Chemical Interaction Between LiF and MgAl2O4 Spinel During Sintering

Reactions between LiF and MgAl₂O₄ at temperatures up to 1500°C are examined with a variety of tools, including differential scanning calorimetry, thermo-gravimetric analysis, X-ray diffraction, and scanning electron microscopy. LiAlO₂ and MgF₂ are found to be the active reaction products at these temperatures. A transient liquid phase comprising MgF₂ and LiF forms at intermediate temperatures, but then is consumed at higher temperatures during the reformation of MgAl₂O₄. If processed as an uncompacted powder mixture, all of the initial LiF in the system eventually vaporizes at temperatures exceeding 1300°C. A new reaction sequence relevant to the densification of LiF-doped MgAl₂O₄ spinel is proposed.     

Ternary System Al2O3-MgO-CaO: I, Primary Phase Field of Crystallization of Spinel in the Subsystem MgAl2O4-CaAl4O7-CaO-MgO

Using a novel experimental procedure in the field of ceramics/materials science that is based on the precise microanalysis (scanning electron microscopy, coupled with wavelength-dispersive spectroscopy) of the phases that are present in equilibrated specimens, the solid-state compatibility relations in the subsystem MgAl₂O₄-CaAl₄O₇-CaO-MgO and the melting relationships in the subsystems MgAl₂O₄-CaAl₂O₄-MgO and MgAl₂O₄-CaAl₂O₄-CaAl₄O₇ were established. The primary phase field of crystallization of spinel in the above-mentioned subsystem, MgAl₂O₄-CaAl₄O₇-CaO-MgO, was determined subsequently. The temperature, composition, and character of the ternary invariant points of the subsystem were established, and the ranges of the solid solutions in periclase, spinel, monocalcium aluminate, and dicalcium aluminate also were studied and determined, up to 1725°C.     

Growth of Single-Crystal and Polycrystalline Thin Films of MgAl2O4 and MgFe2O4

Single-crystal and polycrystalline films of Mg-Al₂O₄ and MgFe₂O₄ were formed by two methods on cleavage surfaces of MgO single crystals. In one procedure, aluminum was deposited on MgO by vacuum evaporation. Subsequent heating in air at about 510°C formed a polycrystalline γ-Al₂O₈ film. Above 540°C, the γ-Al₂O, and MgO reacted to form a single-crystal MgAl₂O₄ film with {001} MgAl₂O₄‖{001} MgO. Above 590°C, an additional layer of MgAl₂O₄, which is polycrystalline, formed between the γ-Al₂O₃ and the single-crystal spinel. Polycrystalline Mg-Al₂O₄ formed only when diffusion of Mg²⁺ ions proceeded into the polycrystalline γ-Al₂O₃ region. Corresponding results were obtained for Mg-Fe₂O₄. MgAl₂O₄ films were also formed on cleaved MgO single-crystal substrates by direct evaporation, using an Al₂O₃ crucible as a source. Very slow deposition rates were used with source temperatures of ∼1350°C and substrate temperatures of ∼800°C. Departures from single-crystal character in the films may arise through temperature gradients in the substrate.     

Preparation of MgAl2O4 Spinel Powders via Freeze-Drying of Alkoxide Precursors

High-sinterability MgAl₂O₄ powder has been produced from alkoxide precursors via a freeze-drying method. Clear alumina sol and magnesium methoxide were used as starting materials in the process. The spinel powders were characterized by various techniques, such as thermal analysis, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The tap density and sinterability of the spinel power are affected by the ball-milling techniques. Highly dense, transparent, polycrystalline MgAl₂O₄ has been obtained from these powders by sintering and hot isostatic pressing. Bimodal grain-size microstructure is observed in a HIPed sample.     

Coherent Precipitation in the System MgO-Al2O3-Cr2O3

An isothermal section of the ternary system MgO–Al₂O₃-Cr₂O₃ was determined at 1700°± 15°C to delineate the stability field for spinel crystalline solutions (cs). Crystalline solutions were found between the pseudobinary joins MgAl₂O₄–Cr₂O₃ and MgCr₂O₄-Al₂O₃, and the binary join MgAl₂O₄-MgO. The first two crystalline solutions exhibit cation vacancy models while the latter can probably be designated as a cation interstitial model. Precipitation from spinel cs may proceed directly to an equilibrium phase, (Al_1-xCr_x)₂O₃, with the corundum structure or through a metastable phase of the probable composition Mg(Al_1-xC_r)₂₆O₄₀. The composition and temperature limits were defined where the precipitation occurs via metastable monoclinic phases. The coherency of the metastable monoclinic phase with the spinel cs matrix can be understood by considering volume changes with equivalent numbers of oxygens and known crystallographic orientation relations. Electron probe and metallographic microscope investigations showed no preferential grain boundary precipitation.     

Modification of MgAl2O4 Microwave Dielectric Ceramics by Zn Substitution

MgAl₂O₄ microwave dielectric ceramics were modified by Zn substitution for Mg, and their dielectric characteristics were evaluated, along with their structures. Dense (Mg_{1− x} Zn _x )Al₂O₄ ceramics were obtained by sintering at 1550°–1650°C in air for 3 h, and the (Mg_{1− x} Zn _x )Al₂O₄ solid solution was determined in the entire composition range. With Zn substitution for Mg, the dielectric constant ɛ of MgAl₂O₄ just varied from 7.90 to 8.56, while the Q × f value had significantly improved up to a maximal value of 106 000 GHz at x =1.0. Moreover, the τ_f of MgAl₂O₄ ceramics had declined from −73 to −63 ppm/°C.     

TEM Characterization of Nanostructured MgAl2O4 Synthesized by a Direct Conversion Process from γ-Al2O3

Nanostructured MgAl₂O₄ spinel was synthesized by a direct conversion process from cubic γ-Al₂O₃. The effect of post-annealing temperature (300°, 500°, and 800°C) on MgAl₂O₄ phase formation was investigated using transmission electron microscopy, selected area electron diffraction (SAED), electron energy loss spectroscopy (EELS), and energy-dispersive spectroscopy (EDS). Relative diffraction intensities as well as lattice parameter measurements from SAED revealed that MgAl₂O₄ spinel structure starts forming at temperatures as low as 300°C. EELS and EDS spectrum images also revealed an increase in elemental homogeneity with increasing annealing temperature. The degree of ordering of Mg and Al between octahedral and tetrahedral sites has been determined from relative diffraction intensities. Results show that annealing to 800°C leads to a spinel phase with an order parameter of 0.78.     

Exsolution of β-Ga2O3 Crystalline Solutions in the System MgAl2O3-Ga2O3

The subsolidus phase equilibrium diagram for the pseudobinary join MgAl₂O₄-Ga₂O₃ was determined. The shape of the exsolution boundary was obtained by heat-treating samples pre- equilibrated at 1600°C. Crystalline solubility of Ga₂O₃ in MgAl₂O₄ decreased from 73 mole % at 1600°C to 55 mole % at 1200°C. The crystalline solution was formed by the replacement of Mg²⁺ions by Ga³⁺ ions to produce a cation defect spinel. The phase precipitated was the mono-clinic δ-Ga₂O₃ (=δ-Al₂O₃ structure). Changes in the ratios of relative X-ray diffraction intensities indicated that the crystalline solutions also disorder with temperature.     

Quaternary System Al2O3–CaO–MgO–SiO2: II Study of the Crystallization Volume of MgAl2O4

Solid-state compatibility and melting relations of MgAl₂O₄ in the quaternary system Al₂O₃–CaO–MgO–SiO₂ were studied by firing and quenching selected samples located in the 65 wt% MgAl₂O₄, plane followed by microstructural and energy dispersive X-ray analysis. A projection of the liquidus surface of the primary crystallization volume of MgAl₂O₄ was constructed from CaO, SiO₂ and exceeding Al₂O₃, not involved in stoichiometric MgAl₂O₄ formation; those three amounts were recalculated to 100 wt%. The temperature and character of six invariant points, where four solids co-exist with a liquid phase, were defined. One maximum point was localized and the positions of the isotherms were tentatively established. The effect of CaO, SiO₂, and Al₂O₃ impurities on the high temperature behavior of spinel materials was also discussed.     

High-Strain-Rate Superplasticity in Y2O3-Stabilized Tetragonal ZrO2 Dispersed with 30 vol% MgAl2O4 Spinel

High-strain-rate superplasticity is attained in a 3-mol%-Y₂O₃-stabilized tetragonal ZrO₂ polycrystal (3Y-TZP) dispersed with 30 vol% MgAl₂O₄ spinel: tensile elongation at 1823 K reached >300% at strain rates of 1.7 × 10⁻²– 3.3 × 10⁻¹ s⁻¹. The flow behavior and the microstructure of this material indicate that the MgAl₂O₄ dispersion should enhance accommodation processes necessary for grain boundary sliding. Such an effect is assumed to arise from an enhancement of the cation diffusion by the dissolution of Al and Mg ions into the ZrO₂ matrix and from stress relaxation due to the dispersed MgAl₂O₄ grains.     

Translucent Sintered MgAl2O4

A translucent polycrystalline MgAl₂O₄ ceramic was prepared from finely divided coprecipitated spinel in which a small amount of CaO added as a sintering aid was uniformly distributed. The CaO promotes densification through the formation of a liquid phase at the sintering temperatures. Depending on the sintering treatment, the relative density of the sintered spinel was 99.7 to ∼100% of theoretical. The in-line optical transmission was > 10% from 0.3 to 6.5 μm. Total transmission in the visible region was between 67 and 78%.     

Electrochemical Determination of the Gibbs Energy of Formation of MgAl2O4

The standard Gibbs energy of formation of the spinel MgAl₂O₄ from component oxides, MgO and α-Al₂O₃, has been determined in the temperature range 900 to 1250 K using a solid-state cell incorporating single-crystal CaF₂ as the solid electrolyte. The cell can be represented as—Pt,O₂,MgO+MgF₂|CaF₂|MgF₂+MgAl₂O₄+α-Al₂O₃,O₂,Pt—The standard Gibbs energy of formation from binary oxides, computed from the reversible emf, can be represented by the expression—capdelta G °_f,ox=−23600 − 5.91 T (±150) J/mol—The 'second-law' enthalpy of formation of MgAl₂O₄ obtained in this study is in good agreement with high-temperature solution calorimetric studies reported in the literature.     

Molten Salt Synthesis of Magnesium Aluminate (MgAl2O4) Spinel on Ti3AlC2 Substrate

A MgAl₂O₄ (MA) spinel layer was synthesized on Ti₃AlC₂ substrate through the molten salt synthesis (MSS) method. The Ti₃AlC₂ substrate was immersed in MgCl₂·6H₂O powders and treated at 800°, 850°, and 900°C for 4 h in air. A continuous and 10-μm-thick MgAl₂O₄ layer was obtained at 900°C, by which the surface hardness of Ti₃AlC₂ can be effectively improved. The combined scanning electron microscopy observations and crystal morphology simulation further revealed that the as-formed MgAl₂O₄ presents tetragonal bipyramids morphology with (400)-orientation.     

Thermochemistry of MgAl2O4-Al8/3O4 Defect Spinels

Solution calorimetry of MgAl₂O₄-Al_8/3O₄ solid solutions was performed in a molten 2PbO · B₂O₃ solvent at 975 K. The results indicate small negative heats of mixing, relative to spinel standard states for both end-members. These data were combined with information on the energetics of the α-γ transition in Al₂O₃ and on the MgAl₂O₄-Al_8/3O₄ (MgO-Al₂O₃) subsolidus phase relations to estimate the partial molar entropy of mixing of γ-Al_8/3O₄ in the solid solution. This entropy is much less positive than that calculated from several models for the configurational entropy of mixing of magnesium, aluminum, and vacancies on octahedral and/or tetrahedral sites. The data suggest a good deal of local order to be present in the solid solutions, consistent with negative enthalpies of mixing and entropies of mixing far less than ideal configurational values.     

Investigation of High-Alumina Spinel: Effect of LiF and CaCO3 Addition

This work examines the effects of LiF or LiF/CaCO₃ additives on the phases, microstructure, sintering temperature, and activation energy of MgO-Al₂O₃ spinel formation. According to these results, the spinel formation temperature decreases and the spinel phase content increases by incorporating sintering additives. Such an effect is due to the formation of liquid phases at sintering temperatures. The Al composition in spinel is substantially higher in samples containing LiF or LiF/CaCO₃ than in samples without sintering additives. Results obtained from the Arrhenius equation and Jander's model indicate that the activation energy for forming spinel decreases by incorporating LiF or LiF/CaCO₃.     

Reactive Synthesis of a Porous Calcium Zirconate/Spinel Composite with Idiomorphic Spinel Grains

Porous CaZrO₃/MgAl₂O₄ composites were synthesized in air by pressureless reactive sintering of an equimolar mixture of dolomite (CaMg(CO₃)₂), monoclinic zirconia ( m -ZrO₂), and α-alumina powders, with a 0.5 wt% lithium fluoride additive. The reaction behavior of the mixed powders (with/without LiF additive) was studied using high-temperature X-ray diffraction. A bulk porous composite resulted from sintering at 1300°C for 2 h (in a nearly closed container, so as to increase the LiF-doping effect), which consisted of fine grains (CaZrO₃ and MgAl₂O₄, ∼0.5–1 μm) and well-grown idiomorphic ones (MgAl₂O₄ octahedra ∼ 2–4 μm). The idiomorphic spinel grains were located around the inner walls of relatively large pores. The composite showed appreciably high bending strength (σ_f= 110 ± 8 MPa for a porosity of 31%). The porous CaZrO₃/MgAl₂O₄ composites can be applied as high-temperature filters and lightweight structural components.     

Optical Spectra of Synthetic Spinels in the System MgAl2O4–MgCr2O4

Unpolarized optical spectra were measured in the wavelength range 322–1666 nm by the diffuse reflection technique from spinel powders synthesized in the system MgAl₂O₄–MgCr₂O₄. The spectra were interpreted by the crystal-field theory on the basis of trigonally distorted spinel octahedra with D_3d symmetry. For chromium-rich solid solutions, including the MgCr₂O₄ end-member, results after peak fittings showed octahedral D_3d local symmetry around Cr³⁺ ions, identical to the crystallographic site symmetry. For chromium-poor solid solutions, however, octahedral C_3v local symmetry was suggested around Cr³⁺ ions, different from the D_3d crystallographically expected.     

Synthesis and Characterization of MgAl2O4 Spinel Precursor from a Heterogeneous Alkoxide Solution Containing Fine MgO Powder

A precursor was synthesized from a heterogeneous alkoxide solution that contained fine MgO powder, which allowed the preparation of MgAl₂O₄ spinel powder with high sinterability characteristics. The precursor consisted of a mixture of boehmite (AlO(OH)) and a mixed hydroxide (Mg₄Al₂(OH)₁₄· 3H₂O). The spinel phase formed through two steps: (i) decomposition of the mixed hydroxide at low temperature and (ii) solid-state reaction between MgO and γ-Al₂O₃ at higher temperatures. Dense polycrystalline spinel could be obtained from the calcined powders at sintering temperatures as low as 1400°C.     

Low-Temperature Chemical Synthesis of Nanocrystalline MgAl2O4 Spinel Powder

Nanocrystalline MgAl₂O₄ spinel powder was synthesized by pyrolysis of complex compounds of aluminum and magnesium with triethanolamine (TEA). The soluble metal ion–TEA complexes formed the precursor material on complete dehydration of the complexes of aluminum–TEA and magnesium–TEA. Single-phase MgAl₂O₄ spinel powder resulted after heat treatment of the precursor material at 675°C. The precursor and the heat-treated powders were characterized by X-ray diffractometry (XRD), differential thermal and thermogravimetric analysis, and transmission electron microscopy (TEM). The average crystallite size as measured from the X-ray line broadening was around 14 nm and the average particle size from TEM studies was around 20 nm.     

Mechanical Activation of Heterogeneous Sol–Gel Precursors for Synthesis of MgAl2O4 Spinel

MgAl₂O₄ spinel precursor was prepared using a heterogeneous sol–gel process. The effect of high-energy milling on the precursor decomposition and spinel formation was investigated. The milling decreased the Al(OH)₃ dehydroxylation temperature from 190° to about 130°C. The activation energy for spinel formation decreased from 688 kJ/mol for the as-prepared precursors to 468 kJ/mol for the precursors milled for 5 h. Milling of the precursor lowered the incipient temperature of spinel formation from 900° to 800°C, and the temperature of complete MgAl₂O₄ spinel formation from >1280° to ∼900°C.