Microscale wear of vitrified abrasive materials

The study of bonding hard materials such as aluminium oxide and cubic boron nitride (cBN) and the nature of interfacial cohesion between these materials and glass is very important from the perspective of high precision grinding. Vitrified grinding wheels are typically used to remove large volumes of metal and to produce components with very high tolerances. It is expected that the same grinding wheel be used for both rough and finish machining operations. Therefore, the grinding wheel, and in particular its bonding system, is expected to react differently to a variety of machining operations. In order to maintain the integrity of the grinding wheel, the bonding system that is used to hold abrasive grains in place will react differently to forces that are placed on individual bonding bridges. This paper examines the role of vitrification heat treatment on the development of strength between abrasive grains and bonding bridges, and the nature of fracture and wear in vitrified grinding wheels that are used for precision grinding applications.     

The quality of workpiece surface in rough machining of materials with different hardness values by using segmented grinding wheels produced in Vietnam

Segmented grinding wheels have been developed to increase the grinding ability of abrasive grains in discontinuous machining. The cutting ability of the segmented grinding wheels is evaluated. The discontinuity coefficient η of the working surface of a segmented grinding wheel is defined as a ratio of the total length of spacings between the segments to the total circumference of the wheel. Five newly developed segmented grinding wheels with η = 10.91, 16.37, 18.19, 20.01, and 21.83% and one conventional wheel (η = 0%) were used for grinding unhardened and hardened steels as well as aluminum alloy. The results have shown that a smoother workpiece surface was obtained using segmented grinding wheels with η = 18.19% in machining the unhardened steel and with η = 20.01% in machining the aluminum alloy.     

Nano finish grinding of brittle materials using electrolytic in-process dressing (ELID) technique

Recent developments in grinding have opened up new avenues for finishing of hard and brittle materials with nano-surface finish, high tolerance and accuracy. Grinding with superabrasive wheels is an excellent way to produce ultraprecision surface finish. However, superabrasive diamond grits need higher bonding strength while grinding, which metal-bonded grinding wheels can offer. Truing and dressing of the wheels are major problems and they tend to glaze because of wheel loading. When grinding with superabrasive wheels, wheel loading can be avoided by dressing periodically to obtain continuous grinding. Electrolytic inprocess dressing (ELID) is the most suitable process for dressing metal-bonded grinding wheels during the grinding process. Nano-surface finish can be achieved only when chip removal is done at the atomic level. Recent developments of ductile mode machining of hard and brittle materials show that plastically deformed chip removal minimizes the subsurface damage of the workpiece. When chip deformation takes place in the ductile regime, a defect-free nano-surface is possible and it completely eliminates the polishing process. ELID is one of the processes used for atomic level metal removal and nano-surface finish. However, no proper and detailed studies have been carried out to clarify the fundamental characteristics for making this process a robust one. Consequently, an attempt has been made in this study to understand the fundamental characteristics of ELID grinding and their influence on surface finish.     

CBN grain wear and its effects on material removal during grinding of FGH96 powder metallurgy superalloy

Grinding with cubic boron nitride (CBN) superabrasive is a widely used method of machining superalloy in aerospace industries. However, there are some issues, such as poor grinding quality and severe tool wear, in grinding of powder metallurgy superalloy FGH96. In addition, abrasive wheel wear is the significant factor that hinders the further application of CBN abrasive wheels. In this case, the experiment of grinding FGH96 with single CBN abrasive grain using different parameters was carried out. The wear characteristics of CBN abrasive grain were analyzed by experiment and simulation. The material removal behavior affected by CBN abrasive wear was also studied by discussing the pile-up ratio during grinding process. It shows that morphological characteristics of CBN abrasive grain and grinding infeed direction affect the CBN abrasive wear seriously by simulation analysis. Attrition wear, micro break, and macro fracture had an important impact on material removal characteristics. Besides, compared with the single cutting edge, higher pile-up ratio was obtained by multiple cutting edges, which reduced the removal efficiency of the material. Therefore, weakening multiple cutting edge grinding on abrasive grains in the industrial production, such as applying suitable dressing strategy, is an available method to improve the grinding quality and efficiency. The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-022-00412-2     

Simulation of cylindrical plunge grinding based on the behaviour of cutting edge wear

In cylindrical plunge grinding, a series of workpieces are ground successively without intermediate dressing of the wheel. Through the grinding, the wheel characteristic is continuously changed by the wear, fracture and new exposure of abrasive grains, having a profound effect on the grains on wheel surfaces in the cylindrical grinding process are developed to make it possible to describe the time dependent results of grinding and to establish the grinding operation standards capable of estimating grinding wheel performance and selecting grinding conditions, in which many parameters in actual grinding operations are considered. This simulation system can display its results in graphical form including the time dependent results and the effects of various parameters as well as optimization capabilities. This simulation has the same effects as many grinding experiments, and capable of selecting the optimum grinding wheels and conditions.     

An investigation on machined surface quality and tool wear during creep feed grinding of powder metallurgy nickel-based superalloy FGH96 with alumina abrasive wheels

In this study, the machined surface quality of powder metallurgy nickel-based superalloy FGH96 (similar to Rene88DT) and the grinding characteristics of brown alumina (BA) and microcrystalline alumina (MA) abrasive wheels were comparatively analyzed during creep feed grinding. The influences of the grinding parameters (abrasive wheel speed, workpiece infeed speed, and depth of cut) on the grinding force, grinding temperature, surface roughness, surface morphology, tool wear, and grinding ratio were analyzed comprehensively. The experimental results showed that there was no significant difference in terms of the machined surface quality and grinding characteristics of FGH96 during grinding with the two types of abrasive wheels. This was mainly because the grinding advantages of the MA wheel were weakened for the difficult-to-cut FGH96 material. Moreover, both the BA and MA abrasive wheels exhibited severe tool wear in the form of wheel clogging and workpiece material adhesion. Finally, an analytical model for prediction of the grinding ratio was established by combining the tool wear volume, grinding force, and grinding length. The acceptable errors between the predicted and experimental grinding ratios (ranging from 0.6 to 1.8) were 7.56% and 6.31% for the BA and MA abrasive wheels, respectively. This model can be used to evaluate quantitatively the grinding performance of an alumina abrasive wheel, and is therefore helpful for optimizing the grinding parameters in the creep feed grinding process.The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-020-00305-2     

Structural design of a carbon fiber-reinforced polymer wheel for ultra-high speed grinding

Ultra-high speed grinding (UHSG) is receiving considerable attention owing to its ability to achieve high machining accuracy and productivity. The materials and design of the grinding wheels play a significant role in this technology. Wheels with steel bodies are currently widely used, but have deficiencies such as a large mass loading imposing on the spindle, along with high power consumption, large stress and deformation, and limited practical grinding wheel speed. Wheel bodies made of carbon fiber-reinforced polymer (CFRP) show promise for use in UHSG because of the low density and high specific strength of this material. The main aim of this paper is to carry out a structural design of a CFRP grinding wheel for UHSG. Comparisons of stress and deformation, dynamic characteristics, thermal deformation, and power consumption between steel and CFRP wheel bodies reveal the superior performance characteristics of CFRP. The design of the laminate structure of the CFRP is then optimized, considering various laminate processes. The abrasive layers are designed with regard to the number and thickness of segments. Finally, a CFRP wheel for UHSG is developed based on the design proposal.     

Experimental Studies on the Grind-Hardening Effect in Cylindrical Grinding

In recent years high-strength and high-temperature alloys are used for structural and other applications. These newer high-performance materials are inherently “more difficult to machine” and also necessitate the need for higher dimensional and geometrical accuracy. Grinding is one of the most familiar and common abrasive machining processes used for the finishing operation. Compared to other machining processes such as turning, milling, etc., the specific energy developed during grinding is very high. At a critical level of specific grinding energy, the temperature rise[1]experienced by the workpiece may be such that thermal damage is induced. Heat damage induced by the grinding process is well documented and may be categorized by temper colors that are at least unsightly and probably indicative of more serious damage, including thermal cracks, tempered zone, etc.,[2]which can lead to catastrophic failure of critical machine parts that shortens the life of products subject to cyclic loading. In this work, a new heat treatment process called “grind hardening” and a mathematical model are introduced, and this work deals with how the in-process energy in grinding can be effectively utilized to improve the surface hardness and surface texture, and also to prevent damages. An experimental study has also been carried out in grinding AISI 6150 and AISI 52100 steels with an alumina wheel, and the results are discussed.     

The specific cost of grinding R6M5F3 steel with various dressing methods and electric discharge actions on Kubonit wheel working surface

A comparative study of grinding R6M5F3 steel with metal-bonded Kubonit wheels in various dressing methods and with electric discharge action on the wheel working surface is carried out based on the minimum specific cost criterion. The electric discharge dressing method has been found to provide a reduction in specific grinding cost by one order of magnitude in comparison to an abrasive method. Electric discharge actions on the wheel working surface in the course of grinding result in a higher specific machining cost; therefore, it is advisable to perform grinding with periodic in-process electric discharge dressing.     

低温冷风磨削加工参数优化试验

绿色加工是国际国内金属加工行业的趋势,采用自行设计的低温冷风装置进行绿色磨削试验研究,测试低温冷风温度(范围:- 40至- 80℃)、压力、磨削进给量、砂轮粒度等因素对试件表面加工质量的影响,发现存在磨削最佳参数组合,且低温冷风下的磨削质量可以达到传统磨削的精磨标准.     

Machining of a hybrid–metal matrix composite using an erosion–abrasion-based compound wheel in electrical discharge grinding

Machining of the composites made of matrix and reinforcement is always difficult for manufacturing industries due to their unusual properties. Among various existing traditional and non-traditional machining processes, erosion-based machining process i.e., Electrical Discharge Grinding (EDG) and the abrasion-based process i.e., Diamond Grinding (DG) have been shown their potential to machine such difficult-to-machine materials. The aims of the present study are to analyze the performances of the erosion–abrasion-based compound wheel during machining of the hybrid–metal matrix composite made of Aluminum–Silicon Carbide–Boron Carbide (Al/SiC/B₄C) by the stir casting method. The performances of the compound wheel have been tested on the EDM machine in the face grinding mode. The role of pulse current, pulse on-time, pulse off-time, wheel RPM, and abrasive grit number have been analyzed on the material removal rate (MRR) and average surface roughness (Ra). The experimental results showed that the machining with compound wheel gives higher MRR with better surface finish as compared to the uniform wheel. It has also been observed that MRR and Ra are highly affected by the pulse current, pulse on-time, and wheel RPM.     

New Vitrified Bond Diamond Grinding Wheel for Grinding the Cylinder of Polycrystalline Diamond Compacts

In this work, a kind of new vitrified bond based on Li2O-Al2O3-SiO2 glass ceramics was used to bond the diamond grains, which is made into grinding wheel and the cylindrical grinding process of polycrystalline diamond compacts （PDCs） by using the new vitrified bond diamond grinding wheel was discussed. Several factors which influence the properties of grinding wheel such as amount of vitrified bond and the kinds and amount of stuff in grinding wheel were also investigated. It was found that the new vitrified bond can firmly combine diamond grains, when there are only diamonds and vitrified bond in the structure of grinding wheel, the longevity of the grinding wheel is about 2.5-3 times as that of resin bond grinding wheel for processing PDCs. The grinding size precision of PDCs can be improved from 4-0.03 mm to 4-0.01 mm because of larger Young＇s modulus of vitrified bond than resin bond. The grinding time of a PDC product can be 1.75-2.0 min from 3.25-3.5 min, so this kind of grinding wheel can save much time for processing PDCs. Also, there is hardly noise when using this new vitrified bond diamond grinding wheel to process PDCs. The amount of vitrified bond in grinding wheel influences the longevity of grinding wheel. When the size of diamond grains is 90-107 μm, the optimal amount of vitrified bond in grinding wheel is 21% （wt pct）. When the amount of vitrified bond exceeds 21%, there are many pores in grinding block, which will decrease the longevity of grinding wheel. The existence of addition stuff such as Al2O3 or SiC can reduce the longevity of grinding wheel.     

The Process of Abrasive Machining as a Friction Interaction Between Dissimilar Materials

The portion of friction energy in the abrasive machining process has been assessed for various cutting-tool materials machined, and some methods for decreasing friction in grinding with superabrasive wheels, especially reducing friction on the bond surface of superabrasive wheels.     

Feasibility study of a flexible grinding method for precision machining of the TiAl-based alloy

This study presents detailed experimental investigations on precision machining of the TiAl-based alloy with an abrasive belt flexible grinding method. Subsequently, the feasibility of this precision machining method is evaluated with respect to the material removal rate, abrasive wear, machined surface roughness, and residual stress. The material removal rate and surface roughness were determined as experimental indicators and were measured via a three-coordinate measuring instrument and surface profiler, respectively. Micro-morphologies of the machined surface and worn abrasive belt were investigated via a scanning electron microscope. The residual stress distributions in the machined surface layer were detected by using an X-ray diffractometer. The experimental results revealed that the aforementioned evaluation indicators satisfied the desired requirements, thereby indicating that the abrasive belt flexible grinding technique was suitable for precision machining of the TiAl-based alloy. Additionally, the optimal combinations of grinding parameters were determined to obtain desirable material removal rate and machined surface roughness. The basic wear processes and characteristics of the abrasive belt were thoroughly examined. The formation of desirable residual compressive stresses in the machined surface layer was mainly attributed to low frequency and small amplitude vibration knocking at the grinding interface.     

高强度铸铁基cBN砂轮修整实验研究

消失模铸造制备的奥-贝球墨铸铁基cBN砂轮具有胎体强度高、胎体对磨粒把持力大等优点,但也存在着铸造砂轮毛坯尺寸精度不高、磨削层修整余量大、修整较为困难等不足之处.本文针对铸造铸铁基大粒度cBN砂轮毛坯,分别进行机械修整、电解修整和电解-机械-电解复合修整试验,探究不同修整方式下的最优工艺参数和修整效率,以及修整后磨粒的破碎和出刃情况.研究结果表明:采用Si C修整轮修整,当转速比为+0.3时修整效率最高,但修整效率随着时间的增加逐渐减小,修整至120 min才能够达到砂轮的目标精度;采用电解修整,砂轮在最优工艺参数下修整30 min后将产生钝化,电解修整难以继续进行;采用电解-机械-电解复合修整,不仅其修整效率比机械修整有所提高,而且砂轮表面磨粒破碎较少,磨粒出刃高度较大.     

CVD‐Diamantschleifstifte für den Werkzeug‐ und Formenbau. Abrasive Pencils for Tool and Die Making Coated by Diamond CVD

Recently developed compeDIA®‐ abrasive pencils have been produced and tested for the machining of cemented carbide molding tools. In order to produce abrasive pencils, carbide base plates have been grinded and coated with a diamond layer by a Hot‐Filament‐CVD‐process. The testing of the abrasive pencils took place with an ultra‐precision grinding machine on carbide workpieces. Surface roughness of the workpiece and its wheel life were the criteria for evaluation. For the specific adjustment of the grain size of the abrasive pencils, the adequate coating parameters were worked out, and the dependencies on basic influencing variables at coating procedures, such as nominal diameter and grinding length, were calculated. In order to be able to coat the grinded base plates with enough film adhesion, a practical pre‐treatment method was developed and tested, which removes the fringe zone, that was damaged during the grinding process. At present, the costs for the coating process are uneconomically high, though. By means of large‐scale production in connection with an automated pre‐treatment and coating it would be possible to lower the costs so far that they are on the same cost level with other coatings like TiN or TiAlN. The CVD‐Diamond abrasive pencils are very appropriate for tool and die making. It is to be expected that through further development of tools and through process optimization, the quality of the wrought workpiece can be ameliorated and surface finishes of R_a < 0,3 μm can be reached. The wheel life could be increased to appropriate values by optimization of the coating technology. The range of the machining parameters, in which the grinding process can be accomplished expediently without leading to a broken die, have been worked out. Afterwards, a die‐casting component with typically shaped elements was designed and an adequate molding tool prototype was crafted. With that, the basic conditions for tool‐ and die‐making were worked out in order to put into practice a fast and flexible machining of cemented carbide molding tools with the aid of those innovative abrasive pencils. In contrast to the traditional molding tool material made of brass, clear advantages in tool life can be made in the production of miniature serial‐parts by drawing, deep‐drawing or extrusion.     

Ductile streaks in precision grinding of hard and brittle materials

Ductile streaks produced during diamond grinding of hard and brittle materials have aided the subsequent process of polishing. Two novel techniques were used to study the formation of ductile mode streaks during diamond grinding (primary process) of germanium, silicon, and glass. In the first technique, aspheric surfaces were generated on Ge and Si at conventional speeds (5000 rpm). In the second technique, diamond grinding of plano surfaces on glass and Si surfaces using high speed (100,000 rpm) was carried out. Form accuracy, surface finish and ductile mode grinding streaks are discussed in this paper. It was found that resinoid diamond wheels gave more ductile streaks than metal-bonded wheels but better form accuracy was obtained with the latter. Ductile streaks were obtained more easily with pyrex rather than with BK 7 glass thus necessitating very little time for polishing. Ductile streaks appeared in abundance on germanium rather than silicon. Both the novel grinding techniques were used on CNC machining centres.     

高效砂轮的在线检测

硬质氮化硼磨料在很多加工场合可经济地代替常用的金刚砂，碳化硅等磨料，在加工过程中可显著提高生产率。但如何高效获得周转和平面理想的磨削结果，本文叙述的测量砂轮径跳的方法可达到其目的。     

The effect of abrading and cutting instruments on machinability of dental ceramics

The aim was to investigate the effect of machining instruments on machinability of dental ceramics. Four dental ceramics, including two zirconia ceramics were machined by three types (SiC, diamond vitrified, and diamond sintered) of wheels with a hand-piece engine and two types (diamond and carbide) of burs with a high-speed air turbine. The machining conditions used were abrading speeds of 10,000 and 15,000?r.p.m. with abrading force of 100?gf for the hand-piece engine, and a pressure of 200?kPa and a cutting force of 80?gf for the air-turbine hand-piece. The machinability efficiency was evaluated by volume losses after machining the ceramics. A high-abrading speed had high-abrading efficiency (high-volume loss) compared to low-abrading speed in all abrading instruments used. The diamond vitrified wheels demonstrated higher volume loss for two zirconia ceramics than those of SiC and diamond sintered wheels. When the high-speed air-turbine instruments were used, the diamond points showed higher volume losses compared to the carbide burs for one ceramic and two zirconia ceramics with high-mechanical properties. The results of this study indicated that the machinability of dental ceramics depends on the mechanical and physical properties of dental ceramics and machining instruments.

Open image in new window

The abrading wheels show autogenous action of abrasive grains, in which ground abrasive grains drop out from the binder during abrasion, then the binder follow to wear out, subsequently new abrasive grains come out onto the instrument surface (autogenous action) and increase the grinding amount (volume loss) of grinding materials.

     

The measurement and analysis of micro bonding force for electroplated CBN grinding wheels based on response surface methodology

The superabrasive (e.g. CBN or diamond) grain dislodgement occurrence on the wheel surface due to insufficient bonding force is the major failure phenomena in the grinding process with electroplated grinding tools. This failure leads to the abrupt increase of load on the immediate grains, accelerating more grain dislodgement on wheel surface. Ultimately, the aggregated grain dislodgement causes the workpiece profile accuracy degradation and catastrophic wheel sharpness loss. Therefore, the provision of sufficient and uniform micro bonding force all through the wheel surface is the critical task in electroplated superabrasive grinding wheel design. Considering the complexity in the micro bonding force enabling factors, e.g. the grain shape, dimensional size, spatial orientation, and bond layer thickness, it is vital to establish the quantitative and comprehensive relationship between these factors with the micro bonding force for optimal electroplated grinding wheel design. In this paper, an inclined micro-thread turning test is developed to measure the single grain micro bonding force. In addition, the finite element model of single CBN grain bonding force is established and validated to simulate the grain dislodgement. Finally, the response surface methodology (RSM) is applied to build the comprehensive correlation of the bonding force with its dimensional size, spatial orientation, and bond layer thickness. Therefore, the optimal bonding condition through regressed prediction model is identified to provide the quantitative basis for the electroplated CBN grinding wheels design, which indicates that the bonding force can be predicted for specific wheel manufacturing parameters and improved by related variable adjustment.