crystals with both a*‐ and c‐axis orientation, which is explained by interlamellar and intralamellar slips and lamellar destruction. Scanning electron micrographs display distinct surface morphological features for both URS and RS. While the tensile strength of RS is higher than that of URS, the Young's modulus (Y) is found to be lower than that of URS. Anisotropy in microharness (H) parallel and perpendicular to the rolled direction has been detected, although H for both samples increases with increasing MWCNT contents. The average relationship H/Y ≈ 0.18 as estimated for URS is closer to the predicted value of 0.10 for polymers than the H/Y ≈ 0.22 obtained for RS. The lamellar thickness for URS increases with increase of MWCNT content and that for RS decreases, as evaluated from both differential thermal analyses and X‐ray diffraction data. Copyright © 2011 Society of Chemical Industry     

Preparation and properties of poly(ethylene terephthalate)/inorganic whiskers composites

To improve the crystallization and mechanical properties of poly(ethylene terephthalate) (PET), in this work, PET/SiO₂‐MgO‐CaO whiskers composites were prepared via in situ polymerization. The morphology, crystallization, and mechanical properties of the prepared composites were investigated. It was found that inorganic whiskers could be easily dispersed in PET matrix, as demonstrated by SEM and PLM. DSC and PLM observation indicated a strong nucleation capability of inorganic whiskers for PET. Mechanical analysis results showed that the glass transition temperature, tensile strength, and modulus of the composites were greatly improved. A possible chemical bonding between PET chains and the surface of whiskers was observed by FTIR, TGA, and sedimentation experiment. It could be the main reason for the good dispersion and improved properties of the prepared composites. This work is important for the application of PET due to the low cost but high reinforcing efficiency of this inorganic whisker. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermal and mechanical properties of plasticized poly(L‐lactide) nanocomposites with organo‐modified montmorillonites

Nanocomposites of poly(lactide) (PLA) and the PLA plasticized with diglycerine tetraacetate (PL‐710) and ethylene glycol oligomer containing organo‐modified montmorillonites (ODA‐M and PGS‐M) by the protonated ammonium cations of octadecylamine and poly(ethylene glycol) stearylamine were prepared by melt intercalation method. In the X‐ray diffraction analysis, the PLA/ODA‐M and plasticized PLA/ODA‐M composites showed a clear enlargement of the difference of interlayer spacing between the composite and clay itself, indicating the formation of intercalated nanocomposite. However, a little enlargement of the interlayer spacing was observed for the PLA/PGS‐M and plasticized PLA/PGS‐M composites. From morphological studies using transmission electron microscopy, a finer dispersion of clay was observed for PLA/ODA‐M composite than PLA/PGS‐M composite and all the composites using the plasticized PLA. The PLA and PLA/PL‐710 composites containing ODA‐M showed a higher tensile strength and modulus than the corresponding composites with PGS‐M. The PLA/PL‐710 (10 wt %) composite containing ODA‐M showed considerably higher elongation at break than the pristine plasticized PLA, and had a comparable tensile modulus to pure PLA. The glass transition temperature (T_g) of the composites decreased with increasing plasticizer. The addition of the clays did not cause a significant increase of T_g. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Preparation and characterization of graphene/poly(vinyl alcohol) nanocomposites

Graphene (GE)‐based nanocomposites are emerging as a new class of materials that hold promise for many applications. In this article, we present a general approach for the preparation of GE/poly(vinyl alcohol) (PVA) nanocomposites. The basic strategy involved the preparation of graphite oxide from graphite, complete exfoliation of graphite oxide into graphene oxide sheets, followed by reduction to GE nanosheets, and finally, the preparation of the GE/PVA nanocomposites by a simple solution‐mixing method. The synthesized products were characterized by X‐ray diffraction, field emission scanning electron microscopy, Fourier transform infrared spectroscopy, thermogravimetry, and differential scanning calorimetry analysis. The GE nanosheets were well dispersed in the PVA matrix, and the restacking of the GE sheets was effectively prevented. Because of the strong interfacial interaction between PVA and GE, which mainly resulted from the hydrogen‐bond interaction, together with the improvement in the PVA crystallinity, the mechanical properties and thermal stability of the nanocomposites were obviously improved. The tensile strength was increased from 23 MPa for PVA to 49.5 MPa for the nanocomposite with a 3.25 wt % GE loading. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation and characterization of magnetic nanofibers with iron oxide nanoparticles and poly(ethylene terephthalate)

Iron oxide nanoparticle/Poly(ethylene terephthalate) (PET) nanowebs were obtained by electrospinning. To achieve superparamagnetic properties, iron oxide nanoparticles with diameters below 25 nm were used. Diameter distribution of iron oxide nanoparticles was measured by a particle size analyzer. Iron oxide nanoparticles were added into 16 wt % PET solution in the ratio of 5, 10, and 15 wt % to PET. The morphology of iron oxide nanoparticle/PET nanowebs was observed using field emission-scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). The nanofiber diameter increased as increasing iron oxide nanoparticle concentration. The superparamagnetic behavior of iron oxide nanoparticle/PET nanofiber was confirmed using superconducting quantum interference device (SQUID). The degree of crystallinity of iron oxide nanoparticle/PET nanowebs was calculated from a differential scanning calorimeter (DSC) results. The change of flexural rigidity and tensile properties of electrospun iron oxide nanoparticle/PET nanowebs with the external magnetic field were examined ISO 9073-7 testing method, universal testing machine and an appropriate magnet. Also, the elastic modulus of iron oxide nanoparticle/PET nanofiber was measured using nanoindentation. With applying magnetic field, the improvement in mechanical properties of field-responsive magnetic nanofibers and nanowebs was confirmed. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Efficient method for recycling poly(ethylene terephthalate) to poly(butylene terephthalate) using transesterification reaction

A method of recycling postconsumer poly(ethylene terephthalate (PET) using transesterification was studied. Shredded flakes of postconsumer PET waste were transesterified with higher diols, such as 1,4‐butanediol, 1,4‐cyclohexane dimethanol, and 1,6‐hexanediol, to yield copolyesters in the presence of Ti(iPrO)₄ and Sb₂O₃ as catalysts. The extent of the formation of undesirable tetrahydrofuran side products was dependent on the molar ratio of PET to1,4‐butanediol and the time of reflux during transesterification. Quantitative insertion of the butylene moiety into PET could be achieved under appropriate reaction conditions. The mechanical properties of PBT obtained by a transesterification reaction of PET with 1,4‐butanediol were comparable to those of virgin PBT (obtained by direct reaction of dimethyl terephathalate with 1,4‐butanediol). © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3720–3729, 2004     

Preparation and characterization of multi‐walled carbon nanotubes/polymer gradient composite films

BACKGROUND: Recently, much work has focused on the efficient dispersion of carbon nanotubes (CNTs) throughout a polymer matrix for mechanical and/or electrical enhancement. However, there are still only few reports about gradient distribution of CNTs in polymer matrices. In the work reported here, CNTs embedded in a polymer film with a gradient distribution were successfully obtained and studied. RESULTS: For composite films with gradient distributions of CNTs, the upper surface behaves as an intrinsic insulator, while the lower one behaves as a semiconductor, or even as a conductor. It is also found that with an increase of 1 wt% CNTs, the resistance of the bottom surface decreases by 2–3 orders of magnitude, as compared with pure polyarylene ether nitrile; furthermore, when the proportion of CNTs increases up to 5 wt%, the resistance of the bottom surface shows only very little change. As a result, sufficient matrix conductivity of the bottom surface could be achieved at a lower filler concentration with CNTs in a gradient distribution. Meanwhile, the thermal stability, glass transition temperature and tensile properties of the matrix are maintained. CONCLUSION: There is considerable interest in such gradient composite films, which could be applied in the electrical engineering, electronics and aerospace fields, for their excellent mechanical properties, thermal stability and novel electrical properties. Copyright © 2008 Society of Chemical Industry     

Nanocomposites based on poly(ϵ‐caprolactone) and the montmorillonite treated with dibutylamine‐terminated ϵ‐caprolactone oligomer

Dibutylamine‐terminated ε‐caprolactone oligomers (CLOs: CLOL, CLOM, and CLOH) with number–averaged molecular weight (M_n), 500, 1300, and 2200, respectively, were synthesized by the ring‐opening polymerization of ε‐caprolactone initiated by 2‐(dibutylamino)ethanol in the presence of tin(II) 2‐ethylhexanoate. Nanocomposites based on poly(ε‐caploractone) (PCL) and the caprolactone oligomer‐treated montmorillonites (CLO‐Ms: CLOL‐M, CLOM‐M, and CLOH‐M) were prepared by melt intercalation method. The XRD and TEM analyses of the PCL composites revealed that the extent of exfoliation of the clay platelets increased with increasing molecular weight of the used CLOs. Tensile strength and modulus of the PCL/CLO‐M composites increased with increasing molecular weight of the CLO and increasing inorganic content. The tensile modulus of the PCL/CLOH‐M nanocomposite with inorganic content 5.0 wt % was three times higher than that of control PCL. Among the PCL/CLO‐M composites, the PCL/CLOM‐M composite had the highest crystallization temperature and melting temperature. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Sequence analysis and fiber properties of a blend of poly(ethylene terephthalate) and poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)

Blends of poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate‐co‐4,4′‐ bibenzoate) (PETBB) are prepared by coextrusion. Analysis by ¹³C‐NMR spectroscopy shows that little transesterification occurs during the blending process. Additional heat treatment of the blend leads to more transesterification and a corresponding increase in the degree of randomness, R. Analysis by differential scanning calorimetry shows that the as‐extruded blend is semicrystalline, unlike PETBB15, a random copolymer with the same composition as the non‐ random blend. Additional heat treatment of the blend leads to a decrease in the melting point, T_m, and an increase in glass transition temperature, T_g. The T_m and T_g of the blend reach minimum and maximum values, respectively, after 15 min at 270°C, at which point the blend has not been fully randomized. The blend has a lower crystallization rate than PET and PETBB55 (a copolymer containing 55 mol % bibenzoate). The PET/PETBB55 (70/30 w/w) blend shows a secondary endothermic peak at 15°C above an isothermal crystallization temperature. The secondary peak was confirmed to be the melting of small and/or imperfect crystals resulting from secondary crystallization. The blend exhibits the crystal structure of PET. Tensile properties of the fibers prepared from the blend are comparable to those of PET fiber, whereas PETBB55 fibers display higher performance. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1793–1803, 2004     

Preparation,characterization and properties of a halogen‐free phosphorous flame‐retarded poly(butylene terephthalate) composite based on a DOPO derivative

A phosphorous flame retardant (DOPO‐MAH) was synthesized through the reaction between of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) and maleic anhydride (MAH) and confirmed by FT‐IR, ¹H NMR, and ³¹P NMR techniques. The obtained flame retardant was then melt blended with poly(butylene terephthalate) (PBT) to prepare flame retardant PBT/DOPO‐MAH composites. The composites were characterized by LOI, UL‐94, and mechanical tests as well as scanning electron microscopy, thermogravimetric analysis, and differential scanning calorimetry analysis. On adding 20 wt % DOPO‐MAH, LOI increased from 20.9 to 25.7 and the UL‐94 V‐0 rating was achieved, whereas the tensile and flexural properties were notably improved. Torque‐time profile during the melt blending and intrinsic viscosity of the composite indicated that DOPO‐MAH acted as both flame retardant and chain extender for the PBT matrix. The results showed that PBT/DOPO‐MAH composite is a promising material for its good comprehensive properties. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1301‐1307, 2013     

Linear thermoelastic characterization of anisotropic poly(ethylene terephthalate) films

All nine independent elastic constants have been determined for a biaxially stretched poly(ethylene terephthalate) (PET) film using novel mechanical methods. The orthotropic directions and the in‐plane Poisson's ratios were first characterized using vibrational holographic interferometry of tensioned membrane samples. The out‐of‐plane Poisson's ratio was obtained by measuring the change in tension with the change in pressure for constant strain conditions. Pressure–volume–temperature (PVT) equipment was used to measure the bulk compressibility as well as the volumetric thermal expansion coefficient (TEC). The in‐plane Young's moduli were obtained by tensile tests, while the out‐of‐plane modulus was calculated from the compressibility and other elastic constants that describe the in‐plane behavior. The in‐plane TECs in the machine and transverse directions were determined using a thermal mechanical analyzer (TMA). The out‐of‐plane TEC was determined using these values and the volumetric TEC determined via PVT. The resulting compliance matrix satisfies all of the requirements of a positive‐definite energy criterion. The procedure of characterization utilized in this article can be applied to any orthotropic film. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2937–2947, 2002