Slip casting of highly concentrated ZnO suspensions: Rheological studies,two-step sintering and resistivity measurements

The paper presents research on elaboration of well dispersed and stable aqueous suspensions of ZnO fine powder. Within the work the influence of the type and concentration (0.2 wt% - 1.2 wt%) of selected dispersing agents (i.a. poly(acrylic acid)-based polyelectrolyte and tetramethylammonium hydroxide), solid loading (30 - 50 vol%) and milling time (1–3 h) on the rheological properties of the slurries was investigated. Two-step sintering (970/920 °C, 2 h) was applied to sinter the green bodies obtained by slip casting.The lowest viscosity of ZnO suspensions was obtained for the addition of 0.4 wt% of poly(acrylic acid)-based polyelectrolyte (PAA) and TMAH. ZnO suspension containing PAA had negative zeta potential in the whole pH range. The highest solid loading obtained in the study was 50 vol%. The applied two-step sintering allowed to obtain samples of high density (above 96% of TD) and homogeneous microstructure of average grain size of 640 nm. ZnO sintered bodies were characterized by different electric properties at the core part and outer part of the sample which was caused by the differences in concentration of oxygen vacancies.     

Dispersion and densification of nano Si–(Al)–C powder with amorphous/nanocrystalline bimodal microstructure

The dispersion behavior and densification of nano Si–(Al)–C powder with amorphous/nanocrystalline bimodal microstructure were investigated. The Si–C powders synthesized by a mechanical alloying (MA) process had a near‐spherical shape with an average particle size of 170 nm. A solid loading of 62 vol% was achieved using polyethyleneimine (PEI) as a dispersant. The optimum dispersant amount was 1 wt% based on zeta potential, sedimentation, and viscosity analysis data. The high zeta potential value (73 mV) compared with that of the commercially available SiC (65 mV) was caused by modified surface properties and consequent promotion of the cationic dispersant adsorption. A Si–Al–C slurry containing 6.5 wt% of sintering additives with a solid loading of 60 vol% was also prepared. The relative density of the dried Si–Al–C slurry was 63.3% without additional compaction, which could be densified at 1650°C at a pressure of 20 MPa using a spark plasma sintering furnace.     

Solid solution synthesis of tantalum carbide‐hafnium carbide by spark plasma sintering

Solid solutions of Tantalum carbide (TaC) and Hafnium carbide (HfC) were synthesized by spark plasma sintering. Five different compositions (pure HfC, HfC‐20 vol% TaC, HfC‐ 50 vol% TaC, HfC‐ 80 vol% TaC, and pure TaC) were sintered at 1850°C, 60 MPa pressure and a holding time of 10 min without any sintering aids. Near‐full density was achieved for all samples, especially in the HfC‐contained samples. The porosity in pure TaC samples was caused by the oxygen contamination (Ta₂O₅) on the starting powder surface. The addition of HfC increased the overall densification by transferring the oxygen contamination from TaC surface and forming ultrafine HfO₂ and Hf‐O‐C grains. With the increasing HfC concentration, the overall grain size was reduced by 50% from HfC‐ 80 vol% TaC to HfC‐20 vol% TaC sample. The solid solution formation required extra energy, which restricted the grain growth. The lattice parameters for the solid solution samples were obtained using X‐ray diffraction which had an excellent match with the theoretical values computed using Vegard's Law. The mechanical properties of the solid solution samples outperformed the pure TaC and HfC carbides samples due to the increased densification and smaller grain size.     

Highly concentrated aqueous SiC slurry containing fine SiC powder: A new approach for ultra-dense green body

SiC slurry with ultra-high concentration up to 70 vol% was prepared using oxidized fine and coarse SiC powder mixture, and dense SiC green body with a relative density of 76% was fabricated by drying the slurry at ambient condition. Three approaches were performed to prepare highly concentrated SiC slurry; preparation of SiC powder having good dispersion behavior, optimization of the oxidation condition, and optimization of bi-modal particle size distribution. An aqueous slurry with the solid loading up to 62 vol% could be prepared using fine (150 nm) SiC powder prepared by the mechanical alloying of Si and carbon. The surface property of the fine and coarse (10 μm) SiC powders was optimized using an oxidation treatment. The maximum solid loading of the fine SiC slurry prepared using oxidized powder was 66 vol%. By optimizing the mixing ratio of the oxidized fine and coarse SiC powder to 75:25, the solid loading of the SiC slurry could increase up to 70 vol%. The relative densities of the green bodies after drying 66, 68, and 70 vol% slurries were 69, 75.7, and 76.1%, respectively, which values were higher than those (58%) prepared by cold isostatic pressing under 200 MPa.     

Preparation and properties of AlN ceramic suspension for non-aqueous gel casting

A non-aqueous gel casting process based on the mixed solvent (ethanol and polyethylene glycol) and low-toxicity N,N-dimethylacrylamide (DMAA) was developed for an aluminum nitride (AlN) ceramic. In the present work, rheological properties of non-aqueous concentrated AlN suspensions were investigated in the presence of mixed solvent, dispersant, milling time, monomer and solid loading, in order to screen for the most suitable experimental conditions to obtain a good rheological behavior for gel casting. The results showed that the 50 vol% slurry with 0.2 wt% dispersant concentration, 2 h milling time, 6 wt% -monomer content, and a solvent ratio of 3:1, can meet the requirements for the casting process of AlN ceramic slurries. After being dried at 100 °C for 1 h, the optimum bulk density and maximum flexural strength of the AlN green bodies were as high as 1.97 g/cm³ and 18.68 MPa, respectively. SEM photographs revealed that the green body had a relative uniform microstructure when the solid loading was 50 vol%. The shrinkage and deformation of shaped sintered bodies prepared through gel casting were small after sintering. The sintering shrinkage, apparent porosity, bulk density and flexural strength were 14.8%, 0.22%, 3.21 g/cm³ and 310 MPa, respectively.     

Freezing Dilute Ceramic/Camphene Slurry for Ultra-High Porosity Ceramics with Completely Interconnected Pore Networks

Highly porous alumina ceramics with completely interconnected pore channels were fabricated by freezing dilute alumina/camphene slurries with solid loadings ranging from 5 to 20 vol%. This method fundamentally made full use of the three-dimensional camphene dendritic network for producing interconnected pore channels and the concentrated alumina powder network for achieving dense alumina walls. Firstly, alumina/camphene slurries were prepared at 60°C using ball milling and then cast into molds at 20°C. After subliming the frozen camphene, the samples were sintered at 1400°C for 5 h. This method enabled us to freeze very dilute ceramic slurries with a low solid loading of ≤20 vol% without the collapse of the sample after sintering. As the initial solid loading decreased from 20 to 5 vol%, the porosity linearly increased from 66% to 90% with an increase in the pore size, while completely interconnected pore networks were obtained in all cases. In addition, the free surfaces of the alumina walls showed full densification after sintering even at a low temperature of 1400°C, while some pores were present in the inner regions of the alumina walls.     

Fabrication of transparent yttria ceramics by alcoholic slip-casting

Y₂O₃ transparent ceramics were prepared from alcoholic slurries of Y₂O₃ nanopowders via a slip-casting method to avoid the hydrolysis issue. Polyvinyl pyrrolidone (PVP), polyethylene glycol (PEG) and polyethylenimine (PEI) were used as dispersants to improve the rheological properties of the slurries. It was found that PEI is the most effective dispersant in ethanol. The adsorbed amount of PEI was evaluated by infrared absorption and rheology measurements. Y₂O₃ slurry with a solid loading of 20.8 vol% and a viscosity of <0.1 Pa s at the shear rate of 10 s⁻¹ was obtained using 1.5 wt% PEI. The slurry yielded a homogeneous green body, and finally resulted in a high-quality Y₂O₃ ceramic with the in-line transmittance of 80% at 800 nm.     

Dispersion Behavior of ZrB2 Powder in Aqueous Solution

Dispersion conditions of ZrB₂ powder in water were investigated using poly(ethyleneimine) (PEI) as a dispersant. Pulverization of ZrB₂ powder to submicrometer size was difficult and a substantial amount of large particles remained after an intensive planatery milling for 72 h. The isoelectric point (IEP) of ZrB₂ powder was measured to be pH 5.8 by electrophoresis, which shifted to pH 6.2 after milling. The application of PEI changed the IEP of the boride slurry to ∼pH 11. Well-dispersed aqueous ZrB₂ slurries with a high solid loading (up to 45 vol%) were fabricated at pH 6.5–7.5 by the application of 1.5 wt% PEI.     

A new direct coagulation casting process for alumina slurries prepared using poly(acrylate) dispersant

Direct coagulation casting (DCC) of concentrated aqueous alumina slurries prepared using ammonium poly(acrylate) dispersant has been studied using MgO as coagulating agent. Addition of small amounts of MgO increased the viscosity of the concentrated alumina slurries with time and finally transformed it in to a stiff gel. Sufficient working time for degassing and casting could be achieved by cooling the slurries to a temperature of ∼5 °C after proper homogenization after the addition of MgO. The DCC slip with alumina loading in the range of 50–55 vol% showed relatively low viscosity (0.12–0.36 Pa s at shear rate of 93 s⁻¹) and yield stress (1.96–10.56 Pa) values. The wet coagulated bodies prepared from slurries of alumina loading in the range of 50–55 vol% had enough compressive strength (45–211 kPa) for handling during mould removal and further drying. The coagulated bodies prepared from slurries of alumina loading in the range of 50–55 vol% showed linear shrinkage in the range of 4.8–2.3 during drying and 17.1–16.2 during sintering respectively. Near-net-shape alumina components with density >98% TD could be prepared by the DCC process.     

Influences of Solid Loadings on the Microstructures and the Optical Properties of Yb:YAG Ceramics

Transparent Y_2.85Yb_0.15Al₅O₁₂ ceramics were prepared using an aqueous tape casting and vacuum sintering method. The rheological properties were measured by a rheometer. The results indicate high quality tapes, and ceramics can be obtained by increasing the solid loading of the corresponding slurries. The densities of the tapes increase from 2.42 to 2.69 g/cm³ by increasing the solid loadings from 35 to 50 vol%. The corresponding green body densities range from 52.7 to 57.1% of the theoretical. The solid loading suitable for fabricating transparent Yb:YAG ceramics should be higher than 45 vol%.     

Effect of heat treatment on the dispersion and sintering behaviour of tin doped indium oxide powders

Due to the importance of structural uniformity of ITO targets on the properties of ITO films, the untreated and heat treated tin doped indium oxide powders were used to study the effects of four different dispersants on the dispersion behaviour of nanosized ITO powders. The optimum dispersant is NH₄PAA and its optimum amount is 1.00?wt% when the pH value is 9.0. In addition, the effect of the treatment temperature of nanosized ITO powders on the dispersion and sintering behaviour was also studied by SEM, TEM and XRD. The solid loading of ITO slurries and the relative density of the sintered bodies prepared with ITO powders treated at 900?°C could reach 40?vol% (untreated, 25?vol%) and 98.53% (untreated, 95.04%), respectively. The results indicate that the heat treatment of powders at 900?°C allowed obtaining powders from which ITO aqueous suspensions with high solid loading could be prepared and dense bodies after sintering. In another word, the appropriate heat treatment process for tin doped indium oxide powders could reduce the sintering temperature by 50?℃ and refine the grain size.     

Aqueous Gelcasting of Fused Silica Using Colloidal Silica Binder

An aqueous‐based gelcasting of fused silica ceramics by using colloidal silica binder was developed. Fused silica slurries having different volume percentage of solid loading from 63 to 74 vol% in colloidal silica were made and the rheological properties were evaluated. It was found that the slurry with 73 vol% of solid loading with viscosity 0.70 Pa.s is suitable for this gelcasting system. The influence of solid loading on physical and mechanical properties of gelcast green and sintered bodies has been studied. The fabricated green body by using colloidal silica binder exhibited a flexural strength of 9 MPa and 88% of theoretical density with 2.2% of drying shrinkage while the sintered sample exhibited flexural strength of 60 MPa and 95% of theoretical density with 4.3% of sintering shrinkage. It was observed that, the nano silica particles from the colloidal silica binder is filling the interstitial positions in the consolidated fused silica green body and enhancing physical and mechanical properties.     

Preparation,mechanical and thermal properties of Si3N4 ceramics by gelcasting using low–toxic DMAA gelling system and gas pressure sintering

In this work, Si₃N₄ ceramics were fabricated through an aqueous gelcasting method using a low–toxic monomer called N, N–dimethylacrylamide (DMAA) followed by gas pressure sintering at 1850 °C for 2 h under 6 MPa N₂ atmosphere. The effect of solid loading on performance of slurries, green and sintered bodies was investigated systematically. The results show that the slurries with a solid loading as high as 50 vol% (viscosity 0.17 Pa.s at 100 s^–1) were achieved. With the increase of solid loading (30–50 vol%), the green bodies exhibited a monotonically decreased, however high enough in general, flexural strength of 16.50–11.52 MPa, which was comparable to that of widely–used neurovirulent acrylamide (AM) gelling system. In regard to the sintered bodies, increasing solid loading significantly promoted sintering and improved mechanical properties and thermal conductivity as a result of the increased density, bimodal distribution structure, as well as suitable interfacial bonding strength. The best performance parameters of Si₃N₄ ceramics, bulk density of 3.25 g/cm³, apparent porosity of 0.67%, flexural strength of 898.92 MPa, fracture toughness of 6.42 MPa m^1/2, Vickers hardness of 2.81 GPa, and thermal conductivity of 34.69 W m^–1 K^–1, were obtained at 50 vol% solid loading. This work renders low–toxic DMAA gelling system promising prospect in preparation of high–performance Si₃N₄ ceramics by gelcasting.     

Low‐Temperature Sintering of HfC/SiC Nanocomposites Using HfSi2‐C Additives

HfC/SiC nanocomposites were fabricated via the reactive spark plasma sintering (R‐SPS) of a nano‐HfC powder and HfSi₂‐C sintering additives. The densification temperature decreased to 1750°C as the additive content increased. XRD analysis indicated the formation of pure HfC–(19.3–33.8 vol%) SiC within the sintered composites without residual silicide or oxide phases or secondary nonoxide phases. Ultrafine and homogeneously distributed HfC (470 nm) and SiC (300 nm) grains were obtained in the dense composites using nano‐HfC powder through the high‐energy ball‐milling of the raw powders and R‐SPS. Grain growth was further suppressed by the low‐temperature sintering using R‐SPS. No amorphous phase was identified at the grain boundary. The maximum Vickers hardness, Young's modulus, and fracture toughness values of the HfC/SiC nanocomposites were 22 GPa, 292 GPa, and 2.44 MPa·m^1/2, respectively.     

Direct coagulation casting of silicon carbide suspension via polyelectrolyte dispersant crosslink reaction

A direct coagulation casting method for silicon carbide ceramic suspension using dispersant crosslink reaction is reported. Polymer electrolyte (polyethyleneimine, PEI) was used as dispersant to prepare silicon carbide suspension. Common food additives (carboxymethyl cellulose, CMC) were used to coagulate the electrosteric stabilized silicon carbide suspension. There was a well disperse silicon carbide suspension with 0.2 wt% PEI at pH = 5-6. Influence of coagulant on viscosity and zeta potential of the silicon carbide suspension was investigated. It indicates that the high solid loading silicon carbide suspension can be destabilized and coagulated at elevated temperature. It can be attribute to the gradual decrease of electrosteric force due to the crosslink reaction between PEI and CMC. Silicon carbide wet green body with compressive strength of 1.99 MPa could be demolded at 70°C which is higher than that prepared by traditional DCC and dispersant reaction method for nonoxide ceramics. Dense silicon carbide ceramics with relative density above 98.8% and 99.3% had been prepared by liquid phase pressureless and hot pressed sintering, respectively.     

Photocurable ceramic slurry using solid camphor as novel diluent for conventional digital light processing (DLP) process

This study presents the utility of solid camphor as a novel type of diluent for the preparation of photocurable ceramic slurries with sufficiently low viscosity at high solid loading (48 vol%), which can be applicable for the conventional digital light processing (DLP) process. The camphor addition remarkably decreased the viscosity of calcium phosphate (CaP) ceramic slurries without affecting their photopolymerization behavior. This approach could effectively mitigate the clogging of pores with residual slurries, and thus the porous structure of porous CaP scaffolds with 3D channels could be tightly controlled. Furthermore, the high densification of CaP frameworks after sintering at 1250 °C for 3 h could be achieved owing to the use of the high solid loading in the CaP slurry. The porous CaP scaffolds produced displayed high compressive strength (˜ 23.8 MPa) and modulus (˜ 276 MPa) at a high porosity of ˜ 50.6 vol%.     

Effect of solid loading on properties of Y2O3–Al2O3–Nd2O3 powder mixtures obtained by planetary ball milling and ceramics based on them

The effect of the solid loading (41–50 wt%) of the slurry on granulometric composition and physico-chemical characteristics of Y₂O₃–Al₂O₃–Nd₂O₃ powder mixtures obtained by planetary ball milling has been studied for the first time. It was shown that the particle size distribution of powder, its Zeta potential, and specific surface area depend on the solid loading of the milled slurry and, consequently, on the interparticle distance during milling. The interparticle distance decreases from 200 nm to 142 nm with an increase of solid loading in the range of 41–50 wt%. It was shown that for the solid loading of 47 wt%, the convergence of particles to a distance comparable to their median diameter promotes subsequent clustering of particles. This facilitates the sintering of highly-homogenous ceramics. It was found that solid loadings in the 46–50 wt% range is useful for obtaining high-quality Nd:YAG transparent ceramics. The lowest optical losses optical losses of 1 × 10^?3 cm^?1 and the highest in-line transmittance of 84.1%@1064 nm were obtained for 1 at.% Nd:YAG transparent ceramics (22 × 3 × 4 mm³) prepared from slurries with 47 wt% solid loading (taking all other ball milling parameters fixed). If the interparticle distance in the powder is higher (solid loading of 41 wt%) than the median particle diameter, the ceramics are characterized by significant residual porosity due to the survival of large particles (insufficient milling).     

Aqueous Tape Casting of Zirconium Diboride

Aqueous tape casting of ZrB₂ powder with sintering additives was investigated. The dispersion of ZrB₂ suspensions in aqueous media was studied and characterized in terms of zeta potential, sedimentation, and rheological measurements. A well-stabilized suspension with a high solid content (up to 45 vol%) was prepared in the alkaline pH region with 0.4 wt% Lopon 885 as the dispersant. Several suspensions with different compositions of binder and plasticizer were prepared for comparison. Crack-free green tapes with a maximum thickness of approximately 250 μm were obtained with a binder content of 18–23 wt%. The green tapes had high qualities, such as homogeneity, good flexibility, and a smooth surface. Results showed that the slurries at selected formulations met the needs of the tape-casting process.     

Additive manufacturing of SiC-Sialon refractory with excellent properties by direct ink writing

Additive manufacturing of SiC-Sialon refractory with complex geometries was achieved using direct ink writing processes, followed by pressureless sintering under nitrogen. The effects of particle size of SiC powders, solid content of slurries and additives on the rheology, thixotropy and viscoelasticity of ceramic slurries were investigated. The optimal slurry with a high solid content was composed of 81 wt% SiC (3.5 µm+0.65 µm), Al₂O₃ and SiO₂ powders, 0.2 wt% dispersant, and 2.8 wt% binder. Furthermore, the accuracy of the structure of specimens was improved via adjustment of the printing parameters, including nozzle size, extrusion pressure, and layer height. The density and flexural strength of the printed SiC-Sialon refractory sintered at 1600 °C were 2.43 g/cm³ and 85 MPa, respectively. In addition, the printed SiC-Sialon crucible demonstrated excellent corrosion resistance to iron slag. Compared to the printed crucible bottom, the crucible side wall was minimally affected by molten slag.     

Dispersion of SiC in Aqueous Media with Al2O3 and Y2O3 as Sintering Additives

It has been well accepted that polyethylene imine (PEI) is an effective dispersant for silicon carbide (SiC) in aqueous media. However, after the addition of sintering additives (Al₂O₃ and Y₂O₃), this dispersing effect is reduced significantly. In this work, a second dispersant, citric acid, was used to resolve this problem. It was found that citric acid could decrease the slurry viscosity (without sintering additives) and enhance the PEI adsorption on SiC particle surface. The optimal amount of citric acid required to achieve a minimum viscosity for 55 vol% SiC suspensions was equal to ∼0.87 wt% (at pH ∼6.8). With the aid of citric acid, well-stabilized SiC suspensions (containing sintering additives) were realized, which exhibited slight shear thinning rheologies. After tape casting and SPS sintering, dense SiC samples were obtained with a homogeneous fine-crystalline microstructure. Results showed that citric acid was an effective dispersant for improving the dispersion of SiC particles containing sintering additives.