Too hot to carry on? Disinclination to persist at a task in a warm office environment

We investigated the effect of an elevated ambient temperature on performance in a persistence task. The task involved the coding of incorrect symbols and participants were free to decide how long to spend performing this task. Applying a between-subject design, we tested 125 students in an office-like environment in one of the three temperature conditions. The comfort condition (Predicted Mean Vote [PMV] = 0.01) featured an average air temperature of 24 °C. The elevated ambient temperature condition was 28 °C (PMV = 1.17). Condition three employed an airstream of approximately 0.8 m/s, intended to compensate for performance decrements at the elevated air temperature (28 °C, PMV = 0.13), according to Fanger’s thermal comfort equation. Participants in the warm condition were significantly less persistent compared with participants in the control and compensation conditions. As predicted by the thermal comfort equation, the airstream seemed to compensate for the higher temperature. Participants’ persistence in the compensation and comfort conditions did not differ.

Practitioner Summary: A laboratory experiment involving a simulated office environment and three ambient temperature conditions (24 °C, 28 °C and 28 °C plus airstream) showed that persistence at a task is significantly impaired at 28 °C. An airstream of 0.8 m/s at 28 °C compensated for the disinclination to persist with the task.     

Thermal and cardiovascular strain imposed by motorcycle protective clothing under Australian summer conditions

Motorcycle protective clothing can be uncomfortably hot during summer, and this experiment was designed to evaluate the physiological significance of that burden. Twelve males participated in four, 90-min trials (cycling 30 W) across three environments (25, 30, 35 °C [all 40% relative humidity]). Clothing was modified between full and minimal injury protection. Both ensembles were tested at 25 °C, with only the more protective ensemble investigated at 30 and 35 °C. At 35 °C, auditory canal temperature rose at 0.02 °C min^?1 (SD 0.005), deviating from all other trials (p < 0.05). The thresholds for moderate (>38.5 °C) and profound hyperthermia (>40.0 °C) were predicted to occur within 105 min (SD 20.6) and 180 min (SD 33.0), respectively. Profound hyperthermia might eventuate in ~10 h at 30 °C, but should not occur at 25 °C. These outcomes demonstrate a need to enhance the heat dissipation capabilities of motorcycle clothing designed for summer use in hot climates, but without compromising impact protection.

Practitioner’s Summary:

Motorcycle protective clothing can be uncomfortably hot during summer. This experiment was designed to evaluate the physiological significance of this burden across climatic states. In the heat, moderate (>38.5 °C) and profound hyperthermia (>40.0 °C) were predicted to occur within 105 and 180 min, respectively.     

Thermal response to firefighting activities in residential structure fires: impact of job assignment and suppression tactic

Firefighters’ thermal burden is generally attributed to high heat loads from the fire and metabolic heat generation, which may vary between job assignments and suppression tactic employed. Utilising a full-sized residential structure, firefighters were deployed in six job assignments utilising two attack tactics (1. Water applied from the interior, or 2. Exterior water application before transitioning to the interior). Environmental temperatures decreased after water application, but more rapidly with transitional attack. Local ambient temperatures for inside operation firefighters were higher than other positions (average ~10–30 °C). Rapid elevations in skin temperature were found for all job assignments other than outside command. Neck skin temperatures for inside attack firefighters were ~0.5 °C lower when the transitional tactic was employed. Significantly higher core temperatures were measured for the outside ventilation and overhaul positions than the inside positions (~0.6–0.9 °C). Firefighters working at all fireground positions must be monitored and relieved based on intensity and duration.

Practitioner Summary: Testing was done to characterise the thermal burden experienced by firefighters in different job assignments who responded to controlled residential fires (with typical furnishings) using two tactics. Ambient, skin and core temperatures varied based on job assignment and tactic employed, with rapid elevations in core temperature in many roles.     

A shirt containing multistage phase change material and active cooling components was associated with increased exercise capacity in a hot,humid environment

Recent advances in clothing design include the incorporation of phase change materials (PCM) and other active cooling components (ACC) to provide better body heat dissipation. The purpose of this study was to determine the effect of wearing a shirt containing multistage PCM/ACC on exercise capacity at low (5.0), moderate–high (7.5) and extreme (9.0) levels of the physiological strain index (PSI). Fourteen individuals tested two shirts (control vs. cooling) during 45-min of interval running in a hot, humid (35 ± 1 °C; 55 ± 6% RH) environment. The cooling shirt resulted in an 8% improvement in exercise capacity at a PSI of 7.5 (p < 0.05). The observed increase in exercise capacity would likely translate to a significant improvement in exercise performance. More research is needed to determine a best practice approach for the use of cooling clothing as a counter to exercise-induced heat exposure.

Practitioner Summary: In this report, we demonstrate that when forced to exercise in a hot, humid environment, an individual’s exercise capacity may increase by as much as 8% when wearing a shirt composed of multistage phase change material and active cooling components.     

Gender difference in mobile phone use and the impact of digital device exposure on neck posture

This cross-sectional study aimed to identify gender differences in the cervical postures when young adults were using mobile phones, as well as the correlations between the postures and the digital devices use (computer and mobile phone). Questionnaires regarding the habits of computer and mobile phone use were administrated to 429 subjects aged from 17 to 33 years old (19.75 ± 2.58 years old). Subjects were instructed to stand habitually and use a mobile phone as in daily life; the sagittal head and cervical postures were measured by head flexion, neck flexion angle and gaze angle. Male participants had a significantly larger head flexion angle (96.41° ± 12.23° vs. 93.57° ± 12.62°, p = 0.018) and neck flexion angle (51.92° ± 9.55° vs. 47.09° ± 9.45°, p < 0.001) than females. There were significant differences in head (F = 3.62, p = 0.014) and neck flexion (F = 3.99, p = 0.009) between different amounts of computer use.

Practitioner Summary: We investigated possible gender differences in head and neck postures of young adults using mobile phones, as well as the potential correlations between these postures and digital device use. We found that males displayed larger head and neck flexion angles than females, which were associated with the amount of computer use.     

Can an off-the-rack orthotic stiletto alter pressure and comfort scores in the forefoot,arch and heel?

The study sought to investigate whether an orthotic stiletto could modulate the pressure and comfort under the forefoot, arch and heel that stiletto wearers experience. Twenty-two women participated. We measured the peak pressure and pressure-time integral for orthotic stilettos with built-in metatarsal pad, heel cup and arch support; standard stilettos without inlays; and trainers. Comfort was recorded during 3 × 3 working days. The orthotic stiletto exhibited lower metatarsal head1 (MTH) and MTH2+3 and heel pressures than the standard stiletto (p < .01), and a long second metatarsal increased MTH2+3 pressure (p < .01). The comfort in the forefoot and heel was higher in the orthotic stiletto than in the standard one (p < .01), and comfort in the forefoot was correlated to the pressure-time integral of MTH2+3 (p = .03) and not peak pressure. Off-the-rack orthotic stilettos can notably reduce plantar pressures and improve forefoot and heel comfort during everyday use.

Practitioner Summary: Off-the-rack orthotic stilettos with built-in metatarsal pad, arch support and heel caps can lower the pressure under the heel and forefoot in comparison with a standard stiletto and can improve comfort during everyday use. Having a long second metatarsal is a risk factor for increased forefoot pressure.     

The hybrid personal cooling system (PCS) could effectively reduce the heat strain while exercising in a hot and moderate humid environment

This study aimed to examine the effectiveness of a hybrid personal cooling system (PCS) in mitigating body heat stain while exercising in a hot environment. Eight subjects underwent two trials: PCS and CON (i.e. no cooling). All trials were conducted at an air temperature of 36 ± 0.5 °C and RH = 59 ± 5%. The key findings demonstrated that the PCS could significantly reduce the core temperature, mean skin temperature, heart rate and physiological strain index during both exercise and recovery periods (p < 0.05). Subjective perceptions were also significantly alleviated in PCS at the end of the exercise and during the recovery (p < 0.05). Besides, the PCS could also bring remarkable benefits in lowering local skin temperatures and in improving perceptual sensations in both upper and lower body during both exercise and recovery periods (p < 0.05). It was thus concluded that the hybrid PCS is effective in mitigating body heat strain while exercising in a hot environment.

Practitioner Summary: In hot and humid environments, body heat dissipation through sweating is greatly restricted. Our newly developed hybrid PCS could effectively alleviate heat strain while exercising in hot environments. The findings contribute to the body of knowledge in improving the health and well-being of sportsmen while exercising in hot environments.     

Skin sites to predict deep-body temperature while wearing firefighters’ personal protective equipment during periodical changes in air temperature

The aim of this study was to investigate stable and valid measurement sites of skin temperatures as a non-invasive variable to predict deep-body temperature while wearing firefighters’ personal protective equipment (PPE) during air temperature changes. Eight male firefighters participated in an experiment which consisted of 60-min exercise and 10-min recovery while wearing PPE without self-contained breathing apparatus (7.75 kg in total PPE mass). Air temperature was periodically fluctuated from 29.5 to 35.5 °C with an amplitude of 6 °C. Rectal temperature was chosen as a deep-body temperature, and 12 skin temperatures were recorded. The results showed that the forehead and chest were identified as the most valid sites to predict rectal temperature (R² = 0.826 and 0.824, respectively) in an environment with periodically fluctuated air temperatures. This study suggests that particular skin temperatures are valid as a non-invasive variable when predicting rectal temperature of an individual wearing PPE in changing ambient temperatures.

Practitioner Summary: This study should offer assistance for developing a more reliable indirect indicating system of individual heat strain for firefighters in real time, which can be used practically as a precaution of firefighters’ heat-related illness and utilised along with physiological monitoring.     

Performance enhancement of hybrid personal cooling clothing in a hot environment: PCM cooling energy management with additional insulation

A novel design of personal cooling clothing incorporating additional insulation sandwiched between phase change materials (PCMs) and clothing outer layer is proposed. Performance of four personal cooling systems including clothing with only PCMs, clothing with PCMs and insulation (PCM?+?INS), clothing with PCMs and ventilation fans (HYB), and clothing with PCMs, ventilation fans and insulation (HYB?+?INS) was investigated. Effect of additional insulation on clothing cooling performance in terms of human physiological and perceptual responses was also examined. Human trials were carried out in a hot environment (i.e. 36?°C, RH = 59%). Results showed that significantly lower mean skin/torso temperatures were registered in HYB?+?INS as compared to HYB. In contrast, no significant effect of the use of insulation on both skin and body temperatures between PCM and PCM?+?INS was observed. Also, no significant difference in thermal sensations, thermal comfort, and skin wetness sensation was registered between cooling systems with and without additional insulation.

Practitioner Summary: Hybrid personal cooling clothing has shown the ability to provide a relatively cool microclimate around the wearer’ body while working in hot environments. The present work addresses the importance of cooling energy saving for PCMs in a hot environment. This work contributes to optimising cooling performance of hybrid personal cooling systems.     

Integrating a hip belt with body armour reduces the magnitude and changes the location of shoulder pressure and perceived discomfort in soldiers*

Soldiers carry heavy loads that may cause general discomfort, shoulder pain and injury. This study assessed if new body armour designs that incorporated a hip belt reduced shoulder pressures and improved comfort. Twenty-one Australian soldiers completed treadmill walking trials wearing six different body armours with two different loads (15 and 30 kg). Contact pressures applied to the shoulders were measured using pressure pads, and qualitative assessment of comfort and usability were acquired from questionnaires administered after walking trials. Walking with hip belt compared to no hip belt armour resulted in decreased mean and maximum shoulder pressures (p < 0.005), and 30% fewer participants experiencing shoulder discomfort (p < 0.005) in best designs, although hip discomfort did increase. Laterally concentrated shoulder pressures were associated with 1.34-times greater likelihood of discomfort (p = 0.026). Results indicate body armour and backpack designs should integrate a hip belt and distribute load closer to shoulder midline to reduce load carriage discomfort and, potentially, injury risk.

Practitioner Summary: Soldiers carry heavy loads that increase their risk of discomfort and injury. New body armour designs are thought to ease this burden by transferring the load to the hips. This study demonstrated that designs incorporating a hip belt reduced shoulder pressure and shoulder discomfort compared to the current armour design.     

A comfort assessment of existing cervical orthoses

Purpose: Identify location and intensity of discomfort experienced by healthy participants wearing cervical orthoses.

Method: Convenience sample of 34 healthy participants wore Stro II, Philadelphia, Headmaster, and AspenVista^® cervical orthoses for four-hour periods. Participants reported discomfort level (scale 0–6) and location.

Results: Participants reported mean discomfort for all orthoses over the four-hour test between ‘a little discomfort’ and ‘very uncomfortable’ (mean discomfort score = 1.64, SD = 1.50). Seven participants prematurely stopped tests due to pain and six reported maximum discomfort scores. Significant linear increase in discomfort with duration of wear was found for all orthoses. Significantly less discomfort was reported with Stro II than Headmaster and Philadelphia. Age correlated with greater perceived discomfort. Orthoses differed in the location discomfort was experienced.

Conclusion: Existing cervical orthoses cause discomfort influenced by design and duration of wear with orthoses’ design the more significant factor. This work informed the design of a new orthosis and future orthoses developments.

Practitioner Summary: The purpose of this study was to gain greater knowledge about the discomfort caused by wearing of existing neck orthoses in order to inform the design and development of a new neck orthosis. This study gathers empirical data from a surrogate population and concludes that orthosis design is more influential than the duration of wear.     

Home is where the head is: a distributed cognition account of personal health information management in the home among those with chronic illness

Managing chronic illness requires personal health information management (PHIM) to be performed by lay individuals. Paramount to understanding the PHIM process is understanding the sociotechnical system in which it frequently occurs: the home environment. We combined distributed cognition theory and the patient work system model to investigate how characteristics of the home interact with the cognitive work of PHIM. We used a 3D virtual reality CAVE that enabled participants who had been diagnosed with diabetes (N = 20) to describe how they would perform PHIM in the home context. We found that PHIM is distinctly cognitive work, and rarely performed ‘in the head’. Rather, features of the physical environment, tasks, people, and tools and technologies present, continuously shape and are shaped by the PHIM process. We suggest that approaches in which the individual (sans context) is considered the relevant unit of analysis overlook the pivotal role of the environment in shaping PHIM.

Practitioner Summary:

We examined how Personal Health Information Management (PHIM) is performed in the homes of diabetic patients. We found that approaches to studying cognition that focus on the individual, to the exclusion of their context, overlook the pivotal role of environmental, social, and technological features in shaping PHIM.     

The development of anti-heat stress clothing for construction workers in hot and humid weather

The purpose of this study was to develop anti-heat stress clothing for construction workers in hot and humid weather. Following DeJonge’s functional clothing design process, the design situation was explored, including clothing fabric heat/moisture transporting properties and UV protection and the aspects of clothing ergonomic design (mobility, convenience, and safety). The problem structure was derived from the results of the surveys in three local construction sites, which agreed well with the task requirements and observations. Specifications were consequently described and 30 commercially available fabrics were identified and tested. Fabric testing data and design considerations were inputted in S-smart system to predict the thermal functional performance of the clothing. A new uniform prototype was developed and evaluated. The results of all measurements suggest that the new uniform which incorporated fabrics with superior heat/moisture transporting properties and loose-fitting design could reduce the workers’ heat stress and improve their comfort and work performance.

Practitioner Summary:

The construction workers’ uniform currently used in Hong Kong during summer was unsatisfactory. Following DeJonge’s functional clothing design process, an anti-heat stress uniform was developed by testing 30 fabrics and predicting clothing thermal functional performance using S-smart system. The new uniform could reduce the workers’ heat stress and improve their comfort and work performance.     

Straight ladder inclined angle in a field environment: the relationship among actual angle,method of set-up and knowledge

Ladder inclined angle is a critical factor that could lead to a slip at the base of portable straight ladders, a major cause of falls from heights. Despite several methods established to help workers achieve the recommended 75.5° angle for ladder set-up, it remains unclear if these methods are used in practice. This study explored ladder set-up behaviours in a field environment. Professional installers of a company in the cable and other pay TV industry were observed for ladder set-up at their worksites. The results showed that the actual angles of 265 ladder set-ups by 67 participants averaged 67.3° with a standard deviation of 3.22°. Although all the participants had training on recommended ladder set-up methods, only 3 out of 67 participants applied these methods in their daily work and even they failed to achieve the desired 75.5° angle. Therefore, ladder set-up remains problematic in real-world situations.

Practitioner Summary: Professional installers of a cable company were observed for portable straight ladder set-up at their worksites. The ladder inclined angle averaged 67.3° with a standard deviation of 3.22°, while the recommended angle is 75.5°. Only a few participants used the methods that they learned during training in their daily work.     

Are hybrid sit–stand postures a good compromise between sitting and standing?

Potential alternatives for conventional sitting and standing postures are hybrid sit-stand postures (i.e. perching). The purposes of this study were (i) to identify where lumbopelvic and pelvic angles deviate from sitting and standing and (ii) to use these breakpoints to define three distinct postural phases: sitting, perching, and standing, in order to examine differences in muscle activations and ground reaction forces between phases. Twenty-four participants completed 19 1-min static trials, from sitting (90°) to standing (180°), sequentially in 5°trunk–thigh angle increments. The perching phase was determined to be 145–175° for males and 160–175° for females. For both sexes, knee extensor activity was lower in standing compared to perching or sitting (p < .01). Anterior–posterior forces were the highest in perching (p < .001), requiring ～15% of body-weight. Chair designs aimed at reducing the lower limb demands within 115–170° trunk–thigh angle may improve the feasibility of sustaining the perched posture.

Practitioner summary: Individuals who develop low back pain in sitting or standing may benefit from hybrid sit-stand postures (perching), yet kinematic and kinetic changes associated with these postures have not been investigated. Perching can improve lumbar posture at a cost of increased lower limb demands, suggesting potential avenues for chair design improvement.

Abbreviations: A/P: anterior-posterior; M/L: medial-lateral; LBP: low back pain; EMG: electromyography; TES: thoracic erector spinae; LES: lumbar erector spinae; VMO: vastus medialis obliquus; MVC: maximum voluntary contraction; ASIS: anterior superior iliac spine; PSIS: posterior superior iliac spine; BW: body weight; RMSE: root mean square error; SD: standard deviation; ROM: range of motion     

Lift performance and lumbar loading in standing and seated lifts

This study investigated the effect of posture on lifting performance. Twenty-three male soldiers lifted a loaded box onto a platform in standing and seated postures to determine their maximum lift capacity and maximum acceptable lift. Lift performance, trunk kinematics, lumbar loads, anthropometric and strength data were recorded. There was a significant main effect for lift effort but not for posture or the interaction. Effect sizes showed that lumbar compression forces did not differ between postures at lift initiation (Standing 5566.2?±?627.8 N; Seated 5584.0?±?16.0) but were higher in the standing posture (4045.7?±?408.3 N) when compared with the seated posture (3655.8?±?225.7 N) at lift completion. Anterior shear forces were higher in the standing posture at both lift initiation (Standing 519.4?±?104.4 N; Seated 224.2?±?9.4 N) and completion (Standing 183.3?±?62.5 N; Seated 71.0?±?24.2 N) and may have been a result of increased trunk flexion and a larger horizontal distance of the mass from the L5-S1 joint.

Practitioner Summary: Differences between lift performance and lumbar forces in standing and seated lifts are unclear. Using a with-in subjects repeated measures design, we found no difference in lifted mass or lumbar compression force at lift initiation between standing and seated lifts.     

The three-dimensional shapes of underground coal miners’ feet do not match the internal dimensions of their work boots

Mining work boots provide an interface between the foot and the ground, protecting and supporting miners’ feet during lengthy coal mining shifts. Although underground coal miners report the fit of their work boots as reasonable to good, they frequently rate their boots as uncomfortable, suggesting that there is a mismatch between the shape of their feet and their boots. This study aimed to identify whether dimensions derived from the three-dimensional scans of 208 underground coal miners’ feet (age 38.3 ± 9.8 years) differed from the internal dimensions of their work boots. The results revealed underground coal miners wore boots that were substantially longer than their feet, possibly because boots available in their correct length were too narrow. It is recommended boot manufacturers reassess the algorithms used to create boot lasts, focusing on adjusting boot circumference at the instep and heel relative to increases in foot length.

Practitioner Summary: Fit and comfort ratings suggest a mismatch between the shape of underground coal miners’ feet and their boots exists. This study examined whether three-dimensional scans of 208 miners’ feet differed from their boot internal dimensions. Miners wore boots substantially longer than their feet, possibly due to inadequate width.     

Normative data on the one-handed static pull strength of a Chinese population and a comparison with American data

We assess the one-handed static pull strength of a Chinese population and compare it to that of an American sample. Fifty men and 50 women in five age groups were asked to exert their maximum one-handed pull strength in three pulling directions (across, front and side) and from four pulling heights (61 cm, 76 cm, waist height and above-shoulder height). The results showed that women had less pull strength than men under all of the conditions tested. The front and side pulling resulted in the greatest pull strength, with a decrease detected when the pulling height was increased. The American sample exhibited greater strength than the Chinese. Body mass and men’s handgrip force were also associated with the pull strength. These variables should be taken into account in the development of tasks related to one-handed pulling.

Practitioner summary:

In this paper, we report a laboratory-based experiment conducted to assess the one-handed static pull strength of a Chinese population and compare the results with those of an American population. The variables associated with pull strength included gender, pulling direction, pulling height, race, body mass and men’s handgrip force.     

Evaluation of eye,head and trunk coordination during target tracking tasks

This study tested the feasibility of a method to synchronise and to evaluate eye, head and trunk movement patterns during target tracking tasks performed by 10 subjects. A projected central target was randomly repositioned at 40° and 70° of rotation to the left and right. Subjects were instructed to change gaze as quickly as possible. Head and trunk motion was measured using a motion analysis system, and eye movement was measured using an eye-tracker; all data were synchronised. For healthy subjects, the eye moved faster than the head, there was no trunk movement and the head moved more than the eye to reach further displaced targets. The method tested was feasible, and it could be used to evaluate eye, head and trunk movement patterns of subjects with injuries such as whiplash and concussions.

Practitioner Summary: Studies of eye, head and trunk movements using synchronised methods are needed. We tested the feasibility of a method to synchronise and evaluate eye, head and trunk movement patterns. The method tested was feasible, and it could be used to evaluate movement patterns of subjects with injuries such as whiplash.