Electric‐field‐driven LC lens for 3‐D/2‐D autostereoscopic display

Abstract— The use of an electric‐field‐driven liquid‐crystal (ELC) lens cell for switching between a 3‐D and 2‐D display is proposed. Due to the phase retardation of the non‐uniform LC directors, an ELC lens functions the same as a geometric lens. The parameters of an ELC for 3‐D applications are optimized through the simulation of the electrode configuration and voltage levels. A prototype was made where the ELC lens is placed in front of a liquid‐crystal display (LCD) 15 in. on the diagonal with a 99‐μm subpixel pitch. Under zero voltage, the ELC lens is a transparent medium and the users can see a clear 2‐D image. In 3‐D mode, the ELC lens array performs the same as a cylindrical lens array to the incident vertical polarization under suitable driving voltages. Placing a half‐wave plate between the LCD and ELC lens is proposed to change the polarization of the LCD to be parallel with the polarization lens direction of the ELC lens. The measurement of the horizontal luminance profile, performance of the ELC lens, and feasibility for 3‐D/2‐D switching was verified. The fabrication process for the ELC lens is compatible with the current LCD production process and enables the accurate control of the lens pitch of the ELC lens.     

Design and measurement‐based characterization of a K‐band metalens for wideband oblique‐incident spherical‐plane wave conversion

In this article, a wideband spherical‐plane wave conversion metalens (WSPCM) working in the K‐band is designed. The WSPCM consists of metamaterial elements with gradient transmission phases, which can transform the oblique‐incident spherical wave to the plane wave propagating along the direction from the source to the center of the metalens. First, a five‐layer metamaterial element with gradient transmission phase is designed using the Computer Simulation Technology software. Then, a metamaterial wedge consists of eight metamaterial elements with 30° phase gradient (that can deflect the incident plane wave by 30°) is designed to verify the phase modulation characteristic of the metamaterial element. Afterwards, a metalens is designed according to the digitized phase distribution of the dielectric lens. Finally, the electric field distribution of the emitted wave at different frequencies and different source locations (ie, oblique‐incident angles) is studied. The design is validated through simulations and measurements.     

A single‐cell‐gap transflective blue‐phase liquid crystal display based on fringe in‐plane switching electrodes

A transflective blue‐phase liquid crystal display (TRBP‐LCD) based on fringe in‐plane switching (FIS) electrodes is proposed. The proposed structure generates combined fringe and in‐plane electric fields that cause more liquid crystal (LC) molecules to reorient almost in plane above and between the pixel electrodes. The fringe field is mainly generated in the transmissive (T) region, and the horizontal electric field is mainly generated in the reflective (R) region. By optimizing the width of the pixel electrodes and the gap between two adjacent pixel electrodes, the different electric field intensity in the T and R regions contribute to balance the optical phase retardation between the T and R regions. As a result, the proposed TRBP‐LCD exhibits a low operating voltage and high optical efficiency, while it preserves a relatively simple fabrication process.     

Low‐voltage and high‐transmittance blue‐phase liquid‐crystal device with slanted electrodes

Abstract— A low‐voltage (～10 V_rms) and high‐transmittance (～90%) polymer‐stabilized blue‐phase liquid‐crystal (BPLC) device with a slanted‐electrodes structure is proposed. Unlike the vertical‐field‐switching (VFS) mode in which oblique incident light and a vertical field are employed, the proposed device utilizes normal incident light and an oblique field. The slanted electrodes generate a strong and uniform oblique electric field, which contributes in obtaining low voltage and high transmittance. Moreover, no couple films or prism sheets are needed, which helps to enhance the optical efficiency and simplify of the device structure. This device has great potential application for emerging BPLC displays and photonic devices.     

New multicolor and rewritable holographic polymer film for three‐dimensional holographic display

We have developed a new multicolor holographic polymer film. Our holographic polymer film contains 3‐[(2,4,6‐trichloro)azo]‐9H‐carbazole‐9‐ethanol (A‐1) and poly(methyl methacrylate). The holographic polymer film can be recorded with a holographic image without applying an external electric field. The diffraction efficiency was 57% at A‐1 with a 20 wt% of dope ratio. The writable holographic image writing for the holographic polymer film step used the silver halide photographic emulsion master plate 532‐nm laser beam under the nonelectric field. After the copy hologram is formed, our holographic polymer film can be displayed in red and green holographic images. Even though our holographic polymer film is rewritten over 200 times, the diffraction efficiency does not fall. As the holographic polymer film is manufactured using roll‐to‐roll techniques, although still in a laboratory scale in this study, it has a strong possibility of being manufactured in larger sizes with lower cost.     

Triple‐band polarization‐insensitive metamaterial absorber with low profile

In this article, a triple‐band metamaterial low‐profile absorber with polarization independence is proposed. The proposed metamaterial unit cell is composed of two modified rings with square patch at corners. In addition, the proposed absorber is consists of 10 × 10 periodic unit cells with size of 100 mm × 100 mm. To explain the mechanism, the electric field, the surface current distribution, and equivalent circuit model are present. The structure exhibiting three absorption peaks of 99.01%, 97.18%, and 99.53% under normal incidence at 8.92‐9.11 GHz, 13.78‐14.05 GHz and 14.92‐15.21 GHz which cover X and Ku‐band, respectively. In addition, the proposed structure is insensitive for the transverse magnetic/transverse electric field polarization of incident waves and also the angle of incidence. Furthermore, the three operating bands of the absorber can be adjusted independently and offers low profile which makes the design suitable for different curved surface applications. The proposed structure is fabricated and experiments are carried out to validate the design principle. Good agreements are observed between the measured and the corresponding simulated results.     

High‐efficacy drive of spatial positive‐column‐discharge PDP with delayed D pulses

Abstract— A thick‐film ceramic‐sheet PDP provides a long sustain discharge gap of 0.45 mm, enabling the use of positive column discharges. The discharges are established in the middle of the discharge space and are completely free from touching the surface of substrates. This allows for the reduction in diffusion losses of the charged particles. To further improve the efficacy, delayed D pulses are applied to the address electrodes during the sustain period. Although the pulses only draw a little current, they perturb the electric field, reducing the peak discharge current and hence resulting in higher efficacy and luminance. The efficacy and luminance increase by 35% and 38%, respectively, with the delayed D pulses. These pulses are incorporated into the contiguous‐subfield erase‐addressing drive scheme for TV application. A short gap of 70 μm between the sustain and data electrodes generates a fast‐rising discharge and allows a high‐speed addressing of 0.25 μsec. This provides 18 contiguous subfields for the full‐HD single‐scan mode, with 70% light emission duty. A luminous efficacy of 6.0 lm/W can been attained using Ne + 30% Xe 47 kPa, a sustain voltage of 320 V, and a sustain frequency of 3.3 kHz, when the luminance is 157 cd/m². Alternatively, the panel can achieve 4.2 lm/W and 1260 cd/m² by increasing the sustain frequency to 33 kHz.     

Moving‐image‐sticking phenomenon induced by an outside force in liquid‐crystal displays

Abstract— Image deformation caused by an outside force is observed to remain for hours at high gray levels for liquid‐crystal displays (LCDs) in the multi‐domain (MD) vertical‐alignment (VA) mode. This so‐called moving‐image‐sticking phenomenon demonstrated a non‐symmetric luminance profile for the left and right viewing direction for MDVA‐mode LCDs which have original symmetric viewing‐angle characteristics. The generation of a stable reverse‐tilt domain by an outside force was assumed to be the cause of this phenomenon, and the stability of a reverse‐tilt domain under an electric fringe field was calculated by changing the electric‐fringe‐field distribution which determines the LC tilt direction. The domain of a given tilt direction is calculated to change to other tilt direction induced by a fringe field at a low gray condition, but to remain unchanged at a high gray condition. This agrees with the observed trends of duration time of the moving‐image‐sticking phenomenon.     

Low‐temperature‐applicable polymer‐stabilized blue‐phase liquid crystal and its Kerr effect

Abstract— A type of polymer‐stabilized blue‐phase liquid crystal, which can be used in a low‐temperature environment, is proposed. The blue‐phase range after polymerization was widened to more than 73°C, and the blue‐phase texture is very stable even at a temperature as low as ?35°C. The electro‐optical performances dependence on polymer concentration was investigated. The results indicate that the saturation voltage increases and the hysteresis enhances as the polymer concentration increases. The rise and decay times could reach as low as 391 and 789 μsec, respectively. Such material also shows good electro‐optical behavior at a temperature of ?35°C. In addition, the Kerr constant was tested under a uniformly distributed electric field to be 2.195 nm/V² at room temperature and 2.077 nm/V² at ?35°C. The Kerr constant tested under white‐light illumination was 1.975 nm/V², which shows a small dispersion.     

A viewing‐angle‐controllable blue‐phase liquid‐crystal display

Abstract— A viewing‐angle‐controllable liquid‐crystal display (LCD) is proposed. When the device is only driven by an in‐plane electric field, it exhibits a wide‐viewing‐angle (WVA) mode. And it exhibits narrow‐viewing‐angle (NVA) mode when it is driven by a vertical electric field as well as an in‐plane electric field. In this manner, the viewing angle of the device can be controlled from 100° to 30°. The device exhibits a good viewing‐angle‐controlling characteristic and high transmittance.     

Design of a low‐cost 1‐20 GHz magnetic near‐field probe with FR‐4 printed circuit board

An ultra‐wideband magnetic near‐field probe based on a conventional low‐cost four layers of FR‐4 printed circuit board is proposed in this article. It can be used to measure the magnetic near‐field strength from RF magnetic sources or electronic devices for EMI conformance test. The operating frequency of the probe is from 1 GHz up to 20 GHz. The probe is constructed based on a coplanar waveguide and stripline with a short‐end loop. The probe dimension is 10 mm × 25 mm × 0.6 mm. The prototype probe is electric field‐shield structure and has a very high unwanted electric field suppression ratio about 17.7 dB. The probe calibration factor from the simulation agrees well with the calibration factor computed from the measurement. The average probe factor is 38.8 dBS/m and probe sensitivity is 47.4 dB μ A/m.     

Development of a 42‐in. 2‐D/3‐D switchable display using multi‐view technology for public‐information‐display applications

Abstract— A 42‐in. 2‐D/3‐D switchable display operating in a parallax‐barrier‐type system consisting of liquid‐crystal displays (LCDs) has been developed. The system displays 2‐D images in full resolution, without any degradation to the original 2‐D images, and 3‐D autostereoscopic images with resolutions higher than SVGA with wide viewing zones electrically controlled by the parallax‐barrier system. The system is intended for use in public‐information displays (PIDs), a booming field, and as displays for gaming, medical, and simulation applications.     

Wideband dual‐polarized hybrid fed patch antenna

A broadband dual‐polarized patch antenna with hybrid feed structure is proposed in this article. Two different feeding mechanisms are designed to excite two orthogonal modes on a single radiating patch. One of the modes is excited by a magnetic‐coupled feeding structure, while the other is excited by an electric‐coupled feeding structure. The magnetic‐coupled feeding structure consists of a metallic loop with a gap and an open‐ended transmission line. The electric‐coupled feeding structure is composed of a series capacitor and an impedance transformer, which realizes 180° phase shifting. Measured results show that the proposed antenna has 52.3% (1.63~2.78 GHz) and 47.3% (1.68~2.72 GHz) impedance bandwidth with return loss (RL) > 10 dB for port 1 and port 2, respectively. Owing to the hybrid feed structure, the isolation between two ports is better than 26.5 dB. The proposed antenna is suitable for modern wireless communication systems.     

RCS2D: A 2D MoM and FDTD‐based scattering simulator

A Java‐based, two‐dimensional electromagnetic (EM) scattering field simulator—RCS2D—is introduced. It enables one to explore EM wave—arbitrary object interaction under a plane wave illumination. RCS2D uses both method of moments and finite‐difference time‐domain models for both transverse magnetic and transverse electric polarizations. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

Flow‐Induced Inertial Steady Vector Field Topology

Traditionally, vector field visualization is concerned with 2D and 3D flows. Yet, many concepts can be extended to general dynamical systems, including the higher‐dimensional problem of modeling the motion of finite‐sized objects in fluids. In the steady case, the trajectories of these so‐called inertial particles appear as tangent curves of a 4D or 6D vector field. These higher‐dimensional flows are difficult to map to lower‐dimensional spaces, which makes their visualization a challenging problem. We focus on vector field topology, which allows scientists to study asymptotic particle behavior. As recent work on the 2D case has shown, both extraction and classification of isolated critical points depend on the underlying particle model. In this paper, we aim for a model‐independent classification technique, which we apply to two different particle models in not only 2D, but also 3D cases. We show that the classification can be done by performing an eigenanalysis of the spatial derivatives' velocity subspace of the higher‐dimensional 4D or 6D flow. We construct glyphs that depict not only the types of critical points, but also encode the directional information given by the eigenvectors. We show that the eigenvalues and eigenvectors of the inertial phase space have sufficient symmetries and structure so that they can be depicted in 2D or 3D, instead of 4D or 6D.     

Effects of Xe content on wall‐voltage variation during address period in AC plasma‐display panel

Abstract— To investigate the influence of the gas condition, especially xenon (Xe) gas, on the wall‐voltage variation in relation to the electric‐field intensity during the address period, the wall voltages were measured under various Xe‐gas content ranging from 11 to 20% by using the V^t closed curve analysis method. It was observed that under a weak electric‐field intensity between the scan and address electrodes, the change in Xe content did not affect the wall‐voltage variation, even at a higher panel temperature of 65δC. However, under a strong electric‐field intensity, the wall‐voltage variations were reduced with an increase in the Xe content, confirming that a higher electric‐field intensity would be required to induce the wall‐voltage variation at a higher Xe content during the address period.     

Ultra‐fast‐switching flexoelectric liquid‐crystal display with high contrast

Abstract— The flexoelectro‐optic effect provides a fast‐switching mechanism (0.01–0.1 msec), suitable for use in field‐sequential‐color full‐motion‐video displays. An in‐plane electric field is applied to a short‐pitch chiral nematic liquid crystal aligned in the uniform standing helix (or Grandjean) texture. The switching mechanism is experimentally demonstrated in a single‐pixel test cell, and the display performance is investigated as a function of device parameters. A contrast ratio of 2000:1 is predicted.     

3D‐printed cylindrical Luneburg lens antenna for millimeter‐wave applications

A 3D‐printed cylindrical Luneburg lens antenna working at 26 GHz is proposed in this article. The antenna consists of a feeding waveguide, a 3D‐printed cylinder, and a pair of printed metal grids which are stuck on the side faces of the cylinder. 3D‐printed structure ensures the convenience for processing and structural integrity of the Luneburg lens. Hole drilling technology is utilized for the design of the cylindrical lens. In the E‐plane, conversion of spherical waves into planar waves is achieved based on the gradient refractive index which is realized by the gradient equivalent relative dielectric constant. The main part of the lens contains a hole drilling region to realize the desired equivalent permittivity from 1.23 to 2, while another gradual‐thickness region realize the permittivity ranges from 1.23 to 1. H‐probe method is utilized for the optimization of the gradual‐thickness region in this article. And for the H‐plane, with the grids, H‐field distribution is optimized compared with the Luneburg lens antenna without the loading grids. Thus, the side lobe level (SLL) in H‐plane could be reduced. Meanwhile, a narrower half power beamwidth (HPBW) in H‐plane will be obtained due to the metal grids. Experiment results illustrate the feasibility and validity of the proposed 3D‐printed cylindrical Luneburg lens antenna.     

A single‐cell‐gap transflective liquid‐crystal display with special electrodes

Abstract— A single‐cell‐gap transflective liquid‐crystal display with special electrodes was demonstrated. In the transmissive region, a strong longitudinal electric field was generated by decreasing the distance between the top and bottom transparent indium‐tin‐oxide electrodes; while in the reflective region, a weak longitudinal electric field is generated by increasing the distance between the top and bottom transparent indium‐tin‐oxide electrodes. And slit‐patterned electrodes were used to optimize the fringe field at the junction of the transmissive and reflective regions. As a result, both the transmissive and reflective display modes show well‐matched gray scales. The simulated single‐cell‐gap TR‐LCD has good performances.     

Visual Coherence for Large‐Scale Line‐Plot Visualizations

Displaying a large number of lines within a limited amount of screen space is a task that is common to many different classes of visualization techniques such as time‐series visualizations, parallel coordinates, link‐node diagrams, and phase‐space diagrams. This paper addresses the challenging problems of cluttering and overdraw inherent to such visualizations. We generate a 2×2 tensor field during line rasterization that encodes the distribution of line orientations through each image pixel. Anisotropic diffusion of a noise texture is then used to generate a dense, coherent visualization of line orientation. In order to represent features of different scales, we employ a multi‐resolution representation of the tensor field. The resulting technique can easily be applied to a wide variety of line‐based visualizations. We demonstrate this for parallel coordinates, a time‐series visualization, and a phase‐space diagram. Furthermore, we demonstrate how to integrate a focus+context approach by incorporating a second tensor field. Our approach achieves interactive rendering performance for large data sets containing millions of data items, due to its image‐based nature and ease of implementation on GPUs. Simulation results from computational fluid dynamics are used to evaluate the performance and usefulness of the proposed method.