P-type doping of GaAs by carbon implantation

The electrical properties of C-implanted <100> GaAs have been studied following rapid thermal annealing at temperatures in the range from 750 to 950°C. This includes dopant profiling using differential Hall measurements. The maximum p-type activation efficiency was found to be a function of C-dose and annealing temperature, with the optimum annealing temperature varying from 900°C for C doses of 5 × 10¹³ cm⁻² to 800°C for doses ≥5 × 10¹⁴cm⁻². For low dose implants, the net p-type activation efficiency was as high as 75%; while for the highest dose implants, it dropped to as low as 0.5%. Moreover, for these high-dose samples, 5 × 10¹⁵ cm⁻², the activation efficiency was found to decrease with increasing annealing temperature, for temperatures above ∼800°C, and the net hole concentration fell below that of samples implanted to lower doses. This issue is discussed in terms of the amphoteric doping behavior of C in GaAs. Hole mobilities showed little dependence on annealing temperature but decreased with increasing implant dose, ranging from ∼100 cm²/V·s for low dose implants, to ∼65 cm²/V·s for high dose samples. These mobility values are the same or higher than those for Be-, Zn-, or Cd-implanted GaAs.     

Amorphization and Solid-Phase Epitaxial Growth of C-Cluster Ion-Implanted Si

Amorphization and solid-phase epitaxial growth were studied in C-cluster ion-implanted Si. C₇H₇ ions were implanted at a C-equivalent energy of 10 keV to C doses of 0.1 × 10¹⁵ cm⁻² to 8.0 × 10¹⁵ cm⁻² into (001) Si wafers. Transmission electron microscopy revealed a C amorphizing dose of ~5.0 ×  10¹⁴ cm⁻². Annealing of amorphized specimens to effect solid-phase epitaxial growth resulted in defect-free growth for C doses of 0.5 × 10¹⁵ cm⁻² to 1.0 × 10¹⁵ cm⁻². At higher doses, growth was defective and eventually polycrystalline due to induced in-plane tensile stress from substitutional C incorporation.     

The effect of dose rate and implant temperature on transient enhanced diffusion in boron implanted silicon

The effect of ion implantation dose rate and implant temperature on the transient enhanced diffusion (TED) of low energy boron implants into silicon was investigated. The implant temperature was varied between 5 and 40°C. The beam current was varied from 0.035 to 0.35 mA/cm². Three different defect regimes were investigated. The first regime was below the formation of any extended defects (5 keV B⁺ 2 × 10¹⁴/cm²) visible in the transmission electron microscope. The second regime was above the {311} formation threshold (2×10¹⁴/cm²) but below the subthreshold (type I) dislocation loop formation threshold. The final regime was above both the {311} and dislocation loop formation threshold (10 keV 5×10¹⁴/cm²). TED for these conditions is shown to be over after annealing at 750°C for 15–30 min. Secondary ion mass spectroscopy results for the three different damage regimes indicate that there is no measurable effect of dose rate or implant temperature on TED of boron implanted silicon for any of the damage regimes. It should be emphasized that the dose and energy of the boron implants is such that none of these implants approached the amorphization threshold. Above amorphization dose rate and implant temperature have dramatic effects on TED, but it appears that below the amorphization threshold there is little effect. These results suggest that for a given energy it is the ion dose not the extent of the implant damage that determines the extent of TED in boron implanted silicon.     

Rapid thermal annealing of dual Si and P implants in InP

In this study we evaluate the effects of dual implantation with different doses of Si and P on dopant activation efficiency and carrier mobility in InP:Fe. The implants were activated by a rapid thermal annealing step carried out in an optimized phosphoruscontaining ambient. For high dose implants (10¹⁴–10¹⁵ cm⁻²), which are typically employed for source/drain regions in FETs, dual implantation of equal doses of Si and P results in a higher sheet carrier concentration and lower sheet resistance. For 10¹⁴ cm⁻² Si implants at 150 keV, the optimal P co-implant dose is equal to the Si dose for most anneal temperatures. We obtain an activation efficiency of ∼70% for dual implanted samples annealed at 850° C for 10 sec. The high activation efficiencies and low sheet resistances obtained in this study emphasize the importance of stoichiometry control through the use of P co-implants and a phosphorus-containing ambient during the thermal processing of InP.     

Analysis of ion beam induced damage and amorphization of 6H-SiC by raman scattering

Raman scattering analysis of damaged SiC layers obtained by 200 keV Ge⁺ ion implantation into 6H-SiC has been performed as a function of the implanted dose (up to 10¹⁵ cm⁻²) and annealing temperature (up to 1500°C). The results obtained show the presence of three different damage levels: low damage level (doses ≤3 × 10¹² cm⁻²), medium to high damage level (doses between 10¹³ and 10¹⁴ cm^-2), and formation of a continuous amorphous layer for doses higher than the amorphization threshold of 2–3 × 10¹⁴ cm⁻². Moreover, at doses of about 10¹⁴ cm⁻² (below the amorphization threshold) amorphous domains are already observed. The Raman spectra indicate the existence of structural differences between the amorphous phase at doses below and above the threshold. After annealing, there is a residual damage which cannot be removed even at the highest annealing temperature of 1500°C. Differences in residual damage between the samples implanted at doses of 10¹⁴ and 10¹⁵ cm^-2 and annealed at the highest temperatures are observed from the peaks in the 1000–1850 cm^-1 spectral region. Finally, annealing at the highest temperature is required to observe the complete disappearance of the amorphous bands.     

Si-implantation into GaAs grown on Si

200 keV Si implantations were performed in the dose range of 5 × 10¹² − 1 × 10¹⁴ cm⁻² in GaAs grown on Si. For comparison implants were also performed in GaAs layers grown on GaAs substrates. Implanted layers were annealed by both furnace and halogen lamp rapid thermal anneals. Significantly lower donor activations were observed in GaAs layers grown on Si substrates than in the layers grown on GaAs substrates. Extremely low dopant activations were obtained for Be implants in GaAs grown on Si. Photoluminescence and photoreflectance measurements were also performed on the implanted material.     

Highly conductive buried n+ layers in lnp:fe created by MeV energy Si,S, and Si/S implantation for application to microwave devices

To obtain highly conductive buried layers in InP:Fe, MeV energy Si, S, and Si/ Simplantations are performed at 200°C. The silicon and sulfer implants gave 85 and 100 percent activation, respectively, for a fluence of 8 × 10¹⁴ cm⁻². The Si/S co-implantation also gave almost 100 percent donor activation for a fluence of 8 × 10¹⁴ cm⁻² of each species. An improved silicon donor activation is observed in the Si/S co-implanted material compared to the material implanted with silicon alone. The peak carrier concentration achieved for the Si/S co-implant is 2 × 10¹⁹ cm³. The lattice damage on the surface side of the profile is effectively removed after rapid thermal annealing. Multiple-energy silicon and sulfur implantations are performed to obtain thick and buried n⁺ layers needed for microwave devices and also hyper-abrupt profiles needed for varactor diodes.     

Halogen lamp rapid thermal annealing of Si- and Be-implanted In0.53Ga0.47As

Halogen lamp rapid thermal annealing was used to activate 100 keV Si and 50 keV Be implants in In_0.53Ga_0.47As for doses ranging between 5 × 10¹²−4 × 10¹⁴ cm⁻². Anneals were performed at different temperatures and time durations. Close to one hundred percent activation was obtained for the 4.1 × 10¹³ cm⁻² Si-implant, using an 850° C/5 s anneal. Si in-diffusion was not observed for the rapid thermal annealing temperatures and times used in this study. For the 5 × 10¹³ cm⁻² Be-implant, a maximum activation of 56% was measured. Be-implant depth profiles matched closely with gaussian profiles predicted by LSS theory for the 800° C/5 s anneals. Peak carrier concentrations of 1.7 × 10¹⁹ and 4 × 10¹⁸ cm⁻³ were achieved for the 4 × 10¹⁴ cm⁻² Si and Be implants, respectively. For comparison, furnace anneals were also performed for all doses.     

Nearly Perfect Electrical Activation Efficiencies from Silicon-Implanted Al<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Ga<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>N with High Aluminum Mole Fraction

Electrical activation studies of Al _x Ga_1−x N (x = 0.45 and 0.51) implanted with Si for n-type conductivity have been made as a function of ion dose and anneal temperature. Silicon ions were implanted at 200 keV with doses ranging from 1 × 10¹⁴ cm⁻² to 1 × 10¹⁵ cm⁻² at room temperature. The samples were subsequently annealed from 1150°C to 1350°C for 20 min in a nitrogen environment. Nearly 100% electrical activation efficiency was successfully obtained for the Si-implanted Al_0.45Ga_0.55N samples after annealing at 1350°C for doses of 1 × 10¹⁴ cm⁻² and 5 × 10¹⁴ cm⁻² and at 1200°C for a dose of 1 × 10¹⁵ cm⁻², and for the Al_0.51Ga_0.49N implanted with silicon doses of 1 × 10¹⁴ cm⁻² and 5 × 10¹⁴ cm⁻² after annealing at 1300°C. The highest room-temperature mobility obtained was 61 cm²/V s and 55 cm²/V s for the low-dose implanted Al_0.45Ga_0.55N and Al_0.51Ga_0.49N, respectively, after annealing at 1350°C for 20 min. These results show unprecedented activation efficiencies for Al _x Ga_1−x N with high Al mole fractions and provide suitable annealing conditions for Al _x Ga_1−x N-based device applications.     

Investigation of iodine as a donor in MBE grown Hg1−xCdxTe

N-type Hg_1−xCd_xTe layers with x values of 0.3 and 0.7 have been grown by molecular beam epitaxy using iodine in the form of CdI₂ as a dopant. Carrier concentrations up to 1.1 × 10¹⁸ cm⁻³ have been achieved for x = 0.7 and up to 7.6 × 10¹⁷ cm⁻³ for x=0.3. The best low temperature mobilities are 460 cm²/(Vs) and 1.2 × 10⁵ cm²/(Vs) for x=0.7 and x=0.3, respectively. Using CdI₂ as the dopant modulation doped HgTe quantum well structures have been grown. These structures display very pronounced Shubnikov-de Haas oscillations and quantum Hall plateaus. Electron densities in the 2D electron gas in the HgTe quantum well could be varied from 1.9 × 10¹¹ cm⁻² up to 1.4 × 10¹² cm⁻² by adjusting the thicknesses of the spacer and doped layer. Typical mobilities of the 2D electron gas are of the order of 5.0 × 10⁴ cm²/(Vs) with the highest value being 7.8 × 10⁴ cm²/(Vs).     

Characterization of phosphorus implantation in 4H-SiC

We report the characterization of phosphorus implantation in 4H-SiC. The implanted layers are characterized by analytical techniques (secondary ion mass spectrometry, transmission electron microscopy) as well as electrical and a sheet resistance value as low as 160 Ω/□ has been measured. We have also studied the effect of annealing time and temperature on activation of phosphorus implants. It has been shown to possible to obtain low sheet resistance (∼260 Ω/□) by annealing at a temperature as low as 1200°C. High-dose (∼ 4 × 10¹⁵ cm⁻²) implants are found to have a higher sheet resistance than that on lower dose implants which is attributed to the near-surface depletion of the dopant during high temperature anneal. Different implantation dosages were utilized for the experiments and subsequently junction rectifiers were fabricated. Forward characteristics of these diodes are observed to obey a generalized Sah-Noyce-Shockly multiple level recombination model with four shallow levels and one deep level.     

Hot-implantation of nitrogen donors into p- type α-SiC and characterization of n+-p junction

N⁺ implantation into p-type a-SiC (6H-SiC, 4H-SiC) epilayers at elevated temperatures was investigated and compared with implantation at room temperature (RT). When the implant dose exceeded 4 × 10₁₅ cm₋₂, a complete amorphous layer was formed in RT implantation and severe damage remained even after post implantation annealing at 1500°C. By employing hot implantation at 500~800°C, the formation of a complete amorphous layer was suppressed and the residual damage after annealing was significantly reduced. For implant doses higher than 10¹⁵ cm⁻², the sheet resistance of implanted layers was much reduced by hot implantation. The lowest sheet resistance of 542Ω/ was obtained by implantation at 500 ~ 800°C with a 4 × 10¹⁵ cm⁻² dose. Characterization of n⁺-p junctions fabricated by N⁺ implantation into p-type epilayers was carried out in detail. The net doping concentration in the region close to the junction showed a linearly graded profile. The forward current was clearly divided into two components of diffusion and recombination. A high breakdown voltage of 615 ∼ 810V, that is almost an ideal value, was obtained, even if the implant dose exceeded 10¹⁵ cm⁻². By employing hot implantation at 800°C, the reverse leakage current was significantly reduced.     

Tuning of electronic states in self-assembled InAs quantum dots using an ion implantation technique

We report the tunability of up to 150 meV of the ground state transition of self-assembled InAs quantum dots (QDs) using Mn ion implantation and subsequent annealing. Because of the exciton localization in the quantum dots, the photoluminescence efficiency (T=12K) of the quantum dot transition remains at 80% of its original value after implantation with a Mn dose of 1×10¹³ cm⁻²ions. Strong luminescence still remains at room temperature. At a high implantation dose (1×10¹⁵ cm⁻²) and rapid thermal annealing (700°C for 60s) about 25% of the QD luminescence intensity is recovered at T=12K.     

A technique to reduce the contact resistance to 4H-silicon carbide using germanium implantation

The effects of implanted Ge on the resistance of nickel-metal contacts to n-type and p-type 4H-SiC are reported. The Ge was implanted with an energy of 346 keV and a dose of 1.7×10¹⁶ cm⁻², and the wafer was annealed up to 1700°C for 30 min. Contact resistance measurements using the transfer length method (TLM) were performed on etched mesas of n-type and p-type 4H-SiC, with and without the Ge. For the annealed-Ni metal contacts, the Ge lowered the specific contact resistivity from 5.3×10⁻⁴ Ωcm² to 6.0×10⁻⁵ Ωcm² for n-type SiC and from 1.2×10⁻³ Ωcm² to 8.3×10⁻⁵ Ωcm² for p-type SiC. For the as-deposited (unannealed) Ni, the Ge produced ohmic contacts, whereas the contacts without Ge were rectifying. These results suggest that the addition of Ge can be an important process step to reduce the contact resistance for SiC-device applications.     

Activation of silicon ion-implanted gallium nitride by furnace annealing

Ion implantation into III–V nitride materials is animportant technology for high-power and high-temperature digital and monolithic microwave integrated circuits. We report the results of the electrical, optical, and surface morphology of Si ion-implanted GaN films using furnace annealing. We demonstrate high sheet-carrier densities for relatively low-dose (n_atoms=5×10¹⁴ cm⁻²) Si implants into AlN/GaN/sapphire heteroepitaxial films. The samples that were annealed at 1150°C in N₂ for 5 min exhibited a smooth surface morphology and a sheet electron concentration n_s ∼9.0×10¹³ cm⁻², corresponding to an estimated 19% electrical activation and a 38% Si donor activation in GaN films grown on sapphire substrates. Variable-temperature Hall-effect measurem entsindicate a Si donor ionization energy ∼15 meV.     

Optical and Magnetic Properties of ZnO:V Prepared by Ion Implantation

We report on the optical and magnetic properties of the magnetic semiconductor Zn(V)O fabricated by implantation of 195 keV ₅₁V⁺ ions into bulk ZnO:Al grown by a hydrothermal technique. Two sets of the samples, containing N _d –N _a ∼ 10¹⁵ cm⁻³ and 10¹⁸ cm⁻³, were implanted to doses of 1 × 10¹⁵ cm⁻², 3 × 10¹⁵ cm⁻², and 1 × 10¹⁶ cm⁻². The ion implantation was performed at 573 K. To remove irradiation-induced defects, the samples were annealed in air at 1073 K. Photoluminescence (PL) measurements of Zn(V)O films were carried out at temperatures from 10 K to 300 K. The effects of implantation dose and free carrier concentration on the magnetic properties of Zn(V)O were studied using a superconducting quantum interference device magnetometer. Ferromagnetism has been observed in annealed highly conductive samples implanted to 1 × 10¹⁶ cm⁻². The PL studies of ZnO bulk samples implanted with V⁺ have revealed that thermal annealing at 1073 K restores to a large extent the optical quality of the material. A new emission line centered at 3.307 eV has been found in the PL spectrum of the highly conductive samples implanted to the dose of 1 × 10¹⁶ cm⁻², which is most probably due to complexes involving V ions.     

Aluminum and boron ion implantations into 6H-SiC epilayers

Aluminum and boron ion implantations into n-type 6H-SiC epilayers have been systematically investigated. Redistribution of implanted atoms during high-temperature annealing at 1500°C is negligibly small. The critical implant dose for amorphization is estimated to be 1 × 10¹⁵ cm⁻² for Al⁺ implantation and 5 × 10¹⁵ cm^-2 for B⁺ implantation. By Al⁺ implantation followed with 1500°C-annealing, p-type layers with a sheet resistance of 22 kΩ/^— can be obtained. B⁺ implantation results in the formation of highly resistive layers, which may be attributed to the deep B acceptor level.     

Redistribution of implanted dopants in GaN

Donor (S, Se, and Te) and acceptor (Mg, Be, and C) dopants have been implanted into GaN at doses of 3–5×10¹⁴ cm⁻² and annealed at tem peratures up to 1450°C. No redistribution of any of the elements is detectable by secondary ion mass spectrometry, except for Be, which displays behavior consistent with damageassisted diffusion at 900°C. At higher temperatures, there is no further movement of the Be, for peak annealing temperature durations of 10 s. Effective diffusivities are ≤2×10⁻¹³ cm²·s⁻¹ at 1450°C for each of the dopants in GaN.     

Lateral schottky GaN rectifiers formed by Si<Superscript>+</Superscript> ion implantation

Type conversion of p-GaN by direct Si⁺ ion implantation and subsequent annealing was demonstrated by the fabrication of lateral Schottky diodes. The Si⁺ activation percentage was measured as a function of annealing time (30–300 sec) and temperature (1,000–1,200°C), reaching a maximum of ∼30% for 1,200°C, 2-min anneals. The resulting n-type carrier concentration was 1.1×10¹⁸ cm⁻³ for a moderate Si⁺ ion dose of ∼2×10¹⁴ cm⁻². The lateral Schottky diodes displayed a negative temperature coefficient of −0.15 V·K for reverse breakdown voltage.     

A silicon carbide LOCOS process using enhanced thermal oxidation by argon implantation

A process is described for creating local oxidation of silicon structure (LOCOS) structures in silicon carbide using enhanced thermal oxidation by argon implantation. Thicker oxides were created in selective regions by using multiple energy argon implants at a dose of 1 × 10¹⁵ cm⁻² prior to thermal oxidation. Atomic force microscopy was used to analyze the fabricated LOCOS structure.