Time‐of‐Flight Studies of Electron‐Collection Kinetics in Polymer:Fullerene Bulk‐Heterojunction Solar Cells

The charge‐collection dynamics in poly(3‐hexylthiophene:[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (P3HT:PCBM) bulk heterojunctions are studied in thick (>1 μm) devices using time‐of‐flight measurements and external quantum‐efficiency measurements. The devices show Schottky‐diode behavior with a large field‐free region in the device. Consequently, electron transport occurs by diffusion in the bulk of the active layer. At high applied biases where the depletion region spans the entire active layer, normal time‐of‐flight transients are observed from which the electron mobility can be determined. Here, the electron mobility follows Poole–Frenkel behavior as a function of field. At lower applied biases, where the depletion region only spans a small portion of the active layer, due to a high density of dark holes, the recombination kinetics follow a first‐order rate law with a rate constant about two orders of magnitude lower than that predicted by Langevin recombination.     

Nanoscale Morphology of Conjugated Polymer/Fullerene‐Based Bulk‐ Heterojunction Solar Cells

The relation between the nanoscale morphology and associated device properties in conjugated polymer/fullerene bulk‐heterojunction “plastic solar cells” is investigated. We perform complementary measurements on solid‐state blends of poly[2‐methoxy‐5‐(3,7‐dimethyloctyloxy)]‐1,4‐phenylenevinylene (MDMO‐PPV) and the soluble fullerene C₆₀ derivative 1‐(3‐methoxycarbonyl) propyl‐1‐phenyl [6,6]C₆₁ (PCBM), spin‐cast from either toluene or chlorobenzene solutions. The characterization of the nanomorphology is carried out via scanning electron microscopy (SEM) and atomic force microscopy (AFM), while solar‐cell devices were characterized by means of current–voltage (I–V) and spectral photocurrent measurements. In addition, the morphology is manipulated via annealing, to increase the extent of phase separation in the thin‐film blends and to identify the distribution of materials. Photoluminescence measurements confirm the demixing of the materials under thermal treatment. Furthermore the photoluminescence of PCBM clusters with sizes of up to a few hundred nanometers indicates a photocurrent loss in films of the coarser phase‐separated blends cast from toluene. For toluene‐cast films the scale of phase separation depends strongly on the ratio of MDMO‐PPV to PCBM, as well as on the total concentration of the casting solution. Finally we observe small beads of 20–30 nm diameter, attributed to MDMO‐PPV, in blend films cast from both toluene and chlorobenzene.     

Quantifying Interfacial Electric Fields and Local Crystallinity in Polymer–Fullerene Bulk‐Heterojunction Solar Cells

The challenges of experimentally probing the physical and electronic structures of the highly intermixed organic semiconductor blends that comprise active layers in high‐performance organic photovoltaic (OPV) cells ultimately limit the fundamental understanding of the device performance. We use Fourier‐transform IR (FTIR)‐absorption spectroscopy to quantitatively determine the interfacial electric field in blended poly(3‐hexylthiophene) (P3HT):phenyl‐ C61‐butyric acid methyl ester (PCBM) thin films. The interfacial electric field is ≈0.2 V nm^?1 in the as‐spun film and blends annealing at temperatures as high as 150 °C, which is the optimal annealing temperature in terms of OPV performance. The field decreases to a negligible value upon further annealing to 170 °C, at which temperature PCBM changes from amorphous to crystalline and the open‐circuit voltage of the solar cell decreases from 0.62 to 0.4 V. In addition, our measurements also allow determination of the absolute degree of crystallinity within the acceptor material. The roles of interfacial field and local crystallinity in OPV device performance are discussed.     

Diphenylmethanofullerenes: New and Efficient Acceptors in Bulk‐Heterojunction Solar Cells

A novel fullerene derivative, 1,1‐bis(4,4′‐dodecyloxyphenyl)‐(5,6) C₆₁, diphenylmethanofullerene (DPM‐12), has been investigated as a possible electron acceptor in photovoltaic devices, in combination with two different conjugated polymers poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐para‐phenylene vinylene] (OC₁C₁₀‐PPV) and poly[3‐hexyl thiophene‐2,5‐diyl] (P3HT). High open‐circuit voltages, V_OC = 0.92 and 0.65 V, have been measured for OC₁C₁₀‐PPV:DPM‐12‐ and P3HT:DPM‐12‐based devices, respectively. In both cases, V_OC is 100 mV above the values measured on devices using another routinely used fullerene acceptor, [6,6]‐phenyl‐C₆₁ butyric acid methyl ester (PCBM). This is somewhat unexpected when taking into account the identical redox potentials of both acceptor materials at room temperature. The temperature‐dependent V_OC reveals, however, the same effective bandgap (HOMO_Polymer–LUMO_Fullerene; HOMO = highest occupied molecular orbital, LUMO = lowest unoccupied molecular orbital) of 1.15 and 0.9 eV for OC₁C₁₀‐PPV and P3HT, respectively, independent of the acceptor used. The higher V_OC at room temperature is explained by different ideality factors in the dark‐diode characteristics. Under white‐light illumination (80 mW cm^–2), photocurrent densities of 1.3 and 4.7 mA cm^–2 have been obtained in the OC₁C₁₀‐PPV:DPM‐12‐ and P3HT:DPM‐12‐based devices, respectively. Temperature‐dependent current density versus voltage characteristics reveal a thermally activated (shallow trap recombination limited) photocurrent in the case of OC₁C₁₀‐PPV:DPM‐12, and a nearly temperature‐independent current density in P3HT:DPM‐12. The latter clearly indicates that charge carriers traverse the active layer without significant recombination, which is due to the higher hole‐mobility–lifetime product in P3HT. At the same time, the field‐effect electron mobility in pure DPM‐12 has been found to be μ_e = 2 × 10^–4 cm² V^–1 s^–1, that is, forty‐times lower than the one measured in PCBM (μ_e = 8 × 10^–3 cm² V^–1 s^–1).     

Time‐Dependent Morphology Evolution by Annealing Processes on Polymer:Fullerene Blend Solar Cells

Changes in the nanoscale morphologies of the blend films of poly (3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM), for high‐performance bulk‐heterojunction (BHJ) solar cells, are compared and investigated for two annealing treatments with different morphology evolution time scales, having special consideration for the diffusion and aggregation of PCBM molecules. An annealing condition with relatively fast diffusion and aggregation of the PCBM molecules during P3HT crystallization results in poor BHJ morphology because of prevention of the formation of the more elongated P3HT crystals. However, an annealing condition, accelerating PCBM diffusion after the formation of a well‐ordered morphology, results in a relatively stable morphology with less destruction of crystalline P3HT. Based on these results, an effective strategy for determining an optimized annealing treatment is suggested that considers the effect of relative kinetics on the crystallization of the components for a blend film with a new BHJ materials pair, upon which BHJ solar cells are based.     

Effect of Temperature and Illumination on the Electrical Characteristics of Polymer–Fullerene Bulk‐Heterojunction Solar Cells

The current–voltage characteristics of ITO/PEDOT:PSS/OC₁C₁₀‐PPV:PCBM/Al solar cells were measured in the temperature range 125–320 K under variable illumination, between 0.03 and 100 mW cm^–2 (white light), with the aim of determining the efficiency‐limiting mechanism(s) in these devices, and the temperature and/or illumination range(s) in which these devices demonstrate optimal performance. (ITO: indium tin oxide; PEDOT:PSS: poly(styrene sulfonate)‐doped poly(ethylene dioxythiophene); OC₁C₁₀‐PPV: poly[2‐methoxy‐5‐(3,7‐dimethyl octyloxy)‐1,4‐phenylene vinylene]; PCBM: phenyl‐C₆₁ butyric acid methyl ester.) The short‐circuit current density and the fill factor grow monotonically with temperature until 320 K. This is indicative of a thermally activated transport of photogenerated charge carriers, influenced by recombination with shallow traps. A gradual increase of the open‐circuit voltage to 0.91 V was observed upon cooling the devices down to 125 K. This fits the picture in which the open‐circuit voltage is not limited by the work‐function difference of electrode materials used. The overall effect of temperature on solar‐cell parameters results in a positive temperature coefficient of the power conversion efficiency, which is 1.9 % at T = 320 K and 100 mW cm^–2 (2.5 % at 0.7 mW cm^–2). The almost‐linear variation of the short‐circuit current density with light intensity confirms that the internal recombination losses are predominantly of monomolecular type under short‐circuit conditions. We present evidence that the efficiency of this type of solar cell is limited by a light‐dependent shunt resistance. Furthermore, the electronic transport properties of the absorber materials, e.g., low effective charge‐carrier mobility with a strong temperature dependence, limit the photogenerated current due to a high series resistance, therefore the active layer thickness must be kept low, which results in low absorption for this particular composite absorber.     

Formation Mechanism of Fullerene Cation in Bulk Heterojunction Polymer Solar Cells

The charge carrier dynamics in blend films of [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) and conjugated polymers with different ionization potentials are measured using transient absorption spectroscopy to study the formation mechanism of PCBM radical cation, which was previously discovered for blend films of poly[2‐methoxy‐5‐(3,7‐dimethyloctyloxy)‐1,4‐phenylenevinylene] (MDMO‐PPV) and PCBM. On a nanosecond time scale after photoexcitation, polymer hole polaron and PCBM radical anion are observed but no PCBM radical cation is found in the blends. Subsequently, the fraction of polymer hole polarons decreases and that of PCBM radical cations increases with time. Finally, the fraction of PCBM radical cations becomes constant on a microsecond time scale. The final fraction of PCBM radical cation is dependent on the ionization potential of polymers but independent of the excitation wavelength. These findings show that the formation of PCBM radical cation is due to hole injection from polymer to PCBM domains. Furthermore, the energetic conditions for such hole injection in polymer/PCBM blend films are discussed on the basis of Monte Carlo analysis for hole hopping in a disordered donor/acceptor heterojunction with varying energetic parameters.     

Effects of Annealing on the Nanomorphology and Performance of Poly(alkylthiophene):Fullerene Bulk‐Heterojunction Solar Cells

The evolution of nanomorphology within thin solid‐state films of poly(3‐alkylthiophene):[6,6]‐phenyl‐C₆₁ butyric acid methyl ester (P3AT:PCBM) blends during the film formation and subsequent thermal annealing is reported. In detail, the influence of the P3AT's alkyl side chain length on the polymer/fullerene phase separation is discussed. Butyl, hexyl, octyl, decyl, and dodecyl side groups are investigated. All of the P3ATs used were regioregular. To elucidate the nanomorphology, atomic force microscopy (AFM), X‐ray diffraction, and optical spectroscopy are applied. Furthermore, photovoltaic devices of each of the different P3ATs have been constructed, characterized, and correlated with the nanostructure of the blends. It is proposed that the thermal‐annealing step, commonly applied to these P3AT:PCBM blend films, controls two main issues at the same time: a) the crystallization of P3AT and b) the phase separation and diffusion of PCBM. The results show that PCBM diffusion is the main limiting process for reaching high device performances.     

Dispersion‐Dominated Photocurrent in Polymer:Fullerene Solar Cells

Organic bulk heterojunction solar cells are often regarded as near‐equilibrium devices, whose kinetics are set by well‐defined charge carrier mobilities, and relaxation in the density of states is commonly ignored or included purely phenomenologically. Here, the motion of photocreated charges is studied experimentally with picosecond time resolution by a combination of time‐resolved optical probing of electric field and photocurrent measurements, and the data are used to define parameters for kinetic Monte Carlo modelling. The results show that charge carrier motion in a prototypical polymer:fullerene solar cell under operational conditions is orders of magnitude faster than would be expected on the basis of corresponding near‐equilibrium mobilities, and is extremely dispersive. There is no unique mobility. The distribution of extraction times of photocreated charges in operating organic solar cells can be experimentally determined from the charge collection transients measured under pulsed excitation. Finally, a remarkable distribution of the photocurrent over energy is found, in which the most relaxed charge carriers in fact counteract the net photocurrent.     

Solution‐Processed Bulk‐Heterojunction Solar Cells Based on Monodisperse Dendritic Oligothiophenes

A novel family of soluble conjugated dendritic oligothiophenes (DOTs) as monodisperse 3D macromolecular architectures was characterized with respect to optical and redox properties in solution and in solid films. Band gaps of 2.5–2.2 eV, typical for organic semiconductors, were determined as well as HOMO/LUMO energy levels ideal for efficient electron transfer to acceptors such as [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) identifying them as suitable materials for solar cell applications. Solution‐processed bulk‐heterojunction solar cells using DOTs as electron donor and PCBM as acceptor were prepared and investigated. High open‐circuit voltages V_OC of 1.0 V and power‐conversion efficiencies up to 1.72% were obtained for the DOT‐based devices. The higher generations DOTs provide the highest efficiencies. Based on the monodispersity of the DOTs, an analysis of the molar ratio between donor and acceptor in the blended film was possible leading to an optimal value of five to six thiophene units per PCBM.     

Influence of Phase Segregation on Recombination Dynamics in Organic Bulk‐Heterojunction Solar Cells

The recombination dynamics of charge carriers in organic bulk‐heterojunction (BHJ) solar cells made of the blend system poly(2,5‐bis(3‐dodecylthiophen‐2‐yl)thieno[2,3‐b]thiophene) (pBTCT‐C₁₂):[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) with a donor–acceptor ratio of 1:1 and 1:4 are studied here. The techniques of charge‐carrier extraction by linearly increasing voltage (photo‐CELIV) and, as local probe, time‐resolved microwave conductivity are used. A difference of one order of magnitude is observed between the two blends in the initially extracted charge‐carrier concentration in the photo‐CELIV experiment, which can be assigned to an enhanced geminate recombination that arises through a fine interpenetrating network with isolated phase regions in the 1:1 pBTCT‐C₁₂:PC₆₁BM BHJ solar cells. In contrast, extensive phase segregation in 1:4 blend devices leads to an efficient polaron generation that results in an increased short‐circuit current density of the solar cells. For both studied ratios a bimolecular recombination of polarons is found using the complementary experiments. The charge‐carrier decay order of above two for temperatures below 300 K can be explained on the basis of a release of trapped charges. This mechanism leads to delayed bimolecular recombination processes. The experimental findings can be generalized to all polymer:fullerene blend systems allowing for phase segregation.     

Quinacridone‐Based Electron Transport Layers for Enhanced Performance in Bulk‐Heterojunction Solar Cells

A water/alcohol‐soluble small molecule based on the commercially available pigment quinacridone is employed as an electron transport layer in organic photovoltaics. The quinacridone derivative is utilized in solution‐processed bulk‐heterojunction solar cells to improve primarily the fill factor of the devices, contributing to an upwards of 19% enhancement in the power conversion efficiency relative to the control devices with no electron transport layer. The facile synthesis of the quinacridone derivative coupled with the ease of device fabrication via solution processing provide a simple, yet effective means of improving the performance of existing organic photovoltaic cells.     

Hole Transport in Poly(phenylene vinylene)/Methanofullerene Bulk‐Heterojunction Solar Cells

A fundamental limitation of the photocurrent of solar cells based on a blend of poly(2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐p‐phenylene vinylene) (MDMO‐PPV) and [6,6]‐phenyl C₆₁‐butyric acid methyl ester (PCBM) is caused by the mobility of the slowest charge‐carrier species, the holes in the MDMO‐PPV. In order to allow the experimentally observed photocurrents electrostatically, a hole mobility of at least 10^–8 m² V^–1 s^–1 is required, which exceeds the observed hole mobility in pristine MDMO‐PPV by more than two orders of magnitude. However, from space‐charge‐limited conduction, admittance spectroscopy, and transient electroluminescence measurements, we found a hole mobility of 2 × 10^–8 m² V^–1 s^–1 for the MDMO‐PPV phase in the blend at room temperature. Consequently, the charge‐carrier transport in a MDMO‐PPV:PCBM‐based solar cell is much more balanced than previously assumed, which is a necessary requirement for the reported high fill factors of above 50 %.     

Enhanced Thermal Stability and Efficiency of Polymer Bulk‐Heterojunction Solar Cells by Low‐Temperature Drying of the Active Layer

This study addresses two key issues, stability and efficiency, of polymer solar cells based on blended poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) by demonstrating a film‐forming process that involves low‐temperature drying (?5 °C) and subsequent annealing of the active layer. The low‐temperature process achieves 4.70% power conversion efficiency (PCE) and ～1250 h storage half‐life at 65 °C, which are significant improvements over the 3.39% PCE and ～143 h half‐life of the regular room‐temperature process. The improvements are attributed to the enhanced nucleation of P3HT crystallites as well as the minimized separation of the P3HT and PCBM phases at the low drying temperature, which upon post‐drying annealing results in a morphology consisting of small PCBM‐rich domains interspersed within a densely interconnected P3HT crystal network. This morphology provides ample bulk‐heterojunction area for charge generation while allowing for facile charge transport; moreover, the P3HT crystal network serves as an immobile frame at heating temperatures less than the melting point (T_m) of P3HT, thus preventing PCBM/P3HT phase separation and the corresponding device degradation.     

High‐Performance Air‐Processed Polymer–Fullerene Bulk Heterojunction Solar Cells

High photovoltaic device performance is demonstrated in ambient‐air‐processed bulk heterojunction solar cells having an active blend layer of organic poly(3‐hexylthiophene) (P3HT): [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM), with power conversion efficiencies as high as 4.1%, which is comparable to state‐of‐the‐art bulk heterojunction devices fabricated in air‐free environments. High‐resolution transmission electron microscopy is combined with detailed analysis of electronic carrier transport in order to quantitatively understand the effects of oxygen exposure and different thermal treatments on electronic conduction through the highly nanostructured active blend network. Improvement in photovoltaic device performance by suitable post‐fabrication thermal processing results from the reduced oxygen charge trap density in the active blend layer and is consistent with a corresponding slight increase in thickness of an ～4 nm aluminum oxide hole‐blocking layer present at the electron‐collecting contact interface.     

Morphology Control in Solution‐Processed Bulk‐Heterojunction Solar Cell Mixtures

The efficiency of bulk‐heterojunction solar cells is very sensitive to the nanoscale structure of the active layer. In the past, the final morphology in solution‐processed devices has been controlled by varying the casting solvent and by curing the layer using heat tempering or solvent soaking. A recipe for making the “best‐performing” morphology can be achieved using these steps. This article presents a review of several new techniques that have been developed to control the morphology in polymer/fullerene heterojunction mixtures. The techniques fall into two broad categories. First, the morphology can be controlled by preparing nanoparticle suspensions of one component. The size and shape of the nanoparticles in solution determine the size and shape of the domain in a mixed layer. Second, the morphology can be controlled by adding a secondary solvent or an additive that more strongly affects one component of the mixture during drying. In both cases, the as‐cast efficiency of the solar cell is improved with respect to the single‐solvent case, which strongly argues that morphology control is an issue that will receive increasing attention in future research.     

Fluorenone‐Based Molecules for Bulk‐Heterojunction Solar Cells: Synthesis,Characterization, and Photovoltaic Properties

A series of four conjugated molecules consisting of a fluorenone central unit symmetrically coupled to different oligothiophene segments are conceptually designed and synthesized to provide new electroactive materials for application in photovoltaic devices. The combination of electron‐donating oligothiophene building blocks with an electron‐accepting fluorenone unit results in the emergence of a new band assigned to an intramolecular charge transfer transition that gives rise to the extension of the absorption spectral range of the resulting molecules. Detailed spectroscopic and voltammetric investigations show that all studied molecules have highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) level positions, which make them good candidates for the application as electron‐donors in bulk‐heterojunction photovoltaic cells, with (6,6)‐phenyl‐C61‐butyric acid methyl ester (PCBM)‐C₆₀ as electron acceptor component. Moderate device performances, with power conversion efficiencies (PCEs) comprised between 0.3 and 0.6%, were obtained with rigid molecules, containing either the bridging units between the thiophene rings, i.e., (2,7‐bis(4,4′‐dioctyl‐cyclopenta[2,1‐b:3,4‐b′]dithiophen‐2‐yl)‐fluoren‐9‐one (SCPTF) and 2,7‐bis(4‐(dioctylmethylene)‐cyclopenta[2,1‐b:3,4‐b′]dithiophen‐5‐yl)‐fluoren‐9‐one (MCPTF) or a vinylene unit 2,7‐bis(5‐[(E)‐1,2‐bis(3‐octylthien‐2‐yl)ethylene])‐fluoren‐9‐one (TVF), whereas with (2,7‐bis‐(3,3?‐dioctyl‐[2,2′;5′,2″;5″,2?]quaterthiophen‐5‐yl)‐fluoren‐9‐one (QTF) PCE up to 1.2% (under AM 1.5 illumination, 100 mW cm^?2, active area 0.28 cm²) was obtained. The strong π‐stacking interactions in the solid state for this oligomer leading to improved morphology could explain the good performances of QTF‐based devices, which rank among the highest recorded for non‐polymeric materials. Consequently, fluorenone‐based non‐polymeric molecules constitute highly attractive materials for solution‐processable solar cell applications.     

Recombination‐Limited Photocurrents in Low Bandgap Polymer/Fullerene Solar Cells

The charge transport and photogeneration in solar cells based on the low bandgap‐conjugated polymer, poly[2,6‐(4,4‐bis‐(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b; 3,4‐b′]dithiophene)‐alt‐4,7‐(2,1,3‐benzothiadiazole)] (PCPDTBT) and fullerenes is studied. The efficiency of the solar cells is limited by a relatively low fill factor, which contradicts the observed good and balanced charge transport in these blends. Intensity dependent measurements display a recombination limited photocurrent, characterized by a square root dependence on effective applied voltage, a linear dependence on light intensity and a constant saturation voltage. Numerical simulations show that the origin of the recombination limited photocurrent stems from the short lifetime of the bound electron‐hole pairs at the donor/acceptor interface.     

Charge Transport and Photocurrent Generation in Poly(3‐hexylthiophene): Methanofullerene Bulk‐Heterojunction Solar Cells

The effect of controlled thermal annealing on charge transport and photogeneration in bulk‐heterojunction solar cells made from blend films of regioregular poly(3‐hexylthiophene) (P3HT) and methanofullerene (PCBM) has been studied. With respect to the charge transport, it is demonstrated that the electron mobility dominates the transport of the cell, varying from 10^–8 m² V^–1 s^–1 in as‐cast devices to ≈3 × 10^–7 m² V^–1 s^–1 after thermal annealing. The hole mobility in the P3HT phase of the blend is dramatically affected by thermal annealing. It increases by more than three orders of magnitude, to reach a value of up to ≈ 2 × 10^–8 m² V^–1 s^–1 after the annealing process, as a result of an improved crystallinity of the film. Moreover, upon annealing the absorption spectrum of P3HT:PCBM blends undergo a strong red‐shift, improving the spectral overlap with solar emission, which results in an increase of more than 60 % in the rate of charge‐carrier generation. Subsequently, the experimental electron and hole mobilities are used to study the photocurrent generation in P3HT:PCBM devices as a function of annealing temperature. The results indicate that the most important factor leading to a strong enhancement of the efficiency, compared with non‐annealed devices, is the increase of the hole mobility in the P3HT phase of the blend. Furthermore, numerical simulations indicate that under short‐circuit conditions the dissociation efficiency of bound electron–hole pairs at the donor/acceptor interface is close to 90 %, which explains the large quantum efficiencies measured in P3HT:PCBM blends.