Effect of filler treatments on rheological behavior of calcium carbonate and talc‐filled polypropylene hybrid composites

Commercial stearic acid treated calcium carbonate (CaCO₃) was used to make a comparative study on rheological behavior of the CaCO₃ and talc‐filled polypropylene (PP) hybrid composites with nontreated filler. Apparent shear viscosity and extrudate swell were investigated with variation of filler ratio and temperature with 30% by weight total of filler was used in PP composite. The Shimadzu capillary rheometer was used to evaluate shear viscosity and shear rate of the composite. It was found that the shear viscosities decrease with increasing shear rate. The apparent shear viscosity of the composite containing the stearic acid treated is slightly lower than untreated filler. Shear thickening behavior at higher shear rate has also shown by 15/15 treated composites at higher temperature about 220°C and investigation by SEM has proved that filler being densely packed at that condition. Treated composites also exhibit lower swelling ratio value than untreated composite, and swelling ratio also decreases linearly with increasing temperature and the die length–diameter ratio. It is believed that dispersion of filler play an important role not only on shear viscosity but also on swelling ratio of PP composite. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5421–5426, 2006     

Mechanical,flow, and morphological properties of talc‐ and kaolin‐filled polypropylene hybrid composites

Polypropylene (PP) hybrid composites have been produced by compounding two types of mineral fillers, viz., talc and kaolin with PP copolymer using a twin screw extruder. The PP hybrid composite was injection‐molded into dumbbell specimen for tensile, flexural, and impact properties characterizations. MFI and SEM studies were used to characterize the flow and morphological properties of the PP hybrid composites. The result shows that most of the hybrid composites showed a significant decrease in flow, tensile, flexural, and impact properties compared with the single filler‐filled PP composites. However, a hybridization effect was seen for the PPT20K10 hybrid composites, through the synergistic coalescence of positive characteristics from 20 wt % of talc and 10 wt % of kaolin. This hybrid formulation have given an economically advantageous material with the mechanical properties (tensile, flexural, and impact) comparable to those of the talc‐filled PP composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 434–441, 2007     

Temperature effect on the swelling of PAAm‐κ‐carrageenan composites

The steady‐state fluorescence (SSF) technique was used for studying swelling of disc‐shaped polyacrylamide (PAAm)‐κ‐carrageenan (κC) composites which were prepared by free‐radical crosslinking copolymerization at 80°C. Pyranine was introduced as a fluorescence probe during polymerization. Swelling experiments were performed in water at various temperatures by real‐time monitoring of the pyranine (Py) fluorescence intensity, I which decreased as swelling proceeded. Stern–Volmer equation is modified for low quenching efficiencies to interpret the behavior of Py intensity during the swelling of PAAm‐κC composites. The Li‐Tanaka equation was used to determine the swelling time constants, τ₁, and cooperative diffusion coefficients, D₀, from fluorescence intensity, weight, and volume variations of the composites at various temperatures. It was observed that τ₁ first decreased up to 40°C and then increased; naturally, D₀ increased up to 40°C and then decrease for all κC content gels. Swelling activation energies, ΔE, were measured for the swelling composites, which are found to be exothermic and endothermic in between 30–40 and 40–60°C, respectively. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Solution behavior of water‐soluble poly(acrylamide‐co‐sulfobetaine) with intensive antisalt performance as an enhanced oil‐recovery chemical

In the process of oilfield development, salt tolerance is an important property for enhanced oil‐recovery (EOR) chemicals. In this study, we synthesized two acrylamide‐based sulfobetaine copolymers containing 2‐hydroxy‐3‐[(3‐methacrylamidopropyl)dimethylammonio]propane sulfonate (SHPP) or 3‐(4‐acry‐loyl‐1‐methyl‐piperazinio)‐2‐hydroxypropane sulfonate (SHMP). The interactions between these two copolymers and inorganic salts were compared, and the apparent viscosity (η_app) behaviors of copolymer–salt solutions at different shear rates and temperatures were investigated. We found that the η_app of PAPP and PAMP showed intensive antisalt performance, exhibiting an excellent antipolyelectrolyte effect. The η_app retention value of 30,000 mg/L PAMP in brine was 86.47 mPa s at 510 s^?1, and when the temperature was increased to 90 °C, it was 99.73 mPa s; this was better than that of PAPP under the same conditions. Therefore, PAMP was more applicable as an EOR chemical that have outstanding salt tolerance and temperature resistance. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46235     

Solvothermal synthesis of organically modified α‐zirconium phosphate‐based polystyrene nanocomposites and thermal stability

Polystyrene/α‐zirconium phosphate (PS/OZrP) nanocomposites were prepared based on the organically modified α‐ZrP(OZrP) with hexadecyltrimethyl ammonium bromide (C16) by solvothermal technique and solution refluxing. The structure of the PS/OZrP composites was characterized by X‐ray diffraction and high‐resolution electronic microscopy. The thermal behaviors of the composites obtained were investigated by thermogravimetric analysis. The maximum decomposition temperatures (T_max) of PS/OZrP nanocomposites prepared by solvothermal method increased gradually from 431 to 458°C with the increase of the OZrP loading from 0 to 20 wt %, and the amounts of the charred residue at 600°C (char wt %) had a remarkable increase from 1.6 to 17.1 wt %, respectively. Moreover, the TG results of the nanocomposites prepared by solvothermal method have more obvious enhancement in the thermal stabilities and especially in the amount of charred residue at 600°C (char wt %), which has a double increase from 4.2 to 8.5 wt % at the content of 10 wt % OZrP than by solution refluxing. All results suggested that the solvothermal method is an effective way for the preparation of PS/OZrP nanocomposites with the intercalated nanostructure, which led to the obviously improved thermal stability. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci 122:593–598, 2011     

Effect of compatibilizers on water absorption kinetics of polypropylene/wood flour foamed composites

Polypropylene (PP)/wood flour foamed composites were prepared by taking PP:wood flour in the ratios of 100 : 0, 90 : 10, 80 : 20, 70 : 30, and 60 : 40 (w/w), with and without compatibilizers like maleic anhydride‐treated wood flour and maleic anhydride‐grafted PP (PPgMA). The foamed composite samples were employed for water swelling at 27°C, 70°C, and in steam. The absorption of water increased with increase in filler contents for all three‐temperature conditions. The maleic anhydride‐treated wood flour and PPgMA showed reduction in water swelling, and the best one was in case of the PPgMA‐foamed composites for respective conditions. Diffusion, sorption, and permeation coefficients were determined to study the absorption kinetics. FTIR spectra were also recorded for 30 wt % of filler loading for all the composites, which showed the effect of compatibilizers on reduction in water absorption in foamed PP/wood flour composites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2530–2537, 2006     

Rheological behavior of brominated isobutylene‐co‐paramethylstyrene: Effect of fillers,oil and blending with EPDM

The melt flow properties of unfilled and filled brominated isobutylene‐co‐paramethylstyrene (BIMS) were measured by means of a capillary viscometer at three different temperatures (90°C, 110°C and 130°C) and four different shear rates (61, 122, 245 and 306 s^?1). The effect of addition of EPDM rubber on melt flow properties of unfilled BIMS was also studied. Evaluation of the processability was done by measuring the extrudate roughness (ER) of the extrudates obtained from the MPT. The viscosity of the systems decreased with the shear rate, indicating their pseudoplastic or shear thinning nature. As expected, the viscosity of BIMS increased with the addition of fillers and decreased with the addition of oil. For the neat systems, viscosity increased with the addition of EPDM, and the blends showed a positive deviation, indicating interdiffusion of the polymer chains across the phase boundaries. The activation energy of the filled systems at constant filler loading increased with increasing filler surface area (N330 > N550 > N774, each at 30 phr loading), and filler loading (50 > 30 > 10 phr, for N330) and decreased with the addition of oil (2.5 > 5.0 > 7.5 phr, for system containing 30 phr of N330). The silica filled system showed a higher activation energy and ER than the carbon black‐filled systems. With addition of N330 and N550 carbon blacks to BIMS, the extrudate roughness (ER) decreased, whereas it increased with the addition of N774 carbon black. With an increase in filler loading, ER initially increased and then decreased as compared to the neat system. For the filled systems, ER initially decreased up to 5 phr of oil, beyond which it increased.     

Hydrogel composites based on linear low‐density polyethylene‐g‐poly (acrylic acid)/Kaolin or halloysite nanotubes

Two series of superabsorbent hydrogel composites were prepared using waste linear low‐density polyethylene, acrylic acid, and two types of clays including kaolin and halloysite nanotube (HNT) through emulsion polymerization. The effects of the clay content on Water absorbency were investigated to obtain a high swelling capacity. The prepared samples were characterized using FTIR, SEM, thermogravimetric analysis, XRD, solid‐state ¹³C Nuclear Magnetic Resonance spectroscopy, and ²⁹Si NMR. SEM characterization of the samples showed that the hydrogel composites have more pores and a higher swelling ratio than the clay‐free hydrogels. The hydrogel composite containing kaolin had higher water absorbency compared to the hydrogel composites with HNT. The swelling behavior of the hydrogel composite was investigated in various saline solutions. The hydrogel composite containing 5 wt % kaolin had the highest water absorbency (760 g/g in distilled water). © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40101.     

Development of environmentally friendly high‐density polyethylene and turmeric spent composites: Physicomechanical,thermal, and morphological studies

High‐density polyethylene (HDPE)/turmeric spent (TS) composites were prepared by the extrusion of an HDPE resin with 5, 10, 15, or 20 wt % TS. HDPE granules and TS master‐batch flakes were compounded on a corotating and intermeshing twin‐screw extruder. The extrudate strands were cut into pellets and injection‐molded to make test specimens. These specimens were tested for physicomechanical properties such as the tensile, flexural, and impact strengths, surface hardness, abrasion resistance, density, and water absorption and thermal characteristics such as the heat distortion temperature (HDT) and melt flow index (MFI). Test results revealed that the incorporation of TS affected the tensile, flexural, and Izod impact strengths of the HDPE/TS composites to some extent, whereas the tensile modulus increased from 606.9 to 752.0 N/mm² and the HDT increased from 61 to 65°C. Furthermore, the addition of TS yielded only marginal variations in the surface hardness, abrasion resistance, density, water absorption, and MFI values of the composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of Al2O3 addition on thermo‐electrical properties of polymer composites: An experimental investigation

To develop a new class of composites with adequately high thermal conductivity and suitably controlled dielectric constant for electronic packages and printed circuit board applications, polymer composites are prepared with microsized Al₂O₃ particle as filler having an average particle size of 80–100 μm. Epoxy and polypropylene (PP) are chosen as matrix materials for this study. Fabrication of epoxy‐based composite is done by hand lay‐up technique and its counterpart PP‐based composite are fabricated by compression molding technique with filler content ranging from 2.5–25 vol%. Effects of filler loading on various thermal properties like effective thermal conductivity (k_eff), glass transition temperature (T_g), coefficient of thermal expansion (CTE) and electrical property like dielectric constant (ε_c) of composites are investigated experimentally. In addition, physical properties like density and void fraction of the composites along with there morphological features are also studied. The experimental findings obtained under controlled laboratory conditions are interpreted using appropriate theoretical models. Results show that with addition of 25 vol% of Al₂O₃, k_eff of epoxy and PP improve by 482% and 498% respectively, T_g of epoxy increases from 98°C to 116°C and that of PP increases from −14.9°C to 3.4°C. For maximum filler loading of 25 vol% the CTE decreases by 14.8% and 26.4% for epoxy and PP respectively whereas the dielectric constants of the composites get suitably controlled simultaneously. POLYM. COMPOS., 36:102–112, 2015. © 2014 Society of Plastics Engineers     

Effect of silane coupling agent on the curing,tensile, thermal,and swelling properties of ethylene‐propylene‐diene monomer rubber (EPDM)/mica composites

The influence of silane (bis[3‐triethoxysilylpropyl] tetrasulfide) coupling agent on the properties of ethylene‐propylene‐diene monomer rubber (EPDM)/mica composites was studied. Both EPDM/mica composites with silane and those without silane were compounded by using a two‐roll mill at various filler loadings (i.e., 100/0, 100/10, 100/30, 100/50, 100/70). The tensile and thermal properties as well as the fracture surfaces of the composites were investigated by using an Instron Universal Testing Machine, a thermal gravimetric analyzer, and a field emission scanning electron microscope. The results indicated that the optimum cure time (t₉₀) and scorch time (t_s2) values were shorter, whereas the maximum torque (M_H) value was slightly higher, for EPDM/mica composites with silane compared to those without silane. The tensile properties, modulus at 100% elongation, and modulus at 300% elongation increased for the composites made with silane, and the optimum filler loading for those properties was 50 parts by weight per hundred parts of rubber. In addition, thermal stability and swelling ratio for both composites improved with increased filler loading. However, the composites with silane showed better thermal stability and swelling ratio because of stronger linkage at the rubber‐filler boundary, which promoted filler dispersion. J. VINYL ADDIT. TECHNOL., 20:116–121, 2014. © 2014 Society of Plastics Engineers     

PTCR characteristics of poly(styrene‐co‐acrylonitrile) copolymer/stainless steel powder composites

Positive temperature coefficient of resistivity (PTCR) characteristics of poly(styrene‐co‐acrylonitrile) copolymer (SAN)/stainless steel (SS) powder (80 wt %) composites prepared by melt‐mixing method has been investigated with reference to SAN/carbon black (CB) composites. The SAN/CB (10 wt %) composites showed a sudden rise in resistivity (PTC trip) at 125°C, above the glass transition temperature (T_g) of SAN (T_g ≈ 107°C). However, the PTC trip temperature of SAN/SS (80 wt %) composites appeared at 94°C, well below the T_g of SAN. Addition of 1 phr of nanoclay increased the PTC trip temperature of SAN/CB (10 wt %) composites to 130°C, while SAN/SS (80 wt %)/clay (1 phr) nanocomposites showed the PTC trip at 101°C. We proposed that the mismatch in coefficient of thermal expansion (CTE) between SAN and SS played a key role that led to a disruption in continuous network structure of SS even at a temperature below the T_g of SAN. The dielectric properties study of SAN/SS (80 wt %) composites indicated possible use of the PTC composites as dielectric material. DMA results showed higher storage modulus of SAN/SS composites than the SAN/CB composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Rheological behaviors of PVA/H2O solutions of high‐polymer concentration

The dynamic viscoelastic properties of poly(vinyl alcohol) (PVA)/H₂O solutions with concentrations of 10 to 25 wt % have been characterized by controlled‐stress rheometry at 30°C. Parameters relating to the linear and nonlinear viscoelasticities include complex viscosity (η*), storage modulus (G′), loss tangent (tan δ), relaxation time (λ), thixotropy, and creep. Change curves of η*, G′, tanδ, and λ with frequency (ω) have been obtained for the PVA/H₂O solutions. Creep and recovery testing yielded compliance (J′) curves with loading and unloading. Shear stress versus rate profiles of the PVA solutions have been obtained through thixotropic measurements. The PVA concentration has been found to have a profound influence on the rheological properties of the aqueous solutions. Four aqueous solutions of 10, 15, 20, and 25 wt % PVA at 30°C exhibited shear‐thinning and showed different transition behaviors of η* and G′ with frequency, and different degrees of creep under constant stress to recovery with time. The 10 wt % PVA solution was viscous and displayed the lowest η* and G′; the 25 wt % PVA solution was viscoelastic and displayed the highest η* and G′; the 15 and 20 wt % PVA solutions showed η* and G′ values and creep to recovery behaviors intermediate between those of the 10 wt % and 25 wt % PVA solutions. The different rheological properties of these PVA/H₂O solutions are considered to correlate with interchain hydrogen bonds and shear‐induced orientation in the solutions. Shearing is able to break the intrachain and interchain hydrogen bonds, and, at the same time, the orientation creates new interchain hydrogen bonding. The reorganization of hydrogen‐bonding mode contributes to the transitions of the macroscopic viscoelasticity with frequency. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of polyurethane/Mg‐Al layered double hydroxide nanocomposites

Layered double hydroxide (LDH) is a new type of nanofiller, which improves the physicochemical properties of the polymer matrix. In this study, 1, 3, 5, and 8 wt % of dodecyl sulfate‐intercalated LDH (DS‐LDH) has been used as nanofiller to prepare a series of thermoplastic polyurethane (PU) nanocomposites by solution intercalation method. PU/DS‐LDH composites so formed have been characterized by X‐ray diffraction and transmission electron microscopy analysis which show that the DS‐LDH layers are exfoliated at lower filler (1 and 3 wt %) loading followed by intercalation at higher filler (8 wt %) loading. Mechanical properties of the nanocomposite with 3 wt % of DS‐LDH content shows 67% improvement in tensile strength compared to pristine PU, which has been correlated in terms of fracture behavior of the nanocomposites using scanning electron microscope analysis. Thermogravimetric analysis shows that the thermal stability of the nanocomposite with 3 wt % DS‐LDH content is ≈ 29°C higher than neat PU. Limiting oxygen index of the nanocomposites is also improved from 19 to 23% in neat PU and PU/8 wt% DS‐LDH nanocomposites, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Comparison of the mechanical properties and interfacial interactions between talc,kaolin, and calcium carbonate filled polypropylene composites

Three types of mineral fillers—talc, calcium carbonate (CaCO₃), and kaolin (10–40 wt % filler loadings)—were compounded with polypropylene (PP) with a twin‐screw extruder. The composites were injection‐molded, and the effects of the filler loading on the mechanical, flow, and thermal properties for the three different types of filled composites were investigated. The aim was to compare their properties and to deduce prospective filler combinations that would yield hybrid PP composites in following studies. The results showed that in most cases, the strength and stiffness of the talc‐filled PP composites was significantly higher than those of the CaCO₃‐ and kaolin‐filled PP composites. However, CaCO₃, being a nonreactive filler, increased the toughness of PP. The kaolin‐filled PP composites also showed some improvement in terms of strength and stiffness, although the increases in these properties were not as significant as those of the talc‐filled PP composites. The effects of interfacial interactions between the fillers and PP on the mechanical properties were also evaluated with semiempirical equations. The nucleating ability of all three fillers was studied with differential scanning calorimetry, and the strongest nucleating agent of the three was talc, followed by CaCO₃ and kaolin. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3315–3326, 2004     

Effect of the structure of silane‐coupling agent on dynamic mechanical properties of dental resin‐nanocomposites

This work was aimed at the study by dynamic mechanical analysis (DMA) of dental composites consisted of a Bis‐GMA/TEGDMA (50/50 wt/wt) matrix and silica nanoparticles (Aerosil OX50) as filler, silanized with various silanes. The silanes used were 3‐[(1,3(2)‐dimethacryloyloxypropyl)‐2 (3)‐oxycarbonylamido] propyltriethoxy‐silane (UDMS), 3‐methacryloxypropyl‐trimethoxysilane (MPS), octyltrimethoxysilane (OTMS), blends of UDMS/OTMS (50/50 wt/wt), or MPS/OTMS (50/50 wt/wt). The total amount of silane was kept constant at 10% by weight fraction relative to the filler weight. The silanized nanoparticles were mixed with the dimethacrylate matrix (60% filler by weight fraction). The composites were light cured and tested by DMA for the determination of storage modulus (E′), loss modulus (E″), tangent delta (tan δ), and glass transition temperature (T_g). Measurements were performed in samples immediately after curing and samples stored in water at 37°C for 1, 7, 30, or 120 days. OTMS‐composite in which OTMS does not form covalent bond with the dimethacrylate matrix showed lower elastic modulus both in dry and wet conditions. The ability of bifunctional UDMS for crosslinking was found not to increase the elastic behavior of the composite, as it was expected, compared with that of MPS‐composite, because of the high amount of the silane used. After immersion in water the elastic modulus of OTMS‐composite remained constant, while that of the other composites increased after 1 day and then remained constant up to 120 days. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Structural,thermal, morphological and dynamic mechanical characteristics of waste‐reinforced polypropylene composites: A novel approach for recycling electronic waste

An in‐depth investigation has been carried toward utilizing polymer‐rich nonmetallic fraction of printed circuit boards (PCBs) as reinforcing fillers in polypropylene (PP) composites. The influence of waste additions (up to 25 wt %) on structural, thermal, morphological, and dynamic mechanical behavior of PP composites was investigated using a range of analytical techniques. The incorporation of PCB waste was found to affect the crystalline morphology resulting in the formation of smaller spherulites. The presence of glass fibers in PCB waste promoted the formation of β‐crystal enhancing the mechanical properties of composites. Thermal analysis showed a maximum increase of ～15 °C in the crystallization onset temperature (T_co) suggesting the nucleating effect of the filler, a feature also supported by structural investigations. Polarized microscopy revealed a reduction in the spherulite size after 5 wt % PCB waste loading owing to the presence of large number of nucleation sites. The incorporation of waste also increased the thermal stability of composites increasing the final degradation temperature by up to 14 °C. Dynamic mechanical properties of PP/PCB waste composites were determined in the temperature range ?20 to 155 °C; a significant increase in the storage modulus further confirmed the reinforcing effect of waste additives. This investigation has shown that the nonmetallic fraction of PCB waste could be used as a cost‐effective reinforcing filler for PP, providing an environmental friendly route to utilize electronic waste in value‐added products. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43389.     

Study of surface‐functionalized nano‐SiO2/polybenzoxazine composites

A series of the surface‐functionalized nano‐SiO₂/polybenzoxazine (PBOZ) composites was produced, and an attempt was made to improve the toughness of PBOZ material, without sacrificing other mechanical and thermal properties. A benzoxazine functional silane coupling agent was synthesized to modify the surface of nano‐SiO₂ particles, which were then mixed with benzoxazine monomers to produce the nano‐SiO₂‐PBOZ nanocomposites. The notched impact strength and the bending strength of the nano‐SiO₂‐PBOZ nanocomposites increase 40% and 50%, respectively, only with the addition of 3 wt % nano‐SiO₂. At the same load of nano‐SiO₂, the nano‐SiO₂‐PBOZ nanocomposites exhibit the highest storage modulus and glass‐transition temperature by dynamic viscoelastic analysis. Moreover, the thermal stability of the SiO₂/PBOZ nanocomposites was enhanced, as explored by the thermogravimetric analysis. The 5% weight loss temperatures increased with the nano‐SiO₂ content and were from 368°C (of the neat PBOZ) to 379°C or 405°C (of the neat PBOZ) to 426°C in air or nitrogen with additional 3 wt % nano‐SiO₂. The weight residue of the same nanocomposite was as high as 50% in nitrogen at 800°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Melt rheology of polypropylene reinforced with polyaniline‐coated short glass fibers

This research deals with the melt rheology of isotactic polypropylene (iPP) reinforced with short glass fibers (SGF) coated with electrically conductive polyaniline (PAn). Composites containing 10, 20, and 30 wt % PAn‐SGF were studied. Moreover, a composite of 30 wt % PAn‐SGF was also prepared with a blend of iPP and PP‐grafted‐maleic anhydride (iPP/PP‐gMA). The composites showed linear viscoelastic regime at small strain amplitudes. The onset of nonlinearity decreased as the concentration of filler increased. The time‐temperature superposition principle applied to all composites. The filler increased the shear moduli (G′, G″) and the complex viscosity η*. Steady‐state shear experiments showed yield stress for the composites with 20 and 30 wt % PAn‐SGF. Strikingly, the 10 wt % composite showed higher steady state viscosity than the 20 wt %. Rheo‐optics showed that shear induced disorder of microfibers at a concentration of 10 wt %. However, at 20 wt % concentration shear aligned the microfibers along the flow axis, this would explain the anomalous steady state viscosity values. The viscosity exhibited a shear thinning behavior at high shear rates for all composites. Creep experiments showed that the filler induced greater strain recovery in the composites and that the amount of strain recovery increased as the PAn‐SGF concentration increased. However, the enhancement of strain recovery (as well as shear viscosity) was more significant when using the iPP/PP‐gMA blend, suggesting greater adhesion between this matrix and the filler PAn‐SGF. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008