Highly porous YSZ ceramic foams using hollow spheres with holes in their shell for high-performance thermal insulation

Yttria-stabilized zirconia (YSZ) porous ceramic foams were fabricated using YSZ microspheres with holes on the surface to determine their properties as insulation materials. Highly porous YSZ ceramics with bimodal pore structures, such as internal pores in single hollow spheres and external pores between the spheres, were successfully prepared using YSZ spheres as raw materials. Additionally, holes were added to the shells to reduce continuous thermal pathways and significantly enhance the insulation properties. Furthermore, by adding holes on the surface of the sphere, the porous foams using a hollow sphere exhibit a maximized porosity of 80.69%, remarkably enhanced their insulation properties with low thermal conductivity (0.10 W/m-K), and have sufficient compressive strength to protect the green body (5.7 MPa). The mechanical strength of the YSZ porous foam was maintained owing to the uniform arrangement of the supports.     

Preparation and microstructure evolution of novel ultra-low thermal conductivity calcium silicate-based ceramic foams

In this study, municipal solid waste incineration fly ash (MSWI FA) was used as a new raw material for the ceramics industry and a novel ultra-low thermal conductivity calcium silicate-based foams (CSFs) was prepared by the direct foaming method. The effects of the addition of foam and borax on the sintering behavior and microstructural evolution of the CSFs were investigated. With the optimal amount of foam, the CSFs had an apparent porosity of 63.43%–67.49%, bulk density of 0.75–0.84 g/cm³, compressive strength of 1.83–3.21 MPa, and room-temperature thermal conductivity of 0.213–0.235 W/(m·K). Notably, the whisker morphology, pore structure, and sintering behavior of the samples can be controlled by changing the amount of borax. The prepared ceramic foams can be applied in the fields of thermal insulation, filtration, and catalyst carriers.     

Fabrication of in-situ self-reinforced Si3N4 ceramic foams for high-temperature thermal insulation by protein foaming method

To meet demand for lightweight and high-strength ceramic foams, in-situ self-reinforced Si₃N₄ ceramic foams, with compressive strength of 13.2–45.9 MPa, were fabricated by protein foaming method combined with sintered reaction-bonded method. For comparison, ordinary protein foamed ceramics with irregular block microstructure were fabricated via reaction-bonded method, which had compressive strength of 3.6–20.5 MPa. Physical properties of these two types of samples were systematically compared. When open porosity was about 80%, both types of Si₃N₄ ceramic foams had excellent thermal insulation properties (<0.15 W m^?1 K^?1), while compressive strength of in-situ self-reinforced samples increased by more than 158% compared with ordinary samples. Under high-temperature oxidation conditions, microstructures of both types of samples were deformed with increase in oxidation temperature. Moreover, after oxidation temperature was increased to 1400 °C, oxidation weight gain decreased from 18.07% for ordinary samples to only 2.18% for self-reinforced samples. Thus, high-temperature oxidation resistance of Si₃N₄ ceramic foams was greatly improved.     

Fabrication of novel BPO4 ceramic foams using the combination of the direct foaming method and freeze-drying techniques

In this study, ammonium phosphate monobasic and boric acid were used as the primary starting materials to produce BPO₄ powder by solid-state reaction. Using BPO₄ powders as the main raw material, BPO₄ ceramic foams were prepared for the first time using the direct foaming method and freeze-drying techniques. The effects of the additive content and solid loading on the slurry's rheological behavior were investigated, and the microstructures and properties of the as-prepared BPO₄ ceramic foams were examined. The results reveal that the porosity of the BPO₄ ceramic foams synthesized at 1223 K ranged from 84.2% to 90.4%, the compressive strength ranged from .12 MPa to .72 MPa, and the thermal conductivity ranged from .32 W/(m·K) to .74 W/(m·K) (298 K). The findings of this study have great significance for the development of new thermal insulation ceramic materials.     

Highly Porous Zirconia Ceramic Foams with Low Thermal Conductivity from Particle‐Stabilized Foams

Zirconia ceramic foams with ultra‐high porosity of 96%–98% have been fabricated using sodium dodecyl sulfate (SDS) as the particle stabilizer of zirconia particles for the first time. The wet foams stabilized by zirconia particles are ultra‐stable due to partially hydrophobic zirconia particles modified by SDS. Zirconia foams exhibit close cells with thin cell wall and small grain size. Increasing SDS concentration favors the foamability of the suspension, and further increases the porosity of ceramic foams. Zirconia ceramic foams with porosity of 98.1% have compressive strength of 0.26 ± 0.05 MPa. Decreasing solid loading leads to the porosity of ceramic foams. The compressive strength could be improved significantly by increasing the sintering temperature. Zirconia ceramic foams with porosity of 97.9% has low thermal conductivity of 0.027 ± 0.004 W·(m·K)^?1, which could be used as thermal insulation and refractory material.     

Ultrahigh-strength alumina ceramic foams via gelation of foamed boehmite sol

Ceramic foams with significant porosity and robust mechanical properties have received extensive attentions. However, it is still difficult to achieve excellent compressive strength at high porosity levels. In this work, a gelation of foamed boehmite sol method is proposed to settle this issue. The technological parameters during preparation process are systematically investigated. As-prepared alumina ceramic foams possess unprecedentedly high compressive strength of 34.1-89.1 MPa at high porosity levels of 66.0%-87.2%, which is attributed to the present of hierarchical pore structure, small grain size and pore size. This work demonstrates a facile and novel method for the fabrication of high-performance alumina ceramic foams toward practical applications.     

Mullite ceramic foams with tunable pores from dual-phase sol nanoparticle-stabilized foams

Particle-stabilized foams employing dual-phase sol of boehmite in combination with silica to prepare mullite ceramic foams has been proposed for the first time. The obtained mullite ceramic foams possess hierarchical pores, that is micropores derived from the air bubble templates and open windows formed by grain growth at thin area of pore wall according to the mullitization reaction. Furthermore, nanoparticles favor the improvement of specific surface area of ceramic foams, and wrinkles caused by drying shrinkage would retain when sintering at low temperature of 900℃-1100℃, leading to high specific surface area of 94.4-219.2 m²/g. The achieved mullite ceramic foams present relatively high compressive strength of 6.6?40.4 MPa at a high open porosity of 64.0 %–87.0 %, and their thermal conductivity could reach as low as 0.10 W/(m·K), which would make them promising lightweight materials applied in broad fields including thermal insulations, filters, bio-scaffolds, catalyst supports and the like.     

Highly porous silica foams prepared via direct foaming with mixed surfactants and their sound absorption characteristics

The highly porous silica ceramics were fabricated by direct foaming with mixed surfactants and the influence of silicon nitride addition and solid content on the microstructures and properties were investigated. The results showed that silicon nitride can impede the formation of cristobalite and facilitates the sintering of silica ceramics. When the addition of silicon nitride powders reached 15 wt%, the highest compressive strength of silica ceramic foams could be obtained. The porosity of silica ceramic foams was tailored in the range of 84.61%–91.35% by adjusting the solid content, and the compressive strength of the obtained ceramic foams ranged from 5.89 MPa to 0.94 MPa. Sound absorption characteristics of silica ceramics foams were investigated. With the porosity of ceramic foams increased from 84.61% to 91.35%, the sound absorption coefficients in the entire sound wave frequency were enhanced due to the reduction of flow resistances, besides, the sound absorption peak varied from 4200 Hz to 2300 Hz, and became more intense and sharper.     

Novel ZrP2O7 ceramic foams with controllable structures and ultra-low thermal conductivity

This study demonstrated the synthesis of novel zirconium pyrophosphate (ZrP₂O₇) ceramic foams via a two-step method using a foam casting technique. The synthesised foams functioned as thermal insulators with a highly controllable performance. We investigated the effects of the addition of foaming and thickening agents as well as the solid content of the slurries on the slurry, mechanical properties, thermal conductivities, and microstructure of ZrP₂O₇ ceramic foams. The ZrP₂O₇ ceramic foams synthesised at 1473 K exhibited a porosity, compressive strength, and thermal conductivity of 75.2–89.1 %, 1.95–0.02 MPa, and 0.144–0.057 W/(m K) (298–573 K), respectively. The increase in the porosity to >60 % will facilitate applications based on the low thermal conductivities of the foams.     

Effects of heating rate on the structure and properties of SiOC ceramic foams derived from silicone resin

Silicon oxycarbide ceramic foams were fabricated in a single step manufacturing process using in situ foaming of SiOC powders loaded silicone resin. The effects of heating rate on the porosity, compressive strength and microstructure of the ceramic foams were investigated. The porosity (total and open) increased firstly and then decreased with increasing heating rate. It was possible to control the total and open porosity of ceramic foams within a range of 81.9–88.2% and 62.4–72.5% respectively, by adjusting the heating rate from 0.25 °C/min to 3 °C/min while keeping the silicone resin content at 90 vol%. However, the compressive strength decreased with increasing the heating rate progressively, and the average compressive strength of the foams was in the range of 1.0–2.3 MPa. Micrographs indicated that the ceramic foams which cross-linked at a heating rate less than 1 °C/min had a well-defined open-cell and regular pore structure.     

Preparation,characterization, and physicomechanical properties of glass-ceramic foams based on alkali-activation and sintering of zeolite-poor rock and eggshell

This study reports the fabrication of novel glass-ceramic foams for thermal insulation to minimize the energy consumption in the buildings. Different combinations of zeolite-poor rock/eggshell powders (with eggshell content varying from 0 to 20 wt%) have been used to produce the foams through alkali-activation and reactive sintering techniques. The produced glass-ceramic foams were characterized based on their structural, thermal, and mechanical characteristics. The heat treatment process and the foaming patterns are examined by a heating microscope, and the findings reveal an excellent foamability of the utilized alkali-activated mixture in the range of 800–950 °C. The microstructure and the pore size of the acquired foams are investigated using a scanning electron microscope (SEM) and computed tomography (CT) analysis. The crystallinity and phase composition of the prepared samples were investigated via X-ray diffraction (XRD). The experiment findings reveal that raising the eggshell content is favorable to gas production, but it affects the liquid phase creation resulting in inconsistent pore size distribution. The appropriate eggshell content is 4%, and the optimal heat treatment temperature is 900 °C. The produced ceramic foams possess a density ranging from 0.54 to 1 g/cm³, thermal conductivity around 0.07–0.4 W/mK, and compressive strength values between 1.2 and 6.7 MPa. The results indicate that the ceramic foams created could be a feasible choice for applications in constriction as thermal insulation materials.     

Tailoring the microstructure of high porosity Si3N4 foams by direct foaming with mixed surfactants

The mixed surfactants were successfully applied to fabricate the highly porous Si₃N₄ ceramic foams by the direct foaming method. The oppositely charged surfactants mixed in slurries could combined into catanionic surfactant by the electrostatic attraction and facilitate the formation of ultra-stable foams. The microstructure of the Si₃N₄ ceramic foams, including pore structure, mean pore size, pore size distribution and porosity were tailored by varying the mixing ratio of surfactant, mixed surfactants concentration and solid content of the initial slurries. Si₃N₄ ceramic foams with porosity of 92%-97%, mean pore size of 140-240 µm and compressive strength of 0.85-5.38 MPa were obtained by adjusting mixed surfactants between 0.1 and 0.4 wt% and solid content between 22 and 30 vol%. The compressive strength of Si₃N₄ ceramic foams in current work was much higher than most reported results.     

Enhancing the thermal insulating properties of lanthanum zirconate porous ceramics via pore structure tailoring

The potentially useful role of lanthanum zirconate (La₂Zr₂O₇, LZO) porous bulk ceramics has been rarely explored thus far, much less the optimisation of its pore structure. In this study, LZO porous ceramics were successfully fabricated using a tert-butyl alcohol (TBA)-based gelcasting method, and the pore structures were tailored by varying the initial solid loading of the slurry. The as-prepared ceramics exhibited an interconnected pore structure with high porosity (67.9 %–84.2 %), low thermal conductivity (0.083–0.207 W/(m·K)), and relatively high compressive strength (1.56–7.89 MPa). The LZO porous ceramics with porosity of 84.2 % showed thermal conductivity as low as 0.083 W/(m·K) at room temperature and 0.141 W/(m·K) at 1200 °C, which is much lower than the counterparts fabricated from particle-stabilized foams owing to its unique pore structure with a smaller size, exhibiting better thermal insulating performance.     

Porous mullite ceramics with enhanced compressive strength from fly ash-based ceramic microspheres: Facile synthesis,structure, and performance

Porous mullite ceramics are widely used in heat insulation owing to their high temperature and corrosion resistant properties. Reducing the thermal conductivity by increasing porosity, while ensuring a high compressive strength, is vital for the synthesis of high-strength and lightweight porous mullite ceramics. In this study, ceramic microspheres are initially prepared from pre-treated high-alumina fly ash by spray drying, and then used to successfully prepare porous mullite ceramics with enhanced compressive strength via a simple direct stacking and sintering approach. The influence of sintering temperature and time on the microstructure and properties of porous mullite ceramics was evaluated, and the corresponding formation mechanism was elucidated. Results show that the porous mullite ceramics, calcined at 1550 °C for 3 h, possess a porosity of 47%, compressive strength of 31.4 MPa, and thermal conductivity of 0.775 W/(m?K) (at 25 °C), similar to mullite ceramics prepared from pure raw materials. The uniform pore size distribution and sintered neck between the microspheres contribute to the high compressive strength of mullite ceramics, while maintaining high porosity.     

Reticulated open-cellular aluminum nitride ceramic foams: Effect of sintering aids on microstructural,thermal, and mechanical properties

Open-celled aluminum nitride ceramic foams were prepared by the polymer sponge replication technique involving aqueous dispersions of passivated AlN. The amount of the Y₂O₃ and Dy₂O₃ as sintering aid was varied, and the effects on the densification, microstructure formation, phase composition, and finally, the thermal conductivity were investigated. A typical thermal conductivity of 1.1 W m⁻¹ K⁻¹ was determined for foams at a porosity level of 94.3 vol.%, on average. This measured foam thermal conductivity was subsequently modeled using different porosity ↔ thermal conductivity relations considering the different hierarchical levels of porosity in these foams. From these models, the thermal conductivity of the bulk AlN strut material was determined, correlated with the strut microstructure and the phase composition, and compared to literature data.     

Synthesis and characterization of porous Y2SiO5 with low linear shrinkage,high porosity and high strength

The emerging porous Y₂SiO₅ ceramic is regarded as a promising candidate of thermal insulator owing to its very low thermal conductivity. However, recent works on porous Y₂SiO₅ are confronted with severe problems such as large linear shrinkage (18.51–20.8%), low porosity (47.74–62%) and low strength (24.45–16.51 MPa) at high sintering temperatures (1450–1500 °C). In this work, highly porous Y₂SiO₅ ceramic with low shrinkage and excellent high-temperature strength was fabricated by in-situ foam-gelcasting method at 1550 °C. The as-prepared sample has unique multiple pore structures, low linear shrinkages of 6.3–4.5%, controllable high porosities of 60.7–88.4%, high compressive strengths of 38.2–0.90 MPa, and low thermal conductivities of 0.126–0.513 W/(m K) (porosity: 87.1–60.2%). The effects of relative density on relative strength, as well as porosity on thermal conductivity were quantitatively discussed. The present results indicate that porous Y₂SiO₅ is the potential high-temperature thermal insulation material of light weight, low thermal conductivity, and high strength.     

Sintering behaviour and characterisation of low-cost ceramic foams from coal gangue and waste quartz sand

New ceramic foams have been successfully synthesised with coal gangue and waste quartz sand, which supply a feasible way to recycle these hazardous solid wastes. An objective of this research was to investigate the sintering behaviour and effects of sintering conditions on the crystalline phase change, microstructure and main properties of final ceramic foams. Good correlations among porosity, thermal conductivity, water absorption, bulk density, mechanical properties were studied. Results indicated that increasing sintering temperature or time had similar effects on the physical–mechanical properties. Samples sintering at 1140°C for 1 hour exhibited the highest porosity (87.5%), lowest bulk density (0.39?×?10^?3?kg?m^?3), lowest thermal conductivity (0.085?W·(m?K)^?1), moderate water absorption (9.38%) and adequate flexible strength (2.4?MPa). Combined with excellent properties and low-cost characteristics, the new development for ceramic foams preparation will be widely used in building insulation materials for no-load bearing walls.     

Eggshells as agro-industrial waste substitute for CaCO3 in glass foams: A study on obtaining lower thermal conductivity

In this work, discarded glass bottles (GB) and eggshells (ES) were used to produce foam glass designed for thermal insulation. The literature on the thermal conductivity of foam glasses produced with eggshells is sparse. This material was used as pore-forming agent at 3% and 5% weight fractions to obtain a foam glass with low thermal conductivity. Homogenized powders were uniaxially pressed, and the compacts were fired at three temperatures (800, 850, and 900°C). Raw materials were characterized by chemical analysis and particle size distribution. The foam glasses were characterized by their porosity, phases, compressive strength, and thermal conductivity. The best insulating properties were obtained for the composition containing 5 wt% ES fired at 800°C. This sample displayed a porosity of 91.4% while its thermal conductivity was of 0.037 W/m.K, with a compressive strength of 1.12 ± 0.38 MPa. Crystalline phases were observed in samples fired at 850 and 900°C as a result of the devitrification process. The final properties of the materials are comparable to those of commercial foam glasses obtained from non-renewable, more expensive raw materials, a great indicator that the studied compositions could be used as an environmentally friendly substitute.     

New consolidation process inspired from making steamed bread to prepare Si3N4 foams by protein foaming method

A new consolidation process had been developed for preparing Si₃N₄ ceramic foams by using protein foaming method, which was inspired from the preparation of steamed bread. The main advantage of this consolidation process was no crack development during foamed slurry consolidation process. By using this new consolidation, Si₃N₄ ceramic foams with open porosities of 79.6–87.3% and compressive strength of 2.5–22 MPa were prepared. Protein addition and solid content on mechanical properties and pore structures of the as-prepared ceramic foams were investigated. Results indicated that the open porosity decreases with protein addition and solid content while compressive strength increased with solid content. With the increase of solid content, pores of the ceramic foams became regular in shape and uniform in size while both size and number of windows on the walls decreased.     

Lightweight porous silica-alumina ceramics with ultra-low thermal conductivity

Thermal protection has always been an important issue in the energy, environment and aerospace fields. Porous ceramics produced by the particle-stabilized foaming method have become a competitive material for thermal protection because of their low density and low thermal conductivity. However, the study of porous ceramics for composite systems using particle-stabilized foaming method was relatively rare. Here, silica-alumina composite porous ceramics were prepared by particle-stabilized foaming method, which was achieved by tailoring the surface charges of silica and alumina through adjustment of the pH. Porous ceramics exhibited porosity as high as 97.49% and thermal conductivity (25 °C) as low as 0.063 W m^?1 K^?1. The compressive strength of porous ceramics sintered at 1500 °C with a solid content of 30 wt% could reach 0.765 MPa. Based on the light weight and excellent thermal insulation properties, the composite porous ceramic could be used as a potential thermal insulation material in the spacecraft industry.