调控晶粒尺寸合成高渗透ZSM-5沸石膜

用原位水势合成法,在170℃下通过调控不同的晶粒尺寸在α-Al2O3陶瓷管上合成ZSM-5沸石膜,用XRD,SEM对膜进行表征,表明生成致密的ZSM-5沸石膜;对膜进行单气体渗透量测试,膜的H2渗透量3.69×10-6mol/(m2·s·Pa),H2/C3H8的理想分离因子为25 6.     

ZSM—5沸石膜的合成与表征

叙述了沸石膜的发展与应用,综述了 Ｚ Ｓ Ｍ － ５ 沸石膜的合成、修饰与表征方法．制备膜最常用的方法为水热法在载体上直接就地合成．气相化学沉积法（ Ｃ Ｖ Ｄ） 、溶胶－ 凝胶法（ｓｏｌ － ｇｅｌ） 以及合成后积炭等方法被用来对膜的缺陷进行修饰．膜的表征手段为 Ｘ Ｒ Ｄ、 Ｓ Ｅ Ｍ、气体渗透等     

纳米ZSM-5沸石合成方法及应用

ZSM-5沸石由于其特殊的孔道结构以及高的硅铝比，具有优良的稳定性，被广泛用作催化剂。将ZSM-5沸石纳米化后，其应用途径更为宽阔。本文首先介绍了几种常见纳米沸石的合成方法，并在此基础上介绍了ZSM-5沸石的合成和应用。     

ZSM—5型沸石膜的合成及应用于乙苯脱氢反应研究进展

重点介绍了国内外关于ZSM－5沸石膜的合成及应用于乙苯脱氢反应应用现状,分析和阐述了当今ZSM－5沸石膜合成的方法和特点及今后面临的挑战。     

Obtainment of hierarchical ZSM-5 zeolites by alkaline treatment for the polyethylene catalytic cracking

Great efforts have been applied in order to achieve the synthesis of hierarchical zeolites through post-synthesis alkaline treatment. In this case, the use of hierarchical ZSM-5 zeolites as acid catalysts in the catalytic cracking of polyolefins overcomes some diffusional limitations and expands the selectivity of products. Thus, the purpose of work was to promote a secondary porosity in ZSM-5 zeolite by NaOH treatment (using conventional electric and microwave heating methods), applying cetyltrimethylammonium bromide as pore-directing agent. Both heating methods generated additional secondary porosity, with microwave heating promoting a narrow pore size distribution, when compared to conventional. All hierarchical ZSM-5 have been showed low-density polyethylene conversions superior to the purely microporous ZSM-5, however the hierarchical zeolite processed by conventional electric heating reached the higher temperature reduction (42.6 K). It was evidenced through measurements of morphological and textural properties, ion exchange capacity and catalytic activity in the LDPE cracking that the CTAB cations exerts a protective effect at alkaline treatment avoiding the desilication process. The additional secondary porosity promoting the generation of compounds of lower molecular mass in LDPE catalytic cracking, by thermogravimetric analysis, proving that the alkaline treatment increases the accessibility to the active acidic sites of zeolitic catalysts for bulky molecules.     

Study on using cellulose derivatives as pore directing agent for preparation of hierarchical ZSM-5 zeolite catalyst

Cellulose derivatives such as hydroxyethylmethylcellulose (HEMC), and hydroxypropylmethylcellulose (HPMC), which are originated from biomass, were used as mesoporous directing agent for the synthesis of hierarchical ZSM-5 zeolite. Hierarchical ZSM-5 zeolites with outstanding mesoporosity and high hierarchy factors were achieved by hydrothermal method in the presence of bio-mesoporogen. The as-synthesized hierarchical ZSM-5 zeolites were characterized by X-ray diffraction (XRD), nitrogen adsorption–desorption (BET), scanning electron microscope (SEM) to determine the structure of samples. The influences of different mesoporogens with different dosage in the synthetic process on the physicochemical and catalytic properties of hierarchical ZSM-5 zeolite were investigated. Possession of the high mesopores, high surface areas and abundant accessible acid sites, the hierarchical zeolites exhibited excellent catalytic performance in the alkylation reaction of benzene and benzyl alcohol.     

ZSM-5沸石分子筛的高压吸附储氢特性

研究了ZSM-5沸石分子筛对氢的超临界吸附特性．结果表明,在77K／5MPa、195K／7MPa、293K／7MPa条件下,ZSM-5沸石分子筛的储氢质量分数分别为1．97％、0．65％和0．4％．用Clausius-Clapeyron方程求得的等量吸附热（3．8kJ／mol）与吸附量无关,表明该分子筛是一种表面势场均匀的吸附剂．将表面过剩吸附理论与描述Ⅰ型等温线的诸理论模型结合,分析了超临界吸附等温线,发现基于Toth方程的等温线模型在整个实验范围内与实验数据吻合较好,由该模型计算出的氢吸附相密度在77K达到55．6kg／m^3．根据回归参数讨论了超临界条件下氢在微孔沸石分子筛中的吸附机理,确认了氢在微孔沸石分子筛中的吸附为物理吸附．     

具有特殊形貌ZSM5分子筛的控制合成

采用水热合成的方法,以硅溶胶为硅源,分别以四丙基溴化铵(TPABr)和四丙基氢氧化铵(TPAOH)为模板剂,得到了不同尺寸和形貌的ZSM-5分子筛,采用X射线衍射(XRD)和扫描电镜(SEM)对分子筛样品进行了表征。结果表明:以TPABr为模板剂时,通过改变水含量,可制备出较高结晶度具有成束的棒状、花瓣形的片状和微米尺度的球状ZSM-5分子筛;以TPAOH为模板剂时,随乙醇用量增加,合成的分子筛结晶度逐渐提高,晶粒尺寸和形貌变化大,当乙醇与SiO2物质的量比为1.9时得到结晶度高、形貌均一、尺寸1~2μm、六角板状的ZSM-5分子筛。     

ZSM-5分子筛介孔的构筑

在微孔结构的ZSM-5沸石分子筛中构筑介孔,可以有效地解决ZSM-5分子筛在催化反应过程中的扩散传质和催化剂失活问题.重点阐述了在初始的合成体系中加入炭黑、介孔碳、表面活性剂等作为模板剂来构筑含介孔结构的ZSM-5和利用碱液或酸液对已合成的微孔的ZSM-5进行后处理来构筑介孔,并对含有介孔结构的ZSM-5的性质和相关的应用做了评价和展望.     

高通量ZSM-5填充硅橡胶复合膜渗透汽化性能研究

以硅铝比为360的ZSM-5型沸石对聚二甲基硅氧烷(PDMS)进行填充,以聚偏氟乙烯(PVSF)为支撑层,制备了ZSM-5填充PDMS/PVDF复合膜,用于渗透汽化乙醇/水混合物的分离.研究了沸石填充量、操作温度、进料液浓度对乙醇/水的渗透汽化分离性能的影响,发现该复合膜较文献报道中的沸石填充膜,其渗透通量有了明显的提高,在50℃沸石填充量为40%时,对乙醇的分离因子为11.7,其渗透通量达到749.8 g/(m2·h).随着操作温度的升高或料液中乙醇浓度升高,渗透通量增大,分离因子下降.     

二次生长法中ZSM-5型沸石分子筛膜合成规律的研究

采用正交试验法,考察了ZSM-5沸石膜合成过程中,制膜液碱量、膜板剂的用量、晶种的引入方式等对成膜的影响;确定了采用浸涂法引入晶种,晶化液摩尔组成为n(Na2O)∶n(Al2O3)∶n(SiO2)∶n(TPABr)∶n(H2O)=15∶1∶100∶20∶10 000,在180℃,晶化48 h,可在多孔α-Al2O3陶瓷管支撑体外表面合成了ZSM-5沸石分子筛膜.用XRD,SEM和单组分气体的渗透对膜进行了表征.结果表明,所合成的沸石膜是典型的ZSM-5沸石膜,膜表面晶粒生长发育较完整,排列紧密,无较大裂缺;H2,N2在膜内的渗透率分别为4.51×10-6,1.34×10-6mol/(m2.s.Pa);膜的H2/N2理想分离因数为3.37.     

一步合成核壳结构ZSM-5/EU-1复合分子筛及其表征

在添加适量柠檬酸的条件下采用双模板剂一步法, 一次晶化合成ZSM-5/EU-1核壳共生复合分子筛, 对其物理化学性质进行表征, 结果显示: 核壳分子筛中存在ZSM-5和EU-1两种分子筛晶相, 且EU-1分子筛在ZSM-5分子筛表面缺陷处外延生长; 复合以后核壳分子筛为微孔-介孔多级孔道结构, 且其微孔孔径达到0.94 nm; 相比于单一分子筛, 核壳分子筛的强酸量相对提高, 酸性质有所改善。通过对柠檬酸加入量、晶化时间影响因素的分析, 得到合成核壳共生结构的最佳条件为: n(citrate)/n(Al₂O₃)=0.8~1.2, 晶化时间为72~96 h, 并推测核壳分子筛可能的生长过程。     

用不含有机模板剂的晶化液在多孔α-Al2O3管上合成ZSM-5沸石膜

采用不含有机模板剂的晶化液在平均孔径为2μm的多孔α-Al2O3管上合成了ZSM-5沸石膜.纳米ZSM-5沸石晶种的摩尔组成为9TPAOH25TEOS0.25 Al2O3480H2O.多孔α-Al2O3载体管外表面用这些粒度为100nm左右的晶种悬浮液浸涂、干燥后,依据纳米ZSM-5沸石晶种的DTA/TG进行煅烧,在不含有机模板剂的摩尔组成为67Na2OAl2O3240SiO26000H2O晶化液中合成了ZSM-5膜.XRD确定膜晶体为ZSM-5沸石,SEM表明沸石膜无缺陷,膜厚度约为8μm.制备的ZSM-5沸石膜H2的渗透率为1.50×10-6mol.m2·S-1.Pa-1,理想分离因数αH2/N2为3.85左右.     

两步晶化法制备MCM-48/ZSM-5复合分子筛

利用两步晶化法制备了高水热稳定性的MCM48/ZSM-5介微孔复合分子筛.通过SEM、TEM、XRD、IR和N₂吸附脱附进行表征,结果显示,该材料的结构不同于简单的机械混合,而是具有微孔孔壁和三维立方介孔孔道的复合材料,其孔道尺寸为2.6nm左右.该复合分子筛在沸水中处理6h后,介孔结构仍保留完好.通过考察晶化时间对复合分子筛的影响,证明了介孔和微孔的组装是一个竞争的过程,复合分子筛中介孔与微孔结构的比例随晶化时间的变化而变化,且具有介孔孔道和微孔孔壁的复合分子筛150℃的最优晶化时间为8h.     

Sn-ZSM-5沸石膜的合成及其在废水脱除乙酸中的应用

通过研究Sn-ZSM-5沸石分子筛的合成与表征,确定了在多孔陶瓷管上合成Sn-ZSM-5沸石膜的条件.首先利用水热合成法,从Si(OCH2CH3)4/SnCI4/TPABr/NaOH/H2O澄清体系中合成出Sn-ZSM-5沸石分子筛,从扫描电镜照片(SEM)看到沸石分子筛呈现近长方体形;X射线衍射(XRD)显示为MFI型结构,并测定其晶胞参数;红外光谱(IR)在约960cm-1左右显示特征峰,表明锡原子已经进入沸石骨架.在此基础上利用水热合成法在多孔陶瓷管上制备Sn-ZSM-5沸石膜,在90℃下对于质量分数5%的乙酸溶液,Sj/Sn原子比=25的沸石膜的选择系数为7.75,总通量达到0.490 kg/(m2·h).     

水蒸气诱导自组装制备介-微孔ZSM-5分子筛的研究

软模板剂方法可以合成介-微孔分子筛,但有些模板剂与硅铝酸盐之间弱的化学结合力导致晶化过程模板剂与合成体系的相分离,结果形成了无定型的介孔材料和微孔分子筛的混合物。采用新的技术路线:通过使用四丙基氢氧化铵(TPAOH)作模板剂,以三嵌段共聚物P123原位植入介孔结构,采用水蒸气诱导干凝胶自组装晶化的方法制备介-微孔ZSM-5分子筛。优点是:大大减少了模板剂的使用量,省去了产品与母液分离的繁琐步骤,无大量废液产生,对环境友好。采用X射线衍射 (XRD)、傅立叶变换红外光谱(FT-IR)、N₂吸附-脱附比表面分析(BET)、扫描电镜(SEM)、高倍透射电镜(TEM)系列表征方法对介-微孔ZSM-5分子筛进行表征,可知样品具有典型的ZSM-5分子筛的骨架结构和明显地介孔孔道。在800 ℃,100%水蒸气条件下经15 h水热老化后,分子筛的比表面积保留率73.44%,孔容保留率74.35%,表明分子筛的水热稳定性良好。     

The synthesis of nano-sized ZSM-5 zeolite by dry gel conversion method and investigating the effects of experimental parameters by Taguchi experimental design

In this study ZSM-5 Nano particles with high crystallinity were synthesized using a dry gel conversion technique. An L9 orthogonal array of the Taguchi method was applied to investigate the effect of synthesis parameters, such as crystallization time, gel drying temperature, molar composition of template (TPAOH) and water content in the crystallization stage on crystallinity and particle size of the ZSM-5 catalyst. The products were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Beside short crystallization time, the particle sizes were considerably smaller in comparison with those prepared using the hydrothermal method. The results showed that the particle size and crystallinity increased with increasing water content and crystallization time. The effects of gel drying temperature and molar composition of template were found to be more complex, however. Comparing to hydrothermal method, ZSM-5 samples synthesized with the dry gel conversion exhibited higher selectivity to gasoline than other hydrocarbons.     

Preparation of metal ion (Fe and Ni) doped TiO2 nanoparticles supported on ZSM-5 zeolite and investigation of its photocatalytic activity

Metal ion doped TiO₂ nanoparticles supported on ZSM-5 zeolite (M-TiO₂/ZSM-5 composites, M = Fe or Ni) were synthesized by hydrothermal method. The prepared composites were characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and UV–vis diffuse reflectance spectra (DRS). The photocatalytic activities of composites were evaluated by degradation of yellow GX aqueous solution under ambient condition. Fe-TiO₂/ZSM-5 composite showed to be more efficient catalyst for degradation of dye molecules as compared with Ni-TiO₂/ZSM-5 and TiO₂/ZSM-5. Its higher photocatalytic activity is attributed to the effective separation of charge carriers that will be discussed in this paper in detail.     

PBAT/ZSM-5分子筛共混薄膜的制备与性能

目的 以聚己二酸-对苯二甲酸丁二酯(PBAT)为基材,制备PBAT/ZSM-5分子筛共混薄膜,研究分子筛含量对薄膜性能的影响.方法 通过共混熔融挤出流延法制得含不同质量分数ZSM-5分子筛(0％,1％,3％,5％,7％)的PBAT薄膜,测定分析不同分子筛质量分数对薄膜的颜色、透明性、结构、气体阻隔性、力学性能等性能的影响.结果 随着分子筛质量分数的增加,透明性和断裂伸长率显著降低,抗拉强度先增加后降低,质量分数为1％分子筛的薄膜抗拉强度相对较大,较纯PBAT薄膜增加了12.34％;薄膜氧气透过性能整体上呈上升趋势,二氧化碳透过性和CO2/O2透过比均逐渐增加,水蒸气透过性显著降低,与纯PBAT薄膜相比,质量分数为7％分子筛PBAT薄膜的氧气和二氧化碳透过系数分别增加了18.48％,33.51％,水蒸气透过系数下降了43.28％,CO2/O2透过比由原来的8.84增加到9.96;薄膜表面和横截断面均变得粗糙,局部区域有团聚现象,且随分子筛含量的增加而变得明显.结论 ZSM-5分子筛的少量加入,可以影响PBAT薄膜力学性能,降低其水蒸气透过性,调节薄膜的气体选择透过性,为其应用于生鲜果蔬包装提供基础.