Role of CeO2 in Ni/CeO2–Al2O3 catalysts for carbon dioxide reforming of methane

Ni catalysts supported on γ-Al₂O₃, CeO₂ and CeO₂–Al₂O₃ systems were tested for catalytic CO₂ reforming of methane into synthesis gas. Ni/CeO₂–Al₂O₃ catalysts showed much better catalytic performance than either CeO₂- or γ-Al₂O₃-supported Ni catalysts. CeO₂ as a support for Ni catalysts produced a strong metal–support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO₂ had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/γ-Al₂O₃ catalysts for this reaction. A weight loading of 1–5 wt% CeO₂ was found to be the optimum. Ni catalysts with CeO₂ promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on CeO₂-promoted catalysts are attributed to the oxidative properties of CeO₂.     

Ni catalysts from NiAl2O4 spinel for CO2 reforming of methane

A series of mixed oxides close to NiAl₂O₄ was obtained by a sol–gel like method (propionic acid). The characterization of the different structures was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) or transmission electron microscopy (TEM). For the stoichiometric ratio of Ni to Al exactly equal to 0.5, homogeneous crystalline spinel phase was formed for a temperature of calcination equal or higher than 725 °C. A solid solution was obtained for a Ni/Al ratio lower than 0.5. The spinel structure is non-tolerant concerning a change of nickel to aluminum ratio higher than 0.5: an excess of nickel gives large particles of NiO on spinel phase. Comparative reduction and dry reforming of these oxides was made to control the formation of Ni and its sintering for applications in methane dry reforming. Preliminary reactivity results in dry reforming of methane are given.     

Structure and reactivity of plasma treated Ni/Al2O3 catalyst for CO2 reforming of methane

The glow discharge plasma treated Ni/Al₂O₃ catalyst showed an excellent anti-coke property for CO₂ reforming of methane. Characterizations using X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), temperature programmed reduction (TPR), transmission electron microscopy (TEM), and CO adsorbed infrared spectroscopy (IR) were conducted to investigate the structure and reactivity of the plasma treated Ni/Al₂O₃ catalyst for CO₂ reforming of methane. It confirms that the plasma treatment of Ni precursor at room temperature followed by calcination thermally has a significant influence on the surface characteristics of the active phase. The plasma treated catalyst contains high concentration of close packed plane with improved Ni dispersion and enhanced Ni-alumina interaction, which lead to high catalytic activity and excellent resistance to formations of filamentous carbon and encapsulating carbon.     

High combustion activity of methane induced by reforming gas over Ni/Al2O3 catalysts

During the reactions related to oxidative steam reforming and combustion of methane over -alumina-supported Ni catalysts, the temperature profiles of the catalyst bed were studied using an infrared (IR) thermograph. IR thermographical images revealed an interesting result: that the temperature at the catalyst bed inlet is much higher under CH₄/H₂O/O₂/Ar = 20/10/20/50 than under CH₄/H₂O/O₂/Ar = 10/0/20/70; the former temperature is comparable to that over noble metal catalysts such as Pt and Pd. Based on the temperature-programmed reduction and oxidation measurements over fresh and used catalysts, the metallic Ni is recognized at the catalyst bed inlet under CH₄/H₂O/O₂/Ar = 20/10/20/50, although it is mainly oxidized to NiAl₂O₄ under CH₄/H₂O/O₂/Ar = 10/0/20/70. This result indicates that the addition of reforming gas (CH₄/H₂O = 10/10) to the combustion gas (CH₄/O₂ = 10/20) can stabilize Ni species in the metallic state even under the presence of oxygen in the gas phase. This would account for its extremely high combustion activity.     

Development of ultra-stable Ni catalysts for CO2 reforming of methane

Carbon deposition behavior in CO₂ reforming of methane, methane decomposition, and CO disproportionation on nickel-magnesia solid solution was investigated by means of thermogravimetric analysis and temperature programmed reaction of deposited carbon with carbon dioxide. It was found that rapid oxidation of CH_x on Ni surface by oxygen species from CO₂ through dissociation at metal-support interface is a key step for the inhibition of carbon formation.     

ZrO2/SiO2- and La2O3/Al2O3-supported platinum catalysts for CH4/CO2 reforming

Surface-phase ZrO₂ on SiO₂ (SZrOs) and surface-phase La₂O₃ on Al₂O₃ (SLaOs) were prepared with various loadings of ZrO₂ and La₂O₃, characterized and used as supports for preparing Pt/SZrOs and Pt/SLaOs catalysts. CH₄/CO₂ reforming over the Pt/SZrOs and Pt/SLaOs catalysts was examined and compared with Pt/Al₂O₃ and Pt/SiO₂ catalysts. CO₂ or CH₄ pulse reaction/adsorption analysis was employed to elucidate the effects of these surface-phase oxides.

The zirconia can be homogeneously dispersed on SiO₂ to form a stable surface-phase oxide. The lanthana cannot be spread well on Al₂O₃, but it forms a stable amorphous oxide with Al₂O₃. The Pt/SZrOs and Pt/SLaOs catalysts showed higher steady activity than did Pt/SiO₂ and Pt/Al₂O₃ by a factor of three to four. The Pt/SZrOs and Pt/SLaOs catalysts were also much more stable than the Pt/SiO₂ and Pt/Al₂O₃ catalysts for long stream time and for reforming temperatures above 700 °C. These findings were attributed to the activation of CO₂ adsorbed on the basic sites of SZrOs and SLaOs.     

Mixtures of carbon and Ni/Al2O3 as catalysts for the microwave-assisted CO2 reforming of CH4

In this work, the microwave-assisted CO₂ reforming of CH₄ over mixtures of carbonaceous materials and an in-lab prepared Ni/Al₂O₃ was studied. Ni/Al₂O₃ is not heated by microwave radiation, and for this reason, microwave receptors, such as carbonaceous materials, must be mixed with this catalyst. In order to evaluate the role of the carbonaceous component of the blend, two different carbonaceous materials were used: an activated carbon, FY5, and a metallurgical coke, CQ. The carbonaceous component acted not only as microwave receptor but also as catalyst and, consequently, it influenced the catalytic activity of the mixture. FY5 + Ni/Al₂O₃ was found to be a better catalyst than CQ + Ni/Al₂O₃, since FY5 on its own showed a better catalytic activity than CQ. Ni/FY5, which consists of Ni impregnated directly onto the microwave receptor, was also evaluated as a catalyst. It was found that the catalytic activity of the mixture FY5 + Ni/Al₂O₃ was better than that of Ni/FY5. Finally, the influence of the heating device on the catalytic activity of FY5 + Ni/Al₂O₃ was studied. Conversions over FY5 + Ni/Al₂O₃ and microwave heating were found to be similar to conversions over Ni/Al₂O₃ and conventional heating.     

Highly active and stable Rh/MgOAl2O3 catalysts for methane steam reforming

Highly active and coke-resistant Rh catalysts were developed for methane steam reforming in microchannel chemical reactors. Rh loading was optimized on a stable MgOAl₂O₃ support to improve the volumetric productivity for methane conversion. Catalyst activities were stable over a wide range of steam/carbon ratios. In particular, experimental results demonstrated that Rh/MgOAl₂O₃ catalysts are extremely active for methane steam reforming and are resistant to coke formation at stoichiometric steam/carbon ratio of 1 for over 14 h time-on-stream with no sign of deactivation. Methane steam reforming activities on this catalyst is compared in both a microchannel reactor and a conventional micro-tubular reactor. Significant performance enhancement was observed in microchannel reactors owing to improved heat and mass transfer.     

Carbon formation and its influence on ethanol steam reforming over Ni/Al2O3 catalysts

Ethanol steam reforming was studied over Ni/Al₂O₃ catalysts. The effect of support (- and γ-Al₂O₃), metal loading and a comparison between conventional H₂ reduction with an activation method employing a CH₄/O₂ mixture was investigated. The properties of catalysts were studied by N₂ physisorption, X-ray diffraction (XRD) and temperature programmed reduction (TPR). After activity tests, the catalysts were analyzed by scanning electron microscopy (SEM) and thermogravimetric analysis (TG/DTA). Ni supported on γ-Al₂O₃ was more active for H₂ production than the catalyst supported on -Al₂O₃. Metal loading did not affect the catalytic performance. The alternative activation method with CH₄/O₂ mixture affected differently the activity and stability of the Ni/γ-Al₂O₃ and the Ni/-Al₂O₃ catalyst. This activation method increased significantly the stability of Ni/-Al₂O₃ compared to H₂ reduction. SEM and TG/DTA analysis indicate the formation of filamentous carbon during the CH₄/O₂ activation step, which is associated with the increasing catalyst activity and stability. The effect of temperature on the type of carbon formed was investigated; indicating that filamentous coke increased activity while encapsulating coke promoted deactivation. A discussion about carbon formation and the influence on the activity is presented.     

Carbon dioxide reforming of methane over Ni/Al2O3 treated with glow discharge plasma

Ni/Al₂O₃ catalyst was first treated by argon glow discharge plasma followed by calcination in air. The catalyst prepared this way exhibits an improved low-temperature activity for carbon dioxide reforming of methane, compared to the catalyst prepared without plasma treatment. The catalyst characterization using XRD, chemisorption and TEM analyses show that the plasma treatment followed by calcination thermally induces a generation of specific nickel species on the support. This kind of “plasma” metal species is highly dispersed on the support and can remain stable during reforming reactions. The average size of the “plasma” metal particles is ca. 5 nm. The plasma treatment can also enhance the anti-carbon deposition performance of the catalyst. The formation of carbon species that is responsible for catalyst deactivation can be inhibited. The catalyst stability is therefore improved.     

Ni/Al_2O_3催化剂的CO_2-TPD表征

Ni/Al_2O_3催化剂是甲烷二氧化碳重整反应制取合成气研究最多、最具应用潜力的一种催化剂。通过对催化剂进行CO_2-TPD研究,考察还原态Ni/Al_2O_3催化剂的CO_2脱附特性。结果表明,浸渍法制备的Ni/Al_2O_3催化剂CO_2脱附曲线呈现双峰,分别在(60~65)℃和(350~380)℃出现高低温两个活性位;高温CO_2吸附量为3.0 cm~3·g~(-1),低温CO_2吸附量为24.0 cm~3·g~(-1)。催化剂的CO_2吸附量与其Ni含量无关。考察选用不同载体的CO_2脱附行为,发现以Al_2O_3为载体的催化剂CO_2吸附量是MgO和SiO_2为载体催化剂的2~4倍,以TiO_2为载体的催化剂几乎不吸附CO_2。     

Characterizations and activities of the nano-sized Ni/Al2O3 and Ni/La–Al2O3 catalysts for NH3 decomposition

A series of nano-sized Ni/Al₂O₃ and Ni/La–Al₂O₃ catalysts that possess high activities for NH₃ decomposition have been successfully synthesized by a coprecipitation method. The catalytic performance was investigated under the atmospheric conditions and a significant enhancement in the activity after the introduction of La was observed. Aiming to study the influence of La promoter on the physicochemical properties, we characterized the catalysts by N₂ adsorption/desorption, XRD, H₂-TPR, chemisorption and TEM techniques. Physisorption results suggested a high specific surface area and XRD spectra showed that nickel particles are in a highly dispersed state. A combination of XRD, TEM and chemisorption showed that Ni⁰ particles with the average size lower than 5.0 nm are always obtained even though the Ni loading ranged widely from 4 to 63%. Compared with the Ni/Al₂O₃ catalysts, the Ni/La–Al₂O₃ ones with an appropriate amount of promoter enjoy a more open mesoporous structure and higher dispersion of Ni. Reduction kinetic studies of prepared catalysts were investigated by temperature-programmed reduction (TPR) method and the fact that La additive partially destroyed the metastable Ni–Al mixed oxide phase was detailed.     

Co/Al2O3 catalysts promoted with noble metals for production of hydrogen by methane steam reforming

The effect of noble metal addition on the catalytic properties of Co/Al₂O₃ was evaluated for the steam reforming of methane. Co/Al₂O₃ catalysts were prepared with addition of different noble metals (Pt, Pd, Ru and Ir 0.3 wt.%) by a wetness impregnation method and characterized by UV–vis spectroscopy, temperature programmed reduction (TPR) and temperature programmed oxidation (TPO) of the reduced catalysts. The UV–vis spectra of the samples indicate that, most likely, large amounts of the supported cobalt form Co species in which cobalt is in octahedral and tetrahedral symmetries. No peaks assigned to cobalt species from aluminate were found for the promoted and unpromoted cobalt catalysts. TPO analyses showed that the addition of the noble metals on the Co/Al₂O₃ catalyst leads to a more stable metallic state and less susceptible to the deactivation process during the reforming reaction. The Co/Al₂O₃ promoted with Pt showed higher stability and selectivity for H₂production during the methane steam reforming.     

Synthesis and properties of PdO/CeO2-Al2O3 catalysts for methane combustion

This study focuses on the loading of catalytic materials, e.g., palladium on the surface of supporting materials, with the aim to obtain catalysts with high activity for methane combustion. The catalyst PdO/CeO₂-Al₂O₃ was prepared by impregnation under ultrasonic condition. The effect of different activation methods on the activity of catalysts for methane catalytic combustion was tested. The properties of reaction and adsorption of oxygen species on catalyst surface were characterized by H₂-temperature programmed reduction (H₂-TPR), and O₂-temperature programmed desorption (O₂-TPD). Furthermore, the sulfur tolerance and sulfur poisoning mode were investigated. The results indicate that the catalyst PdO/CeO₂-Al₂O₃ activated with rapid activation shows higher activity for methane combustion and better sulfur tolerance. The result of sulfur content analysis shows that there is a large number of sulfur species on the catalyst’s surface after reactivation at high temperature. It proves that the activity of catalysts cannot be fully restored by high-temperature reactivation.     

Preparation and characterization of LaCrO3 and Cr2O3 methane combustion catalysts supported on LaAl11O18- and Al2O3-coated monoliths

A series of LaAl₁₁O₁₈- and Al₂O₃-supported LaCrO₃ and Cr₂O₃ combustion catalysts was prepared. Different active phase–support combinations were prepared and applied to cordierite monoliths. The washcoat materials were aged in flowing humid air at temperatures between 1100°C and 1400°C, after which they were characterized by BET, XRD, TPR, and EDS. The monolith catalysts were evaluated in methane combustion. The presence of an active phase retarded sintering of the Al₂O₃ support, whereas the active phase slightly decreased the thermal stability of LaAl₁₁O₁₈. X-ray measurements revealed extensive interaction between support and active phase in the washcoat materials. A substituted perovskite, LaCr_1−xAl_xO₃, is proposed to be formed in nearly all samples containing both lanthanum and chromium. The accessibility of chromium decreased rapidly after aging. The activities of the Al₂O₃-supported catalysts were higher than of those supported on LaAl₁₁O₁₈, which was related to the higher surface area of the former.     

Hydrogen production by steam reforming of LNG over Ni/Al2O3-ZrO2 catalysts: Effect of ZrO2 and preparation method of Al2O3-ZrO2

An Al₂O₃-ZrO₂ support was prepared by grafting a zirconium precursor onto the surface of commercial γ-Al₂O₃. A physical mixture of Al₂O₃-ZrO₂ was also prepared for the purpose of comparison. Ni/Al₂O₃-ZrO₂ catalysts were then prepared by an impregnation method, and were applied to the hydrogen production by steam reforming of liquefied natural gas (LNG). The effect ZrO₂ and preparation method of Al₂O₃-ZrO₂ on the performance of supported nickel catalysts in the steam reforming of LNG was investigated. The Al₂O₃-ZrO₂ prepared by a grafting method was more efficient as a support for nickel catalyst than the physical mixture of Al₂O₃-ZrO₂ in the hydrogen production by steam reforming of LNG. The well-developed tetragonal phase of ZrO₂ and the high dispersion of ZrO₂ on the surface of γ-Al₂O₃ were responsible for the enhanced catalytic performance of Ni/Al₂O₃-ZrO₂ prepared by way of a grafting method.     

CH4-CO2 reforming over Ni/Al2O3 aerogel catalysts in a fluidized bed reactor

Ni/Al₂O₃ aerogel catalysts were synthesized by a sol-gel method combined with a supercritical drying route. The catalytic performances of the catalysts in methane reforming with CO₂ were investigated in a quartz micro-reactor. The results indicated that the aerogel catalyst showed higher specific surface area and higher dispersivity of nickel species than those of impregnation catalyst. The excellent catalytic performances and stabilities were achieved over the aerogel catalysts in the fluidized bed reactor. Comprehensive characterization with TG, XRD and FESEM revealed that the aerogel catalyst in the fluidized bed had much lower carbon deposition than that in the fixed bed. The fluidization of the aerogel catalyst greatly improved the contact efficiency of gas-solid phase, which accelerated the gasification of the deposited carbon. In contrast, the deactivation of the aerogel catalyst was caused by the carbon deposition due to the catalyst without moving in the fixed bed. Moreover, decreasing activity of the impregnation catalyst in the fluidized bed resulted from the poor fluidization state of catalyst particles and low effective active sites on surface of catalyst.     

CO2 reforming of methane to syngas over highly active and stable Pt/MgO catalysts

Pt/MgO catalysts were prepared by wet impregnation. At 800 °C and atmospheric pressure, Pt/MgO catalysts exhibited a high stability at high gas hourly space velocity of 36,000 ml/g h with a CH₄/CO₂ ratio of 1.0. During 72 h time on stream, the conversion of CH₄ and CO₂ remained almost constant, at about 88% and 90%, respectively. There was no loss of Pt. After reaction, the XRD peaks of MgO became broader, indicating amorphization of MgO, which was supported by TEM results. XPS indicated that the reforming reaction had little influence on Pt. CO₂-TPSR results showed that some carbon deposition occurred under stoichiometric feed of CH₄ and CO₂, but it did not result in the deactivation of the catalyst. The deposited carbon came mainly from the decomposition of methane.     

Regeneration of S-poisoned Pd/Al2O3 catalysts for the combustion of methane

Regeneration of S-poisoned Pd/Al₂O₃ catalysts for the abatement of methane emissions from natural gas vehicles was addressed in this work.

Investigations were devoted to determine the temperature threshold allowing for catalyst reactivation under different CH₄ containing atmospheres. Under lean combustion conditions in the presence of excess O₂, partial regeneration took place only above 750 °C after decomposition of stable sulphate species adsorbed on the support. Short CH₄-reducing, O₂-free pulses led to partial catalyst reactivation already at 550 °C and to practically complete regeneration at 600 °C. Also in this case reactivation was associated with SO₂ release due to the decomposition of stable support sulphates likely promoted by CH₄ activation onto the reduced metallic Pd surface. Rich combustion pulses with CH₄/O₂ = 2 were equally effective to CH₄-reducing pulses in catalyst regeneration.

These results suggest that a regeneration strategy based on periodical natural gas pulses fed to the catalyst by a by-pass line might be efficient in limiting the effects of S-poisoning of palladium catalysts for the abatement of CH₄ emissions from natural gas engine.