Development of Ni catalysts for tar removal by steam gasification of biomass

Catalytic performance of Ni/CeO₂/Al₂O₃ catalysts prepared by a co-impregnation and a sequential impregnation method in steam gasification of real biomass (cedar wood) was investigated. Especially, Ni/CeO₂/Al₂O₃ catalysts prepared by the co-impregnation method exhibited higher performance than Ni/Al₂O₃ and Ni/CeO₂/Al₂O₃ prepared by the sequential impregnation method, and the catalysts gave lower yields of coke and tar, and higher yields of gaseous products. The Ni/CeO₂/Al₂O₃ catalysts were characterized by thermogravimetric analysis, temperature-programmed reduction with H₂, transmission electron microscopy and extended X-ray absorption fine structure, and the results suggested that the interaction between Ni and CeO₂ became stronger by the co-impregnation method than that by sequential method. Judging from both results of catalytic performance and catalyst characterization, it is found that the intimate interaction between Ni and CeO₂ can play very important role on the steam gasification of biomass.     

Experimental Study on Catalytic Biomass Gasification in a Bubbling Fluidized Bed

A bubbling fluidized‐bed gasification system was selected for catalytic steam gasification of rice straw with four Ni‐based catalysts, i.e., Ni/Al₂O₃, Ni/CeO₂, Ni/MnO₂, and Ni/MgO. The effect of temperature, steam/biomass ratio (S/B), and catalyst/biomass ratio (C/B) on the gas composition, char conversion, and hydrogen yield was evaluated. It was found that higher temperature and S/B promote hydrogen production and char conversion. The results also demonstrated that the catalytic activity of Ni/Al₂O₃ under different S/B values is better than those of the other catalysts. Regarding the catalyst activity, all four catalysts exhibited good performance in terms of tar removal and carbon conversion. However, the performance of Ni/Al₂O₃ was superior to that of the other three catalysts.     

Promoting effect of the interaction between Ni and CeO2 on steam gasification of biomass

Catalytic performance of Ni/CeO₂/Al₂O₃ catalysts prepared by a co-impregnation method was higher than that of Ni/CeO₂/Al₂O₃ by a sequential impregnation method and Ni/Al₂O₃ in steam gasification of biomass in terms of the yield of coke and tar. Characterization by means of temperature programmed reduction suggests that the intimate interaction between Ni and CeO₂ on the Ni/CeO₂/Al₂O₃ by the co-impregnation method can be related to high performance in steam gasification of biomass.     

Catalytic Steam Reforming of Propane over Ni/LaAlO<Subscript>3</Subscript> Catalysts: Influence of Preparation Methods and OSC on Activity and Stability

Abstract  

To develop an efficient catalyst for steam reforming of propane, Ni/LaAlO₃ catalysts were prepared by deposition precipitation, impregnation, and solvo-thermal methods, and characterized by XRD, BET, H₂-TPR, elemental analyses, and TEM. Ni/Al₂O₃ and Ni/CeO₂ catalysts were also synthesized by the solvo-thermal method for comparison. The Ni/LaAlO₃ catalysts exhibited better catalytic performance than both Ni/Al₂O₃ and Ni/CeO₂ catalysts, and activities with Ni/LaAlO₃ were found to be dependent upon the preparation methods. In particular, the Ni/LaAlO₃ catalyst synthesized by the solvo-thermal method exhibited the highest activity presumably because tetrahydrofuran helps distribute generated Ni nanoparticles onto the catalyst surface in a uniform fashion. In addition, the solvo-thermally prepared Ni/LaAlO₃ catalyst was found to be highly stable, with its activity being maintained at least during 100 h. The observed high stability is attributed to the excellent oxygen storage capacity of LaAlO₃, which was first determined by thermogravimetric methods as well as by soot oxidations in the presence of Al₂O₃, CeO₂, and LaAlO₃. Compared to the Ni/Al₂O₃ and Ni/CeO₂ catalysts, Ni/LaAlO₃ exhibited suppressed carbon formation even at lower S/C ratios due to the superior oxygen transport ability of the LaAlO₃ support.     

Thermal ageing phenomena and strategies towards reactivation of NO x - storage catalysts

The thermal ageing and reactivation of Ba/CeO₂ and Ba/Al₂O₃ based NO _x -storage/ reduction (NSR) catalysts was studied on model catalysts and catalyst systems at the engine. The mixed oxides BaAl₂O₄ and BaCeO₃, which lower the storage activity, are formed during ageing above 850 °C and 900 °C, respectively. Interestingly, the decomposition of BaCeO₃ in an atmosphere containing H₂O/NO₂ leads again to NO _x -storage active species, as evidenced by comparison of fresh, aged and reactivated Pt-Ba/CeO₂ based model catalysts. This can be technically exploited, particularly for the Ba/CeO₂ catalysts, as reactivation studies on thermally aged Ba/CeO₂ and Ba/Al₂O₃ based NSR catalysts on an engine bench showed. An on-board reactivation procedure is presented, that improved the performance of a thermally aged catalyst significantly.     

Promoting effect of Pt addition to Ni/CeO2/Al2O3 catalyst for steam gasification of biomass

The modification of Ni/CeO₂/Al₂O₃ with Pt can make the activation by H₂ reduction unnecessary, and this indicates that the Pt/Ni/CeO₂/Al₂O₃ catalyst can be activated automatically by the compounds contained in tar. This can be explained by the enhancement of the Ni reducibility by the addition of Pt. The results of the temperature programmed reduction with H₂ also support this enhancement. Furthermore, the addition of 0.1% Pt to Ni/CeO₂/Al₂O₃ (4 wt% Ni, 30 wt% CeO₂) enhanced the performance in the steam gasification of biomass, compared to Ni/Al₂O₃ and Ni/CeO₂/Al₂O₃ in terms of low tar yield and high gas yield. This can be related to the Pt–Ni alloy formation indicated by the extended X-ray absorption fine structure analysis.     

Hydrogen production by steam gasification of polypropylene with various nickel catalysts

Several nickel-based catalysts (Ni/Al₂O₃, Ni/MgO, Ni/CeO₂, Ni/ZSM-5, Ni-Al, Ni-Mg-Al and Ni/CeO₂/Al₂O₃) have been prepared and investigated for their suitability for the production of hydrogen from the two-stage pyrolysis–gasification of polypropylene. Experiments were conducted at a pyrolysis temperature of 500 °C and gasification temperature was kept constant at 800 °C with a catalyst/polypropylene ratio of 0.5. Fresh and reacted catalysts were characterized using a variety of methods, including, thermogravimetric analysis, scanning electron microscopy with energy dispersive X-ray spectrometry and transmission electron microscopy. The results showed that Ni/Al₂O₃ was deactivated by two types of carbons (monoatomic carbons and filamentous carbons) with a total coke deposition of 11.2 wt.% after reaction, although it showed to be an effective catalyst for the production of hydrogen with a production of 26.7 wt.% of the theoretical yield of hydrogen from that available in the polypropylene. The Ni/MgO catalyst showed low catalytic activity for H₂ production, which might be due to the formation of monoatomic carbons on the surface of the catalyst, blocking the access of gaseous products to the catalyst. Ni-Al (1:2) and Ni-Mg-Al (1:1:2) catalysts prepared by co-precipitation showed good catalytic abilities in terms of both H₂ production and prevention of coke formation. The ZSM-5 zeolite with higher surface area was also shown to be a good support for the nickel-based catalyst, since, the Ni/ZSM-5 catalyst showed a high rate of hydrogen production (44.3 wt.% of theoretical) from the pyrolysis–gasification of polypropylene.     

Bi-metallic catalysts of mesoporous Al2O3 supported on Fe,Ni and Mn for methane decomposition: Effect of activation temperature

Methane decomposition reaction has been studied at three different activation temperatures (500 °C, 800 °C and 950 °C) over mesoporous alumina supported Ni–Fe and Mn–Fe based bimetallic catalysts. On co-impregnation of Ni on Fe/Al₂O₃ the activity of the catalyst was retained even at the high activation temperature at 950 °C and up to 180 min. The Ni promotion enhanced the reducibility of Fe/Al₂O₃ oxides showing higher catalytic activity with a hydrogen yield of 69%. The reactivity of bimetallic Mn and Fe over Al₂O₃ catalyst decreased at 800 °C and 950 °C activation temperatures. Regeneration studies revealed that the catalyst could be effectively recycled up to 9 times. The addition of O₂ (1 ml, 2 ml, 4 ml) in the feed enhanced substantially CH₄ conversion, the yield of hydrogen and the stability of the catalyst.     

Effect of CeO<Subscript>2</Subscript>-addition sequence on the performance of CeO<Subscript>2</Subscript>-modified Ni/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst in autothermal reforming of iso-octane

Two types of CeO₂-modified Ni/Al₂O₃ catalysts were prepared by a consecutive impregnation method with different sequences in the impregnation of Ni and CeO₂, and their performance in autothermal reforming (ATR) of isooctane was investigated. Catalysts prepared by adding CeO₂ prior to the addition of Ni, Ni/CeO₂-Al₂O₃, produced larger amounts of hydrogen than those obtained using catalysts prepared by adding the two components in an opposite sequence, Ni-CeO₂/Al₂O₃. The results of H₂ chemisorption and temperature-programmed reduction revealed that added CeO₂ increased the dispersion of the Ni species on Al₂O₃ and suppressed the formation of NiAl₂O₄ in the catalyst such that large amounts of Ni species were present as NiO, the active species for the ATR. The elemental and thermogravimetric analyses of deactivated catalysts indicated that Ni/CeO₂-Al₂O₃, which showed a longer lifetime than Ni-CeO₂/Al₂O₃, contained lesser amounts and different types of coke on the surface.     

Highly Active and Selective Nickel–Platinum Catalyst for the Low Temperature Hydrogenation of Maleic Anhydride to Succinic Anhydride and Synthesis of Succinic Acid at 40 °C

Abstract  

PtNi bimetallic and Ni monometallic catalysts supported on HY–Al₂O₃, HX–Al₂O₃, ZSM-5–Al₂O₃, USY–Al₂O₃, Beta–Al₂O₃ and Al₂O₃ were prepared and evaluated for the hydrogenation of maleic anhydride in the temperature range of 40–150 °C. Results from flow reactor studies showed that supports strongly affected the catalytic properties of different bimetallic and monometallic catalysts. The results showed that the HY–Al₂O₃ support exhibited the highest activity and selectivity. Using NiPt/Al₂O₃–HY catalyst and performing the reaction, it was possible to carry out the lowest reaction temperature ever carried at 100% conversion. Adding a small amount of Pt (0.5) to the Ni (5%)/Al₂O₃–HY catalyst that is effective for increasing the selectivity and activity. We also found that PtNi is an efficient catalyst for the one-pot conversion of maleic acid into succinic acid with 100% conversion at 40 °C.     

Selective Production of H2 from Ethanol at Low Temperatures over Rh/ZrO2–CeO2 Catalysts

A series of Rh catalysts on various supports (Al₂O₃, MgAl₂O₄, ZrO₂, and ZrO₂–CeO₂) have been applied to H₂ production from the ethanol steam reforming reaction. In terms of ethanol conversion at low temperatures (below 450 °C) with 1wt% Rh catalysts, the activity decreases in the order: Rh/ZrO₂–CeO₂ > Rh/Al₂O₃ > Rh/MgAl₂O₄ > Rh/ZrO₂. Support plays a very important role on product selectivity at low temperatures (below 450 °C). Acidic or basic supports favor ethanol dehydration, while ethanol dehydrogenation is favored over neutral supports at low temperatures. The Rh/ZrO₂–CeO₂ catalyst exhibits the highest CO₂ selectivity up to 550 °C, which is due to the highest water gas shift (WGS) activity at low temperatures. Among the catalysts evaluated in this study, the 2wt% Rh/ZrO₂–CeO₂ catalyst exhibited the highest H₂ yield at 450 °C, which is possibly due to the high oxygen storage capacity of ZrO₂–CeO₂ resulting in efficient transfer of mobile oxygen species from the H₂O molecule to the reaction intermediate.     

Nickel Oxide Based Supported Catalysts for the In-situ Reactions of Methanation and Desulfurization in the Removal of Sour Gases from Simulated Natural Gas

Supported nickel oxide based catalysts were prepared by wetness impregnation method for the in-situ reactions of H₂S desulfurization and CO₂ methanation from ambient temperature up to 300 °C. Fe/Co/Ni (10:30:60)–Al₂O₃ and Pr/Co/Ni (5:35:60)–Al₂O₃ catalysts were revealed as the most potential catalysts, which yielded 2.9% and 6.1% of CH₄ at reaction temperature of 300 °C, respectively. From XPS, Ni₂O₃ and Fe₃O₄ were suggested as the surface active components on the Fe/Co/Ni (10:30:60)–Al₂O₃ catalyst, while Ni₂O₃ and Co₃O₄ on the Pr/Co/Ni (5:35:60)–Al₂O₃ catalyst.     

Role of Pt in the Activity and Stability of PtNi/CeO2–Al2O3 Catalysts in Ethanol Steam Reforming for H2 Production

Hydrogen production from ethanol reforming was investigated on bimetallic PtNi catalysts supported on CeO₂/Al₂O₃. Pt content was varied from 0.5 to 2.5 %. Physico-chemical characterization of the as-prepared and H₂-reduced catalysts by TPR, XRD and XPS showed that Pt phase interacted with the Ni and Ce species present at the surface of the catalysts. This interaction leads to an enhancement of the reducibility of both Ni and Ce species. Loadings of Pt higher than 1.0 wt% improved the activity and stability of the Ni/CeO₂–Al₂O₃ catalyst in ethanol steam reforming, in terms of lower formation of coke, C₂ secondary products and a constant production of CO₂ and H₂. The amount and type of carbon deposited on the catalyst was analyzed by TG–TPO while the changes in crystalline phases after reaction were studied by XRD. It was found that for Pt contents higher than 1 wt% in the catalysts, a better contact between Pt and Ce species is achieved. This Pt–Ce interaction facilitates the dispersion of small particles of Pt and thereby improves the reducibility of both Ce and Ni components at low temperatures. In this type of catalysts, the cooperative effect between Pt⁰, Ni⁰ and reduced Ce phases leads to an improvement in the stability of the catalysts: Ni provides activity in C–C bond breakage, Pt particles enhance the hydrogenation of coke precursors (C_xH_y) formed in the reaction, and Ce increases the availability of oxygen at the surface and thereby further enhances the gasification of carbon precursors.     

Nano‐engineered nickel catalysts supported on 4‐channel α‐Al2O3 hollow fibers for dry reforming of methane

A nickel (Ni) nanoparticle catalyst, supported on 4‐channel α‐Al₂O₃ hollow fibers, was synthesized by atomic layer deposition (ALD). Highly dispersed Ni nanoparticles were successfully deposited on the outside surfaces and the inside porous structures of hollow fibers. The catalyst was employed to catalyze the dry reforming of methane (DRM) reaction and showed a methane reforming rate of 2040 Lh^?1gNi^?1 at 800°C. NiAl₂O₄ spinel was formed when Ni nanoparticles were deposited on alpha‐alumina substrates by ALD, which enhanced the Ni‐support interaction. Different cycles (two, five, and ten) of Al₂O₃ ALD films were applied on the Ni/hollow fiber catalysts to further improve the interaction between the Ni nanoparticles and the hollow fiber support. Both the catalyst activity and stability were improved with the deposition of Al₂O₃ ALD films. Among the Al₂O₃ ALD coated catalysts, the catalyst with five cycles of Al₂O₃ ALD showed the best performance. © 2018 American Institute of Chemical Engineers AIChE J, 64: 2625–2631, 2018     

Effect of Catalyst Supports on Water‐Gas Shift Reaction at Ultrahigh Temperatures Using Syngas

Monometallic and bimetallic catalysts (Pt, Ni, and Pt‐Ni) with single support (Al₂O₃, TiO₂) and composite support (CeO₂/Al₂O₃, CeO₂/TiO₂) were prepared and tested for water‐gas shift reaction in a tubular quartz reactor. Syngas and steam with different steam‐to‐carbon ratios served as feedstock. The operating pressure was fixed while the reaction temperature was varied. The measured results indicated that the monometallic Ni/Al₂O₃ catalyst exhibits the lowest CO conversion and H₂ yield as compared with other catalysts. About the same CO conversion can be obtained from Pt and Pt‐Ni catalysts with single or composite support. However, higher H₂ yield can be achieved from the TiO₂‐supported catalyst compared with those supported by Al₂O₃. The experimental data also indicated that good thermal stability can be reached for the Pt‐based catalysts studied.     

Catalytic Removal of Toluene over Co3O4–CeO2 Mixed Oxide Catalysts: Comparison with Pt/Al2O3

The catalytic oxidation of toluene, chosen as VOC probe molecule, was investigated over Co₃O₄, CeO₂ and over Co₃O₄–CeO₂ mixed oxides and compared with the catalytic behavior of a conventional Pt(1 wt%)/Al₂O₃ catalyst. Complete toluene oxidation to carbon dioxide and water was achieved over all the investigated systems at temperatures below 500 °C. The most efficient catalyst, Co₃O₄(30 wt%)–CeO₂(70 wt%), showed full toluene conversion at 275 °C, comparing favorably with Pt/Al₂O₃ (100% toluene conversion at 225 °C).     

Synthesizing carbon nanotubes and carbon nanofibers over supported-nickel oxide catalysts via catalytic decomposition of methane

Supported-NiO catalysts were tested in the synthesis of carbon nanotubes and carbon nanofibers by catalytic decomposition of methane at 550 °C and 700 °C. Catalytic activity was characterized by the conversion levels of methane and the amount of carbons accumulated on the catalysts. Selectivity of carbon nanotubes and carbon nanofiber formation were determined using transmission electron microscopy (TEM). The catalytic performance of the supported-NiO catalysts and the types of filamentous carbons produced were discussed based on the X-ray diffraction (XRD) results and the TEM images of the used catalysts. The experimental results show that the catalytic performance of supported-NiO catalysts decreased in the order of NiO/SiO₂ > NiO/HZSM-5 > NiO/CeO₂ > NiO/Al₂O₃ at both reaction temperatures. The structures of the carbons formed by decomposition of methane were dependent on the types of catalyst supports used and the reaction temperatures conducted. It was found that Al₂O₃ was crucial to the dispersion of smaller NiO crystallites, which gave rise to the formation of multi-walled carbon nanotubes at the reaction temperature of 550 °C and a mixture of multi-walled carbon nanotubes and single-walled carbon nanotubes at 700 °C. Other than NiO/Al₂O₃ catalyst, all the tested supported-NiO catalysts formed carbon nanofibers at 550 °C and multi-walled carbon nanotubes at 700 °C except for NiO/HZSM-5 catalyst, which grew carbon nanofibers at both 550 °C and 700 °C.     

Sintering‐induced aromatization during n‐heptane reforming on Pt/Al2O3 catalysts

A platinum/alumina catalyst was sintered in oxygen and hydrogen atmospheres using two metal loadings of the catalyst: 0.3% Pt and 0.6% Pt. After sintering, the aromatization selectivity was investigated with the reforming of n‐heptane as the model reaction at a temperature of 500 °C and a pressure of 391.8 kPa. The primary products of n‐heptane reforming on the fresh platinum catalysts were methane and toluene, with subsequent conversion of benzene from toluene demethylation. To induce sintering, the catalysts were treated with oxygen at a flow rate of 60 mL min^?1, pressure of 195.9 kPa and temperatures between 500 and 800 °C. The 0.3% Pt/Al₂O₃ catalyst exhibited enhanced aromatization selectivity at various sintering temperatures while the 0.6% Pt/Al₂O₃ catalyst was inherently hydrogenolytic. The fact that aromatization was absent on the 0.6% Pt/Al₂O₃ catalyst was attributed to the presence of surface structures with dimensionality between two and three as opposed to essentially 2‐D structures on the 0.3% Pt/Al₂O₃ catalyst surface. On the 0.3% Pt/Al₂O₃ catalyst, the reaction product ranged from only toluene at a 500 °C sintering temperature to predominantly cracked product at a sintering temperature of 650 °C and no reaction at 800 °C. For sintering at about 650 °C, subsequent conversion of n‐heptane was complete and dropped thereafter. The turnover number was observed to change from 0.07 to 2.26 s^?1 as the dispersion changed from 0.33 to 0.09. The Koros–Nowark (K–N) test was used to check for the presence of internal diffusional incursions and Boudart's criterion was used for structural sensitivity determination. The K–N test indicated the absence of diffusional resistances while n‐heptane reforming was found to be structure sensitive on the Pt/Al₂O₃ catalyst. Copyright © 2006 Society of Chemical Industry     

Methane Conversion to Synthesis Gas by Partial Oxidation and CO2 Reforming over Supported Platinum Catalysts

Partial oxidation of methane and reforming of methane with CO₂ were carried out with Pt/Al₂O₃, PtZrO₂ and Pt/CeO₂ catalysts, in the temperature range of 350–900 °C. For partial oxidation, the catalysts showed similar stabilities, with the PtZr slightly more active. The reaction occurs in two simultaneous stages: total combustion of methane and reforming of the unconverted methane with steam and CO₂, with the O₂ conversion of 100% over the whole temperature range. For reforming with CO₂, the catalysts presented similar activities, but with distinct deactivation rates: while the PtAl deactivates very fast at 800 °C, due to deposition of inactive carbon, the PtZr and PtCe catalysts offer higher resistance to coke formation, due to the metal-support interactions and the higher mobility of oxygen in the oxide lattice.     

Zirconia: Selective oxidation catalyst for removal of tar and ammonia from biomass gasification gas

Catalysts containing zirconia and alumina were tested for their activity in the selective oxidation of tar and ammonia in biomass gasification gas. Their performance was compared with that of nickel and dolomite catalysts. Synthetic gasification gas with toluene as tar model compound was used as feed. In the presence of oxygen, zirconia and alumina-doped zirconia gave high toluene and ammonia conversions even below 600 °C. They were the most active catalysts for toluene oxidation below 700 °C and for ammonia oxidation below 650 °C. At higher temperatures than these, the impregnated ZrO₂/Al₂O₃ catalysts performed better: oxidation selectivity was improved and toluene and ammonia conversions were higher. The presence of both zirconia and alumina in the catalyst promoted toluene and ammonia conversions at low temperatures: zirconia enhanced the oxidation activity, while alumina improved the oxidation selectivity. The presence of H₂S had little effect on the activity of alumina-doped zirconia.