Modification of the alumina‐supported Mo‐based hydrodesulfurization catalysts by tungsten

The incorporation effect of tungsten as an activity‐promotional modifier into the Ni‐promoted Mo/γ‐Al₂O₃ catalyst was studied. Series of W‐incorporated catalysts with different content of tungsten were prepared by changing the impregnation order of nickel and tungsten onto a base Mo/γ‐Al₂O₃. Catalytic activities were measured from the atmospheric reactions of thiophene hydrodesulfurization (HDS) and ethylene hydrogenation (HYD). The HDS and HYD activities of the WMo/γ‐Al₂O₃ catalysts (WM series) initially increased and subsequently decreased with increasing content of tungsten as compared with those of their base Mo/γ‐Al₂O₃. The maximal activity promotion occurred at the W/(W + Mo) atomic ratio 0.025. For the Ni‐promoted Mo/γ‐Al₂O₃ catalysts, the effect of W incorporation was greatly dependent on the impregnation order of tungsten. The catalysts prepared by impregnating Ni onto the WMo/γ‐Al₂O₃ catalysts showed the same trend of activity promotion as for the WM series, while those by impregnating W onto a NiMo/γ‐Al₂O₃ catalyst resulted in lower activities than their base NiMo/γ‐Al₂O₃ catalyst. To characterize the catalysts, temperature‐programmed reduction and low‐temperature oxygen chemisorption were conducted. The effects of W incorporation on the NiMo‐based catalysts were discussed in reference to those on the CoMo‐based catalysts. This revised version was published online in July 2006 with corrections to the Cover Date.     

Steady State Isotopic Transient Kinetic Analysis of Flameless Methane Combustion over Pd/Al2O3 and Pt/Al2O3 Catalysts

The SSITKA measurements were performed in the steady state of complete methane oxidation on the Pd/Al₂O₃ and Pt/Al₂O₃ catalysts. It was found that the number of intermediates and their average life-time on the catalyst surface changes with the increase of reaction temperature. On the Pd/Al₂O₃ catalyst there is larger number of active centres than on Pt/Al₂O₃ catalyst which permits the course of methane oxidation at lower temperatures.     

High Efficiency of Noble Metal and Metal Oxide Catalyst Systems for the Selective Reduction of NO with Propene in Lean Exhaust Gas

An investigation was conducted of noble metal and metal oxide catalysts deposited on Al₂O₃. The noble metals Pt, Pd, Rh the metal oxides CuO, SnO₂, CoO, Ag₂O, In₂O₃, catalysts were examined. Also investigated were noble metal Pt, Pd, Rh-doped In₂O₃/Al₂O₃ catalysts prepared by single sol–gel method. Both were studied for their capability to reduce NO by propene under lean conditions. In order to improve the catalytic activity and the temperature window, the intermediate addition propene between a Pt/Al₂O₃ oxidation and metal oxide combined catalyst system was also studied. Pt/Al₂O₃ and In₂O₃/Al₂O₃ combined catalyst showed high NO reduction activity in a wider temperature window, and more than 60% NO conversion was observed in the temperature range of 300–550 °C.     

Nanodispersed Au/Al2O3 catalysts for low-temperature CO oxidation: Results of research activity at the Boreskov Institute of Catalysis

This paper presents some important results of the studies on preparation and catalytic properties of nanodispersed Au/Al₂O₃ catalysts for low-temperature CO oxidation, which are carried out at the Boreskov Institute of Catalysis (BIC) starting from 2001. The catalysts with a gold loading of 1–2 wt.% were prepared via deposition of Au complexes onto different aluminas by means of various techniques (“deposition-precipitation” (DP), incipient wetness, “chemical liquid-phase grafting” (CLPG), chemical vapor deposition (CVD)). These catalysts have been characterized comparatively by a number of physical methods (XRD, TEM, diffuse reflectance UV/vis and XPS) and catalytically tested for combustion of CO impurity (1%) in wet air stream at near-ambient temperature. Using the hydroxide or chloride gold complexes capable of chemical interaction with the surface groups of alumina as the catalyst precursors (DP and incipient wetness techniques, respectively) produces the catalysts that contain metallic Au particles mainly of 2–4 nm in diameter, uniformly distributed between the external and internal surfaces of the support granules together with the surface “ionic” Au oxide species. Application of organogold precursors gives the supported Au catalysts of egg shell type which are either close by mean Au particle size to what we obtain by DP and incipient wetness techniques (CVD of (CH₃)₂Au(acac) vapor on highly dehydrated Al₂O₃ in a rotating reactor under static conditions) or contain Au crystallites of no less than 7 nm in size (CLPG method). Regardless of deposition technique, only the Cl-free Au/Al₂O₃ catalysts containing the small Au particles (d_i ≤ 5 nm) reveal the high catalytic activity toward CO oxidation under near-ambient conditions, the catalyst stability being provided by adding the water vapor into the reaction feed. The results of testing of the nanodispersed Au/Al₂O₃ catalysts under conditions which simulate in part removal of CO from ambient air or diesel exhaust are discussed in comparison with the data obtained for the commercial Pd and Pt catalysts under the same conditions.     

Deactivation and coke formation on palladium and platinum catalysts in vegetable oil hydrogenation

Deactivation of palladium and platinum catalysts due to coke formation was studied during hydrogenation of methyl esters of sunflower oil. The supported metal catalysts were prepared by impregnating γ-alumina with either palladium or platinum salts, and by impregnating α-alumina with palladium salt. The catalysts were reused for several batch experiments. The Pd/γ-Al₂O₃ catalyst lost more than 50% of its initial activity after four batch experiments, while the other catalysts did not deactivate. Samples of used catalysts were cleaned from remaining oil by repeated extractions with methanol, and the amount of coke formed on the catalysts was studied by temperature-programmed oxidation. The deactivation of the catalyst is a function of both the metal and the support. The amount of coke increased on the Pd/γ-Al₂O₃ catalyst with repeated use, but the amount of coke remained approximately constant for the Pt/γ-Al₂O₃ catalyst. Virtually no coke was detected on the Pd/α-Al₂O₃ catalyst. The formation of coke on Pd/α-Al₂O₃ may be slower than on the Pd/γ-Al₂O₃ owing to the carrier’s smaller surface area and less acidic character. The absence of deactivation for the Pt/γ-Al₂O₃ catalyst may be explained by slower formation of coke precursors on platinum compared to palladium.     

Combustion of Methane at Low Temperature over Pd and Pt Catalysts Supported on Al2O3, SnO2 and Al2O3-Grafted SnO2

Pd and Pt catalysts supported on alumina, tin(IV) oxide and tin(IV) oxide grafted on alumina were prepared, characterised and tested with respect to the low-temperature combustion of methane after reduction in H₂ and ageing under reactants at 600°C. In the case of Pd, the use of SnO₂ or SnO₂-based supports led to catalysts slightly less active than Pd/Al₂O₃. In contrast, SnO₂ was found to strongly promote the oxidation of methane over Pt catalysts with respect to Pt/Al₂O₃, even after ageing under reactants. When Pt was supported on SnO₂ grafted on Al₂O₃, the activity was found at most similar to or, after ageing, lower than Pt/Al₂O₃. This negative effect was discussed, being partly related to the sintering of SnO₂ under reactants observed by FTIR and XRD.     

Hydrogen production by steam reforming of LNG over Ni/Al2O3-ZrO2 catalysts: Effect of ZrO2 and preparation method of Al2O3-ZrO2

An Al₂O₃-ZrO₂ support was prepared by grafting a zirconium precursor onto the surface of commercial γ-Al₂O₃. A physical mixture of Al₂O₃-ZrO₂ was also prepared for the purpose of comparison. Ni/Al₂O₃-ZrO₂ catalysts were then prepared by an impregnation method, and were applied to the hydrogen production by steam reforming of liquefied natural gas (LNG). The effect ZrO₂ and preparation method of Al₂O₃-ZrO₂ on the performance of supported nickel catalysts in the steam reforming of LNG was investigated. The Al₂O₃-ZrO₂ prepared by a grafting method was more efficient as a support for nickel catalyst than the physical mixture of Al₂O₃-ZrO₂ in the hydrogen production by steam reforming of LNG. The well-developed tetragonal phase of ZrO₂ and the high dispersion of ZrO₂ on the surface of γ-Al₂O₃ were responsible for the enhanced catalytic performance of Ni/Al₂O₃-ZrO₂ prepared by way of a grafting method.     

FTIR study of CO adsorption on coked Pt–Sn/Al2O3 catalysts

Infrared spectra of adsorbed CO have been used as a probe to monitor changes in Pt site character induced by the coking of Pt/Al₂O₃ and Pt–Sn/Al₂O₃ catalysts by heat treatment in heptane/hydrogen. Four distinguishable types of Pt site for the linear adsorption of CO on Pt/Al₂O₃ were poisoned to different extents showing the heterogeneity of the exposed Pt atoms. The lowest coordination Pt atoms (ν(CO) < 2030 cm⁻¹) were unpoisoned whereas the highest coordination sites in large ensembles of Pt atoms (2080 cm⁻¹) were highly poisoned, as were sites of intermediate coordination (2030–2060 cm⁻¹). Sites in smaller two‐dimensional ensembles of Pt atoms (2060–2065 cm⁻¹) were partially poisoned, as were sites for the adsorption of CO in a bridging configuration. The addition of Sn blocked the lowest coordination sites and destroyed large ensembles of Pt by a geometric dilution effect. The poisoning of other sites by coke was impeded by Sn, this effect being magnified for Cl‐containing catalyst. Oxidation or oxychlorination of coked catalyst at 823 K followed by reduction completely removed coke from the catalyst surfaces. This revised version was published online in July 2006 with corrections to the Cover Date.     

Catalytic Activities of Al2O3-promoted NiSO4/TiO2 for Acid Catalysis

A series of catalysts, NiSO₄/Al₂O₃–TiO₂, for acid catalysis was prepared by the impregnation method, where support, Al₂O₃–TiO₂ was prepared by the coprecipitation method using a mixed aqueous solution of titanium tetrachloride and aluminum nitrate solution followed by adding an aqueous ammonia solution. The addition of nickel sulfate (or Al₂O₃) to TiO₂ shifted the phase transition of TiO₂ from amorphous to anatase to higher temperature because of the interaction between nickel sulfate (or Al₂O₃) and TiO₂. 15-NiSO₄/5-Al₂O₃–TiO₂ containing 15 wt% NiSO₄ and 5 mol% Al₂O₃, and calcined at 400°C exhibited maximum catalytic activities for both reactions, 2-propanol dehydration and cumene dealkylation. The catalytic activities for both reactions were correlated with the acidity of catalysts measured by the ammonia chemisorption method. The charge transfer from Ti atoms to the neighboring Al atoms strengthens the Al–O bond between Al and the surface sulfate species. The addition of Al₂O₃ up to 5 mol% enhanced the acidity, thermal property, and catalytic activities of NiSO₄/Al₂O₃–TiO₂ gradually due to the interaction between Al₂O₃ and TiO₂ and consequent formation of Al–O–Ti bond.     

Characterization of hydrodesulfurization catalyst prepared by impregnating cobalt nitrate solution onto the sulfided MoO3/Al2O3 catalyst

CoMo/Al₂O₃ catalysts were prepared by impregnating Cobalt nitrate solution into oxidic or sulfided Mo/Al₂O₃. The properties of CoMo/Al₂O₃ catalysts were characterized by XRD, TPS, oxygen chemisorption and ESR. Catalytic activity of CoMo/Al₂O₃ catalyst was evaluated by thiophene HDS as a probe reaction. When CoMo/Al₂O₃ catalyst was prepared by impregnating Cobalt nitrate solution into sulfided Mo/Al₂O₃, the interaction between Mo and alumina became weaker and the formation of synergic phase was facilitated. These structural changes may explain higher HDS activity of CoMo/Al₂O₃ catalyst prepared by impregnating Cobalt nitrate solution into sulfided Mo/Al₂O₃.     

Role of La2O3 in Pd-Supported Catalysts for Methanol Decomposition

Systems of Pd supported on various La₂O₃-modified -Al₂O₃ and CeO₂–Al₂O₃ catalysts were tested for catalytic methanol decomposition and characterized by means of XRD, BET, TPR, H₂-chemisorption and CO–FTIR. The addition of lanthanum significantly improved the selectivity of CO and H₂ for all the catalysts but showed a different influence on the catalytic activity in two systems. Methanol conversion decreased on La₂O₃-modified Pd/-Al₂O₃ catalysts, in line with the reduction of Pd dispersion, while the addition of La₂O₃ improved the dispersion of Pd and reinforced Pd–CeO₂ interaction for La₂O₃-modified Pd/CeO₂–Al₂O₃ catalysts, which resulted in a high production rate of CO and H₂. Thus, a synergistic effect between CeO₂ and La₂O₃ was observed on -Al₂O₃-supported Pd catalyst for methanol decomposition.     

Production of hydrogen by steam reforming of bio-oil over Ni/Al2O3 catalysts: Effect of addition of promoter and preparation procedure

Catalytic steam reforming of bio-oil was investigated in a fixed bed tubular reactor for production of hydrogen. Two series of nickel/alumina (Ni/Al₂O₃) supported catalysts promoted with ruthenium (Ru) and magnesium (Mg) were prepared. Each catalyst of the first series (Ru–Ni/Al₂O₃) was prepared by co-impregnation of nickel and ruthenium on alumina. They were examined to investigate the effect of adding ruthenium on the performance of the catalysts for hydrogen production. The effect of the temperature, the most effective parameter in the steam reforming of bio-oil, on the activity of the catalysts was also investigated. Each catalyst of the second series (Ni–MgO/Al₂O₃) was prepared by consecutive impregnation using various preparation procedures. They were tested to determine the effect of adding magnesium as well as the effect of the preparation procedure on the outlet gas concentrations. It was shown that in both series, the catalysts were more efficient in hydrogen production as well as carbon conversion than Ni/Al₂O₃ catalysts. The highest hydrogen yield was 85% which was achieved over Ru–Ni/Al₂O₃ at 950 °C. It was also found that the effect of adding a small amount of ruthenium was superior to that of nickel on the yield of hydrogen when the nickel content was equal to or greater than 10.7%.     

Formation of carbon nanotubes from the carbon monoxide disproportionation reaction over Co/Al2O3 and Co/SiO2 catalysts

The ammonia method has been successfully used for preparing thermostable and well dispersed alumina‐supported catalysts with a surface average size of cobalt particle D _{s= 5.7} nm. The disproportionation reaction of CO over this Co/Al₂O₃ catalyst and a similar Co/SiO₂ catalyst leads to the formation of carbon nanotubes demonstrating the same morphology. The amount of nanotubes over Co/Al₂O₃, however, is much larger than that obtained over Co/SiO₂, because of a faster ageing in the latter solid. Similar support effects have already been reported for other catalytic reactions involving carbon oxides. This revised version was published online in July 2006 with corrections to the Cover Date.     

Size Dependent Study of MeOH Decomposition Over Size-selected Pt Nanoparticles Synthesized via Micelle Encapsulation

We communicate experimental results for the oxidation of methane by oxygen over alumina supported Pd and Pt monolith catalysts under transient conditions. Temperature programmed reaction (TPReaction) and reactant pulse-response (PR) experiments have been performed, using a continuous gas-flow reactor equipped with a downstream mass spectrometer for gas phase analysis. Special attention was paid to the influence of gas composition changes, i.e., O₂ and H₂ pulsing, respectively, on the methane conversion. For Pt/Al₂O₃ oxygen pulsing can significantly increase the methane conversion which can be even further improved by pulsing hydrogen instead. Such transient effects are not observed for the Pd/Al₂O₃ catalyst for which instead constantly lean conditions is beneficial. Our results suggest that under lean conditions Pd and Pt crystallites may undergo bulk- and partial (surface oxide formation) oxidation, respectively, which for Pd results in more active surfaces, while for Pt the activity is reduced. The latter seems to connect to a lowering of the ability to dissociate methane.     

Promotional effect of Ca on the Pd/Ce–Zr/Al2O3 catalyst for low-temperature catalytic combustion of methane

Promotional effect of Ca on the catalytic property of Pd/Ce–Zr/Al₂O₃ catalyst towards methane combustion is examined. The surface properties and the oxidation/reduction behavior of these catalysts are investigated by BET, TEM, XPS, TPR, TPO and TPSR techniques. Activity tests in methane combustion show that addition of Ca to Pd/Ce–Zr/Al₂O₃ can promote remarkably its low-temperature activity. The thermal stability of the Pd/Ce–Zr/Al₂O₃ catalyst to the exposure at high temperature is also enhanced by Ca loading. XPS and TEM results show that the addition of Ca to Pd/Ce–Zr/Al₂O₃ catalyst generates well-dispersed PdO particles on support. H₂–TPR, O₂–TPO and CH₄/O₂–TPSR experiments show that the addition of Ca improves the reduction/reoxidation properties and thermal stability of the active PdO species, which increases the catalytic activity and thermal stability of the Pd/Ce–Zr/Al₂O₃ catalyst.     

Efficient production of hydrogen and multi-walled carbon nanotubes from ethanol over Fe/Al2O3 catalysts

Fe/Al₂O₃ catalysts with different Fe loadings (10-90 mol%) were prepared by hydrothermal method. Ethanol decomposition was studied over these Fe/Al₂O₃ catalysts at temperatures between 500 and 800 °C to produce hydrogen and multi-walled carbon nanotubes (MWCNTs) at the same time. The results showed that the catalytic activity and stability of Fe/Al₂O₃ depended strongly on the Fe loading and reaction temperature. The Fe(30 mol%)/Al₂O₃ and Fe(40 mol%)/Al₂O₃ were both the effective catalyst for ethanol decomposition into hydrogen and MWCNTs at 600 °C. Several reaction pathways were proposed to explain ethanol decomposition to produce hydrogen and carbon (including nanotube) at the same time.     

Effects of MgO promoter on properties of Ni/Al2O3 catalysts for partial oxidation of methane to syngas

The effects of MgO promoter on the physicochemical properties and catalytic performance of Ni/Al₂O₃ catalysts for the partial oxidation of methane to syngas were studied by means of BET, XRD, H₂-TPR, TEM and performance evaluation. It was found that the MgO promoter benefited from the uniformity of nickel species in the catalysts, inhibited the formation of NiAl₂O₄ spinel and improved the interaction between nickel species and support. These results were related to the formation of NiO-MgO solid solution and MgAl₂O₄ spinel. Moreover, for the catalysts with a proper amount of MgO promoter, the nickel dispersiveness was enhanced, therefore making their catalytic performance in methane partial oxidation improved. However, the excessive MgO promoter exerted a negative effect on the catalytic performance. Meanwhile, the basicity of MgO promoted the reversed water-gas shift reaction, which led to an increase in CO selectivity and a decrease in H₂ selectivity. The suitable content of MgO promoter in Ni/Al₂O₃ catalyst was ∼7 wt-%. Translated from Journal of Fuel Chemistry and Technology, 2006, 34(4): 450–455 [译自: 燃料化学学报]     

Influence of homogeneous decane oxidation on the catalytic performance of lean NO x catalysts

Extensive homogeneous gasphase reactions were observed when decane was used as the hydrocarbon reductant for the selective reduction of NO _x . The catalytic performance of a SnO₂/CoO _x /Al₂O₃ catalyst was found to be strongly dependent on the extent of the homogeneous reaction in the precatalytic volume. The effect of the homogeneous reaction on the catalytic performance also depended on whether SO₂ was present in the feed. By filling the precatalytic volume with 25–35 mesh irregularly shaped quartz chips, gasphase reaction was suppressed significantly. This methodology was used to evaluate the inherent catalytic performance of SnO₂/CoO _x /Al₂O₃ and SnO₂/Al₂O₃ catalysts with decane as a reductant. It was found that in the absence of SO₂, SnO₂/Al₂O₃ was a better catalyst than SnO₂/CoO _x /Al₂O₃, but in the presence of 30 ppm of SO₂ the latter was a far better catalyst.     

Role of ZnO in Cu/ZnO/Al2O3 catalyst for hydrogenolysis of butyl butyrate

For hydrogenolysis of butyl butyrate (BB), a series of Cu/ZnO/Al₂O₃ catalysts with different metal compositions were prepared, and characterized by N₂O chemisorption for measuring Cu surface area and by chromatographic experiment for determining the heat of BB adsorption. As a result, the presence of ZnO in Cu-based catalysts was found to enhance the catalytic activity of Cu due to dual function of ZnO. The Cu surface area was linearly correlated with the butanol productivity, demonstrating that ZnO exerts the structural function in Cu/ZnO/Al₂O₃ catalysts. Additionally, the role of ZnO as a chemical contributor was revealed such that its presence leads to lower activation energy of the surface reaction, thus resulting in higher Cu catalytic activity obtained at a low temperature such as 200 °C. Consequently, optimizing the Cu/Zn ratio in Cu/ZnO/Al₂O₃ catalyst is required to tune its structural and chemical characteristics of Cu metals, and thus to obtain a higher activity on the hydrogenolysis reaction.     

The Effects of Al2O3 Addition and WO3 Modification on Catalytic Activities of NiO/TiO2 for Acid Catalysis

NiO/Al₂O₃–TiO₂/WO₃ catalysts for acid catalysis were prepared by the addition of Al₂O₃ and the modification with WO₃. The strong acid sites were formed through the bonding between dispersed WO₃ and TiO₂. The larger the dispersed WO₃ amount, the higher both the acidity and catalytic activity. The addition of Al₂O₃ up to 5 mol% enhanced acidity and catalytic activity of NiO/Al₂O₃–TiO₂/WO₃ gradually due to the interaction between Al₂O₃ and TiO₂ and consequent formation of Al–O–Ti bond. The presence of NiO may attract reactants and enhance the local concentration of reactants near acid sites and consequently increase catalytic activity.