15MnVB钢160 mm xl60 mm铸坯热变形奥氏体连续冷却转变行为

采用Gleble-1500热模拟机测定了15MnVB钢在0.05～20℃/s冷速下连续冷却转变的膨胀曲线,结合光学显微镜的微观组织观察,测绘了该钢热变形奥氏体连续冷却转变过程中的动态CCT曲线;研究了其连续冷却转变产物的组织形态和硬度。实验结果表明,15MnVB钢在0.05-20℃/s冷却速率下的组织主要由铁素体+珠光体、铁素体+珠光体+贝氏体、铁素体+珠光体+贝氏体+马氏体、贝氏体+马氏体组成。     

15MnVB钢160 mm×160mm铸坯热变形奥氏体连续冷却转变行为

采用Gleble-1500热模拟机测定了15MnVB钢在0.05～20℃/s冷速下连续冷却转变的膨胀曲线,结合光学显微镜的微观组织观察,测绘了该钢热变形奥氏体连续冷却转变过程中的动态CCT曲线;研究了其连续冷却转变产物的组织形态和硬度。实验结果表明,15MnVB钢在0.05-20℃/s冷却速率下的组织主要由铁素体+珠光体、铁素体+珠光体+贝氏体、铁素体+珠光体+贝氏体+马氏体、贝氏体+马氏体组成。     

变形工艺对Q345 GJC高建钢连续冷却相变的影响

借助Gleeble-2000型热力模拟实验机,研究了Q345GJC高建钢奥氏体连续冷却过程的相变规律,结合热膨胀法和金相法,分别构建实验钢奥氏体动态和静态连续冷却相变曲线(CCT),分析了加速冷却、热变形和工艺温度对实验钢相变的影响。结果表明,与静态CCT曲线比较,实验钢的动态CCT曲线整体向左上方移动,γ/α相变开始温度随冷却速度的增大而逐渐降低;高温变形对铁素体和珠光体组织转变有利,扩大了铁素体相变区,但阻碍了贝氏体相变;奥氏体变形对贝氏体转变是双重的,高冷速变形促进贝氏体相变,低冷速变形抑制贝氏体相变。     

07MnNiMoVDR连续冷却过程相变行为研究

利用MMS-200热模拟试验机测定了07MnNiMoVDR钢的动态CCT曲线,研究了07MnNiMoVDR钢奥氏体连续冷却时的相变行为规律和显微组织。结果表明：随着冷却速度的增大,其组织由铁素体＋珠光体逐渐向贝氏体转变;随冷却速度不同,在CCT图中存在两个相变区,即低冷速的先共析铁素体＋珠光体相变区、中冷速的贝氏体相变区。     

低合金高强钢形变奥氏体相变行为及其模型

 为了研究低合金高强钢的形变奥氏体连续冷却转变行为及组织变化规律,利用Gleeble-3800热力模拟试验机对试验钢进行了多道次轧制工艺模拟试验,并根据试验所得相变温度和各冷却速度下的室温组织相对量,回归出相变模型。结果表明,试验钢在变形后的连续冷却过程中发生铁素体、珠光体、贝氏体和马氏体转变,基于对各转变的温度和组织相对量得到的相变模型分析,证实了模型的可靠性。     

12Cr2Mo1R钢相变规律研究

采用热膨胀法并结合金相组织分析及硬度变化来测定12Cr2Mo1R钢变形奥氏体的连续冷却转变温度,研究了钢的相变规律,结果表明,12Cr2Mo1R钢未变形奥氏体连续冷却转变,冷却速度<0.27 ℃/s时,组织为贝氏体+铁素体+珠光体;在0.27～8.4 ℃/s之间时,组织为贝氏体;>8.4 ℃/s时,组织为马氏体+贝氏体。变形奥氏体连续冷却转变,冷却速度<5 ℃/s时,组织为铁素体+珠光体+贝氏体;在5～20 ℃/s之间时,主要为贝氏体组织;>20 ℃/s时,得到的组织为马氏体+贝氏体。形变加速了奥氏体连续相变,使连续冷却相变温度提高。钢中Cr、Mo等合金元素,提高了过冷奥氏体的稳定性,使连续转变过程中出现了亚稳奥氏体区,提高了贝氏体的淬透性。     

35CrMo钢热变形奥氏体连续冷却转变的研究

通过在热模拟试验机上进行动态热模拟试验,测定35CrMo冷镦钢在不同冷速下连续冷却转变的膨胀曲线,再结合光学显微镜的微观组织观察,研究了过冷奥氏体连续冷却相变行为。实验结果表明:35CrMo钢在0.05-0.4℃/s冷却速度下的组织主要由铁素体+珠光体组成;当冷却速度为0.5℃/s时出现贝氏体组织,随着冷却速度的增加,贝氏体和珠光体含量逐渐增加;当冷却速度达到1.0℃/s时,组织主要为少量铁素体+珠光体+贝氏体。     

奥氏体状态对 Mn-Cr 齿轮钢连续冷却相变组织的影响

使用Cleeblel500热模拟试验机研究了成分(%)为：0.23C,0.74Mn,0.90Cr 齿轮钢奥氏体晶粒尺 寸和变形(真应变量0.4)对连续冷却相变组织的影响和连续转变冷却(CCT)曲线。实验结果表明,当齿轮钢 未变形时,获得完全多边形铁素体+珠光体混合组织的临界冷速为0.5~1℃/s,冷速较快时,中温相变产物 由贝氏体及针状铁素体组成;奥氏体变形时,多边形铁素体相变开始温度升高,获得完全多边形铁素体+珠光 体混合组织冷速增大,为1~2℃/s,中温相变产物没有出现贝氏体,只有针状铁素体。     

热轧590MPa级车轮钢的奥氏体相变行为

 利用热力模拟试验技术,研究一种Nb-V-Ti复合微合金化C-Mn钢的奥氏体连续冷却相变行为,为低成本高性能热轧590MPa级车轮钢的控制轧制和控制冷却工艺制定提供必要的理论依据。研究表明：无形变条件下,铁素体转变存在的冷却速率范围为0. 5~5℃/s,珠光体转变存在的冷却速率范围为0. 5~2℃/s;形变条件下,铁素体转变存在的冷却速率范围为0. 5~25℃/s,珠光体转变存在的冷却速率范围为0. 5~10℃/s;不论是否存在形变,贝氏体转变存在于整个冷却速率范围(0. 5~30℃/s);奥氏体区形变增加了奥氏体内部的缺陷密度,促进了非均匀形核的发生,故形变促进了铁素体转变;由于试验钢的碳的质量分数较低(＜0. 10%),形变通过促进铁素体相变而间接促进珠光体相变;当贝氏体相变前无铁素体相变时,形变对贝氏体相变有促进作用;试验钢在实际热轧试验中冷却速率宜控制在20℃/s左右,卷取温度控制在550~650℃。     

低碳微合金管线钢的连续冷却相变及组织研究

通过Gleeble 3800热模拟试验机测定了该低碳微合金管线钢的静态（无热变形）和动态连续冷却相变曲线,并通过光学显微镜和电子显微镜对连续冷却后的组织进行了详细观察和分析。发现随着冷却速度的提高,在连续冷却转变组织中依次出现多边形铁素体（PF）、珠光体（P）、针状铁素体（AF）、粒状贝氏体（GB）和下贝氏体（LB）。在未再结晶区的热变形使C曲线发生左移,扩大了试样的针状铁素体区,并使得相变后的组织得到细化。     

Nb-Ti微碳深冲双相钢的连续冷却转变规律

摘要：通过连续冷却实验研究了Nb Ti微碳深冲双相钢在不同冷却速率下的显微组织变化规律。并结合显微组织、热膨胀曲线以及实验钢的硬度值绘制出实验钢的CCT曲线。结果表明,实验钢的CCT曲线由铁素体、珠光体与贝氏体区组成,其中铁素体和贝氏体的区域较大,覆盖冷却速度范围较广。实验冷却速率下未出现马氏体组织。在05～1℃/s的慢冷速下,组织由铁素体和珠光体组成;当冷速增加至3℃/s时,贝氏体开始出现,珠光体消失。当冷速在5～10℃/s范围内时,获得铁素体+贝氏体双相组织;当冷速大于10℃/s时,铁素体相变消失,此时为纯贝氏体转变。热处理过程中若想获得一定量的马氏体组织,退火温度宜设置在820～900℃双相区较低温度范围,使合金元素充分富集于少量奥氏体中,在随后冷却过程中此奥氏体转变为马氏体组织。     

奥氏体形变对50CrV4钢相变行为的影响

利用Thermecmastor-Z型热模拟试验机,结合金相显微镜(OM)、扫描电镜(SEM)、维氏硬度计等,系统研究了奥氏体区变形对50CrV4钢连续冷却相变和等温相变规律的影响。建立了试验钢动态CCT曲线。研究结果表明,奥氏体变形能促进连续冷却转变过程中铁素体-珠光体、贝氏体转变,但亦可提高奥氏体的机械稳定性,进而抑制马氏体转变,Ms点由331.6℃(奥氏体未变形)降低至291℃(950℃下变形50%+890℃下变形50%,变形速率均为5s-1,变形后冷速为20℃/s)。当轧后冷速小于0.5℃/s时,试验钢中可获得铁素体+珠光体组织。此外,在研究不同变形量对试验钢等温相变规律影响时发现,650℃等温时,试验钢中发生铁素体-珠光体相变。随着变形量的增加(由30%增加至50%),其等温相变动力学加快(相变完成时间由197.6s减小至136.5s),铁素体体晶粒尺寸、珠光体片层间距减小,硬度增加。     

38MnSiVS非调质钢的相变模型

 对于热轧非调质钢棒材,轧后相变组织对最终产品的力学性能有着重要影响。为了准确预测38MnSiVS非调质钢棒材热轧后的组织演变和性能,利用热膨胀与定量金相方法,在Gleeble-3500热模拟机及Dil805淬火变形膨胀仪上分别测定了试验钢动态连续冷却转变(CCT)和动态等温转变(TTT)曲线。研究分析了冷却速率对试验钢相变及珠光体片层间距的影响,基于Esake and Pietrzyk和Zener and Hillert模型,分别建立了铁素体晶粒尺寸d_α、珠光体片层间距S_P关系式。结合动态等温转变曲线数据和Scheil叠加原理对铁素体体积分数进行了理论计算,为实际热轧生产中的组织性能控制提供理论依据。     

Continuous cooling transformation behavior of hot rolled TRIP 600 steel produced by CSP process

The continuous cooling transformation behavior of hot rolled TRIP 600 steel produced by CSP process was investigated by means of Thermecmastor- Z thermal simulation testing machine, Formastor- F full automatic transformation instrument, OM, SEM and microhardness tester. The dynamic and static continuous cooling transformation (CCT) curves of the experimental steel were obtained. And the effect of deformation on phase transformation behavior was discussed. The results show that the temperature of austenite to ferrite and the volume fraction of ferrite gradually decrease with the increase of cooling rate. The transformation temperature range of the pro- eutectoid ferrite is 480-716??. Meanwhile, the transformation temperature range of pearlite is 519-647??, and the volume fraction of pearlite     

变形温度对CSP热轧65Mn带钢相变行为的影响

利用ThermecMastor-Z型热模拟试验机模拟CSP工艺条件,辅以金相显微镜(OM)、扫描电镜(SEM)和维氏硬度计等,研究65Mn钢的连续冷却转变规律及变形温度对其等温相变的影响。绘制了65Mn钢的动态CCT曲线。结果表明,当轧后冷速小于2℃/s时,试验钢可获得铁素体和珠光体组织。随着冷速的增大,试验钢中将出现贝氏体和马氏体组织,硬度增大。当冷速大于40℃/s时,试验钢中的组织全为马氏体,硬度达到678.05HV。此外,在研究不同变形温度对65Mn钢等温相变的影响时发现,第2道次变形温度为920℃时,珠光体组织多呈片层状,硬度为271.86HV;随着变形温度的降低,试验钢中铁素体含量增加,珠光体球化趋势明显,粒状珠光体含量增多。当变形温度下降至860℃时,试验钢的硬度降低至252.21HV,有利于其后续深加工。     

Effect of Thermo‐Mechanical Process on Phase Transformation Behaviors of V–Ti–N Microalloyed Steel

Thermo‐mechanical simulation tests were performed on V–Ti–N microalloyed steel under three hot working conditions by using Gleeble‐3800 thermo‐mechanical simulator to study the effects of hot deformation and post‐deformation holding process on the continuous cooling transformation behaviors of overcooled austenite. The continuous cooling transformation diagrams (CCT diagrams) were determined by thermal dilation method and metallographic method. The effects of the hot deformation, post‐deformation holding, and cooling rate on the microstructure evolution were analyzed. The results show that deformation promotes ferrite and pearlite transformation. In addition, deformation leads to an increase in bainite start temperature, which becomes more markedly with the increase in cooling rate. The post‐deformation holding process is much favorable to promote carbonitride precipitation of the microalloying elements, which contributes to ferrite nucleation and smaller austenite grains. As a result, an increase in ferrite quantity and a decrease in ferrite grain size can be observed. And further more, the post‐deformation holding process reduces the effect of hot deformation on the bainite start temperature.     

Microstructure transformation behaviour of 610MPa HSLA Steel Plate for 150,000 m3 Oil Storage Tank Construction

 Static and dynamic continuous cooling transformation (CCT) on 610MPa HSLA Steel Plate for 150,000 m3 Oil Storage Tank Construction were carried out on a MMS200 thermo-mechanical simulation system. It has found that with cooling rate increases pre-eutectoid ferrite, pearlite, granular bainite and lathing bainite will appear in the transformed microstructure. In comparison with static CCT, the transforming points of acicular ferrite, granular bainite and lathing bainite in the dynamic CCT curve shift to the left proving an increased acicular ferrite and bainite transformation area.     

控轧控冷工艺对900 MPa级热轧带钢组织和性能的影响

通过动态CCT曲线测试和实验室控轧控冷试验,分析了900 MPa级热轧带钢连续冷却过程中的相变过程以及不同卷取温度下显微组织、析出相和力学性能的关系。试验结果表明:随着冷却速度提高,显微组织中多边形铁素体比例下降,贝氏体组织比例升高,冷速大于15℃/s时,显微组织全部为贝氏体;随着卷取温度升高,显微组织中针状铁素体比例下降,多边形铁素体比例升高;当卷取温度为600℃时,组织为铁素体+少量珠光体,此时析出相细小弥散,可获得抗拉强度达到1 000 MPa,延伸率17%的热轧产品。     

Effects of Chromium,Vanadium and Austenite Deformation on Transformation Behaviors of High-strength Spring Steels

The phase transformation behavior during continuous cooling of high-strength spring steels containing dif-ferent amounts of Cr was studied.Furthermore,the effects of combining Cr with V as well as austenite deformation on the transformation kinetics were investigated in the method of dilatometry and metallography hardness.The re-sults showed that,with the increase of Cr,the pearlite transformation field was enlarged,the ferrite transformation field was narrowed,and the entire phase field shifted to the right.With the addition of V,the start transformation temperature of undercooling austenite (Ar3 )was gradually increased,but the ferrite and pearlite transformation fields were not affected.Besides,the minimum critical cooling rate of martensitic transformation was also reduced.In addition,the dynamic continuous cooling transformation (CCT)curve moves to the top left compared with the static CCT curve.The transformed microstructures showed that the addition of V and the deformation not only refined the overall transformed microstructures but also reduced the lamellar spacing of pearlite.The alloying elements Cr and V promoted the Vickers hardness.However,the effect of Cr on the Vickers hardness of martensite was stronger and the influence of V on that of pearlite was stronger.Moreover,the Vickers hardness affected by the austenite deform-ation was more complex and strongly depended on the transformed microstructures.