Effect of sputtering power and annealing temperature on the properties of indium tin oxide thin films prepared from radio frequency sputtering using powder target

Indium tin oxide (ITO) thin films were deposited on quartz substrates by radio frequency (RF) sputtering with different RF power (100–250 W) using the powder target at room temperature. The effect of sputtering power on their structural, electrical and optical properties was systematically investigated. The intensity of (400) orientation clearly increases with the sputtering power increases, although the films have (222) preferred orientation. Increasing sputtering power is benefit for lower resistivity and transmittance. The films were annealed at different temperature (500–800 °C), then we explored the relationship between their electro-optical and structural properties and temperature. It has been observed that the annealed films tend to have (400) orientation and then show the lower resistivity and transmittance. The ITO thin film prepared by RF sputtering using powder target at 700 °C annealing temperature and 200 W sputtering power has the resistivity of 2.08 × 10^?4 Ω cm and the transmittance of 83.2 %, which specializes for the transparent conductive layers.     

Microstructure and properties of Al-doped ZnO thin films by nonreactive DC magnetron sputtering at room temperature following rapid thermal annealing

A series of Al-doped ZnO (AZO) thin films deposited by nonreactive DC magnetron sputtering at room temperature following rapid thermal annealing was studied to examine the influence of these Al doping concentration, sputtering power and annealing temperature on their microstructure, electrical and optical transport properties. AZO thin films with Al dopant of 3 wt% were oriented more preferentially along the (002) direction, bigger grain size and lower electrical resistivity The resistivity of AZO films decreases with the increase of Al content from 1 to 3 wt%, sputtering power from 60 to 100 W and the annealing temperature from 50 to 250 °C. Sputtering power and annealing had some effect on the average transmittance of AZO thin films. For AZO thin films with Al doping level of 3 wt%, the lowest electrical resistivity of 5.3 × 10⁻⁴ Ω cm and the highest optical transmittance of 88.7% could gain when the sputtering power was 100 W and the annealing temperature was 200 °C or above.     

溅射功率对AZO透明导电薄膜的影响

采用射频磁控溅射法在玻璃衬底上沉积了AZO透明导电薄膜,并用原子力显微镜观测了薄膜表面形貌,XRD测试了薄膜相结构和单色仪测试了薄膜透射率。结果表明,制备的薄膜具有高度c轴择优取向性,其表面平整,晶粒均匀致密。当溅射功率为180W、溅射气体流量为15sccm、基片温度为200℃时制得的薄膜方阻为10Ω/□,在可见光区平均透射率大于85%。     

Preparation and properties of surface textured ZnO: Al films by direct current pulse magnetron sputtering

Transparent conductive surface textured Al-doped zinc oxide (ZnO:Al, AZO) thin films were prepared on glass substrates by direct current pulse magnetron sputtering at substrate temperature of 270 °C and post-etching in NaOH solution at room temperature. The effects of Ar flow rate on the structural, optical, electrical properties and light trapping ability were investigated systematically. With the increasing of Ar flow rate from 10 to 50 sccm, different surface features ranging from honeycomb-like to crater-like structures were observed. The relationship between surface textured structures and Ar flow rate was discussed. The AZO film deposited with Ar flow rate in 50 sccm displayed fine optoelectronic properties, improved figure of merit and effective surface textured structures for light trapping, which could be applied as a transparent conducting electrode in silicon-based thin film solar cells.     

The properties of Al doped ZnO thin films deposited on various substrate materials by RF magnetron sputtering

Transparent conductive Al-doped ZnO (AZO) thin films were deposited on various substrates including glass, polyimide film (PI) and stainless steel, using radio frequency magnetron sputtering method. The structural, electrical and optical properties of AZO thin films grown on various substrates were systematically investigated. We observe that substrate materials play important roles in film crystallization and resistivity but little on optical transmittance. X-ray diffractometer study shows that all obtained AZO thin films have wurtzite phase with highly c-axis preferred orientation, and films on glass present the strongest (002) diffraction peaks. The presence of compression stress plays critical role in determining the crystalline structure of AZO films, which tends to stretch the lattice constant c and enlarge the (002) diffraction angle. Although the films on the glass present the finest electrical properties and the resistivity reaches 12.52 × 10-4 Ωm, AFM study manifests that films on flexible substrates, especially stainless steel, bestrew similar inverted pyramid structure which are suitable for window material and electrode of solar cells. The average optical transmittance of AZO thin films deposited on glass and PI are both around 85% in the visible light range (400–800 nm).     

Influence of RF power on structural,morphology, electrical,composition and optical properties of Al-doped ZnO films deposited by RF magnetron sputtering

In this study, influence of RF power on the structural, morphology, electrical, composition and optical properties of Al-doped ZnO (ZnO:Al) films deposited by RF magnetron sputtering have been investigated. Films were systematically and carefully investigated by using variety of characterization techniques such as low angle X-ray diffraction, UV–visible spectroscopy, Raman spectroscopy, Hall measurement, X-ray photoelectron spectroscopy, field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy etc. Low angle X-ray diffraction analysis showed that the films are polycrystalline with hexagonal wurtzite structure and which was further confirmed by Raman spectroscopy analysis. Its preferred orientation shifts from (102) to (002) with increase in RF power. The average grain size was found in the range of 15–21 nm over the entire range of RF power studied. The FE-SEM analysis showed that grain size and surface roughness of ZnO:Al films increase in with increase in RF power. The UV–visible spectroscopy analysis revealed that all films exhibit transmittance >85 % in the visible region. The optical band gap increases from 3.37 to 3.85 eV when RF power increased from 75 to 225 W. Hall measurements showed that the minimum resistivity has been achieved for the film deposited at 200 W. The improvement in the electrical properties may attribute to increase in the carrier concentration and Hall mobility. Based on the experimental results, the RF power of 200 W appears to be an optimum sputtering power for the growth of ZnO:Al films. At this optimum sputtering power ZnO:Al films having minimum resistivity (8.61 × 10^?4 Ω-cm), highly optically transparent (~87 %) were obtained at low substrate temperature (60 °C) at moderately high deposition rate (22.5 nm/min). These films can be suitable for the application in the flexible electronic devices such as TCO layer on LEDs, solar cells, TFT-LCDs and touch panels.     

The characteristics of transparent conducting Al-doped zinc oxide thin films deposited on polymer substrates

Al-doped zinc oxide (AZO) transparent, conductive thin films were deposited on inexpensive polyethylene terephthalate substrates, using radio frequency (rf) magnetron sputtering, with an AZO ceramic target (the Al₂O₃ content is approximately 2 wt%). This paper presents an effective method for the optimization of the parameters for the deposition process for AZO thin films with multiple performance characteristics, using the Taguchi method, combined with grey relational analysis. Using the Taguchi quality design concept, an L₉ orthogonal array was chosen for the experiments. The effects of various process parameters (rf power, substrate-to-target distance, substrate temperature and deposition time) on the electrical, structural, morphological and optical properties of AZO films were investigated. In the confirmation runs, using grey relational analysis, the electrical resistivity of the AZO films was found to have decreased from 5.0?×?10^?3 to 1.6?×?10^?3?Ω-cm and the optical transmittance was found to have increased from 74.39 to 79.40%. The results demonstrate that the Taguchi method combined with grey relational analysis is an economical way to obtain the multiple performance characteristics of AZO films with the fewest experimental data. Additionally, by applying an Al buffer layer, of thickness 10?nm, the results show that the electrical resistivity was 3.1?×?10^?4?Ω-cm and the average optical transmittance, in the visible part of the spectrum, was approximately 79.12%.     

Deposition of Al-doped ZnO films on polyethylene naphthalate substrate with radio frequency magnetron sputtering

100 nm Al-doped ZnO (AZO) thin films were deposited on polyethylene naphthalate (PEN) substrates with radio frequency magnetron sputtering using 2 wt.% Al-doped ZnO target at various deposition conditions including sputtering power, target to substrate distance, working pressure and substrate temperature. When the sputtering power, target to substrate distance and working pressure were decreased, the resistivity was decreased due to the improvement of crystallinity with larger grain size. As the substrate temperature was increased from 25 to 120 °C, AZO films showed lower electrical resistivity and better optical transmittance due to the significant improvement of the crystallinity. 2 wt.% Al-doped ZnO films deposited on glass and PEN substrates at sputtering power of 25 W, target to substrate distance of 6.8 cm, working pressure of 0.4 Pa and substrate temperature of 120 °C showed the lowest resistivity (5.12 × 10^− 3 Ω cm on PEN substrate, 3.85 × 10^− 3 Ω cm on glass substrate) and high average transmittance (> 90% in both substrates). AZO films deposited on PEN substrate showed similar electrical and optical properties like AZO films deposited on glass substrates.     

Effects of sputtering pressure and Al buffer layer thickness on properties of AZO films grown by rf magnetron sputtering

Transparent and conductive Al-doped (2 wt.%) zinc oxide (AZO) films were deposited on inexpensive soda-lime glass substrates by using rf magnetron sputtering at room temperature. This study analyzed the effects of argon sputtering pressure, which varied in the range from 0.46 to 2.0 Pa, on the morphological, electrical and optical properties of AZO films. The only (0 0 2) diffraction peak of the film were observed at 2θ～34.45°, exhibiting that the AZO films had hexagonal ZnO wurtzite structure, and a preferred orientation with the c-axis perpendicular to the substrate. By applying a very thin aluminum buffer layer with the thickness of 2 nm, findings show that the electrical resistivity was 9.46 × 10⁻⁴ Ω-cm, and the average optical transmittance in the visible part of the spectra was approximately 81%. Furthermore, as for 10 nm thick buffer layer, the electrical resistivity was lower, but the transmittance was decreased.     

PET纤维基AZO透明导电薄膜溅射工艺参数的优化

室温下,结合正交实验表,用射频磁控溅射在涤纶(PET)非织造布基材上生长AZO(Al2O3:ZnO)纳米结构薄膜.采用四探针测量仪测试AZO薄膜的方块电阻,用原子力显微镜(AFM)分析薄膜微结构;通过正交分析法对实验L9(33)AZO薄膜的性能指标进行分析.实验结果表明:溅射厚度对AZO薄膜导电性能起主导作用,其次为氩气压强和溅射功率;同时,得出制备AZO薄膜的最佳工艺为:溅射功率150W、厚度100m和气压0.2Pa,该参数下样品的方块电阻为1.633×103Ω,AZO纳米颗粒的平均直径约为69.4nm.     

Effect of ZnO buffer layer on AZO film properties and photovoltaic applications

Aluminum-doped ZnO (AZO) transparent conducting films were deposited on glass substrates with and without intrinsic ZnO (i-ZnO) buffer layers by a home made and low cost radio-frequency (RF) magnetron sputtering system at room temperature in pure argon ambient and under a low vacuum level. The films were examined and characterized for electrical, optical, and structural properties for the application of CIGS solar cells. The influence of sputter power, deposition pressure, film thickness and residual pressure on electrical and optical properties of layered films of AZO, i-ZnO and AZO/i-ZnO was investigated. The optimization of coating process parameters (RF power, sputtering pressure, thickness) was carried out. The effects of i-ZnO buffer layer on AZO films were investigated. By inserting thin i-ZnO layers with a thickness not greater than 125 nm under the AZO layers, both the carrier concentration and Hall mobility were increased. The resistivity of these layered films was lower than that of single layered AZO films. The related mechanisms and plasma physics were discussed. Copper indium gallium selenide (CIGS) thin film solar cells were fabricated by incorporating bi-layer ZnO films on CdS/CIGS/Mo/glass substrates. Efficiencies of the order of 7–8% were achieved for the manufactured CIGS solar cells (4–5 cm² in size) without antireflective films. The results demonstrated that RF sputtered layered AZO/i-ZnO films are suitable for application in low cost CIGS solar cells as transparent conductive electrodes.     

利用脉冲直流磁控溅射制备ZnO:Al薄膜的研究

利用中频脉冲直流磁控溅射法制备了平面ZnO:Al(AZO)透明导电薄膜,研究了沉积压力、衬底温度和溅射功率对AZO薄膜光电性能、薄膜稳定性的影响.结果表明:在较低沉积压力、衬底温度及溅射功率下,可获得具有低电阻率、高透过率、高稳定性的AZO薄膜.     

Study of optoelectronics and microstructures on the AZO/nano-layer metals/AZO sandwich structures

In this study, growth nano-layer metals (Al, Cu, Ag) and Al-doped ZnO (AZO) thin films are deposited on glass substrates as the transparent conducting oxides (TCOs) to form AZO/nano-layer metals/AZO sandwich structures. The conductivity properties of thin films are enhanced when the average transmittance over the wavelengths 400–800 nm is maintained at higher than 80 %. A radio frequency magnetron sputtering system is used to deposit the metal layers and AZO thin films of different thickness, to form AZO/Al/AZO (ALA), AZO/Cu/AZO (ACA) and AZO/Ag/AZO (AGA) structures. X-ray diffraction and field emission scanning electron microscopy are used to analyze the crystal orientation and structural characteristic. The optical transmission and resistivity are measured by UV–VIS–NIR spectroscopy and Hall effect measurement system, respectively. The results show that when the Ag thickness is maintained at approximately 9 nm, the TCOs thin film has the lowest resistivity of 8.9 × 10^?5 Ω-cm and the highest average transmittance of 81 % over the wavelengths 400–800 nm. The crystalline Ag nano-crystal structures are observed by high-resolution transmission electron microscopy. In addition, the best figure of merit for the AZO/Ag/AZO tri-layer film is 2.7 × 10^?2 (Ω^?1), which is much larger than that for other structures.     

Quality enhancement of AZO thin films at various thicknesses by introducing ITO buffer layer

Due to the simultaneously superior optical transmittance and low electrical resistivity, transparent conductive electrodes play a significant role in semiconductor electronics. To enhance the electrical properties of these films, one approach is thickness increment which degrades the optical properties. However, a preferred way to optimize both electrical and optical properties of these layers is to introduce a buffer layer. In this work, the effects of buffer layer and film thickness on the structural, electrical, optical and morphological properties of AZO thin films are investigated. Al-doped zinc oxide (AZO) is prepared at various thicknesses of 100 to 300 nm on the bare and 100 nm-thick indium tin oxide (ITO) coated glass substrates by radio frequency sputtering. Results demonstrate that by introducing ITO as a buffer layer, the average values of sheet resistance and strain within the film are decreased (about 76 and 3.3 times lower than films deposited on bare glasses), respectively. Furthermore, the average transmittance of ITO/AZO bilayer is improved nearly 10% regarding single AZO thin film. This indicates that bilayer thin films show better physical properties rather than conventional monolayer thin films. As the AZO film thickness increases, the interplanar spacing, d₍₀₀₂₎, strain within the film and compressive stress of the film in the hexagonal lattice, decreases indicating the higher yield of AZO crystal. Moreover, with the growth in film thickness, carrier concentration and optical band gap (E_g) of AZO film are increased from 4.62?×?10¹⁹ to 8.21?×?10¹⁹ cm^?3 and from 3.55 to 3.62 eV, respectively due to the Burstein-Moss (BM) effect. The refractive index of AZO thin film is obtained in the range of 2.24–2.26. With the presence of ITO buffer layer, the AZO thin film exhibits a resistivity as low as 6?×?10^?4 Ω cm, a sheet resistance of 15 Ω/sq and a high figure of merit (FOM) of 1.19?×?10⁴ (Ω cm)^?1 at a film thickness of 300 nm. As a result, the quality of AZO thin films deposited on ITO buffer layer is found to be superior regarding those grown on a bare glass substrate. This study has been performed over these two substrates because of their significant usage in the organic light emitting diodes and photovoltaic applications as an enhanced carrier injecting electrodes.     

Effects of substrate temperatures on the thermal stability of Al-doped ZnO thin films grown by DC magnetron sputtering

In this work, Al-doped (4 at%) ZnO(AZO) thin films were prepared by DC magnetron sputtering using a home-made ceramic target at different substrate temperatures. The microstructure, optical, electrical and thermal stability properties of these thin films were characterized systematically using scanning electron microscopy, UV–Vis-NIR spectrometry, X-ray diffraction, and Hall measurements. It was observed that the AZO thin films deposited at 350 °C exhibited the lowest resistivity of 5.76 × 10⁻⁴ Ω cm, high average visible transmittance (400–800 nm) of 92%, and the best thermal stability. Comparing with the AZO thin films deposited at low substrate temperatures, the AZO thin films deposited at 350 °C had the highest compact surface morphology which could hinder the chemisorbed and diffused oxygen. This was considered to be the main mechanism which was responsible for the thermal degradation of AZO thin films.     

Low-temperature preparation of transparent conductive Al-doped ZnO thin films by a novel sol–gel method

We developed a novel sol–gel method to prepare transparent conductive Al-doped ZnO (AZO) thin film at low temperature. The AZO nanocrystals were prepared by a solvothermal method and then they were dispersed in the monoethanolamine and methanol to form AZO colloids. A (002)-oriented ZnO thin film was used as a nucleation layer to induce the (002)-oriented growth of AZO thin films. The AZO thin films were prepared on Si(100) and fused quartz glass substrates with the (002)-oriented ZnO nucleation layer and annealed at 400 °C for 60 min. All AZO thin films showed (002) orientation. For electrical and optical measurements, the films deposited on glass substrates were post-annealed at 400 °C for 30 min in forming gas (100 % H₂) to improve their conductivity. These samples had high transparency in the visible wavelength range, and also showed good conductivity. A 0.2 mol L^?1 AZO solution with 3 at.% Al content was heated in a Teflon autoclave at 160 °C for 30 min to form AZO nanocrystals, and then the AZO nanocrystals were suspended in the MEA and methanol to obtain the stable AZO colloid. The Al content in the AZO nanocrystals was 2.7 at.%, and the high Al doping coefficient was mainly attributed to the formation of AZO nanocrystals in the autoclave. The AZO thin film using this colloid had the lowest resistivity of 3.89 × 10^?3 Ω cm due to its high carrier concentration of 3.29 × 10²⁰ cm^?3.     

Thickness dependent properties of nickel oxide thin films deposited by dc reactive magnetron sputtering

Nickel oxide thin films of various thicknesses were grown on glass substrates by dc reactive magnetron sputtering technique in a pure oxygen atmosphere with sputtering power of 150 W and substrate temperature of 523 K. Crystalline properties of NiO films as a function of film thickness were investigated using X-ray diffraction. XRD analysis revealed that (200) is the preferred orientation and the orientation of the films changed from (200) to (220) at film thickness of 350 nm. The maximum optical transmittance of 60% and band gap of 3.82 eV was observed at the film thickness of 350 nm. The lowest electrical resistivity of 5.1 Ω cm was observed at a film thickness of 350 nm, thereafter resistivity increases with film thickness.     

Transparent and conductive ZnO:Al thin films grown by pulsed magnetron sputtering in current or voltage regulation modes

Aluminium-doped zinc oxide (AZO) thin films have been prepared by pulsed magnetron sputtering from a ceramic oxide target in pure argon atmosphere. Sputtering processes were performed in current or voltage regulation modes at different pulsing frequencies up to 200 kHz. Several growth parameters (discharge power, substrate temperature and growth rate) as well as AZO film properties (crystalline structure, optical transmittance and electrical characteristics) have been measured and analysed as a function of the current or voltage applied, the pulsing frequency and the operation time. By adjusting these deposition parameters, AZO layers with resistivity as low as 1.0×10⁻³ Ωcm and average visible transmittance above 85% have been obtained at growth rate in the range 70-80 nm/min, at substrate temperatures below 150 °C.     

Transparent conductive and infrared reflective AZO/Cu/AZO multilayer film prepared by RF magnetron sputtering

AZO/Cu/AZO multilayer films were prepared on glass substrate by radio frequency magnetron sputtering technology. The prepared films were investigated by a four-point probe system, X-ray diffraction, optical transmittance spectra, scanning electron microscope, atomic force microscopy and Fourier transform infrared spectroscopy. The results showed that Cu inner layer started forming a continuous film at the thickness around 11 nm. The prepared AZO/Cu/AZO samples exhibited the visible transmittance of 60–80 % and sample with 15 nm Cu inner layer showed the highest infrared reflection rate of 67 % in FIR region and the lowest sheet resistance of 16.6 Ω/sq. The proper visible transmittance and infrared reflection property of the AZO/Cu/AZO multilayer film make it a promising candidate for future energy conservation materials.     

Preparation of ZnO:Al thin film on transparent TPT substrate at room temperature by RF magnetron sputtering technique

Aluminum doped ZnO thin films (ZnO:Al) deposited on flexible substrates are suitable to be used as transparent conductive oxide (TCO) thin films in solar cells because of the excellent optical and electrical properties. TPT films are a kind of composite materials and are usually used as encapsulation material of solar panels. In this paper, ZnO:Al film was firstly deposited on transparent TPT substrate by RF magnetron sputtering. The structural, optical, and electrical properties of the film were investigated by X-ray diffractometry (XRD), scanning electron microscope (SEM), UV–visible spectrophotometer, as well as Hall Effect Measurement System. Results revealed that the obtained film had a hexagonal structure and a highly preferred orientation with the c-axis perpendicular to the substrate. Also, the film showed a high optical transmittance over 80% in the visible region and a resistivity of about 3.03 × 10^? 1 Ω·cm.