Fatigue resistance and damage mechanisms of 2D woven SiC/SiC composites at high temperatures

Fatigue resistance and damage mechanisms of 2D woven SiC/SiC composites at high temperatures were investigated in this research. Fatigue behavior tests were performed at 1200℃ and 1000°C at 10 Hz and stress ratio of 0.1 for maximum stresses ranging from 80 to 120 MPa, and the fatigue run-out could be defined as 10⁶ cycles. Evolution of the cumulative displacement and normalized modulus with cycles was analyzed for each fatigue condition. Fatigue run-out was achieved at 80 MPa and 1000°C. It could be found that the cycle lifetimes of the composites decreased sharply with the increasing maximum stress and temperature conditions significantly affected the fatigue performance under matrix cracking stress. The cumulative displacement showed no noticeable increase before 1000 cycles and the modulus of the failed specimens decreased before fracture. The retained properties of composites that achieved fatigue run-out, as well as the microstructures, were characterized in order to understand the fatigue behavior and failure mechanisms. The composites exhibited similar fracture morphology with matrix crack extension and glass phase oxidation formation under different conditions. In general, the high-temperature fatigue damage and failure of composites could be affected by combination of stress damage and oxidative embrittlement.     

Fatigue of three advanced SiC/SiC ceramic matrix composites at 1200°C in air and in steam

High‐temperature mechanical properties and tension‐tension fatigue behavior of three advanced SiC/SiC composites are discussed. The effects of steam on high‐temperature fatigue performance of the ceramic‐matrix composites are evaluated. The three composites consist of a SiC matrix reinforced with laminated, woven SiC (Hi‐Nicalon?) fibers. Composite 1 was processed by chemical vapor infiltration (CVI) of SiC into the Hi‐Nicalon? fiber preforms coated with boron nitride (BN) fiber coating. Composite 2 had an oxidation inhibited matrix consisting of alternating layers of silicon carbide and boron carbide and was also processed by CVI. Fiber preforms had pyrolytic carbon fiber coating with boron carbon overlay applied. Composite 3 had a melt‐infiltrated (MI) matrix consolidated by combining CVI‐SiC with SiC particulate slurry and molten silicon infiltration. Fiber preforms had a CVI BN fiber coating applied. Tensile stress‐strain behavior of the three composites was investigated and the tensile properties measured at 1200°C. Tension‐tension fatigue behavior was studied for fatigue stresses ranging from 80 to 160 MPa in air and from 60 to 140 MPa in steam. Fatigue run‐out was defined as 2 × 10⁵ cycles. Presence of steam significantly degraded the fatigue performance of the CVI SiC/SiC composite 1 and of the MI SiC/SiC composite 3, but had little influence on the fatigue performance of the SiC/SiC composite 2 with the oxidation inhibited matrix. The retained tensile properties of all specimens that achieved fatigue run‐out were characterized. Composite microstructure, as well as damage and failure mechanisms were investigated.     

Improvement of high-temperature stability of PIP SiCf/SiC material through in situ grown BNNTs

In this paper, the effect of in situ grown boron nitride nanotubes (BNNTs) and preparation temperature on mechanical behavior of PIP (Precursor Infiltration and Pyrolysis) SiC_f/SiC minicomposites under monotonic and compliance tensile is investigated. In situ BNNTs are grown on the surface of SiC fibers using ball milling–annealing process. Composite elastic modulus, tensile strength, fracture strain, tangent modulus, and loading/unloading inverse tangent modulus (ITM) are obtained and adopted to characterize the mechanical properties of the composites. Microstructures of in situ grown BNNTs and tensile fracture surfaces are observed under scanning electronic microscopic (SEM). For SiC_f/SiC minicomposites with BNNTs, the elastic modulus, tensile strength, and fracture strain are all lower than those of SiC_f/SiC minicomposites without BNNTs, mainly due to high preparation temperature and the oxidation of the PyC interphase during the annealing process. Tensile stress–strain curves of SiC_f/SiC minicomposites with and without BNNTs are predicted using the developed micromechanical constitutive model. The predicted results agreed with experimental data. This work will provide guidance for predicting the service life of SiC_f/SiC composite materials and may enable these materials to become a backbone for thermal structure systems in aerospace applications.     

Tension-tension fatigue behavior of unidirectional SiC/Si3N4 composite with strong and weak interface bonding at room temperature

In this paper, the tension-tension fatigue behavior of unidirectional SiC/Si₃N₄ ceramic-matrix composite with strong and weak interface bonding at room temperature has been investigated using a micromechanical approach. The hysteresis loops models considering different interface slip cases have been developed to establish the relationships between fatigue hysteresis loops, hysteresis dissipated energy, hysteresis modulus, and the interface shear stress. The damage evolution process under tension-tension fatigue loading has been analyzed using hysteresis loops. By comparing experimental fatigue hysteresis dissipated energy with theoretical computational values, the interface shear stresses of SiC/Si₃N₄ composite with weak and strong interface bonding were obtained for different cycle numbers. The fatigue life S‒N curves and broken fibers fraction versus cycle number curves corresponding to different fatigue peak stresses have been predicted. For SiC/Si₃N₄ with strong interface bonding, the fatigue limit stress approaches to 75% tensile strength, which is much higher than that of composite with weak interface bonding, i.e., 58% tensile strength, due to the higher interface shear stress degradation rate for weak bonding interface.     

Effects of heat treatment on the mechanical properties at elevated temperatures of plain-woven SiC/SiC composites

The effects of heat treatment on the mechanical properties of plain-woven SiC/SiC composites at 927 °C and 1200 °C in argon were evaluated through tensile tests at room temperature and at elevated temperature on the as-received and heat-treated plain-woven SiC/SiC composites, respectively. Heat treatment can improve the mechanical properties of composites at room temperature due to the release of thermal residual stress. Although heat treatment can damage the fiber, the effect of this damage on the mechanical properties of composites is generally less than the effect of thermal residual stress. Heat treatment will graphitize the pyrolytic carbon interface and reduce its shear strength. Testing temperature will affect the expansion or contraction of the components in the composites, thereby changing the stress state of the components. This study can provide guidance for the optimization of processing of ceramic matrix composites and the structural design in high-temperature environments.     

Tensile behavior of 2D-C/SiC composites at elevated temperatures: Experiment and modeling

In this paper, on-axis tensile behavior of a coated 2D-C/SiC composite at elevated temperatures was studied experimentally and theoretically. The measured data reveals that the tensile modulus and strength increase continuously with increasing temperature till 1273 K. Contrarily, the failure strains decrease sharply at high temperatures than the counterpart at room temperature, manifesting the significant influence of thermal residual stresses (TRS) on mechanical behavior of C/SiC composites. Simulation of stress-strain response is based on a two-scale analytical model, in which the plain-weave element is idealized as a cross-ply laminate and its macroscopic mechanical parameters are evaluated by shear-lag approach. The primary calculation was concentrated on TRS of the composite. And, a new crack evolution model was introduced to describe the stochastic cracking process. The total strain response including residual strain and elastic strain from the loading-unloading-reloading conception was finally formulated through micromechanical analysis involving the influence of TRS on matrix cracking and interface debonding. Additionally, a strength model was developed for plain-weave structures by using shear-lag theory, statistical theory and rule of mixture. Both of the proposed constitutive and strength models can give accurate predictions for 2D-C/SiC composites at elevated temperatures.     

Tensile creep behavior of three-dimensional four-step braided SiC/SiC composite at elevated temperature

This article presents experimental results for tensile creep deformation and rupture behavior of three-dimensional four-step braided SiC/SiC composites at 1100 °C and 1300 °C in air. The creep behavior at 1300 °C exhibited a long transient creep regime and the creep rate decreased continuously with time. The creep behavior at 1100 °C exhibited an apparent steady-rate regime and the creep deformation was smaller than that at 1300 °C. However, the creep rupture time at both temperatures showed little difference. The mechanisms controlling creep deformation and rupture behavior were analyzed.     

Mechanical hysteresis and damage evolution in C/SiC composites under fatigue loading at room and elevated temperatures

In this paper, the mechanical hysteresis and damage evolution in C/SiC ceramic matrix composites (CMCs) under cyclic tension-tension fatigue loading at room and elevated temperatures in air and in inert atmosphere and different loading frequencies are investigated. The fatigue hysteresis loops models considering multiple matrix cracking modes are developed to establish the relationships between fatigue hysteresis loops, fatigue hysteresis dissipated energy, and fiber/matrix interface shear stress. The evolution of fatigue hysteresis dissipated energy and interface shear stress vs applied cycles is analyzed. It was found that the interface shear stress degradation rate increases with fatigue peak stress, and loading frequency from 40 to 375 Hz.     

Creep behavior identification of an environmental barrier coating using full-field measurements

For the use of thermal and environmental barrier coating (T/EBC) with ceramic matrix composites, it is crucial to master the behavior under (extreme) environments representative of the hot section of engine turbines. An experimental setup to simulate such thermal loading has been developed with various diagnostics enabling for kinematic and thermal field measurements, which are used to drive a finite element model and estimate thermomechanical properties such as creep parameters of the coating.     

In-situ tensile damage and fracture behavior of PIP SiC/SiC minicomposites at room temperature

In-situ tensile damage and fracture behavior of original SiC fiber bundles, processed and uncoated SiC fiber bundles, SiC fiber bundle with PyC interphase, SiC/SiC minicomposites without/with PyC interphase are analyzed. Relationships between load-displacement curves, stress-strain curves, and micro damage mechanisms are established. A micromechanical approach is developed to predict the stress-strain curves of SiC/SiC minicomposites for different damage stages. Experimental tensile stress-strain curves of two different SiC fiber reinforced SiC matrix without/with interphase are predicted. Evolution of composite’s tangent modulus, interface debonding fraction, and broken fiber fraction with increasing applied stress is analyzed. For the BX™ and Cansas-3303™ SiC/SiC minicomposite with interphase, the composite’s tangent modulus decreased with applied stress especially approaching tensile fracture; the interface debonding fraction increased with applied stress, and the composite’s tensile fracture occurred with partial interface debonding; and the broken fiber fraction increased with applied stress, and most of fiber’s failure occurred approaching final tensile fracture.     

Theoretical prediction on structure evolution and optimal properties of silicon modified hexagonal boron nitride as interphase in SiCf/SiC composite

To predict the effects of Si doping on hexagonal boron nitride (h-BN) and to achieve a balance between mechanical and oxidation properties for the interphase modification in SiC_f/SiC composites, we herein calculate and analyze the crystal structures and mechanical properties of (BN)₆₄Si_x (x = 4, 8, 16, 32) models by means of density functional theory (DFT) calculations and ab initio molecular dynamics (aiMD) simulations. The possible trends of crack deflection and self-healing ability are discussed. The modeling shows an obvious transition of (BN)₆₄Si_x from the layered crystal structure and anisotropic mechanical property to amorphous structure and isotropic mechanical property as the Si doping content up to 36.1 wt%. Regarding to the application of interphase in SiC_f/SiC composites, (BN)₆₄Si₁₆ model structure possess the highest debonding potential according to Cook and Gordon’s criteria and illustrates the higher self-healing capacity at elevated temperature.     

Fabrication and characterization of carbon fiber reinforced SiC ceramic matrix composites based on 3D printing technology

A novel method has been developed to fabricate carbon fiber reinforced SiC (C_f/SiC) composites by combining 3D printing and liquid silicon infiltration process. Green parts are firstly fabricated through 3D printing from a starting phenolic resin coated carbon fiber composite powder; then the green parts are subjected to vacuum resin infiltration and pyrolysis successively to generate carbon fiber/carbon (C_f/C) preforms; finally, the C_f/C preforms are infiltrated with liquid silicon to obtain C_f/SiC composites. The 3D printing processing parameters show significant effects on the physical properties of the green parts and also the resultant C_f/C preforms, consequently greatly affecting the microstructures and mechanical performances of the final C_f/SiC composites. The overall linear shrinkage of the C_f/SiC composites is less than 3%, and the maximum density, flexural strength and fracture toughness are 2.83?±?0.03?g/cm³, 249?±?17.0?MPa and 3.48?±?0.24?MPa m^1/2, respectively. It demonstrates the capability of making near net-shape C_f/SiC composite parts with complex structures.     

Evaluation of mechanical properties of a dense SiC/SiCN composite produced via PIP process

The material behavior of Polymer Infiltration and Pyrolysis based SiC/SiCN composites is studied and the characteristic thermal and mechanical properties in on- (0/90 °) and off-axis (±45 °) direction are summarized. The tensile properties are determined at room temperature and 1300 °C. Based on the ratio of Young’s modulus and strength between on- and off-axis loading, a new approach for the classification of Weak Matrix Composites (WMC) and Weak Interface Composites (WIC) is proposed, which seems to be reasonable for various CMCs. Even without fibre coating mechanical behavior of SiC/SiCN is similar to that of WIC. In order to explain this, a microstructure model is developed and confirmed by analysis of fracture surface. The effect of temperature on the tensile properties is investigated through analysis of residual thermal stresses. Even though at 1300 °C the strength is slightly lower, the fracture strain increased significantly from RT to 1300 °C.     

Oxidation and thermal shock resistant properties of Al-modified environmental barrier coating on SiCf/SiC composites

SiC_f/SiC ceramic matrix composites (CMCs) are being widely used in the hot-sections of gas-turbines, especially for aerospace applications. These CMCs are subjected to surface recession if exposed to heat-corrosion. In this research, an alternative environmental barrier coating (EBC) is introduced to protect the SiC_f/SiC CMC from high temperature degradation that is, Al film was deposited on the surface of SiC_f/SiC CMC followed by heat-treatment in a vacuum. After that, a dense Al₂O₃ overlay was in-situ synthesized on the surface of CMC, and in this process the microstructure evolution of SiC_f/SiC CMC was analyzed. The oxidation and thermal shock resistance were characterized, showing that the Al-modified SiC_f/SiC CMC has a better oxidation resistance, because the dense Al₂O₃ overlay can hinder oxygen diffusion from environment. What is more, the water-quenching testes show that the Al-modified SiC_f/SiC CMC has a good spallation resistance.     

A time-dependent vibration damping model of fiber-reinforced ceramic-matrix composites at elevated temperature

In this paper, a time-dependent vibration damping model of fiber-reinforced ceramic-matrix composites (CMCs) is developed. Considering time and temperature dependent interface damages of oxidation, debonding, and slip, the relationships between composite vibration damping, material properties, internal damages, oxidation duration and temperature are established. The effects of material properties, vibration stress, damage state, and oxidation temperature on time-dependent composite vibration damping and interface damages of C/SiC composite are discussed. The time-dependent composite vibration damping decreases with fiber volume, matrix crack spacing and interface shear stress, and increases with vibration stress. The experimental composite vibration damping and internal damages of 2D C/SiC composite for different oxidation duration t = 2, 5 and 10 h at elevated temperatures T = 700, 1000 and 1300 °C are predicted. When the oxidation duration was short (i.e., t = 2 h), the composite vibration damping decreased with temperature; however, when the oxidation duration was long (i.e., t = 5 and 10 h), the composite vibration damping decreased with temperature below 1000 °C, and increased with temperature to 1300 °C.     

A chemo-mechanical coupled constitutive model applied to the oxidation simulation of SiC/SiC composite

Herein, a chemo-mechanical coupled constitutive and failure model is proposed to predict the tensile behavior of SiC/SiC composites under oxidizing environments. The diffusion of O₂ through the oxide scale and the oxidation reaction of SiC/O₂ are modeled and implemented in finite element software, through a user-defined element. Numerical validation studies and tests are conducted on a domestic SiC fiber. An orthotropic constitutive model for reinforcements, which considers modulus reduction due to oxidation damage, and a continuum damage model associated with O₂ diffusion along the micro-cracks in the SiC matrix are subsequently presented. The developed framework is used to simulate the mechanical behavior and oxidation process of a single fiber SiC/SiC composite.     

Sn-containing Si3N4-based composites for adaptive excellent friction and wear in a wide temperature range

Ceramic design based on reducing friction and wear-related failures in moving mechanical systems has gained tremendous attention due to increased demands for durability, reliability and energy conservation. However, only few materials can meet these requirements at high temperatures. Here, we designed and prepared a Sn-containing Si₃N₄-based composite, which displayed excellent tribological properties at high temperatures. The results showed that the friction coefficient and wear rate of the composites were reduced to 0.27 and 4.88 × 10^?6 mm³ N^?1 m^?1 in air at 800 °C. The wear mechanism of the sliding pairs at different temperatures was revealed via detailed analyses of the worn surfaces. In addition, the tribo-driven graphitization was detected on the wear surfaces and in the wear debris, and the carbon phase was identified by SEM, TEM, and Raman spectrum.     

High-temperature mechanical properties and oxidation resistance of SiCf/SiC ceramic matrix composites with multi-layer environmental barrier coatings for turbine applications

Continuous silicon carbide fiber reinforced silicon carbide (SiC_f/SiC) ceramic matrix composites are considered promising materials as high-temperature components of advanced aero-engines. However, due to their susceptibility to oxidation and corrosion at high temperature, environmental barrier coatings (EBCs) must be applied on the surface of SiC_f/SiC. In this study, Si/Y₂SiO₅/LaMgAl₁₁O₁₉ (LMA) multi-layer EBCs were fabricated to protect SiC_f/SiC by using atmospheric plasma spraying (APS). The high-temperature tensile fatigue performance of SiC_f/SiC with and without EBCs was evaluated. The results indicated that EBCs significantly improved the tensile fatigue properties of SiC_f/SiC at high temperature in air atmosphere. Meanwhile the bending strength of specimens after isothermal aging or not was also tested. The multi-layer EBCs in this study may be a promising EBCs system for SiC_f/SiC after some improvements.     

Wear behavior of SiC nanowire-reinforced SiC coating for C/C composites at elevated temperatures

To improve the wear resistance of SiC coating on carbon/carbon (C/C) composites, SiC nanowires (SiCNWs) were introduced into the SiC wear resistant coating. The dense SiC nanowire-reinforced SiC coating (SiCNW-SiC coating) was prepared on C/C composites using a two-step method consisting of chemical vapor deposition and pack cementation. The incorporation of SiCNWs improved the fracture toughness of SiC coating, which is an advantage in wear resistance. Wear behavior of the as-prepared coatings was investigated at elevated temperatures. The results show that the wear resistance of SiCNW-SiC coating was improved significantly by introducing SiC nanowires. It is worth noting that the wear rate of SiCNW-SiC coating was an order of magnitude lower than that of the SiC coating without SiCNWs at 800 °C. The wear mechanisms of SiCNW-SiC coating at 800 °C were abrasive wear and delamination. Pullout and breakage of SiC grains resulted in failure of SiC coating without SiCNWs at 800 °C.