Dielectric, electrical and magnetoelectric characterization of (x)Ni0.8Zn0.2Fe2O4 + (1 − x)Pb0.93La0.07(Zr0.60Ti0.40)O3 composites

The structural, electrical, dielectric, magnetic and magnetoelectric properties of (x)Ni_0.8Zn_0.2Fe₂O₄ + (1 − x)Pb_0.93La_0.07(Zr_0.60Ti_0.40)O₃ (x = 0, 0.15, 0.30, 0.45 and 1) have been studied by means of various experimental techniques. Polycrystalline samples of this series have been prepared by the double sintering ceramic method. X-ray diffraction data analysis revealed purity of the composites. Microstructural analysis using scanning electron microscopy mode depicts the presence of two phases in contact with each other. Dielectric properties were studied at and well above room temperature. Temperature dependent variation of the dielectric constant show diffused phase transition which can be well described by fitting the Lorentz-type relation, . Observation of well-saturated ferroelectric hysteresis loop and magnetic hysteresis loop for composites indicates that ferroelectric and magnetic ordering exist simultaneously at room temperature. The static value of magneto electric voltage coefficient (α_E) has been studied as a function of magnetic field at room temperature for all the composites. The maximum value of α_E is 7.53 mV/(cm Oe) for 85% PLZT-15% NZFO composites.     

Synthesis and characterization of Bi2Fe4O9 powders

Bi₂Fe₄O₉ have been successfully prepared using ethylenediaminetetraacetic (EDTA) acid as a chelating agent and ethylene glycol as an esterification agent. Heating of a mixed solution of EDTA, ethylene glycol, and nitrates of iron and bismuth at 140 °C produced a transparent polymeric resin without any precipitation, which after pyrolysis at 250 °C was converted to a powder precursor for Bi₂Fe₄O₉. The precursors were heated at 400–800 °C in air to obtain Bi₂Fe₄O₉ powder and differential scanning calorimetry (DSC), thermogravimetric (TG), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) techniques were used to characterize the precursors and the derived oxide powders. XRD analysis showed that well-crystallized and single-phase Bi₂Fe₄O₉ with orthorhombic symmetry was obtained at 700 °C for 2 h and BiFeO₃ and Fe₂O₃/FeCO₃ were intermediate phases before the formation of Bi₂Fe₄O₉. Bi₂Fe₄O₉ powders show weak ferromagnetism at room temperature.     

A new iron lead vanadate Pb2FeV3O11: Synthesis and some properties

A new iron lead vanadate, Pb₂FeV₃O₁₁, has been obtained. It melts incongruently at 650 ± 5 °C depositing two solid phases: Pb₂V₂O₇ and Fe₂O₃. Pb₂FeV₃O₁₁ crystallises in the monoclinic system. The infra-red spectrum and images of the new phase obtained by means of an electron scanning microscope are presented.     

Electrical properties of Pb0.97La0.02(Zr0.95Ti0.05)O3 antiferroelectric thin films on TiO2 buffer layer

Pb_0.97La_0.02(Zr_0.95Ti_0.05)O₃ antiferroelectric thin films with thickness of 500 nm were successfully deposited on TiO₂ buffered Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) and Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates via sol-gel process. Microstructure of Pb_0.97La_0.02(Zr_0.95Ti_0.05)O₃ thin films was studied by X-ray diffraction analyses. The antiferroelectric nature of the Pb_0.97La_0.02(Zr_0.95Ti_0.05)O₃ thin films was confirmed by the double hysteresis behaviors of polarization and double buffer fly response of dielectric constant versus applied voltage at room temperature. The capacitance-voltage behaviors of the Pb_0.97La_0.02(Zr_0.95Ti_0.05)O₃ films with and without TiO₂ buffer layer were studied, as a function of temperature. The temperature dependence of dielectric constant displayed a similar behavior and the Curie temperature (T_c) was 193 °C for films on both substrates. The current caused by the polarization and depolarization of polar in the Pb_0.97La_0.02(Zr_0.95Ti_0.05)O₃ films was detected by current density-electric field measurement.     

Fine-grained multiferroic BaTiO3/(Ni0.5Zn0.5)Fe2O4 composite ceramics synthesized by novel powder-in-sol precursor hybrid processing route

Dense, homogeneous, and fine-grained multiferroic BaTiO₃/(Ni_0.5Zn_0.5)Fe₂O₄ composite ceramics are synthesized by a novel powder-in-sol precursor hybrid processing route. This route includes the dispersion of nanosized BaTiO₃ ferroelectric powders prepared via conventional sold-state ceramic process into (Ni_0.5Zn_0.5)Fe₂O₄ ferromagnetic sol-gel precursor prepared via sol-gel wet chemistry process. Uniformly distributed slurry is obtained after ball milling and used in the fabrication of the ceramics with low sintering temperatures. The ceramics show coexistence of ferromagnetic and ferroelectric phases with obvious ferromagnetic and ferroelectric hysteresis loops at room temperature, besides exhibiting excellent magnetic and dielectric properties in a wide range of frequency. The combination of high permeability and permittivity with low losses in the ceramics enables significant miniaturization of electronic devices based on the ceramics.     

Microwave dielectric properties and microstructures of the 11Li2O-3Nb2O5-12TiO2 ceramics with B2O3 addition

The effects of B₂O₃ addition, as a sintering agent, on the sintering behavior, microstructure and microwave dielectric properties of the 11Li₂O-3Nb₂O₅-12TiO₂ (LNT) ceramics have been investigated. With the low-level doping of B₂O₃ (≤2 wt.%), the sintering temperature of the LNT ceramic could be effectively reduced to 900 °C. The B₂O₃-doped LNT ceramics are also composed of Li₂TiO₃ss and “M-phase” phases. No other phase could be observed in the 0.5-2 wt.% B₂O₃-doped ceramics sintered at 840-920 °C. The addition of B₂O₃ induced no obvious degradation in the microwave dielectric properties but increased the τ_f values. Typically, the 0.5 wt.% B₂O₃-doped ceramics sintered at 900 °C have better microwave dielectric properties of ?_r = 49.2, Q × f = 8839 GHz, τ_f = 57.6 ppm/°C, which suggest that the ceramics could be applied in multilayer microwave devices requiring low sintering temperatures.     

Hysteresis loops of polarization and magnetization in (BiNd0.05)(Fe0.97Mn0.03)O3/Pt/CoFe2O4 layered epitaxial thin film grown by pulsed laser deposition

(BiNd_0.05)(Fe_0.97Mn_0.03)O₃ (BNFM)/Pt/CoFe₂O₄ (CFO) layered thin film was fabricated on (100) SrTiO₃ substrate by pulsed laser deposition. BNFM, Pt, and CFO layers were epitaxially grown on the substrate. Almost no increase of leakage current due to the formation of heteroepitaxial structure was found, and well-saturated hysteresis loops in the polarization vs electric field and magnetization vs magnetic field curves coexist at room temperature. The remnant polarization and remnant magnetization values were 55 μC/cm², and 70-145 mA/m, respectively.     

Synthesis of (1 − x)Ca2/5Sm2/5TiO3-xLi1/2Nd1/2TiO3 ceramic powder via ethylenediaminetetraacetic acid precursor

(1 − x)Ca_2/5Sm_2/5TiO₃-xLi_1/2Nd_1/2TiO₃ (CSLNT) ceramic powder was prepared by a liquid mixing method using ethylenediaminetetraacetic acid (EDTA) as the chelating agent. TG, DTA, XRD and TEM characterized the precursors and derived oxide powders. When x = 0.3, perovskite CSLNT was synthesized at 1000 °C for 3 h in air. The CSLNT (x = 0.3) ceramics sintered at 1200 °C for 3 h show excellent microwave dielectric properties of ?_r = 99, Q_f = 6200 GHz and τ_f = 9 × 10⁻⁶ °C⁻¹.     

Structural and electrical properties of Na2Pb2Eu2W2Ti4X4O30 (X = Nb, Ta) ferroelectric ceramics

A new group of tungsten bronze family Na₂Pb₂Eu₂W₂Ti₄X₄O₃₀ (X = Nb, Ta) having all the valence elements (I-VI) were prepared by a high-temperature solid-state reaction technique. The formations of the compounds were confirmed by X-ray diffraction technique with an orthorhombic structure. Surface morphology of the compounds was studied by scanning electron microscope (SEM). Studies of dielectric properties (?_r and tan δ) of the above compounds at different frequencies in a wide temperature range (300-700 K) with an impedance analyzer exhibit a ferroelectric phase transition at 580 and 394 K for Na₂Pb₂Eu₂W₂Ti₄Nb₄O₃₀ and Na₂Pb₂Eu₂W₂Ti₄Ta₄O₃₀, respectively. Ferroelectric properties of these compounds were confirmed with polarization (hysteresis) study.     

Preparation and properties of negative thermal expansion Zr2WP2O12 ceramics

Using solid-state reaction method, Zr₂WP₂O₁₂ powder was synthesized for this study. The optimum heating condition was 1200 °C for 4 h. The obtained powder was compacted and sintered. The relative density of the Zr₂WP₂O₁₂ ceramics with no sintering additive was 60%. That of samples sintered with more than 0.5 mass% MgO was about 97%. The average grain size (D₅₀), as estimated from the polished surface of a sample sintered at 1200 °C for 4 h was about 1 μm. The obtained ceramics showed a negative thermal expansion coefficient of about −3.4 × 10⁻⁶ °C⁻¹. Young's modulus, Poisson's ratio, three-point bending strength, Vickers microhardness, and fracture toughness of the obtained ceramics were, respectively, 74 GPa, 0.25, 113 ± 13 MPa, 4.4 GPa and 2.3 MPa m^1/2.     

Effect of Pb(Fe1/2Nb1/2)O3 modification on dielectric and piezoelectric properties of Pb(Mg1/3Nb2/3)O3-PbZr0.52Ti0.48O3 ceramics

10 mol% Pb(Fe_1/2Nb_1/2)O₃ (PFN) modified Pb(Mg_1/3Nb_2/3)O₃-PbZr_0.52Ti_0.48O₃ (PMN-PZT) relaxor ferroelectric ceramics with compositions of (0.9 − x)PMN-0.1PFN-xPZT (x = 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8 and 0.9) were prepared. X-ray diffraction investigations indicated that as-prepared ceramics were of pure perovskite phase and the sample with composition of x = 0.8 was close to morphotropic phase boundary (MPB) between rhombohedral and tetragonal phase. Dielectric properties of the as-prepared ceramics were measured, and the Curie temperature (T_c) increased sharply with increasing PZT content and could be higher than 300 °C around morphotropic phase boundary (MPB) area. At 1 kHz, the sample with composition of x = 0.1 had the largest room temperature dielectric constant ?_r = 3519 and maximum dielectric constant ?_m = 20,475 at T_m, while the sample with composition of x = 0.3 possessed the maximum dielectric relaxor factor of γ = 1.94. The largest d₃₃ = 318 pC/N could be obtained from as-prepared ceramics at x = 0.9. The maximum remnant polarization (P_r = 28.3 μC/cm²) was obtained from as-prepared ceramics at x = 0.4.     

Physicochemical properties of solid-solid interactions in nanosized NiO-substituted Fe2O3/TiO2 system at 1200 °C

The solid-solid interactions between nanosized pure and NiO-substituted ferric and titanium(IV) oxides have been investigated using XRD technique and microstructure studies, also magnetic properties were studied using vibrating samples magnetometer (VSM). The amounts of substituting Ni²⁺ were x = 0, 0.2, 0.4, 0.6, 0.8 and 1 mole. A mixture equimolar proportions of finely powdered Fe₂O₃ and TiO₂ were mixed with NiO, ball milled, compressed at 250 kg/cm² and fired at 1200 °C for 4 h.The obtained results showed that with substituting Ni²⁺ concentration x = 0 only Fe₂TiO₅ phase is present (∼80 nm) which showed a very small saturation magnetic flux density (B_s), remnant magnetic flux density (B_r) and the maximum energy product (BH)_max. By the addition of x = 0.2 NiO, new phases were observed NiTiO₃ and NiFe₂O₄ of crystallite sizes 160 and 110 nm, respectively. By the increase of substituting Ni²⁺ concentration the NiTiO₃ and NiFe₂O₄ phases increased on the expense of Fe₂TiO₅ up to x = 0.4, then the increase in substituting Ni²⁺ concentration led to a decrease in Fe₂TiO₅ and NiTiO₃ while NiFe₂O₄ increases which results in a great improvement of magnetic properties.All samples exhibit a catalytic activity towards H₂O₂ decomposition and the values of rate constant increase with increasing amount of Ni²⁺ substituting. The most acidic active sites are shown by specimens substituted with x = 0 this concludes that H₂O₂ decomposition is not favored on acidic active sites.     

Low-temperature firing and microwave dielectric properties of ZnO-Nb2O5-TiO2-SnO2 ceramics with CuO-V2O5

The effects of CuO-V₂O₅ addition on the sintering temperature and microwave dielectric properties of ZnO-Nb₂O₅-TiO₂-SnO₂ were investigated. The CuO-V₂O₅ addition lowered the sintering temperature of ZnO-Nb₂O₅-TiO₂-SnO₂ ceramics effectively from 1150 to 860 °C due to the liquid-phase effect of Cu₂V₂O₇ and Cu₃(VO₄)₂, as observed by XRD. The microwave dielectric properties were found to strongly correlate with the sintering temperature and the amount of CuO-V₂O₅ addition. The maximum Qf values decreased with increasing CuO-V₂O₅ content, due to the formation of the second phase, Cu₃(VO₄)₂ and CuNbO₃. Zero τ_f value can be obtained by properly adjusting the sintering temperature. At 860 °C, ZnO-Nb₂O₅-TiO₂-SnO₂ ceramics with 1.5 wt.% CuO-V₂O₅ gave excellent microwave dielectric properties: ?_r = 42.3, Qf = 9000 GHz and τ_f = 8 ppm/°C.     

Mechanical and thermal properties of LaMgAl11O19

Lanthanum magnesium hexaaluminate (LaMgAl₁₁O₁₉) powders were synthesized successfully at 1300 °C for 4 h by solid-state reaction, and LaMgAl₁₁O₁₉ ceramic was prepared at 1700 °C for 6 h by pressureless sintering. Phase composition, microstructure, mechanical and thermophysical properties of LaMgAl₁₁O₁₉ ceramic were investigated. Results show that the flexural strength and fracture toughness of LaMgAl₁₁O₁₉ ceramic are 353.3 ± 12.5 MPa and 4.60 ± 0.46 MPa m^1/2. Young's Modulus and Poisson ratio is 295 GPa and 0.23, respectively. The linear thermal expansion coefficient of LaMgAl₁₁O₁₉ ceramic from 473 K to 1473 K is 9.17 × 10⁻⁶/K, and thermal conductivity at 1273 K is 2.55 W/m K.     

Nb NMR and Fe EPR study of local magnetic properties of magnetoelectric Pb(Fe1/2Nb1/2)O3

The ⁹³Nb NMR and Fe³⁺ EPR spectra of a magnetoelectric Pb(Fe_1/2Nb_1/2)O₃ (PFN) single crystal as well as of PFN ceramics and nanopowder have been measured. The relation between the chemical disorder and the local magnetic structure has been determined. The data show the occurrence of an antiferromagnetic (AFM) phase transition at 145 and 135 K in both single crystal and ceramic samples, respectively. The AFM phase transition is however essentially smeared out in the nanopowder. Two different Nb sites exist which have different local magnetic fields which are essentialy distributed in value. These two Nb sites correspond to different types of “chemical” order: Fe rich, Nb poor and Fe poor, Nb rich regions. The temperature dependences of the sublattice magnetizations and the values of the superhyperfine fields at the Nb ions are obtained. NMR data suggest that a spin-glass like state of PFN below T = 20 K arises from the Fe poor, Nb rich regions.     

Synthesis, low-temperature sintering and the dielectric properties of the ZnO-(1 − x)TiO2-xSnO2 (x = 0.04-0.2)

ZnO-(1 − x)TiO₂-xSnO₂ (x = 0.04-0.2) ceramics were prepared by conventional mixed-oxide method combined with a chemical processing. Fine particle powders were prepared by chemical processing to activate the formation of compound and to improve the sinterability. One wt.% of V₂O₅ and B₂O₃ with the mole ratios of 3:1 were used to lower the sintering temperature of ceramics. The effect of Sn content on phase structure and dielectric properties were investigated. The results show that the substituting Sn for Ti accelerates the hexagonal phase transition to cubic phase, and an inverse spinel structure Zn₂(Ti_1−xSn_x)O₄ solid solution forms. The best dielectric properties obtained at x = 0.12. The ZnO-0.88TiO₂-0.12SnO₂ ceramics sintered at 900 °C exhibit a good dielectric property: ?_r = 29 and tan δ = 9.86 × 10⁻⁵. Due to their good dielectric properties, low firing characteristics, ZnO-(1 − x)TiO₂-xSnO₂ (x = 0.04-0.2) can serve as the promising microwave dielectric capacitor.     

Structural characterization of 0.5PbMg1/3Nb2/3O3-0.5BaxPb(1−x)TiO3 powders

The present work reports the effects caused by barium on phase formation, morphology and sintering of lead magnesium niobate-lead titanate (PMN-50PT). Ab initio study of 0.5Pb(Mg_1/3Nb_2/3)O₃-0.5(Ba_xPb_(1−x)TiO₃) ceramic powders, with x = 0, 0.20, and 0.40 was proposed, considering that the partial substitution of lead by barium can reestablish the equilibrium of monoclinic-tetragonal phases in the system. It was verified that even for 40 mol% of barium, it was possible to obtain pyrochlore-free PMN-PT powders. The increase of the lattice parameters of PMN-PT doped-powders confirmed dopant incorporation into the perovskite phase. The presence of barium improved the reactivity of the powders, with an average particle size of 120 nm for 40 mol% of barium against 167 nm for the pure sample. Although high barium content (40 mol%) was deleterious for a dense ceramic, contents up to 20 mol% allowed 95% density when sintered at 1100 °C for 4 h.     

Synthesis and microwave dielectric properties of CaO-MgO-SiO2 submicron powders doped with Li2O-Bi2O3 by sol-gel method

Using Ca(NO₃)₂·4H₂O, Mg(NO₃)₂·6H₂O, Si(OC₂H₅)₄, LiNO₃ and Bi(NO₃)₃·5H₂O as raw materials, CaO-MgO-SiO₂ submicron powders were prepared at low temperature by sol-gel method. The crystallization temperature was decreased enormously by the introduction of Li-Bi liquid phase sintering aids into Ca-Mg-Si sol, and the powders with average particle sizes of 80-100 nm and 200-400 nm were obtained at the calcining temperature of 750 °C and 800 °C, respectively. The sintering characteristic and dielectric properties of powders calcined at 750 °C with different content of powders calcined at 800 °C were studied. When the content of powders calcined at 800 °C was 10 wt%, the dielectric ceramic sintered at 890 °C had compact structure, and possessed excellent microwave dielectric properties: ?_r = 7.16, Q × f = 25630 GHz, τ_f = −69.26 ppm/°C.     

Hygroscopicity and bulk thermal expansion in Y2W3O12

Negative thermal expansion material, Y₂W₃O₁₂ has been synthesized by the solid-state method and bulk thermal expansion of the material has been investigated from 300 to 1100 K. The material reversibly forms a trihydrate composition whose X-ray diffraction pattern can be indexed to an orthorhombic unit cell with a = 10.098(1) Å, b = 13.315(3) Å, c = 9.691(4) Å. The cell volume of the hydrated pattern is 7% smaller than the unhydrated cell volume. According to the dilatometric studies, the material shows a 3-6% increase in the linear strain at about 400 K, which can be attributed to the removal of water. Sintering the material at 1473 K leads to large grain size of >100 μm, which results in a large hysteresis in the bulk thermal expansion behavior. Hot pressing at 1273 K under a uniaxial pressure of 25 MPa results in a fine-grained (2-5 μm) ceramic. Glazing the ceramic prevents moisture pick up and a linear thermal expansion over the entire temperature range 1100-300 K and an average linear thermal expansion co-efficient of −9.65 × 10⁻⁶/K is observed. The effect of water on the thermal expansion behavior of this system is discussed.     

Structure and lithium ion conductivity of garnet-like Li5La3Sb2O12 and Li6SrLa2Sb2O12

Oxides with the nominal chemical compositions Li₅La₃Sb₂O₁₂ and Li₆SrLa₂Sb₂O₁₂ were prepared by solid-state reaction. The structures were refined by the Rietveld method using powder X-ray diffraction data. The synthesis of Li₅La₃Sb₂O₁₂ resulted in the well known garnet-related structure plus 5 wt.% of La₂LiSbO₆ in the bulk. In contrast to that, Li₆SrLa₂Sb₂O₁₂ could be synthesised in single garnet-related type phase. Lithium ion conductivities of Li₅La₃Sb₂O₁₂ and Li₆SrLa₂Sb₂O₁₂ were studied by the ac impedance method. The grain-boundary contribution to the total (bulk + grain-boundary) resistance is very small and about 5 and 3% for Li₅La₃Sb₂O₁₂ and Li₆SrLa₂Sb₂O₁₂, respectively, at 24 °C and decreases further with increase in temperature. Among the investigated compounds, Li₅La₃Sb₂O₁₂ exhibits the highest total (bulk + grain-boundary) and bulk ionic conductivity of 7.8 × 10⁻⁶ and 8.2 × 10⁻⁶ S cm⁻¹, respectively, at 24 °C. The structural data indicate that the coupled substitution Li + Sr ⇒ La leads to a closure of the bottle neck like O-O distances of the shared edges of neighbouring Li octahedra and therefore reduces the mobility of Li ions in Li₆SrLa₂Sb₂O₁₂. Scanning electron microscope (SEM) images of the Li₆SrLa₂Sb₂O₁₂ compound revealed well crystallised large homogeneous grains (∼4.8 μm) and the grains were in good contact with the neighbouring grain, which leads to a smaller grain-boundary contribution to the total resistance.