A Note on Loaded Line Synthesis (Correspondence)

The purpose of this note is to present an alternate derivation of a formula for the synthesis of a loaded line. The problem is to determine the values of the normalized susceptances a and c mounted an exact quarter-wavelength apart along a uniform line. These are arranged in the order a, c, c,. . .c, a to achieve a loaded line with a given phase shift and perfect match. In order to analyze a particular line design for standing-wave ratio and phase shift over a band of frequencies on a digital computer, it is worthwhile to know the values of the susceptances to many more decimal places than one would achieve from a simple graph.     

Computer-aided design of a Si avalanche photodiode

A computer-aided design of a Si avalanche photodiode is presented. As an example, the design of the boron diffused photodiode with a desired time constant is carried out. The choice of an area of an active region is not affected by a diffusion condition but primarily by a substrate impurity concentration. For a very high speed response a moderate substrate impurity concentration must be selected. For a longer time constant than about 0.1 ns an increasing area of an active region is acceptable with a decreasing substrate impurity concentration. In a lightly doped substrate, a uniform multiplication of an active region cannot occur. Using the usual diffusion technique the acceptable highest resistivity of a substrate is about 1-2 Ω.cm. The capacitance of the guard ring occupies a considerable part in a total capacitance. Calculated results are in good agreement with experimental results.     

Simultaneous compression and amplification of ultrashort pulses atMHz repetition rates

The authors report simultaneous compression and chirped pulse amplification at megahertz repetition rates of ultrashort pulses using a cavity-dumped dye laser with a pumping argon ion laser as the amplifier. In a single stage, the pulse is compressed by a factor of 25 and the energy per pulse is simultaneously increased by a factor of 2, without reducing the repetition rate. Starting with a pulse that has a duration of 4.3 ps and a peak power of 5.8 kW, a pulse with a duration of 170 fs and a peak power of 294 kW is obtained. A second stage of pulse compression is used to obtain a broadband pulse with a duration >~50 fs and a peak power of ~100 kW at 2 MHz     

A quad-rotor system for driving and flying missions by tilting mechanism of rotors: From design to control

This article presents the hybrid design and control of a quad-rotor system called Flymobile. Flymobile is a combined system of a mobile robot and a quad-rotor system aimed to perform both flying and driving tasks. Flymobile performs flying tasks in the same way as conventional quad-rotor systems while the tilting mechanism of each rotor allows Flymobile to navigate in its terrain for a driving task. The body frame with rotors is implemented by a calibration process through a test-bed equipped with a force sensor. The triangular wheel frame is designed to mimic motions of a mobile robot with three passive wheels. Sensor data of a gyro and an accelerometer are filtered and used for controlling the attitude of the system. Focusing on a practical approach of implementing a hybrid system, a non model-based approach is applied to control Flymobile. Experimental studies are demonstrated to show the feasibility of performing both driving and flying missions.     

Equivalent transformations for the mixed lumped Brune-type sectionand uniform transmission line

As an analytical method for nonuniform transmission lines (NTLs) equivalent transformations are extended to a more general case, namely a mixed lumped Brune-type section and a uniform transmission line (unit element, UE). Circuits consisting of a cascade connection of a lumped Brune section and a UE are equivalent to one consisting of a cascade connection of a nonuniform transmission line whose characteristic impedance distribution is expressed with a trigonometric function and a lumped Brune section. This equivalent transformation method is easily applied to a circuit consisting of a lumped C section and a UE. The equivalent circuit is a circuit consisting of an NTL and a lumped C section. In this case, the characteristic impedance distribution of the NTL may be expressed in terms of a hyperbolic function. Exact network functions of the NTLs are easily obtained from the equivalent circuits without solving the telegrapher's equation. By considering the limiting case of these equivalent transformations, equivalent transformations for circuits consisting of a cascade connection of a lumped resonance circuit and a circuit and a uniform transmission line are derived     

A fast-settling CMOS op amp for SC circuits with 90-dB DC gain

A technique that combines the high-frequency behavior of a single-stage op amp with the high DC gain of a multistage design is presented. This technique is based on the concept that a very high DC gain can be achieved in combination with any unity-gain frequency achievable by a (folded-) cascode design. Bode-plot measurements for an op amp realized in a 1.6-μm process show a DC gain of 90 dB and a unity-gain frequency of 116 MHz (16-pF load). Settling measurements with a feedback factor of 1/3 show a fast single-pole settling behavior corresponding to a closed-loop bandwidth of 18 MHz (35-pF load) and a settling accuracy better than 0.03%. This technique does not cause any loss in output voltage swing. At a supply voltage of 5.0 V an output swing of about 4.2 V is achieved without loss in DC gain. The above advantages are achieved with a 30% increase in chip area and a 15% increase in power consumption     

60-GHz-band coplanar MMIC active filters

This paper presents the design and performance of 60-GHz-band coplanar monolithic microwave integrated circuit (MMIC) active filters. To compensate for the loss of the passive filter, a resonator composed of a quarter-wavelength line is terminated by a circuit with a constant negative resistance over a wide frequency band. Cross-coupling is introduced to make the attenuation poles on both sides of the passband. We develop two types of two-stage filter: one with medium bandwidth and the other with narrow bandwidth. The former shows an insertion loss of 3.0 dB with a 3-dB bandwidth of 2.6 GHz and a rejection of larger than 20 dB at a 3-GHz separation from a center frequency of 65.0 GHz. This filter also shows a noise figure of 10.5 dB. The latter filter shows an insertion loss of 2.8 dB with a 10-dB bandwidth of 2.1 GHz at a center frequency of 65.0 GHz. It also shows an output power of 5.0 dBm at a 1-dB compression point. The loss variation due to temperature variation is successfully compensated using a gate bias control circuit. The size of the MMIC filters is 2.5 mm/spl times/1.1 mm.     

Two-port active coupled microstrip antenna

A multilayer structure, based on a patch antenna coupled through a nonresonant slot to a pair of feeding microstrips is a versatile module which can be used as a radiating and resonating element in a number of different configurations. Direct connection to a low cost transistor in a feedback loop results in a very simple active antenna, as reported. Different termination conditions at the four microstrip ports give rise to a number of alternative configurations for active generation/detection and multipatch arrays.<>     

Optical pulse sequence transmission through single-mode fibers:interference signal analysis

The transmission of a pulse sequence through a single-mode fiber is considered under first- and second-order dispersion. An expression is given for the output power signal envelope in terms of the Fourier transform of a spectral function. The output envelope is composed of two terms: a linear one which is a distorted replica of the information sequence, and a nonlinear interference term. The latter is expressed in a more meaningful way and analyzed. The results allow a characterization and a classification of the interference pulses in terms of physically intuitive parameters     

Systems-in-foil – Devices,fabrication processes and reliability issues

Systems-in-foil are a new class of electronics in which a full system is integrated into a flexible end product. In this paper, we discuss current research activities and state-of-the-art in this field. Furthermore, some of the associated and expected reliability issues will be addressed on the basis of three examples. As a first example we discuss a flexible large area polymeric organic light-emitting (OLED) device. The reliability targets of these devices require protection against the detrimental influence of water. As a second example, we describe a technology for embedding thinned Si chips between polymeric foils where a careful selection of the base materials is important to account for thermal expansion differences. Finally, as a third example, a novel technology for embedding conductive circuitry in a polymeric foil is discussed in which a good matching of the elastic moduli of the polymeric foil and the embedded circuitry is crucial for the flexibility robustness.     

Fast fully 3-D image reconstruction in PET using planograms

We present a method of performing fast and accurate three-dimensional (3-D) backprojection using only Fourier transform operations for line-integral data acquired by planar detector arrays in positron emission tomography. This approach is a 3-D extension of the two-dimensional (2-D) linogram technique of Edholm. By using a special choice of parameters to index a line of response (LOR) for a pair of planar detectors, rather than the conventional parameters used to index a LOR for a circular tomograph, all the LORs passing through a point in the field of view (FOV) lie on a 2-D plane in the four-dimensional (4-D) data space. Thus, backprojection of all the LORs passing through a point in the FOV corresponds to integration of a 2-D plane through the 4-D "planogram." The key step is that the integration along a set of parallel 2-D planes through the planogram, that is, backprojection of a plane of points, can be replaced by a 2-D section through the origin of the 4-D Fourier transform of the data. Backprojection can be performed as a sequence of Fourier transform operations, for faster implementation. In addition, we derive the central-section theorem for planogram format data, and also derive a reconstruction filter for both backprojection-filtering and filtered-backprojection reconstruction algorithms. With software-based Fourier transform calculations we provide preliminary comparisons of planogram backprojection to standard 3-D backprojection and demonstrate a reduction in computation time by a factor of approximately 15.     

A 2 W CMOS Hybrid Switching Amplitude Modulator for EDGE Polar Transmitters

This paper presents a hybrid switching amplitude modulator for class-E2 EDGE polar transmitters. To achieve both high efficiency and high speed, it consists of a wideband buffered linear amplifier as a voltage source and a PWM switching amplifier with a 2 MHz switching frequency as a dependent current source. The linear amplifier with a novel class-AB topology has a high current-driving capability of approximately 300 mA with a bandwidth wider than 10 MHz. It can also operate on four quadrants with very low output impedance of about 200 at the switching frequency attenuating the output ripple voltage to less than 12 . A feedforward path, a PWM control, and a third-order ripple filter are used to reduce the current burden of the linear amplifier. The output voltage of the hybrid modulator ranges from 0.4 to 3 V for a 3.5 V supply. It can drive an RF power amplifier with an equivalent impedance of 4 up to a maximum output power of 2.25 W with a maximum efficiency of 88.3%. The chip has been fabricated in a 0.35 m CMOS process and occupies an area of 4.7 .     

Perspectives on special issues [From the Editor]

The special issues of IEEE Signal Processing Magazine (SPM) provide a forum wherein a collection of tutorials, concentrated on a specific topic, span the entire field and expose a wide-ranging segment of readers in the signal processing community to a thorough overview of the topic. The presentation of complementary tutorials, focused on a particular area in signal processing and aimed at a broad technical audience, is a unique feature of this publication. The wide exposure of selected topics to a large audience makes the special issues in SPM a top venue to educate and raise the prominence of important disciplines in signal processing.     

Ultra-Low-Power Interface Chip for Autonomous Capacitive Sensor Systems

Traditionally, most of the sensor interfaces must be tailored towards a specific application. This approach results in a high recurrent design cost and time to market. On the other hand, generic sensor interface design reduces the costs and offers a handy solution for multisensor applications. This paper presents a generic sensor interface chip (GSIC), which can read out a broad range of capacitive sensors. It contains capacitance-to-voltage converters, a switched-capacitor amplifier, an analog-to-digital converter, oscillators, clock generation circuits and a reference circuit. The system combines a very low-power design with a smart energy management, which adapts the current consumption according to the accuracy and speed requirements of the application. The GSIC is used in a pressure and an acceleration monitoring system. The pressure monitoring system achieves a current drain of 2.3 muA for a 10-Hz sample frequency and an 8-bit accuracy. In the acceleration monitoring system, we measured a current of 3.3 muA for a sample frequency of 10 Hz and an accuracy of 9 bits     

Maximum likelihood parameter estimation of textures using aWold-decomposition based model

We present a solution to the problem of modeling, parameter estimation, and synthesis of natural textures. The texture field is assumed to be a realization of a regular homogeneous random field, which can have a mixed spectral distribution. On the basis of a 2-D Wold-like decomposition, the field is represented as a sum of a purely indeterministic component, a harmonic component, and a countable number of evanescent fields. We present a maximum-likelihood solution to the joint parameter estimation problem of these components from a single observed realization of the texture field. The proposed solution is a two-stage algorithm. In the first stage, we obtain an estimate for the number of harmonic and evanescent components in the field, and a suboptimal initial estimate for the parameters of their spectral supports. In the second stage, we refine these initial estimates by iterative maximization of the likelihood function of the observed data. By introducing appropriate parameter transformations the highly nonlinear least-squares problem that results from the maximization of the likelihood function, is transformed into a separable least-squares problem. The solution for the unknown spectral supports of the harmonic and evanescent components reduces the problem of solving for the transformed parameters of the field to a linear least squares. Solution of the transformation equations then provides a complete solution of the field-model parameter estimation problem. The Wold-based model and the resulting analysis and synthesis algorithms are applicable to a wide variety of texture types found in natural images.     

The Matrix Formulation of Scattering Problems

Two regions in space are coupled through an opening in a perfectly conducting surface. By using a complete set of eigenvectors in the opening, each region can be represented by an equivalent Norton circuit involving a short-circuit current (a vector) and a generator admittance (a matrix). The particular case of a cavity at resonance is investigated. Application to a cavity terminated in a waveguide is considered, and the transformation of the equivalent circuit resulting from the shift of the terminal plane is analyzed. After solving the example of a slotted waveguide, a possible set of eigenvectors for an arbitrary opening is proposed.     

Identification of the source of an interferer by comparison with known carriers using a single satellite

We describe a method for identifying the source of a satellite interferer using a single satellite. The technique relies on the fact that the strength of a carrier signal measured at the downlink station varies with time due to a number of factors, and we use a quantum‐inspired algorithm to compute a “signature” for a signal, which captures part of the pattern of variation that is a characteristic of the uplink antenna. We define a distance measure to numerically quantify the degree of similarity between two signatures, and by computing the distances between the signature for an interfering carrier and the signatures of the known carriers being relayed by the same satellite at the same time, we can identify the antenna that the interferer originated from, if a known carrier is being relayed from it. As a proof of concept, we evaluate the performance of the technique using a simple statistical model applied to measured carrier data.     

An X‐Band Carbon‐Doped InGaP/GaAs Heterojunction Bipolar Transistor MMIC Oscillator

This paper addresses a fully‐integrated low phase noise X‐band oscillator fabricated using a carbon‐doped InGaP heterojunction bipolar transistor (HBT) GaAs process with a cutoff frequency of 53.2 GHz and maximum oscillation frequency of 70 GHz. The oscillator circuit consists of a negative resistance generating circuit with a base inductor, a resonating emitter circuit with a microstrip line, and a buffering resistive collector circuit with a tuning diode. The oscillator exhibits 4.33 dBm output power and achieves ?127.8 dBc/Hz phase noise at 100 kHz away from a 10.39 GHz oscillating frequency, which benchmarks the lowest reported phase noise achieved for a monolithic X‐band oscillator. The oscillator draws a 36 mA current from a 6.19 V supply with 47.1 MHz of frequency tuning range using a 4 V change. It occupies a 0.8 mm × 0.8 mm die area.