Effect of holmium on the magnetic and electrical properties of barium based W-type hexagonal ferrites

A series of BaHo_xFe_16−xO₂₇ (x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0) W-type hexagonal ferrites were prepared by co-precipitation technique at high annealing temperature of 1320 °C. XRD reveals single W-type hexagonal phase in these ferrites. The grain size is measured by SEM analysis using line intercept method. Saturation magnetization, retentivity and coercivity were measured from MH-loops taken on VSM. It was observed that magnetization increases with the increase of Ho content due to difference in ionic radii of Ho³⁺ (0.901 Å) and Fe³⁺ (0.67 Å) ions. Room temperature dc resistivity increases as a function of Ho³⁺ that may be due to separation between grains. The dc electrical resistivity decreases as a function of temperature which indicates the semi-conducting behavior of the samples.     

Optimization of structural,electrical, and magnetic properties of ytterbium substituted W-type hexaferrite for multi-layer chip inductors

The rare earth (Yb³⁺) substituted W-type hexagonal ferrites with composition CaPb_2-xYb_xFe₁₆O₂₇ (x = 0.0, 0.5, 1.0, 1.5, 2.0) were synthesized by a facile and cost-effective sol-gel auto combustion method with post heat treatment. The synthesized hexagonal ferrites were characterized by a variety of analytical techniques, and an impedance analyzer was used to investigate the effects of Ytterbium on structural, magnetic, spectral and dielectric properties. The relationship between their impedance, structure and dielectric properties was investigated. The X-ray diffraction patterns verify the presence of single-phase W-type hexagonal ferrites. Physical properties such as D_bulk (bulk density), D_xrd (X-ray density), and P (porosity) of the CaPb_2-xYb_xFe₁₆O₂₇ W-type hexagonal ferrites were calculated. The bulk density of all the samples was decreased, and X-ray intensity was increased with the Ytterbium replacement in the W-type hexaferrite. By adding Yb³⁺ ions, the lattice parameters, cell volume and X-ray density were reduced due to the substitution of ytterbium with smaller ionic radii compared to the lead ion with large ionic radii. The AC-conductivity was increased from (1.523 × 10^?5 to 6.699 × 10^?5) Ωcm^?1. The dielectric constant and tangent loss was found to decrease substantially. The magnetic properties were found to enhance by the substitution of Yb³⁺. The low coercivity value of Yb³⁺ substituted W-type hexagonal ferrites are suitable for magnetic recording media operated at a high-frequency regime. The enhancement of electrical, dielectric and magnetic characteristics suggests these materials as promising for multi-layer chip inductors (MLCIs) circuit applications.     

Monodisperse hexagonal SrFe12O19 nanoflake with enchanced magnetic properties

Monodisperse SrFe₁₂O₁₉ (SrM) nanoflakes were successfully fabricated via a modified hydrothermal method. The effects of Fe³⁺/Sr²⁺ (R_F/S) and OH⁻/NO₃⁻ (R_O/N) molar ratio on phase, structure and morphology of the products were investigated by XRD, FT-IR, FESEM, and TEM. Meanwhile, the magnetic properties of the product were investigated via vibrating sample magnetisem (VSM). Results demonstrated that when the R_F/S=5 and R_O/N=2, the single phase SrFe₁₂O₁₉ particles were obtained. The as-obtained SrFe₁₂O₁₉ particles had monodisperse nanoflake structure and nano-micro scale in vertical and horizontal direction of SrM ferrite particle. The magnetic property results showed that such structure SrM ferrite particle had prospective saturation magnetization and coercivity, the largest values of Ms and Hc were 62.96 emu/g and 94.83 kA/m, respectively, which make it have a potential application as magnetic recording media and magneto-optical devices material.     

Sol gel derived MnTi doped Co2 W-type hexagonal ferrites: Structural,physical, spectral and magnetic evaluations

W-type BaSr Co₂ hexaferrites doped with Mn and Ti of the following composition Ba_0.5Sr_0.5Co₂Mn_xTi_xFe_16-2xO₂₇ (x = 0.00, 0.50, 1.00, 1.50, 2.00, 2.50) were synthesized by sol-gel auto ignition method. The structure, phase, spectral bands, microstructure, and magnetic behaviors of the MnTi doped BaSr Co₂ W-type ferrites were determined using XRD, FTIR, FESEM, and VSM respectively. Structural and physical parameters such as lattice parameters ‘a’ and ‘c’, crystallite size, cell volume, micro strain, porosity, bulk and X-ray density of the MnTi doped BaSr Co₂ W-type hexaferrites were evaluated. The detailed and refined structural properties were determined using the Rietveld refinement of the MnTi doped BaSr Co₂ W-type hexagonal ferrites. MAUD software was used for the refinement of the MnTi doped BaSr Co₂ W-type hexagonal ferrites patterns. Rb, Rwp and Rexp values were found in the range of 10–19 for MnTi doped BaSr Co₂ W-type hexagonal ferrites. The force constants at respective sites were also investigated through FTIR studies. FESEM images showed the hexagonal shape of the MnTi doped hexaferrites. Magnetic properties were estimated from the hysteresis loops recorded by VSM. The magnetic properties were decreased with the MnTi doping. However, anisotropic field was also found to be decreased with MnTi doping. This might be due to the ionic radii and nonmagnetic substitution of Ti in BaSr Co₂ W-type hexagonal ferrites. The low coercivity values of these ferrites suggest the use of MnTi doped BaSr Co₂ W-type ferrites for microwave absorption, memory devices and magnetic radar absorbing materials (MRAMs) in high frequency regime.     

Structural, physical, magnetic and electrical properties of La-substituted W-type hexagonal ferrites

Lanthanum doped W-type hexaferrites BaZn₂La_xFe_16−xO₂₇ (x = 0, 0.2, 0.4, 0.6, 0.8, 1.0) were synthesized by co-precipitation and sintered at 1320 °C. The X-ray diffraction reveals W-type hexagonal structure with few traces of secondary phase. The decrease in grain size as a function of La-concentration is attributed to the fact that La acts as a grain inhibitor. The saturation magnetization and remanance decrease due to spin canting on B-sites. The increase in coercivity follows 1/r behavior where r is the radius of grain. The DC resistivity was observed to increase from 0.59 × 10⁷ to 8.42 × 10⁷ Ω cm with increasing La-contents due to the unavailability of Fe³⁺ ions. This enhancement in resistivity makes these materials promising candidates for use at high frequencies in order to reduce eddy current losses.     

The effect of reaction temperature on the structural and magnetic properties of nano CoFe2O4

Nano cobalt ferrites (CoFe₂O₄) were co-precipitated at various reaction temperatures (60, 70 and 80 °C) for 1 h. The reaction temperature greatly influenced the crystallite size and the magnetic behaviours of the nano CoFe₂O₄. The mean crystallite size ranged from 9 to 15 nm with the increase in the reaction temperature and the intensity of metal oxide vibrations at 568–550 cm⁻¹ were also inclined. The synthesized samples were in the stoichiometric ratio of 1:2 (Co:Fe) with roughly spherical morphology. The synthesized cobalt nanoferrites exhibited ferromagnetism at room temperature and 5 K, and the saturation magnetization increased from 6.4 to 20 emu/g with the crystallite size.     

Electrical and magnetic properties of ZrO2-doped lithium-titanium-zinc ferrite ceramics

This report documents the effect of 0–3 wt% ZrO₂ additive on the electrical and magnetic properties of LiTiZn ferrite. Ferrite powder of Li_0.65Fe_1.6Ti_0.5Zn_0.2Mn_0.05O₄ composition was synthesised at 900 °C for 4 h in air. Ferrite ceramics doped with ZrO₂ were sintered at 1010 °C for 2 h in air. A spreading resistance analysis showed that LiTiZn ferrites exhibited nonuniform distribution of depth DC resistivity, which varied in the range of (0.25–2.3) × 10⁹ Ω⋅cm depending on the amount of additive. Zirconia also affected the magnetic properties of ferrite so that the magnetisation increased and the initial permeability decreased as the ZrO₂ content increased. In addition, the Curie temperature varied. The permeability spectra measured in the frequency range from 10 MHz to 18 GHz changed depending on the zirconia content.     

Microstructure and enhanced magnetic properties of low-temperature sintered LiZnTiMn ferrite ceramics with Bi2O3-Al2O3 additive

Bi₂O₃ and Al₂O₃ were proven to separately have an impact on grain growth of LiZn ferrite ceramics. In this study, we synthesized LiZnTiMn ferrite ceramics under low temperature (<920 °C) using rationally designed formula of Bi₂O₃-Al₂O₃ as sintering agents. Microstructures, densities, and ferromagnetic performances were systematically investigated. Results show that appropriate amount of Bi₂O₃-Al₂O₃ leads to successful sintering of LiZnTiMn ferrites even below 900 °C. X-Ray diffraction (XRD) and scanning electron microscopy (SEM) results show that spinel structure ferrite ceramics were obtained and that the addition of Bi₂O₃-Al₂O₃ accelerated solid-state reaction. Corresponding ferromagnetic properties, including saturation induction (B_s), remanence square ratio, coercivity (H_c), ferromagnetic resonance linewidth (ΔH), and M_s, were also investigated. At 920 °C, with addition amount of x=1 wt%, we obtain excellent performance: B_s=306 mT, B_r/B_s=0.849, H_c=2.34Oe, and ΔH=275 Oe. Results indicate that Bi₂O₃-Al₂O₃ is promising sintering agent for low-temperature sintering of LiZnTiMn ferrite ceramics.     

Superior thermal stability of polymer capped Fe3O4 magnetic nanoclusters

In general, the technologically important ferrites nanoparticles, magnetite and maghemite, are converted from cubic to the more stable rhombohedral structure above 500°C‐700°C under air/vacuum/inert atmosphere. Here, we report, the superior thermal stability of polymer capped Fe₃O₄ (PCIO) nanocluster (synthesized using microwave‐assisted polyol approach) up to 1000°C under vacuum and inert atmosphere. Raman spectra of post annealed PCIO nanoclusters show the Fe₃O₄ phase with carbon signature due to the decomposition of polymer matrix. The carbon layer seems to act as a thermal shield and increases the activation energy thereby preventing the intrusion of heat, oxygen, volatiles mass into the magnetic core. The presence of carbon layer was further confirmed from the high‐resolution transmission electron microscopic image. After thermal annealing at 1000°C, PCIO nanoclusters showed superparamagnetic behavior with a saturation magnetization of 89 emu/g, close to the bulk saturation magnetization of Fe₃O₄ phase. In contrast, the uncoated Fe₃O₄ (UCIO) nanoclusters decompose at 700°C into α‐Fe₂O₃ and FeO phases under similar annealing conditions. Our findings open up new possibilities of stabilizing nanomaterials for high‐temperature applications.     

Nb2O5-doped NiZnCo ferrite ceramics with ultra-high magnetic quality factor and low coercivity for high-frequency electronic devices

This work investigates the influence of niobium pentoxide (Nb₂O₅) as dopant, on the structural, magnetic, and dielectric properties of NiZnCo ferrites. The results showed that Nb₂O₅ was an effective dopant, and the Nb⁵⁺ ions entered the B site to replace Fe³⁺ ions, which altered the electromagnetic properties of the NiZnCo ferrite. In particular, the coercivity (H_c) was 20～24 Oe, and the magnetic quality factor (Q), was more than 200 at x = 0 and x = 0.1 wt%, which is 4～5 times higher than that of NiZn and NiCuZn ferrites. Excellent electromagnetic properties were obtained for 0.1 wt% Nb₂O₅-doped NiZnCo ferrite, i.e., M_s = 88.3 emu/g, H_c =20.4 Oe, ρ = 2.4 × 10⁵ Ω m and Q = 202 @20 MHz. These excellent electromagnetic properties of Nb₂O₅-doped NiZnCo ferrites could be potentially applied to resonators and capacitors at high frequency.     

Effects of Re addition on phase stability and mechanical properties of hexagonal OsB2

ReB₂‐type hexagonal Osmium diboride (OsB₂) has been predicted to exhibit higher hardness than its orthorhombic phase, but hexagonal‐orthorhombic phase transformation occurs at temperature higher than 600°C, resulting in the decrease in its hardness. Therefore, ReB₂‐type hexagonal OsB₂ samples with Re addition were produced by a combination of mechanochemical method and pressureless sintering technique, and the effects of Rhenium (Re) addition on phase composition, thermal stability and mechanical properties of OsB₂ were investigated in this study. X‐ray diffraction (XRD) analysis of the as‐synthesized powders by high‐energy ball milling indicates the formation of hexagonal Os_1‐xRe_xB₂ solid solution with Re concentration of 5 and 10 at.% without forming a second phase. After being sintered at 1700°C, part of the hexagonal phase in OsB₂ transformed to orthorhombic structure, while Os_0.95Re_0.05B₂ and Os_0.9Re_0.1B₂ maintained their hexagonal structure. This suggests that the thermal stability of the hexagonal OsB₂ was significantly improved with the addition of Re. Scanning electron microscopy (SEM) photographs show that all of the as‐sintered samples exhibit a homogeneous microstructure with some pores and cracks formed throughout the samples with the relative density >90%. The measurements of micro‐hardness, nano‐hardness, and Young's modulus of the OsB₂ increased with Re addition, and these properties of the sample with 5 at.% addition of Re is higher than that with 10 at.% Re.     

纳米结构铁氧体磁性材料的制备和应用

铁氧体纳米磁性材料是一类非常重要的无机功能材料,其应用涉及到电子、信息、航天航空、生物医学等领域。综述了纳米结构铁氧体磁性材料化学制备方法的研究进展,分析了相关纳米结构铁氧体磁性材料的制备工艺对磁性能的影响,以及它们的应用,展望了研究和开发纳米结构铁氧体磁性材料的新性能和新技术的应用前景。     

Structural and magnetic properties of strontium substituted NiZn ferrite nanopowders

Sr-substituted NiZn ferrite nanopowders, Ni_0.5-xZn_0.5Sr_xFe_2.0O₄ (0≤x≤0.20), were synthesized by the sol-gel auto-combustion method. The effects of Sr substitution on the structural and magnetic properties have been investigated. Differential thermal analysis-thermogravimetry (DTA-TG), X-ray diffraction (XRD) and vibrating sample magnetometer (VSM) measurements were used to characterize chemical, structural and magnetic properties. The DTA-TG results indicate that there are three steps of combustion process. XRD results indicate that the lattice parameter increases, and the average crystallite size decreases with increasing Sr substitution. The Sr₂FeO₄ and SrFe₁₂O₁₉ impurity phases formed with excess Sr substitution. The saturation magnetization monotonically decreases with the increase of Sr substitution. Meanwhile, the coercivity initially decreases with the increase of Sr substitution when x≤0.15, and increases when x>0.15.     

Enhanced magnetic and dielectric properties of Y doped bismuth ferrite nanofiber

Yttrium doped Bismuth ferrite (BFO) nanofiber was fabricated via a sol-gel-based electrospinning process with the fiber diameter in the range of 60–220 nm. The crystal structure, magnetic and dielectric properties were investigated at room temperature. The Rietveld refinement results indicate the phase transition from space group R3c to Pbnm by the Y doping. Dramatic increase of magnetization has been achieved in Y doped BFO nanofiber. Compared with BFO nanoparticle, the Bi_0.95Y_0.05FeO₃ nanofiber exhibits nearly eighteen-fold improved magnetization, which is the strongest in the reported Y doped BFO at the same doping level. The largely improved magnetization mainly originates from the serious suppression of spiral spin structure by the small crystal size of nanofiber structure. Moreover, the Bi_0.95Y_0.05FeO₃ nanofiber holds the lower dielectric loss and obvious dependence of the capacitance on bias voltage, indicating the improved ferroelectricity due to the decreased leakage current. The simultaneous enhancement of ferroelectricity and magnetization in Y doped BFO nanofiber suggests that nanofiber structure plays an important role in improving multiferroic performance.     

BaFe9(Ti0.5Mn0.5)3O19铁氧体粉末的合成及磁性能研究

采用溶胶-凝胶自蔓延法合成了BaFe9(Ti0.5Mn0.5)3O19铁氧体粉末,利用XRD、TEM和VSM对样品进行表征及磁性能研究。结果表明,合成样品为均匀单一的纳米级铁氧体粉末,平均粒径80nm,焙烧温度对磁能影响显著,焙烧温度过高不利于提高样品磁性能。     

The role of Pb and annealing temperature on the structural,magnetic, optical and dielectric properties of W-type hexaferrite nanostructures

In this paper, W-type Sr_1-xPb_xCo₂Fe₁₆O₂₇ nanostructures were synthesized by auto-combustion sol-gel method. Then, the effects of annealing temperature and Pb contents on the structural, magnetic, optical, and dielectric properties of Sr_1-xPb_xCo₂Fe₁₆O₂₇ nanostructure were investigated. First, a gel of metal nitrates with a specific molar ratio with x different was prepared and then the gel was annealed at different temperatures for 4?h. To determine the annealing temperature of the samples, the prepared gel was examined by thermogravimetric analysis and differential thermal analysis. The morphology and crystal structure of the prepared samples were characterized by field emission scanning electron microscopy (FESEM) and X-ray diffraction pattern (XRD). The results of XRD patterns indicated that the annealing temperature of synthesized Sr_1-xPb_xCo₂Fe₁₆O₂₇ was reduced by increasing Pb contents. In addition, FESEM images showed that the microstructure of the samples was homogeneous and uniform, but since the samples have a magnetic property, the particles were aggregated. Fourier transform infrared analysis (FT-IR) was used to confirm the phase formation. The FT-IR results of the samples indicated that the tetrahedral and octahedral sites, which are the important attributes of hexaferrites, were formed. The magnetic properties of the samples were measured by vibrating sample magnetometer (VSM). The VSM results of the samples showed that because of increasing Pb content, the amount of saturation magnetization and that of magnetic coercivity decreased from 81.29 to 10.23?emu/g and 2285–477?Oe, respectively. The optical properties of the samples were investigated by ultraviolet–visible spectroscopy, which revealed that the energy gap decreases and the absorption peaks move towards longer wavelengths by increasing Pb content. The dielectric properties of the samples were investigated by the LCR meter. It was found that by increasing frequency, the dielectric constant (ε^′) and the dielectric loss (?) of the samples were decreased.     

尖晶石型铁氧体Cu_xZn_(1-x)Fe_2O_4(x=0~0.5)的制备及光催化性能的研究

采用溶胶-凝胶法制备了尖晶石型铁氧体Cu x Zn1-x Fe2O4。利用XRD,SEM对纳米颗粒的结构、形貌进行了表征。结果表明,所合成的样品为尖晶石型铁氧体,形貌呈规则颗粒,随着Cu掺杂量的增加可使样品粒径减小。通过对甲基橙的降解情况对其光催化活性进行了研究。结果表明,经过Cu2+掺杂可加快甲基橙降解速率,少量掺杂的Cu x Zn1-x Fe2O4样品,光催化活性可以提高。     

Formation of brownmillerite type calcium ferrite (Ca2Fe2O5) and catalytic properties in propylene combustion

Several types of calcium ferrite base catalysts (Ca/Fe = 0.33–3) for propylene (C₃H₆) combustion were prepared. Calcium ferrite catalyst with brownmillerite crystal structure provided catalytic activity for C₃H₆ combustion in the temperature range of 250–450 °C. The brownmillerite phase (Ca₂Fe₂O₅) was responsible for the formation of oxygen adspecies (O ₂ ⁻ ) in the surface layer below 450 °C.     

Microwave-assisted solution synthesis,microwave sintering and magnetic properties of cobalt ferrite

A simple, soft, and fast microwave-assisted hydrothermal method was used for the preparation of nanocrystalline cobalt ferrite powders from commercially-available Fe(NO₃)₃?9H₂O, Co(NO₃)₂?6H₂O, ammonium hydroxide, and tetrapropylammonium hydroxide (TPAH). The synthesis was conducted in a sealed-vessel microwave reactor specifically designed for synthetic applications, and the resulting products were characterized by XRD, FE-SEM, TEM, and HR-TEM. After a systematic study of the influence of the microwave variables (temperature, reaction time and nature of the bases), highly crystalline CoFe₂O₄ nanoparticles with a high uniformity in morphology and size, were directly obtained by heating at 130?°C for 20?min using the base TPAH. Dense ceramics of cobalt ferrite were prepared by non-conventional, microwave sintering of synthesized nanopowders at temperatures of 850–900?°C. The magnetic properties of both the nanopowders and the sintered specimens were determined in order to establish their feasibility as a permanent magnet.